SEARCH · Engineering Papers

Results for “field validation results”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Elastic-plastic conductor damage evaluation at over 0.4% strain using a high-stress REBCO coil

Abstract Recent reports on screening current stress simulations of high-field REBCO magnets frequently present peak stresses over 1 GPa. However, this result is probably an unrealistic artifact of purely elastic calculations, considering the macroscopic yield and fracture stresses of approximately 900 MPa and less than 1.1 GPa for Hastelloy substrate-coated conductors. Here, we evaluate elastic-plastic conductor damage at over 0.4% strain using a high-stress REBCO coil exposed to a high field to explore this elastic-plastic regime. The coil was located off-center in a low-temperature superconductor magnet so as to induce a significant screening current in the enhanced radial field. Voltage taps, a Hall sensor, and two strain gauges were used for the instrumentation. We obtained strains exceeding 0.4% near the outward edge during the coil current charge from 350 A to 390 A, where the coil was exposed to external axial and radial magnetic fields of 13 T and 0.5 T. Post mortem results showed wavy plastic deformation, electrical damage, and REBCO defects. An elastic-plastic simulation reproduced the measured strains and predicted that ∼1 GPa stress is sufficient to induce ∼0.9% strain, thus validating our initial concerns with purely elastic models. This paper provides our experimental and simulation results.

Bang, Jeseok (ORCID:0000000247616334)↗

DOE OSTI2023

New constraints on cosmological modified gravity theories from anisotropic three-point correlation functions of BOSS DR12 galaxies

Here we report a new test of modified gravity theories using the large-scale structure of the Universe. This paper is the first attempt to (1) apply a joint analysis of the anisotropic components of galaxy two- and three-point correlation functions (2 and 3PCFs) to actual galaxy data and (2) constrain the non-linear effects of degenerate higher-order scalar-tensor (DHOST) theories on cosmological scales. Applying this analysis to the Baryon Oscillation Spectroscopic Survey (BOSS) data release 12, we obtain the lower bounds of –1.655 < ξ t and –0.504 < ξ s at the $95{{\ \rm per\ cent}}$ confidence level on the parameters characterizing the time evolution of the tidal and shift terms of the second-order velocity field. These constraints are consistent with GR predictions of ξ t = 15/1144 and ξs = 0. Moreover, they represent a 35-fold and 20-fold improvement, respectively, over the joint analysis with only the isotropic 3PCF. We ensure the validity of our results by investigating various quantities, including theoretical models of the 3PCF, window function corrections, cumulative S/N, Fisher matrices, and statistical scattering effects of mock simulation data. We also find statistically significant discrepancies between the BOSS data and the Patchy mocks for the 3PCF measurement. Finally, we package all of our 3PCF analysis codes under the name hitomi and make them publicly available so that readers can reproduce all the results of this paper and easily apply them to ongoing future galaxy surveys.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2022

Measurement and Simulation of the Magnetic Fields from a 555 Timer Integrated Circuit Using a Quantum Diamond Microscope and Finite-Element Analysis

Quantum diamond microscope (QDM) magnetic field imaging is an emerging interrogation and diagnostic technique for integrated circuits (ICs). To date, the ICs measured with a QDM have been either too complex for us to predict the expected magnetic fields and benchmark the QDM performance or too simple to be relevant to the IC community. In this paper, we establish a 555 timer IC as a “model system” to optimize QDM measurement implementation, benchmark performance, and assess IC device functionality. To validate the magnetic field images taken with a QDM, we use a spice electronic circuit simulator and finite-element analysis (FEA) to model the magnetic fields from the 555 die for two functional states. Furthermore, we compare the advantages and the results of three IC-diamond measurement methods, confirm that the measured and simulated magnetic images are consistent, identify the magnetic signatures of current paths within the device, and discuss using this model system to advance QDM magnetic imaging as an IC diagnostic tool.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2022

