Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flight computing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

20 plus Years of Computational Fluid Dynamics for the Space Shuttle

This slide presentation reviews the use of computational fluid dynamics in performing analysis of the space shuttle with particular reference to the return to flight analysis and other shuttle problems. Slides show a comparison of pressure coefficient with the shuttle ascent configuration between the wind tunnel test and the computed values. the evolution of the grid system for the space shuttle launch vehicle (SSLv) from the early 80's to one in 2004, the grid configuration of the bipod ramp redesign from the original design to the current configuration, charts with the computations showing solid rocket booster surface pressures from wind tunnel data, calculated over two grid systems (i.e., the original 14 grid system, and the enhanced 113 grid system), and the computed flight orbiter wing loads are compared with strain gage data on STS-50 during flight. The loss of STS-107 initiated an unprecedented review of all external environments. The current SSLV grid system of 600+ grids, 1.8 Million surface points and 95+ million volume points is shown. The inflight entry analyses is shown, and the use of Overset CFD as a key part to many external tank redesign and debris assessments is discussed. The work that still remains to be accomplished for future shuttle flights is discussed.

Gomez, Reynaldo J., III↗

Air-breathing aerospace plane development essential: Hypersonic propulsion flight tests

Hypersonic airbreathing propulsion utilizing scramjets can change transatmospheric accelerators for low earth-to-orbit and return transportation. The value and limitation of ground tests, of flight tests, and of computations are presented, and scramjet development requirements are discussed. It is proposed that near full-scale hypersonic propulsion flight tests are essential for developing computational design technology so that it can be used for designing this system. In order to determine how these objectives should be achieved, some lessons learned from past programs are presented. A conceptual two-stage-to-orbit (TSTO) prototype/experimental aerospace plane is recommended as a means of providing access-to-space and for conducting flight tests.

Mehta, Unmeel B.↗

A Simulation Study of Bin-and-Sort Policies in a Distributed System for Flights Scheduling

This is a report on the results of a simulation experiment conducted on an automated distributed system for scheduling flights in a shared airspace. The scheduling is carried out by computer systems owned by the private operators of the flights, which interface through a centralized independent server. The scheduling requires determining which of the group of flights at hand (whether owned by the same operator or different ones) are to have the advantage of being scheduled before the others. A chosen method of grouping and prioritizing flights must: have the ability to schedule a flight promptly, prevent scheduling conflicts between pairs of overlapping flight routes, and be computationally feasible. Scheduling flights one by one is the First Come First Served policy. Scheduling too many at a time is infeasible. The type of scheduling policy proposed herein, called bin-and-sort, is an attempt to reach a compromise between these two extremes. Bin-and-sort allows for each operator to choose its criteria for prioritizing its flights, and for the centralized component to use different arbitration criteria. A number of these criteria are used in the simulation presented herein. The results of each criterion choice are reported and analyzed.

flight scheduling↗

A Simulation Study of Bin-and-Sort Policies in a Distributed System for Flights Scheduling

This is a report on the results of a simulation experiment conducted on an automated distributed system for scheduling flights in a shared airspace. The scheduling is carried out by computer systems owned by the private operators of the flights, which interface through a centralized independent server. The scheduling requires determining which of the group of flights at hand (whether owned by the same operator or different ones) are to have the advantage of being scheduled before the others. A chosen method of grouping and prioritizing flights must: have the ability to schedule a flight promptly, prevent scheduling conflicts between pairs of overlapping flight routes, and be computationally feasible. Scheduling flights one by one is the First Come First Served policy. Scheduling too many at a time is infeasible. The type of scheduling policy proposed herein, called bin-and-sort, is an attempt to reach a compromise between these two extremes. Bin-and-sort allows for each operator to choose its criteria for prioritizing its flights, and for the centralized component to use different arbitration criteria. A number of these criteria are used in the simulation presented herein. The results of each criterion choice are reported and analyzed.

