Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “distributed parallelization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Development of a spinning wave heat engine

A theoretical analysis and an experimental investigation were conducted to assess the feasibility of developing a spinning wave heat engine. Such as engine would utilize a large amplitude traveling acoustic wave rotating around a cylindrica chamber, and it should not suffer from the inefficiency, noise, and intermittent thrust which characterizes pulse jet engines. The objective of this investigation was to determine whether an artificially driven large amplitude spinning transverse wave could induce a steady flow of air through the combustion chamber under cold flow conditions. In the theoretical analysis the Maslen and Moore perturbation technique was extended to study flat cylinders (pancake geometry) with completely open side walls and a central opening. In the parallel experimental study, a test moel was used to determine resonant frequencies and radial pressure distributions, as well as oscillatory and steady flow velocities at the inner and outer peripheries. The experimental frequency was nearly the same as the theoretical acoustic value for a model of the same outer diameter but without a central hole. Although the theoretical analysis did not predict a steady velocity component, simulaneous measurements of hotwire and microphone responses have shown that the spinning wave pumps a mean flow radially outward through the cavity.

Zinn, B. T.↗

Load distributions in photoeleastic bolted-joint models

An attempt is made to study the stresses in multiple-bolt connectors, focusing on the stress distribution in a two-pin connector, the two pins being in line and in parallel with the direction of the applied load. The photoelastic modeling approach with two-dimensional transmission photoelasticity is used. The joint models and model fringe patterns are discussed, with special attention given to the existence of a photoelastic isotropic point and to the separation of stresses.

Hyer, M. W.↗

Wave scheduling - Decentralized scheduling of task forces in multicomputers

Decentralized operating systems that control large multicomputers need techniques to schedule competing parallel programs called task forces. Wave scheduling is a probabilistic technique that uses a hierarchical distributed virtual machine to schedule task forces by recursively subdividing and issuing wavefront-like commands to processing elements capable of executing individual tasks. Wave scheduling is highly resistant to processing element failures because it uses many distributed schedulers that dynamically assign scheduling responsibilities among themselves. The scheduling technique is trivially extensible as more processing elements join the host multicomputer. A simple model of scheduling cost is used by every scheduler node to distribute scheduling activity and minimize wasted processing capacity by using perceived workload to vary decentralized scheduling rules. At low to moderate levels of network activity, wave scheduling is only slightly less efficient than a central scheduler in its ability to direct processing elements to accomplish useful work.

Van Tilborg, A. M.↗

A cyclotron-maser instability associated with a nongyrotropic distribution

A stability analysis for the cyclotron-maser instability in the presence of a nongyrotropic electron distribution is presented. The model configuration describes a uniformly magnetized cold ambient plasma that contains a relatively diffuse suprathermal electron component coherently bunched in gyrophase. The stability of perturbations propagating parallel to the ambient magnetic field is considered, and substantial growth rates are found to occur. The results are contrasted with those found for a comparable gyrotropic loss-cone distribution, and it is found that the nongyrotropic instability is characterized by substantially higher growth rates.

Freund, H. P.↗

Mesh-matrix analysis method for electromagnetic launchers

The mesh-matrix method is a procedure for calculating the current distribution in the conductors of electromagnetic launchers with coil or flat-plate geometry. Once the current distribution is known the launcher performance can be calculated. The method divides the conductors into parallel current paths, or meshes, and finds the current in each mesh by matrix inversion. The author presents procedures for writing equations for the current and voltage relations for a few meshes to serve as a pattern for writing the computer code. An available subroutine package provides routines for field and flux coefficients and equation solution.

Elliott, David G.↗

Control of multiple resonant power processors in a multi-source system

Analysis and test results show that phasor-regulated, Mapham-derived resonant inverters can be paralleled to provide standardizing interfaces for multiple sources on a utility-type, aerospace power distribution bus. The basic sources do not require matching in any way, and may have grossly different characteristics. Fully stable system architectures with multiple sources, parallel/redundant distribution buses, and a wide variety of loads can be easily constructed and controlled. The commands and parameters available for system control allow for tight tolerance bus voltage control, and absolute power-sharing control from the various sources over the full range of possible source and load variations. That level of control enables simplified load power processing hardware and the distribution of losses to optimally load the source thermal control system. Positive control of all system performance and allocation of losses are not required by all missions or vehicles, and overall vehicle considerations do not always require the loads on vehicle energy sources and thermal control systems to be balanced. In those cases, power system control can be simplified, and a hierarchical set of defaults can be substituted for computer-generated or supervisory input commands to allow for stable, fully autonomous system operation.