Electron Density Changes across the Pressure-Induced Iron Spin Transition

High-pressure single-crystal x-ray diffraction is used to experimentally map the electron-density distribution changes in (Fe,Mg)O as ferrous iron undergoes a pressure-induced transition from high- to low-spin states. As the bulk density and elasticity of magnesiowustite—one of the dominant mineral phases of Earth’s mantle—are affected by this electronic transition, our results have applications to geophysics as well as to validating first-principles calculations. Furthermore, the observed changes in diffraction intensities indicate a spin-transition-induced change in orbital occupancies of the Fe ion in general accord with crystal-field theory, illustrating the use of electron density measurements for characterizing high-pressure d-block chemistry and motivating further studies characterizing chemical bonding under pressure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Validation of High Resolution Atmospheric and Dispersion Simulations

Weather models typically operate on averages of 1 km or more. This averages out fine scale turbulence. This results in smooth laminar flows and rapid vertical motions are usually averaged out. In this study, those fine scaled features were simulated for a 2013 field study of transport and diffusion of a tracer gas. Parameterized subgrid turbulence was required to produce dilution representative of observations. Despite this, the simulation with the finest grid and contained parameterized subgrid turbulence produced dilution that was consistent with observations.

THOMAS, ANDREW↗

NASA NTRS1986

Active-passive airborne ocean color measurement. II - Applications

Reported here for the first time is the use of a single airborne instrument to make concurrent measurements of oceanic chlorophyll concentration by (1) laser-induced fluorescence, (2) passive upwelling radiance, and (3) solar-induced chlorophyll fluorescence. Results from field experiments conducted with the NASA airborne oceanographic lidar (AOL) in the New York Bight demonstrate the capability of a single active-passive instrument to perform new and potentially important ocean color studies related to (1) active lidar validation of passive ocean color in-water algorithms, (2) chlorophyll a in vivo fluorescence yield variability, (3) calibration of active multichannel lidar systems, (4) effect of sea state on passive and active ocean color measurements, (5) laser/solar-induced chlorophyll fluorescence investigations, and (6) subsequent improvement of satellite-borne ocean color scanners. For validation and comparison purposes a separate passive ocean color sensor was also flown along with the new active-passive sensor during these initial field trials.

Hoge, F. E.↗

NASA NTRS1993

Unsteady panel method for flows with multiple bodies moving along various paths

A potential flow based three-dimensional panel method was modified to treat time dependent conditions in which several submerged bodies can move within the fluid along different trajectories. This modification was accomplished by formulating the momentary solution in an inertial frame-of-reference, attached to the undisturbed stationary fluid. Consequently, the numerical interpretation of the multiple-body, solid-surface boundary condition and the viscous wake rollup was considerably simplified. The unsteady capability of this code was validated by comparing computed and experimental results for a finite wing undergoing pitch oscillations. In order to demonstrate the multicomponent capability, computations were made for two wings following closely intersecting paths (e.g., to avoid mid air collisions) and for a flow field with relative rotation (e.g., helicopter-rotor/fuselage interaction). Results were compared to experimental data when such data was available.

Richason, Thomas F.↗

NASA NTRS2000

Comprehensive Evaluation of Attitude and Orbit Estimation Using Actual Earth Magnetic Field Data

A single, augmented Extended Kalman Filter (EKF), which simultaneously and autonomously estimates spacecraft attitude and orbit has been developed and successfully tested with real magnetometer and gyro data only. Because the earth magnetic field is a function of time and position, and because time is known quite precisely, the differences between the computed and measured magnetic field components, as measured by the magnetometers throughout the entire spacecraft orbit, are a function of both orbit and attitude errors. Thus, conceivably these differences could be used to estimate both orbit and attitude; an observability study validated this assumption. The results of testing the EKF with actual magnetometer and gyro data, from four satellites supported by the NASA Goddard Space Flight Center (GSFC) Guidance, Navigation, and Control Center, are presented and evaluated. They confirm the assumption that a single EKF can estimate both attitude and orbit when using gyros and magnetometers only.