flight scheduling↗

Aerodynamic Interference Due to MSL Reaction Control System

An investigation of effectiveness of the reaction control system (RCS) of Mars Science Laboratory (MSL) entry capsule during atmospheric flight has been conducted. The reason for the investigation is that MSL is designed to fly a lifting actively guided entry with hypersonic bank maneuvers, therefore an understanding of RCS effectiveness is required. In the course of the study several jet configurations were evaluated using Langley Aerothermal Upwind Relaxation Algorithm (LAURA) code, Data Parallel Line Relaxation (DPLR) code, Fully Unstructured 3D (FUN3D) code and an Overset Grid Flowsolver (OVERFLOW) code. Computations indicated that some of the proposed configurations might induce aero-RCS interactions, sufficient to impede and even overwhelm the intended control torques. It was found that the maximum potential for aero-RCS interference exists around peak dynamic pressure along the trajectory. Present analysis largely relies on computational methods. Ground testing, flight data and computational analyses are required to fully understand the problem. At the time of this writing some experimental work spanning range of Mach number 2.5 through 4.5 has been completed and used to establish preliminary levels of confidence for computations. As a result of the present work a final RCS configuration has been designed such as to minimize aero-interference effects and it is a design baseline for MSL entry capsule.

Dyakonov, Artem A.↗

Aerodynamic Parameter Estimation for the X-43A (Hyper-X) from Flight Data

Aerodynamic parameters were estimated based on flight data from the third flight of the X-43A hypersonic research vehicle, also called Hyper-X. Maneuvers were flown using multiple orthogonal phase-optimized sweep inputs applied as simultaneous control surface perturbations at Mach 8, 7, 6, 5, 4, and 3 during the vehicle descent. Aerodynamic parameters, consisting of non-dimensional longitudinal and lateral stability and control derivatives, were estimated from flight data at each Mach number. Multi-step inputs at nearly the same flight conditions were also flown to assess the prediction capability of the identified models. Prediction errors were found to be comparable in magnitude to the modeling errors, which indicates accurate modeling. Aerodynamic parameter estimates were plotted as a function of Mach number, and compared with estimates from the pre-flight aerodynamic database, which was based on wind-tunnel tests and computational fluid dynamics. Agreement between flight estimates and values computed from the aerodynamic database was excellent overall.

Morelli, Eugene A.↗

SAD5 Stereo Correlation Line-Striping in an FPGA

High precision SAD5 stereo computations can be performed in an FPGA (field-programmable gate array) at much higher speeds than possible in a conventional CPU (central processing unit), but this uses large amounts of FPGA resources that scale with image size. Of the two key resources in an FPGA, Slices and BRAM (block RAM), Slices scale linearly in the new algorithm with image size, and BRAM scales quadratically with image size. An approach was developed to trade latency for BRAM by sub-windowing the image vertically into overlapping strips and stitching the outputs together to create a single continuous disparity output. In stereo, the general rule of thumb is that the disparity search range must be 1/10 the image size. In the new algorithm, BRAM usage scales linearly with disparity search range and scales again linearly with line width. So a doubling of image size, say from 640 to 1,280, would in the previous design be an effective 4 of BRAM usage: 2 for line width, 2 again for disparity search range. The minimum strip size is twice the search range, and will produce an output strip width equal to the disparity search range. So assuming a disparity search range of 1/10 image width, 10 sequential runs of the minimum strip size would produce a full output image. This approach allowed the innovators to fit 1280 960 wide SAD5 stereo disparity in less than 80 BRAM, 52k Slices on a Virtex 5LX330T, 25% and 24% of resources, respectively. Using a 100-MHz clock, this build would perform stereo at 39 Hz. Of particular interest to JPL is that there is a flight qualified version of the Virtex 5: this could produce stereo results even for very large image sizes at 3 orders of magnitude faster than could be computed on the PowerPC 750 flight computer. The work covered in the report allows the stereo algorithm to run on much larger images than before, and using much less BRAM. This opens up choices for a smaller flight FPGA (which saves power and space), or for other algorithms in addition to SAD5 to be run on the same FPGA.

Villalpando, Carlos Y.↗

Two-dimensional computational analysis of a transport high-lift system and a comparison with flight-test results

Two currently available coupled inviscid/viscous multielement computational codes, including a relatively simple panel method and an Euler method, are used to analyze a high-lift system. The results are compared with two-dimensional wind-tunnel test results and then with the three-dimensional flight-test results obtained from the NASA Langley Transport Systems Research Vehicle five-element high-lift wing section. Comparisons were also made between the panel method, the Euler method, and flight data for two high-lift configurations, one representing a take-off configuration and the other an approach configuration. For the take-off configuration, both codes agreed reasonably well with experimental data, but both codes were found to overpredict the flap upper-surface pressures for the approach configuration.