Mildice, James↗

Cosmos-1989 immunology studies

Evidence from both human and rodent studies has indicated that alterations in immunological parameters occur after space flight. The number of flight experiments has been small, and the full breadth of immunological alterations occurring after space flight remains to be established. Among the major effects on immune responses after space flight that have been reported are: alterations in lymphocyte blastogenesis and natural killer cell activity, alterations in production of cytokines, changes in leukocyte sub-population distribution, and decreases in the ability in the ability of bone marrow cells to respond to colony stimulating factors. Changes have been reported in immunological parameters of both humans and rodents. The significance of these alterations in relation to resistance to infection remains to be established. The current study involved a determination of the effects of flight on Cosmos mission 2044 on leukocyte subset distribution and the sensitivity of bone marrow cells to colony stimulating factor-GM. A parallel study with antiorthostatic suspension was also carried out. The study involved repetition and expansion of studies carried out on Cosmos 1887.

Sonnenfeld, Gerald↗

Semikinetic modeling of the outflow of ionospheric plasma through the topside collisional to collisionless transition region

A collisional semikinetic model is applied to the study of the topside ionosphere transition region. The paper considers the transition from (1) O(+) to H(+) dominance; (2) subsonic to supersonic H(+) flow; and (3) collisional to collisionless plasma. The H(+) ions flow upward from a relatively low altitude of 500-1000 km to a high altitude of 7000 km. These ions are subjected to collisions with O(+) ions and self collisions, as well as the effects of macroscopic forces such as the magnetic mirror force, gravity, and the ambipolar electric force. When supersonic outflow occurs, the H(+) velocity-distribution function shows a large departure from Maxwellian with a large positive and then negative heat flow, particularly in the region where the flow Mach number passes through one. In cases where subsonic outflow occurs and the H(+) density is relatively low, distribution functions with two peaks can occur. In these situations the H(+) ions have large parallel temperatures and large heat flows when the two peaks are of unequal height.

Wilson, G. R.↗

Average motion, structure and orientation of the distant magnetotail determined from remote sensing of the edge of the plasma sheet boundary layer with E greater than 35 keV ions

We study gradients of the energetic ion intesity observed at the edge of the plasma sheet boundary layer (PSBL) by the energetic ion anisotropy spectrometer (EPAS) on International Sun Earth Explorer 3 (ISEE 3). In particular, we have determined the velocity of the boundary relative to the spacecraft in the direction perpendicular to the tail axis and the angle which the boundary normal makes to the spacecraft spin axis for 1160 PSBL encounters at X(sub GSM) greater than -240 R(sub E). By asuming that, on average, the edge of the PSBL is parallel to the cross-tail current sheet, we are then able to determine a number of properties of the structure, orientation and motion of the deep geomagnetic tail. We conclude the following: (1) Most crossings of the edge of the PSBL are caused by transverse motuion of the entire tail induced by solar wind direction variations, although some are caused by reconfiguration of the tail due to geomagnetic activity. (2) The typical velocity of the PSBL (and hence of the tail) in the direction perpendicular to the tail axis is 50-85 km/s. (3) The average twist of the tail is near zero, with the edge of the PSBL (and by inference the cross-tail current sheet) lying parallel to the ecliptic plane (however, large twists are found in individual events and the distribution of twists is broad, with one standard deviation of approximately 50 deg. (4) The width of the distribution decreases with downtail distance. (5) The variation of the distributions with cross-tail position reveals that this decreas in width is most likely due to the edge of the PSBL being concave, or significantly flared at the tail flanks, in the near-Earth region. (6) During days on which the Interplanetary Magnetic Field (IMF) has 'away' sector structure, the north lobe of the trail is twisted on average towards dawn by 7.0 +/-2.4 deg. (7) During days on which the IMF has 'toward' sector structure, the north lobe is tilted towards duskby 3.8 +/- 2.3. (8) A subset of events for which IMP 8 solar wind data are available show that, for southward IMF BH(sub z) the tail has a mean twist of -12.3 +/- 5.0 deg for IMF B(sub Y) greater than 0 and 5.5 +/- 3.8 deg for IMF B(sub Y) less than 0 (positive twist angles correspond to a tilt of the northern lobe towards dusk). (9) For northward IMF B(sub z) the tail has a twist of -23.9 +/- 5.0 deg for IMF B(sub Y) greater than 0 and 13.4 +/- 6.0 deg for IMF B(sub y) less than 0. Hence the tail appears more twisted on average for the IMF B(sub Z) northward case. (10) The distribution of tail twist is wider for lower levels of geomagnetic activity, indicating that the tail is able to twist more at lower levels of activity. (11) The data set reveals no evident effect of the earth's dipole wobble; tail orientation appears to be controlled by the solar wind and IMF, such that the GSE coordinate system may be appropriate for the study of field and plasma structures in the distant tail region.

