SEARCH · Engineering Papers
Results for “fuel cell technologies”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Real-Time Simulation of Solid Oxide Electrolyzers (SOEC) for Dynamic Operability Improvement and Cyber-Physical System Development
As more intermittent-renewable generations are being added to the power grid, solid oxide electrolysis cells (SOEC) must enhance their rapid load transition capabilities to load follow and support grid resilience. At NETL, we developed real-time SOEC models to research SOEC transients during load step changes. The gained insights can be useful for dynamic operability improvement. These real-time SOEC models also established the basis for cyber-physical SOEC hybrid energy systems. (Virtual presentation to the 2025 MILLENNIUM CLEAN and SUSTAINABLE POWER workshop, University of Genoa, Italy)
Suppressing the enhancement of stimulated Raman scattering in inhomogeneous plasmas by tuning the modulation frequency of a broadband laser
The stimulated Raman scattering (SRS) instability can inhibit the performance of laser driven inertial confinement fusion (ICF) implosions by scattering light into unwanted directions or by generating hot electrons that preheat the target fuel. In principle, ICF target designs can avoid parameter regimes conducive to large, linear SRS gains. In practice, kinetic inflation—the nonlinear enhancement of SRS due to electron trapping in the excited plasma wave—makes this difficult. Here we show that laser bandwidth in the form of frequency modulation can either decrease or increase the inflationary SRS (iSRS) threshold in inhomogeneous plasmas depending on the maximum chirp of the laser pulse. The threshold, mapped out by a series of particle-in-cell simulations, exhibits a minimum when the frequency change within the pulse cancels the spatial detuning due to density inhomogeneities along the trajectory of the scattered light. In conclusion, by tuning the pump laser parameters away from this minimum, the iSRS threshold can be larger than at zero bandwidth, providing a path to mitigating kinetic inflation in ignition relevant plasmas.
Inflationary stimulated Raman scattering in shock-ignition plasmas
In the shock-ignition inertial confinement fusion scheme, high-intensity lasers propagate through an inhomogeneous coronal plasma, driving a shock designed to cause fuel ignition. During the high-intensity ignitor laser pulse, in the long scale length coronal plasma, back-scattered stimulated Raman scattering (SRS) is likely to be in the kinetic regime. In this work, we use one-dimensional particle-in-cell simulations to show that there is a non-linear frequency shift caused by kinetic effects, resulting in the growth of SRS in an inhomogeneous plasma far exceeding the predictions of fluid theory, the so-called inflationary SRS or iSRS. We find that iSRS occurs over a wide range of density scale lengths relevant to shock-ignition and other directly-driven inertial confinement fusion schemes. The presence of iSRS in shock-ignition plasmas has implications for the theoretical gains from shock-ignition inertial confinement fusion. Here, we quantify the intensity threshold for the onset of iSRS for shock-ignition relevant parameters.
Data‐Driven Safety Risk Prediction of Lithium‐Ion Battery
Abstract Inevitable safety issues have pushed battery engineers to become more conservative in battery system design; however, battery‐involved accidents still frequently are reported in headlines. Identifying, understanding, and predicting safety risks have become priorities to further accelerate technology and industry development. However, diverse loading scenarios, significantly varied stress‐induced short circuit mechanisms, and highly coupled mechanical–electrochemical safety behaviors have remained grand challenges. Herein, the safety risk is termed as the probability of the mechanical triggering of an internal short circuit, to reflect the safety related behaviors of lithium‐ion batteries. Based on a mechanical model and experimental results, a sufficient dataset is generated consisting of strain states and their corresponding safety risks, covering both cylindrical and pouch cells, various states of charges, and loading conditions. Machine‐learning tools combined with the established finite element mechanical model are applied to predict the safety risks of the cells. The results achieve a high level of accuracy on the test data (the relative error of the average short circuit prediction deviation is less than 6.2%.). This work underpins the safety risk concept and highlights the promise of physics combined with data‐driven modeling methodology to predict the safety behaviors of energy storage systems.