Hardin, Jay D.↗

Development and evaluation of an airplane electronic display format aligned with the inertial velocity vector

The development of an electronic primary flight display format aligned with the aircraft velocity vector, a simulation evaluation comparing this format with an electronic attitude-aligned primary flight display format, and a flight evaluation of the velocity-vector-aligned display format are described. Earlier tests in turbulent conditions with the electronic attitude-aligned display format had exhibited unsteadiness. A primary objective of aligning the display format with the velocity vector was to take advantage of a velocity-vector control-wheel steering system to provide steadiness of display during turbulent conditions. Better situational awareness under crosswind conditions was also achieved. The evaluation task was a curved, descending approach with turbulent and crosswind conditions. Primary flight display formats contained computer-drawn perspective runway images and flight-path angle information. The flight tests were conducted aboard the NASA Transport Systems Research Vehicle (TSRV). Comparative results of the simulation and flight tests were principally obtained from subjective commentary. Overall, the pilots preferred the display format aligned with the velocity vector.

Steinmetz, G. G.↗

Knowledge-Acquisition Tool For Expert System

Digital flight-control systems monitored by computer program that evaluates and recommends. Flight-systems engineers for advanced, high-performance aircraft use knowlege-acquisition tool for expert-system flight-status monitor suppling interpretative data. Interpretative function especially important in time-critical, high-stress situations because it facilitates problem identification and corrective strategy. Conditions evaluated and recommendations made by ground-based engineers having essential knowledge for analysis and monitoring of performances of advanced aircraft systems.

Disbrow, James D.↗

Check-Cases for Verification of 6-Degree-of-Freedom Flight Vehicle Simulations

The rise of innovative unmanned aeronautical systems and the emergence of commercial space activities have resulted in a number of relatively new aerospace organizations that are designing innovative systems and solutions. These organizations use a variety of commercial off-the-shelf and in-house-developed simulation and analysis tools including 6-degree-of-freedom (6-DOF) flight simulation tools. The increased affordability of computing capability has made highfidelity flight simulation practical for all participants. Verification of the tools' equations-of-motion and environment models (e.g., atmosphere, gravitation, and geodesy) is desirable to assure accuracy of results. However, aside from simple textbook examples, minimal verification data exists in open literature for 6-DOF flight simulation problems. This assessment compared multiple solution trajectories to a set of verification check-cases that covered atmospheric and exo-atmospheric (i.e., orbital) flight. Each scenario consisted of predefined flight vehicles, initial conditions, and maneuvers. These scenarios were implemented and executed in a variety of analytical and real-time simulation tools. This tool-set included simulation tools in a variety of programming languages based on modified flat-Earth, round- Earth, and rotating oblate spheroidal Earth geodesy and gravitation models, and independently derived equations-of-motion and propagation techniques. The resulting simulated parameter trajectories were compared by over-plotting and difference-plotting to yield a family of solutions. In total, seven simulation tools were exercised.

Murri, Daniel G.↗

Thermal calibration and analysis of a Bridgman flight furnace

A combination of computer modeling and experimental measurements is proposed which permits the calibration of the temperature profile for a spacecraft flight furnace. The Fluent code based on the finite difference method uses the furnace set-point temperatures as boundary conditions to model a Bridgman directional solidification furnace. Experimental measurements are employed as a comparison for the numerical analysis, and the radial gradients and wall temperatures are selected when the calculated values are sufficiently close to those from measurements. The calculations are found to agree with experimental data, and some results of the modeling are given which relate to specific furnace parameters. The CFD approach facilitates the transposition of furnace calibration to microgravitational operation in addition to providing precise initial radial temperature gradients and furnace-wall temperatures.

Knuteson, D. J.↗

Progress in knowledge-based flight monitoring

Features and applications of the script-based flight monitor SECURE are described. Implemented on an on-board computer, SECURE treats a flight as a regular sequence of contexts (situations) defined in a knowledge base with a hierarchical structure for successively more finely delineated flight phases, i.e., takeoff, cruise and landing. SECURE provides normalcy references for flight monitoring and allows context identification, which allows the presentation of checklists. An implementation of SECURE, written in MACLISP, on a DC-10 flight simulator is described.