Deutschmann, Julie K.↗

NASA NTRS2003

Development of a Fatigue Crack Growth Coupon for Highly Plastic Stress Conditions

This paper presents an analytical approach used to develop a novel fatigue crack growth coupon for a highly plastic 3-D stress field condition. The flight hardware investigated in this paper is a large separation bolt that fractures using pyrotechnics at the appointed time during the flight sequence. The separation bolt has a deep notch that produces a severe stress concentration and a large plastic zone when highly loaded. For this geometry, linear-elastic fracture mechanics (LEFM) techniques are not valid due to the large nonlinear stress field. Unfortunately, industry codes that are generally available for fracture mechanics analysis and fatigue crack growth (e.g. NASGRO (11) are limited to LEFM and are available for only a limited number of geometries. The results of LEFM based codes are questionable when used on geometries with significant plasticity. Therefore elastic-plastic fracture mechanics (EPFM) techniques using the finite element method (FEM) were used to analyze the bolt and test coupons. scale flight hardware is very costly in t e r n of assets, laboratory resources, and schedule. Therefore to alleviate some of these problems, a series of novel test coupons were developed to simulate the elastic-plastic stress field present in the bolt.

Allen, Phillip A.↗

NASA NTRS2015

Near-Field Acoustic Power Level Analysis of F31/A31 Open Rotor Model at Simulated Cruise Conditions, Technical Report II

Near-field acoustic power level analysis of F31A31 open rotor model has been performed to determine its noise characteristics at simulated cruise flight conditions. The non-proprietary parts of the test data obtained from experiments in the 8x6 supersonic wind tunnel were provided by NASA-Glenn Research Center. The tone and broadband components of total noise have been separated from raw test data by using a new data analysis tool. Results in terms of sound pressure levels, acoustic power levels, and their variations with rotor speed, freestream Mach number, and input shaft power, with different blade-pitch setting angles at simulated cruise flight conditions, are presented and discussed. Empirical equations relating models acoustic power level and input shaft power have been developed. The near-field acoustic efficiency of the model at simulated cruise conditions is also determined. It is hoped that the results presented in this work will serve as a database for comparison and improvement of other open rotor blade designs and also for validating open rotor noise prediction codes.

Broadband↗

NASA NTRS2020

Alaska Transportation & Infrastructure Identifying Permafrost Subsidence Using NASA Earth Observations to Pinpoint Road and Infrastructure Vulnerability in Fairbanks, Alaska

A rapidly warming Arctic has compromised the structural integrity of critical infrastructure through accelerated permafrost thaw and thermokarst development underlying these areas. Infrastructure, including roads, bridges, and airports across the state of Alaska are particularly at risk, as permafrost underlies ~85% of the state. However, monitoring the impacts of permafrost thaw on infrastructure is largely limited to in situ observations and frequently identified after the damage is evident. In order to assist transportation and infrastructure decision-makers in Alaska, this project identified and quantified areas of surface subsidence near critical infrastructure. Seasonal interferograms were created using Sentinel-1 C-band Synthetic Aperture Radar (SAR) and L-band Uninhabited Aerial Vehicle SAR (UAVSAR) data to identify areas experiencing surface deformation. Additionally, Light Detection and Ranging (LiDAR) datasets were used to validate select interferograms created between 2017 and 2019. Validation of subsidence detection across platforms was performed over a 7x8 sq. kilometer field site for 2017. The strongest relationship in spatial deformation is observed between Sentinel-1 and UAVSAR with a residual root mean square error of 20 mm. These results suggest that both UAVSAR and Sentinel-1 platforms are capable of detecting surface subsidence. The higher resolution of UAVSAR is better able to resolve localized subsidence features of less than 80 meters, but is limited by temporal resolution. In conjunction, UAVSAR and Sentinel-1 can provide complementary spatial and temporal resolutions for subsidence analysis in the absence of in situ data.