Enhanced Depolarized Electro-Membrane System (EDEMS) for Direct Capture of Carbon Dioxide from Ambient Air (Final Report)
The goal of this final project report is to summarize the work conducted on project DE-FE0031962. In accordance with the Statement of Project Objectives (SOPO), the University of Kentucky Center for Applied Energy Research (UK CAER) (Recipient) developed an intensified process to capture CO2 from ambient conditions (400 ppm CO2). The process combines low-temperature solvent-aided membrane capture with electrochemically-mediated solvent regeneration to simultaneously capture ambient CO2 while regenerating the solvent. The technology employs only two primary units (regenerator and absorber/contactor) while generating high purity hydrogen as a co-product that can be sold, used for energy storage, or cost-saving depolarization of the direct air capture (DAC) system during the grid peak demand, allowing for flexible operation. When depolarization is employed, the operating voltage is reduced by more than 1 V. Since the technology is powered directly by DC electricity, it can seamlessly tie in with power sources like solar cells without the need for AC/DC converters, therefore allowing for a remote operation to further mitigate greenhouse gas generation toward deploying a negative carbon emissions technology that is completely decoupled from the carbon emissions from the power source for the DAC unit. The project results verified that UK CAER’s integrated approach addressed the complexities of incumbent DAC systems by demonstrating at ambient conditions, including (1) low gas-side pressure-drop facile CO2 capture via a membrane contactor with in-situ generated hydroxide as capture solvent, (2) multi-functional electrochemical regenerator for hydroxide regeneration, CO2 concentration and hydrogen production, and (3) depolarization using cathode-produced hydrogen to reduce energy requirement. The EH&S Assessment of the process did not identify any obvious concern for the bench-scale operation and no apparent barriers to implementing UK CAER’s carbon capture and solvent regeneration system at a larger scale.
TRTR NRAD NRS Beamline Abstract
The Neutron Radiography (NRAD) Reactor is a 250kW TRIGA housed under the largest hot cell in the United States, making it the foremost location to perform neutron imaging of irradiated nuclear fuels and materials, including those intended for use with advanced reactors. Currently, NRAD has two radial beamlines that are used for neutron radiography and tomography. Upgrades to the North neutron beamline include the replacement of the in-tank beam chamber, through-the-wall collimator, and neutron shutter. These beamline upgrades will not only improve image quality for current capabilities but will also condition the beam to be more suitable for advanced methods such as neutron powder diffraction. These upgrades will increase the excess reactivity of the core, reduce unnecessary activation and exposure to workers, and significantly reduce the amount of shielding required around the beam. This presentation will describe how these upgrades improve beam quality, increase utilization of the reactor, and reduce radiation exposure to personnel.
Corrosion testing needs and considerations for additively manufactured materials in nuclear reactors
Metal additive manufacturing holds significant promise as an enabling technology for the 21st century nuclear energy industry. Metal additive manufacturing (MAM) can allow the fabrication of novel materials and innovative component designs that are not achievable through conventional manufacturing. Due to its very different fabrication methods, as-fabricated MAM components are characteristically different from conventionally manufactured components. MAM materials exhibit very different microstructures from conventional cast or wrought materials. For example, austenitic stainless steels fabricated by laser powder bed fusion exhibit columnar grain structures, dislocation cell structures, and melt pool fingerprints. In addition, MAM fabrication may result in defects such as porosity, incomplete processing of the feedstock (e.g., lack of fusion in melt-based methods), and oxide inclusions. Heat treatments may further evolve the microstructure, microsegregation, and stresses within the component. Furthermore, MAM components have a rough surface with feature sizes on the order of the feedstock material, as opposed to smooth surfaces resulting from conventional machining and forming operations. As a result, the corrosion behavior of MAM components will likely be significantly different from that of conventionally formed components. Corrosive environments for structural materials within advanced reactor environments include molten fluoride and chloride salts, liquid sodium and lead-bismuth, and high-temperature helium. The Advanced Materials and Manufacturing Technologies program within the Department of Nuclear Energy in the United States Department of Energy is assessing the unique concerns of MAM component corrosion and testing methodologies in advanced nuclear reactor environments. We discuss these concerns and testing strategies in this paper.