Owen, C. J.↗

Equilibrium Slab Models of Lyman-Alpha Clouds

We model the L(sub y(alpha)) clouds as slabs of hydrogen with an ionizing extragalactic radiation field incident from both sides. In general, the equilibrium configuration of a slab at redshift z approx. less than 5 is determined by a balance of the gas pressure, gravity (including the effects of a dark matter halo), and the pressure exerted by the inter-galactic medium, P(sub ext). These models have been used to make predictions of the number of slabs as a function of the neutral hydrogen column density, N(sub H). A break in the curve is predicted at the transition between regimes where gravity and pressure are the dominant confining forces, with a less rapid decrease at larger N(sub H). The transition from optically thin to optically thick slabs leads to a gap in the distribution, whose location is governed largely by the spectrum of ionizing radiation. There are certain parallels between lines of sight through the outer HI disk of spiral galaxy with increasing radius, and the progression from damped, to Lyman limit, to forest clouds. We discuss briefly the possibility that at least some of the observed low z forest clouds may be a separate population, associated with galaxies, as suggested by the observations of Bahcall et al. This population could dominate the forest at present if the dark matter attached to galaxies should lead to gravity confinement for this disk population, while the isolated clouds remain pressure confined. The formalism developed in this paper will allow a more detailed study. We also discuss a more general parameter study of the equilibrium configuration of slabs, including mock gravity and L(sub y(alpha)) photon trapping.

Charlton, Jane C.↗

Parallel performance investigations of an unstructured mesh Navier-Stokes solver

A Reynolds-averaged Navier-Stokes solver based on unstructured mesh techniques for analysis of high-lift configurations is described. The method makes use of an agglomeration multigrid solver for convergence acceleration. Implicit line-smoothing is employed to relieve the stiffness associated with highly stretched meshes. A GMRES technique is also implemented to speed convergence at the expense of additional memory usage. The solver is cache efficient and fully vectorizable, and is parallelized using a two-level hybrid MPI-OpenMP implementation suitable for shared and/or distributed memory architectures, as well as clusters of shared memory machines. Convergence and scalability results are illustrated for various high-lift cases.

Mavriplis, Dimitri J.↗

Communication Studies of DMP and SMP Machines

Understanding the interplay between machines and problems is key to obtaining high performance on parallel machines. This paper investigates the interplay between programming paradigms and communication capabilities of parallel machines. In particular, we explicate the communication capabilities of the IBM SP-2 distributed-memory multiprocessor and the SGI PowerCHALLENGEarray symmetric multiprocessor. Two benchmark problems of bitonic sorting and Fast Fourier Transform are selected for experiments. Communication-efficient algorithms are developed to exploit the overlapping capabilities of the machines. Programs are written in Message-Passing Interface for portability and identical codes are used for both machines. Various data sizes and message sizes are used to test the machines' communication capabilities. Experimental results indicate that the communication performance of the multiprocessors are consistent with the size of messages. The SP-2 is sensitive to message size but yields a much higher communication overlapping because of the communication co-processor. The PowerCHALLENGEarray is not highly sensitive to message size and yields a low communication overlapping. Bitonic sorting yields lower performance compared to FFT due to a smaller computation-to-communication ratio.