DEVELOP Tech Paper↗

DOE OSTI2021

Tool-workpiece stick-slip conditions and their effects on torque and heat generation rate in the friction stir welding

Friction stir welding (FSW) has found increased applications in automotive and aerospace industries due to its advantages of solid-state bonding, no fusion and melting, and versatility in various working conditions and material combinations. However, the relationship among processing parameters, material properties, and bonding extent and fidelity remains largely empirical, primarily because of the lack of the mechanistic understanding of the tool-workpiece frictional behavior that affects our subsequent understanding of microstructural evolution and interface bonding formation. While the tool-workpiece stick-slip condition is believed to dictate the resulting torque and heat generation rate during the welding process, it remains rare and elusive to conduct a quantitative experimental measurement of such interfacial field. On the other hand, numerical simulations based on Computational Fluid Dynamics (CFD) rely on ad hoc assumptions of interfacial pressure and shear-stress conditions, but predictions can only be validated via the medium- and far-range temperature field which is known to be insensitive to the interfacial frictional behavior. This work first presents a comparison among two CFD-based simulation methodologies and the Coupled Eulerian Lagrangian (CEL) model in finite element method, the last of which uses the Coulomb friction so that the stick-slip is naturally developed. Based on the Hill-Bower similarity relationship in the contact analysis, an analytical model is developed here to prove why a constant stick-slip fraction will be developed in the steady state, to correlate the stick-slip fraction to processing parameters such as the tool spin rate, and further to derive dimensionless functions for torque and heat-generation-rate predictions. Pros and cons of various numerical approaches in predicting stick-slip are discussed, and our analytical model has been found to agree well with our numerical simulation and literature experimental results. These analyses provide the critical strain-rate and temperature fields that are needed for the bonding analysis in our future work.

36 MATERIALS SCIENCE↗

NASA NTRS2022

Extension and Validation of the Pendulum Model for Longitudinal Solar Prominence Oscillations

Context. Longitudinal oscillations in prominences are common phenomena on the Sun. These oscillations can be used to infer the geometry and intensity of the filament magnetic field. Previous theoretical studies of longitudinal oscillations made two simplifying assumptions: uniform gravity and semicircular dips on the supporting flux tubes. However, the gravity is not uniform and realistic dips are not semicircular. Aims. Our aim is to understand the effects of including the nonuniform solar gravity on longitudinal oscillations and explore the validity of the pendulum model with different flux-tube geometries. Methods. We first derived the equation describing the motion of the plasma along the flux tube including the effects of nonuniform gravity, yielding corrections to the original pendulum model. We also computed the full numerical solutions for the normal modes and compared them with the new pendulum approximation. Results. We find that the nonuniform gravity introduces a significant modification in the pendulum model. We also found a cut-off period; i.e., the longitudinal oscillations cannot have a period longer than 167 min. In addition, considering different tube geometries, the period depends almost exclusively on the radius of curvature at the bottom of the dip. Conclusions. We conclude that nonuniform gravity significantly modifies the pendulum model. These corrections are important for prominence seismology, because the inferred values of the radius of curvature and minimum magnetic-field strength differ substantially from those of the old model. However, we find that the corrected pendulum model is quite robust and is still valid for noncircular dips.

Sun: corona↗

NASA NTRS1995

Verification and Validation of Simulation Models for High-Speed Flow Fields

This paper is largely based on the paper titled "Guide to Credible Computational Fluid Dynamics Simulations (Invited)" (AIAA Paper 95-2225). The significance of computational fluid dynamics (CFD) simulations depends solely on their credibility. A customer of CFD products -- simulations and software -- expects that these products are credible for the intended use. Simulation model verification and validation are critical in establishing the credibility of simulations and in certifying simulation software. The only thing that matters in establishing the credibility is uncertainty, not veracity or validity. The sensitivity-uncertainty analysis is the key to the establishment of this credibility. Assessing the credibility of complex simulation results poses a significant challenge. Terminology, concepts, framework, and guidelines are presented for addressing this challenge. Verification assesses whether the problem is solved correctly and estimates the level of computational accuracy of simulations; validation determines whether the right problem is solved and assesses the level of validity of the simulation model by estimating the degree to which simulations accurately represent reality. These concepts and the related guidelines are discussed with examples from high-speed flow fields.