Nanotechnology for catalysis and solar energy conversion
This roadmap on Nanotechnology for Catalysis and Solar Energy Conversion focuses on the application of nanotechnology in addressing the current challenges of energy conversion: 'high efficiency, stability, safety, and the potential for low-cost/scalable manufacturing' to quote from the contributed article by Nathan Lewis. This roadmap focuses on solar-to-fuel conversion, solar water splitting, solar photovoltaics and bio-catalysis. It includes dye-sensitized solar cells (DSSCs), perovskite solar cells, and organic photovoltaics. Smart engineering of colloidal quantum materials and nanostructured electrodes will improve solar-to-fuel conversion efficiency, as described in the articles by Waiskopf and Banin and Meyer. Semiconductor nanoparticles will also improve solar energy conversion efficiency, as discussed by Boschloo et al in their article on DSSCs. Perovskite solar cells have advanced rapidly in recent years, including new ideas on 2D and 3D hybrid halide perovskites, as described by Spanopoulos et al 'Next generation' solar cells using multiple exciton generation (MEG) from hot carriers, described in the article by Nozik and Beard, could lead to remarkable improvement in photovoltaic efficiency by using quantization effects in semiconductor nanostructures (quantum dots, wires or wells). These challenges will not be met without simultaneous improvement in nanoscale characterization methods. Terahertz spectroscopy, discussed in the article by Milot et al is one example of a method that is overcoming the difficulties associated with nanoscale materials characterization by avoiding electrical contacts to nanoparticles, allowing characterization during device operation, and enabling characterization of a single nanoparticle. Besides experimental advances, computational science is also meeting the challenges of nanomaterials synthesis. The article by Kohlstedt and Schatz discusses the computational frameworks being used to predict structure–property relationships in materials and devices, including machine learning methods, with an emphasis on organic photovoltaics. The contribution by Megarity and Armstrong presents the 'electrochemical leaf' for improvements in electrochemistry and beyond. In addition, biohybrid approaches can take advantage of efficient and specific enzyme catalysts. These articles present the nanoscience and technology at the forefront of renewable energy development that will have significant benefits to society.
Perspectives of Open-Air Processing to Enable Perovskite Solar Cell Manufacturing
We report high throughput open-air processing techniques for the scalable production of all device and barrier layers for perovskite photovoltaics (PV). This work discusses and resolves some of the most formidable barriers to module-level scaling that the perovskite community has been facing. Our advanced technoeconomic manufacturing analysis indicates that vacuum-based processes with high capital expenditures (CapEx) and low throughputs dominate the cost of production. Open-air fabrication methods offer low CapEx routes to manufacturing, but achieving reproducibility in ambient conditions with varying relative humidity has been a persistent challenge. The use of rapid processing methods with plasma curing to convert films from the solution-state enables reproducibility, moisture immunity, and the highest perovskite PV efficiency produced in open-air. These methods are readily translatable to in-line processing where layers are sequentially deposited without the need for lengthy post-annealing steps that reduce throughput and involve additional equipment. Significant progress is demonstrated in reduced manufacturing costs as perovskites contend as a commercially viable next-generation thin film PV technology.
Transforming Energy Through Sustainable Mobility: Expanding Low-Carbon Transportation R&D Solutions
As the nation's premier laboratory for cutting-edge transportation decarbonization research and development solutions, the National Renewable Energy Laboratory (NREL) pioneers the creation and deployment of sustainable mobility technologies and strategies, with a focus on slashing transportation sector greenhouse gas emissions and combatting climate change. Trucks, planes, cargo ships, and other difficult-to-decarbonize vehicles are part of this essential transition for the transportation sector, which is currently the nation's largest source of the greenhouse gas emissions. NREL provides the scientific building blocks needed to spur innovation through multifaceted analysis, research, and engineering. This work acts as a catalyst to help industry bring affordable, high-performance, energy-efficient, and low-emission modes of transport and related infrastructure to market sooner. Our researchers collaborate closely with academic, government, and industry partners to design better batteries, drivetrains, and engines. They develop technologies for high-power charging, thermal management, energy storage, and power electronics. They are also reimagining fuels and combustion while creating sustainable lightweight materials. Unbiased expert guidance - backed by credible data and analysis, tools, and scientific rigor - empowers partners to make informed decisions about sustainable transportation. NREL recognizes that communities with limited mobility options face reduced access to employment opportunities, health care, and education, lowering overall quality of life. Alongside partners, NREL experts are creating transportation solutions that meet community-identified needs and increase mobility equity in historically underserved and overburdened communities. Rather than providing a one-size-fits-all solution, we take an interdisciplinary approach to mobility equity that considers the needs and challenges of diverse groups, maximizing benefits at the individual, community, and societal levels.