Sohn, Andrew↗

Neurofilament protein defines regional patterns of cortical organization in the macaque monkey visual system: a quantitative immunohistochemical analysis

Visual function in monkeys is subserved at the cortical level by a large number of areas defined by their specific physiological properties and connectivity patterns. For most of these cortical fields, a precise index of their degree of anatomical specialization has not yet been defined, although many regional patterns have been described using Nissl or myelin stains. In the present study, an attempt has been made to elucidate the regional characteristics, and to varying degrees boundaries, of several visual cortical areas in the macaque monkey using an antibody to neurofilament protein (SMI32). This antibody labels a subset of pyramidal neurons with highly specific regional and laminar distribution patterns in the cerebral cortex. Based on the staining patterns and regional quantitative analysis, as many as 28 cortical fields were reliably identified. Each field had a homogeneous distribution of labeled neurons, except area V1, where increases in layer IVB cell and in Meynert cell counts paralleled the increase in the degree of eccentricity in the visual field representation. Within the occipitotemporal pathway, areas V3 and V4 and fields in the inferior temporal cortex were characterized by a distinct population of neurofilament-rich neurons in layers II-IIIa, whereas areas located in the parietal cortex and part of the occipitoparietal pathway had a consistent population of large labeled neurons in layer Va. The mediotemporal areas MT and MST displayed a distinct population of densely labeled neurons in layer VI. Quantitative analysis of the laminar distribution of the labeled neurons demonstrated that the visual cortical areas could be grouped in four hierarchical levels based on the ratio of neuron counts between infragranular and supragranular layers, with the first (areas V1, V2, V3, and V3A) and third (temporal and parietal regions) levels characterized by low ratios and the second (areas MT, MST, and V4) and fourth (frontal regions) levels characterized by high to very high ratios. Such density trends may correspond to differential representation of corticocortically (and corticosubcortically) projecting neurons at several functional steps in the integration of the visual stimuli. In this context, it is possible that neurofilament protein is crucial for the unique capacity of certain subsets of neurons to perform the highly precise mapping functions of the monkey visual system.

Non-NASA Center↗

Assessing the Ability of Instantaneous Aircraft and Sonde Measurements to Characterize Climatological Means and Long-Term Trends in Tropospheric Composition

Over four decades of measurements exist that sample the 3-D composition of reactive trace gases in the troposphere from approximately weekly ozone sondes, instrumentation on civil aircraft, and individual comprehensive aircraft field campaigns. An obstacle to using these data to evaluate coupled chemistry-climate models (CCMs)the models used to project future changes in atmospheric composition and climateis that exact space-time matching between model fields and observations cannot be done, as CCMs generate their own meteorology. Evaluation typically involves averaging over large spatiotemporal regions, which may not reflect a true average due to limited or biased sampling. This averaging approach generally loses information regarding specific processes. Here we aim to identify where discrete sampling may be indicative of long-term mean conditions, using the GEOS-Chem global chemical-transport model (CTM) driven by the MERRA reanalysis to reflect historical meteorology from 2003 to 2012 at 2o by 2.5o resolution. The model has been sampled at the time and location of every ozone sonde profile available from the Would Ozone and Ultraviolet Radiation Data Centre (WOUDC), along the flight tracks of the IAGOSMOZAICCARABIC civil aircraft campaigns, as well as those from over 20 individual field campaigns performed by NASA, NOAA, DOE, NSF, NERC (UK), and DLR (Germany) during the simulation period. Focusing on ozone, carbon monoxide and reactive nitrogen species, we assess where aggregates of the in situ data are representative of the decadal mean vertical, spatial and temporal distributions that would be appropriate for evaluating CCMs. Next, we identically sample a series of parallel sensitivity simulations in which individual emission sources (e.g., lightning, biogenic VOCs, wildfires, US anthropogenic) have been removed one by one, to assess where and when the aggregated observations may offer constraints on these processes within CCMs. Lastly, we show results of an additional 31-year simulation from 1980-2010 of GEOS-Chem driven by the MACCity emissions inventory and MERRA reanalysis at 4o by 5o. We sample the model at every WOUDC sonde and flight track from MOZAIC and NASA field campaigns to evaluate which aggregate observations are statistically reflective of long-term trends over the period.