Chen, D. C.↗

Computational support of the X-29A Advanced Technology Demonstrator flight experiment

Issues and questions associated with the forward swept wing and closely coupled canard are addressed. The primary focus will be on research questions which must be addressed to obtain high quality ground and flight test data. These data will be used in conjunction with computational predictions to complement the analyses required to comprehensively understand the interacting technologies.

Waggoner, E. G.↗

Lidar Remote Sensing of Forests: New Instruments and Modeling Capabilities

Lidar instruments provide scientists with the unique opportunity to characterize the 3D structure of forest ecosystems. This information allows us to estimate properties such as wood volume, biomass density, stocking density, canopy cover, and leaf area. Structural information also can be used as drivers for photosynthesis and ecosystem demography models to predict forest growth and carbon sequestration. All lidars use time-in-flight measurements to compute accurate ranging measurements; however, there is a wide range of instruments and data types that are currently available, and instrument technology continues to advance at a rapid pace. This seminar will present new technologies that are in use and under development at NASA for airborne and space-based missions. Opportunities for instrument and data fusion will also be discussed, as Dr. Cook is the PI for G-LiHT, Goddard's LiDAR, Hyperspectral, and Thermal airborne imager. Lastly, this talk will introduce radiative transfer models that can simulate interactions between laser light and forest canopies. Developing modeling capabilities is important for providing continuity between observations made with different lidars, and to assist the design of new instruments. Dr. Bruce Cook is a research scientist in NASA's Biospheric Sciences Laboratory at Goddard Space Flight Center, and has more than 25 years of experience conducting research on ecosystem processes, soil biogeochemistry, and exchange of carbon, water vapor and energy between the terrestrial biosphere and atmosphere. His research interests include the combined use of lidar, hyperspectral, and thermal data for characterizing ecosystem form and function. He is Deputy Project Scientist for the Landsat Data Continuity Mission (LDCM); Project Manager for NASA s Carbon Monitoring System (CMS) pilot project for local-scale forest biomass; and PI of Goddard's LiDAR, Hyperspectral, and Thermal (G-LiHT) airborne imager.

Cook, Bruce D.↗

Experimental, Theoretical, and Computational Investigation of Separated Nozzle Flows

A detailed experimental, theoretical, and computational study of separated nozzle flows has been conducted. Experimental testing was performed at the NASA Langley 16-Foot Transonic Tunnel Complex. As part of a comprehensive static performance investigation, force, moment, and pressure measurements were made and schlieren flow visualization was obtained for a sub-scale, non-axisymmetric, two-dimensional, convergent- divergent nozzle. In addition, two-dimensional numerical simulations were run using the computational fluid dynamics code PAB3D with two-equation turbulence closure and algebraic Reynolds stress modeling. For reference, experimental and computational results were compared with theoretical predictions based on one-dimensional gas dynamics and an approximate integral momentum boundary layer method. Experimental results from this study indicate that off-design overexpanded nozzle flow was dominated by shock induced boundary layer separation, which was divided into two distinct flow regimes; three- dimensional separation with partial reattachment, and fully detached two-dimensional separation. The test nozzle was observed to go through a marked transition in passing from one regime to the other. In all cases, separation provided a significant increase in static thrust efficiency compared to the ideal prediction. Results indicate that with controlled separation, the entire overexpanded range of nozzle performance would be within 10% of the peak thrust efficiency. By offering savings in weight and complexity over a conventional mechanical exhaust system, this may allow a fixed geometry nozzle to cover an entire flight envelope. The computational simulation was in excellent agreement with experimental data over most of the test range, and did a good job of modeling internal flow and thrust performance. An exception occurred at low nozzle pressure ratios, where the two-dimensional computational model was inconsistent with the three-dimensional separation observed in the experiment. In general, the computation captured the physics of the shock boundary layer interaction and shock induced boundary layer separation in the nozzle, though there were some differences in shock structure compared to experiment. Though minor, these differences could be important for studies involving flow control or thrust vectoring of separated nozzles. Combined with other observations, this indicates that more detailed, three-dimensional computational modeling needs to be conducted to more realistically simulate shock-separated nozzle flows.

Hunter, Craig A.↗