Verification of a Monte Carlo binary collision model for simulating elastic and inelastic collisions in particle-in-cell simulations
We present the development and verification of a Monte Carlo binary collision model for simulating elastic and inelastic collisions in particle-in-cell simulations. We apply the corrected binary collision model originally developed for charged-particles collisions to all considered scattering channels, including Coulomb collisions, elastic neutral–neutral and charged–neutral collisions, ionization, excitation, and fusion. The model's implementation is described and verified through a series of simulations, including charged- and neutral-particle thermal equilibration, slowing of electrons in warm solid-density aluminum, collisional damping of a Langmuir wave, helium gas breakdown in an applied electric field, and thermonuclear and beam–target fusion. Then, we demonstrate the model within simulations of hydrogen plasma formation in the Princeton Field-Reversed Configuration as well as of the burning of aneutronic fusion fuel p-11B. The latter includes measurement of the fusion power density in a low-density plasma and fusion production due to the stopping of a proton ignitor beam in a compressed boron target.
Modeling oxygen reduction activity loss mechanisms in atomically dispersed Fe–N–C electrocatalysts
Materials degradation is a major factor that limits the wider adoption of renewable and clean energy technologies. This is particularly true for the Pt group metal-free (PGM-free) atomically dispersed metal-nitrogen-carbon (M-N-C) catalysts. Here, while many experimental studies have investigated and reported the phenomenological aspects of M-N-C degradation, only a few modeling studies have considered degradation mechanisms at the atomic level. Understanding the mechanisms responsible for activity loss occurring in atomically dispersed M-N-C’s is crucial towards rationally designing active, durable, and less expensive Earth-abundant catalysts. Towards this end, we have surveyed recent literature concerning the modeling of corrosion mechanisms that impact M-N-C catalysts (Fe–N–C, in particular) and offer our own perspectives on the future direction of this field.
High-temperature low-humidity proton exchange membrane with “stream-reservoir” ionic channels for high-power-density fuel cells
The perfluorosulfonic acid (PFSA) proton exchange membrane (PEM) is the key component for hydrogen fuel cells (FCs). We used in situ synchrotron scattering to investigate the PEM morphology evolution and found a “stream-reservoir” morphology, which enables efficient proton transport. The short-side-chain (SSC) PFSA PEM is fabricated under the guidance of morphology optimization, which delivered a proton conductivity of 193 milliSiemens per centimeter [95% relativity humidity (RH)] and 40 milliSiemens per centimeter (40% RH) at 80°C. The improved glass transition temperature, water permeability, and mechanical strength enable high-temperature low-humidity FC applications. Performance improvement by 82.3% at 110°C and 25% RH is obtained for SSC-PFSA PEM FCs compared to Nafion polymer PEM devices. The insights in chain conformation, packing mechanism, crystallization, and phase separation of PFSAs build up the structure-property relationship. In addition, SSC-PFSA PEM is ideal for high-temperature low-humidity FCs that are needed urgently for high-power-density and heavy-duty applications.