Atmospheric composition↗

Jet array impingement flow distributions and heat transfer characteristics. Effects of initial crossflow and nonuniform array geometry

Two-dimensional arrays of circular air jets impinging on a heat transfer surface parallel to the jet orifice plate are considered. The jet flow, after impingement, is constrained to exit in a single direction along the channel formed by the jet orifice plate and the heat transfer surface. The configurations considered are intended to model those of interest in current and contemplated gas turbine airfoil midchord cooling applications. The effects of an initial crossflow which approaches the array through an upstream extension of the channel are considered. Flow distributions as well as heat transfer coefficients and adiabatic wall temperatures resolved to one streamwise hole spacing were measured as a function of the initial crossflow rate and temperature relative to the jet flow rate and temperature. Both Nusselt number profiles and dimensionless adiabatic wall temperature (effectiveness) profiles are presented and discussed. Special test results which show a significant reduction of jet orifice discharge coefficients owing to the effect of a confined crossflow are also presented, along with a flow distribution model which incorporates those effects. A nonuniform array flow distribution model is developed and validated.

Florschuetz, L. W.↗

Investigation of air stream from combustor-liner air entry holes, 3

Jets flowing from air entry holes of the combustor liner of a gas turbine were investigated. Cold air was supplied through the air entry holes into the primary hot gas flows. The mass flow of the primary hot gas and issuing jets was measured, and the behavior of the air jets was studied by the measurement of the temperature distribution of the gas mixture. The air jets flowing from three circular air entry holes, single streamwise long holes, and two opposing circular holes, parallel to the primary flow were studied along with the effects of jet and gas stream velocities, and of gas temperature. The discharge coefficient, the maximum penetration of the jets, the jet flow path, the mixing of the jets, and temperature distribution across the jets were investigated. Empirical expressions which describe the characteristics of the jets under the conditions of the experiments were formulated.

Aiba, T.↗

Multiple curved descending approaches and the air traffic control problem

A terminal area air traffic control simulation was designed to study ways of accommodating increased air traffic density. The concepts that were investigated assumed the availability of the microwave landing system and data link and included: (1) multiple curved descending final approaches; (2) parallel runways certified for independent and simultaneous operation under IFR conditions; (3) closer spacing between successive aircraft; and (4) a distributed management system between the air and ground. Three groups each consisting of three pilots and two air traffic controllers flew a combined total of 350 approaches. Piloted simulators were supplied with computer generated traffic situation displays and flight instruments. The controllers were supplied with a terminal area map and digital status information. Pilots and controllers also reported that the distributed management procedure was somewhat more safe and orderly than the centralized management procedure. Flying precision increased as the amount of turn required to intersect the outer mark decreased. Pilots reported that they preferred the alternative of multiple curved descending approaches with wider spacing between aircraft to closer spacing on single, straight in finals while controllers preferred the latter option. Both pilots and controllers felt that parallel runways are an acceptable way to accommodate increased traffic density safely and expeditiously.

Hart, S. G.↗

Electron Energization and Mixing Observed by MMS in the Vicinity of an Electron Diffusion Region During Magnetopause Reconnection

Measurements from the Magnetospheric Multiscale (MMS) mission are reported to show distinct features of electron energization and mixing in the diffusion region of the terrestrial magnetopause reconnection. At the ion jet and magnetic field reversals, distribution functions exhibiting signatures of accelerated meandering electrons are observed at an electron out-of-plane flow peak. The meandering signatures manifested as triangular and crescent structures are established features of the electron diffusion region (EDR). Effects of meandering electrons on the electric field normal to the reconnection layer are detected. Parallel acceleration and mixing of the inflowing electrons with exhaust electrons shape the exhaust flow pattern. In the EDR vicinity, the measured distribution functions indicate that locally, the electron energization and mixing physics is captured by two-dimensional reconnection, yet to account for the simultaneous four-point measurements, translational invariant in the third dimension must be violated on the ion-skin-depth scale.

Chen, Li-Jen↗