Mehta, Unmeel B.↗

DOE OSTI2026

Testing of a 15 kA Superconducting Transformer

Here, the manufacturing of superconducting magnets for High Energy Physics (HEP) and Fusion Energy Sciences (FES) applications requires high-current conductors to generate stronger magnetic fields without increasing the inductance of the magnet. Increased inductance is undesirable due to the associated AC losses, which reduce the temperature margin; and the quench protection also becomes complicated. Testing high-current conductors with a direct current (DC) room temperature power supply is unfeasible for two primary reasons: 1) the limited capacity to supply large currents, and 2) the significant heat load losses at the current leads. A superconducting transformer offers a solution to both challenges. A 50-kA superconducting transformer is planned for manufacturing and commissioning at Brookhaven National Laboratory as part of its user facility upgrade. This transformer will facilitate the testing of superconducting cables, conductors, joints, and insert coils under high magnetic field conditions (10 T) and with currents up to 50-kA. To evaluate the manufacturing process and validate the theoretical models, the magnet division has developed and tested a 15-kA prototype transformer. A control loop has been implemented to ensure precise current delivery to the sample. This paper presents the coil design, manufacturing, and experimental results from the cold tests.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2025

Two-frequency RF fields induced multipactor in coaxial transmission lines

This study presents a comprehensive investigation of two-surface multipactor discharge in coaxial transmission lines under two-frequency radio frequency (RF) excitation using one-dimensional Monte Carlo simulations validated against three-dimensional particle-in-cell simulations and experimental data. The results show that introducing a second carrier mode can suppress multipactor by reshaping and shrinking the susceptibility region, with the extent and location of suppression strongly dependent on the device's aspect ratio and the relative phase of the second carrier mode. Distinct suppression patterns are observed across different fd regimes, while in some cases, susceptibility expansion also occurs under two-frequency operation. A key outcome is the identification and delineation of pure and mixed multipactor modes in coaxial geometry, where analytical mode boundaries are not readily available. Unlike planar geometries, pure-mode regions in coaxial systems overlap with mixed-mode domains, complicating mode identification. Additionally, image charge forces are found to have negligible influence on susceptibility thresholds but strongly affect electron growth rates. These findings offer valuable insights into the use of waveform engineering for controlling multipactor in high-power RF systems.

43 PARTICLE ACCELERATORS↗

NASA NTRS1989

Results from the Earth Radiation Budget Experiment (ERBE)

The Earth Radiation Budget Experiment (ERBE) has been observing the earth during the past 4 years from three satellites. Numerous validation procedures have been applied to the data. Particularly important have been intercomparisons between three channels of scanning radiometers and wide and medium field-of-view radiometers. These intercomparisons and onboard calibration targets have provided assurance of high data quality. In addition to the classic radiation budget parameters: global absorbed and emitted energy, ERBE is producing fluxes on scales of 250 km that can significantly increase understanding of the earth's climate. Of particular interest are ERBE measurements of clear-sky albedos and longwave fluxes, which are part of the ERBE data products. Use of data from the precessing ERBE satellite together with data from the sun-synchronous NOAA-9 and NOAA-10 satellites also provides information on the diurnal cycle of shortwave and longwave fluxes.

Barkstrom, Bruce R.↗

NASA NTRS1993

Numerical simulation of rarefied flow through a slit. I - Direct simulation Monte Carlo results

The pressure-driven flow of a rarefied monatomic gas through a two-dimensional slit is simulated using the direct simulation Monte Carlo technique. Of particular interest is the change in flow field structure as pressure ratio and Knudsen number are varied. Comparisons are made to quantify the limits of validity of free-molecular theory and approximate, nearly free-molecular iterative methods. Also addressed is the sensitivity of the numerical solutions to grid structure and boundary conditions. The free-molecular theory is found to predict quantitative flow field properties (e.g., centerline velocities or downstream flux profiles) reasonably well for large finite Knudsen number with the error dependent on the pressure ratio. The nearly free-molecular corrections are shown to have limited range of applicability. A previously derived parameter is found to correlate total mass flux well as a function of pressure ratio and Knudsen number over a large portion of the transitional regime.

Wadsworth, D. C.↗