Freezing water at constant volume and under confinement
Water expands upon freezing. What happens when water is cooled below 0 °C in an undeformable, constant-volume container? This is a fundamental question in materials thermodynamics, and is also relevant in biological, geological, and technological applications in which ice forms under nano-, meso-, or macroscale confinement. Here, we analyze the phase-equilibria and kinetic behaviors of water and ice-1h in an isochoric (constant-volume) system. By making use of the Helmholtz potential F (temperature, volume), in contrast to the Gibbs potential G (temperature, pressure), we demonstrate significant changes in phase behavior when the specific volume of the container is constrained below that of ice-1h. We construct a T–V (temperature–volume) phase diagram for water and ice that features a broad two-phase equilibrium region, and we further derive an isochoric nucleation theory that reveals the existence of a critical confinement volume, on the order of microns, below which ice-1h is kinetically prohibited from forming.
Elevated Temperature Graphite Mechanical Testing
High purity graphite will be used for core components within most High Temperature Reactor (HTR) designs. Several "high tech” industries currently utilize synthetic, high-purity, commercially available graphite components to fabricate photovoltaic cells, semi-conductors, optical fibers, and other high value electronic industry products. New advanced HTR designs are also interested in using these graphite grades for long-term, internal core component applications. Consequently, the US Department of Energy, Advanced Reactor Technologies (DOE-ART) program has spent several years testing different high purity graphite grades for potential use within these new nuclear reactor designs. A significant part of that effort has been in the development and improvement of American Society for Testing and Materials (ASTM) test standards specifically for nuclear graphite grades. Nearly all ASTM test standards have either been developed or improved by the DOE-ART program over the past 25 years. The ART program continues to assist in the development of new ASTM test standards in support of the future commercial HTR fleet currently being designed and built in the USA. The newest effort undertaken by ART is the development of high temperature mechanical testing practices that may be acceptable for a future ASTM test standard (or guide) for this critical material property measurement.
Modulating Electronic Structure of Atomically Dispersed Nickel Sites through Boron and Nitrogen Dual Coordination Boosts Oxygen Reduction
Abstract Atomically dispersed 3D transitional metal active sites with nitrogen coordination anchored on carbon support have emerged as a kind of promising electrocatalyst toward oxygen reduction reaction (ORR) in the field of fuel cells and metal–air cells. However, it is still a challenge to accurately modulate the coordination structure of single‐atom metal sites, especially first‐shell coordination, as well as identify the relationship between the geometric/electronic structure and ORR performance. Herein, a carbon‐supported single‐atom nickel catalyst is fabricated with boron and nitrogen dual coordination (denoted as Ni‐B/N‐C). The hard X‐ray absorption spectrum result reveals that atomically dispersed Ni active sites are coordinated with one B atom and three N atoms in the first shell (denoted as Ni‐B 1 N 3 ). The Ni‐B/N‐C catalyst exhibits a half‐wave potential ( E 1/2 ) of 0.87 V versus RHE, along with a distinguished long‐term durability in alkaline media, which is superior to commercial Pt/C. Density functional theory calculations indicate that the Ni‐B 1 N 3 active sites are more favorable for the adsorption of ORR intermediates relative to Ni‐N 4 , leading to the reduction of thermodynamic barrier and the acceleration of reaction kinetics, which accounts for the increased intrinsic activity.
Understanding the impact of an applied axial magnetic field on efficient current coupling on the Z machine
Magnetized liner inertial fusion (MagLIF) is an attractive concept for producing thermonuclear fusion reactions. The MagLIF platform involves the operation of Helmholtz coils to apply a 15 Tesla axial magnetic field to the load region, where a cylindrical, fuel-filled metal liner is imploded by a ∼ 2 0 MA current pulse. The fringe field from these coils extends into the transmission line that delivers the current to the target. We investigated the extent to which this applied field disturbs the nominal power flow within that transmission line. A simplified model of the geometry shows that adding the applied magnetic field results in magnetic field lines that connect the cathode to the anode, suggesting electrons may not be magnetically insulated in this region. Particle-in-cell simulations indicated the addition of the applied magnetic field would not significantly impact the current delivery to the load. Velocimetry was used to experimentally assess the current delivery with and without the applied magnetic field. We find no measurable effects of the applied field on current delivery in the configuration investigated in this study. Published by the American Physical Society 2024