SEARCH · Engineering Papers

Results for “distributed generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Cost-effective, Thin-film SOFCs for Reliable Power Generation (Final Report)

The project was aimed at developing and demonstrating an advanced solid-oxide fuel cell (SOFC) technology to cost-effectively and reliably generate electricity directly from hydrocarbon fuels (e.g., natural gas and coal-derived syngas) for distributed and central generation applications. The studied technology was built on a planar, porous metal-supported SOFC (MS-SOFC) with a unique thin-film structure having its anode intimately supported on a metal substrate. The porous metal support with graded porosity was fabricated from a low-cost scalable phase-inversion tape casting method. Anode, thin-film electrolyte, and cathode were sequentially deposited on the porous metal substrate using atmospheric plasma spray (APS). In this study, it was shown that the composition of the casting slurry could significantly influence the morphology of the metal support fabricated using the phase-inversion tape-casting method. Increasing the solid loading in the slurry favored the formation and growth of finger-like pores to a point, but the presence of excessive solid loading increased the viscosity of the casting slurry, restraining the growth of finger-like pores. With the increase in the amount of the binder polyethersulfone (PESf) in the slurry, well grown finger-like pores and a thin sponge-like layer were formed. Since the parameters of the APS process have a significant effect on the microstructure of coatings, which in turn affects or determines the SOFC cell performance, a series of metal-supported solid oxide fuel cells with a four-layer cell configuration of 430L/Ni-ScSZ/ScSZ/LSCF have been fabricated by a combination of phase inversion tape casting and APS techniques. Electrochemical testing of the cells fabricated from different deposition APS conditions revealed significant differences in cell performance.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS1996

Solar Dynamic Power System Stability Analysis and Control

The objective of this research is to conduct dynamic analysis, control design, and control performance test of solar power system. Solar power system consists of generation system and distribution network system. A bench mark system is used in this research, which includes a generator with excitation system and governor, an ac/dc converter, six DDCU's and forty-eight loads. A detailed model is used for modeling generator. Excitation system is represented by a third order model. DDCU is represented by a seventh order system. The load is modeled by the combination of constant power and constant impedance. Eigen-analysis and eigen-sensitivity analysis are used for system dynamic analysis. The effects of excitation system, governor, ac/dc converter control, and the type of load on system stability are discussed. In order to improve system transient stability, nonlinear ac/dc converter control is introduced. The direct linearization method is used for control design. The dynamic analysis results show that these controls affect system stability in different ways. The parameter coordination of controllers are recommended based on the dynamic analysis. It is concluded from the present studies that system stability is improved by the coordination of control parameters and the nonlinear ac/dc converter control stabilize system oscillation caused by the load change and system fault efficiently.

Momoh, James A.↗

DOE OSTI2026

Technical Assistance for Guam Power Authority

Through the Energy Technology Innovation Partnership Project (ETIPP), Guam Power Authority learned approaches to evaluate existing infrastructure to maximize distributed local energy generation without damaging existing system components.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2026

Proposed Algorithm for Placement and Sizing of Generation and Storage Stations in Urban Environments

The placement of generation and storage stations (GSSs) in distribution grids has been extensively investigated. Most traditional methods are applicable to rural or homogeneous environments and do not account for external restrictions on generation placement in urban or semi-urban environments. In this article, we propose a method for generation placement considering externality constraints. New utility-scale generation in distribution grids potentially occupies footprint and interferes in areas with existing infrastructure with architectural, historical, or touristic value. Urban environments are often regulated by municipal legislation. The placement of utility-scale generation in urban landscapes is economically and physically restricted by such externalities, and existing methods for generation placement in distribution grids based on technical optimization fail to account for this important nuance. The proposed algorithm flexibly adapts to changes in government energy policies and priorities. The selection of the type of generation suitable for the power grid is left to the preference of external high-level stakeholders, such as urban planners, industry development leaders, and energy policymakers. The proposed algorithm is a unique tool for determining the placement and sizing of generation in realistic conditions in distribution grids; it is adaptable to urban externalities and sensitive to stakeholder preferences.

generation and storage station placement↗

NASA NTRS1971

Opacity probability distribution functions for electronic systems of CN and C2 molecules including their stellar isotopic forms.

The basis and techniques are presented for generating opacity probability distribution functions for the CN molecule (red and violet systems) and the C2 molecule (Swan, Phillips, Ballik-Ramsay systems), two of the more important diatomic molecules in the spectra of carbon stars, with a view to including these distribution functions in equilibrium model atmosphere calculations. Comparisons to the CO molecule are also shown. T he computation of the monochromatic absorption coefficient uses the most recent molecular data with revision of the oscillator strengths for some of the band systems. The total molecular stellar mass absorption coefficient is established through fifteen equations of molecular dissociation equilibrium to relate the distribution functions to each other on a per gram of stellar material basis.

Querci, F.↗

DOE OSTI2023

Quasi-Distributed Fiber Sensor-Based Approach for Pipeline Health Monitoring: Generating and Analyzing Physics-Based Simulation Datasets for Classification

This study presents a framework for detecting mechanical damage in pipelines, focusing on generating simulated data and sampling to emulate distributed acoustic sensing (DAS) system responses. The workflow transforms simulated ultrasonic guided wave (UGW) responses into DAS or quasi-DAS system responses to create a physically robust dataset for pipeline event classification, including welds, clips, and corrosion defects. This investigation examines the effects of sensing systems and noise on classification performance, emphasizing the importance of selecting the appropriate sensing system for a specific application. The framework shows the robustness of different sensor number deployments to experimentally relevant noise levels, demonstrating its applicability in real-world scenarios where noise is present. Overall, this study contributes to the development of a more reliable and effective method for detecting mechanical damage to pipelines by emphasizing the generation and utilization of simulated DAS system responses for pipeline classification efforts. The results on the effects of sensing systems and noise on classification performance further enhance the robustness and reliability of the framework.

36 MATERIALS SCIENCE↗

DOE OSTI2024

CO 2 storage site characterization using ensemble-based approaches with deep generative models

Estimating spatially distributed properties such as permeability from available sparse measurements is a great challenge in efficient subsurface CO 2 storage operations. In this paper, a deep generative model that can accurately capture complex subsurface structure is tested with an ensemble-based inversion method for accurate and accelerated characterization of CO 2 storage sites. We chose Wasserstein Generative Adversarial Network with Gradient Penalty (WGAN-GP) for its realistic reservoir property representation and Ensemble Smoother with Multiple Data Assimilation (ES-MDA) for its robust data fitting and uncertainty quantification capability. WGAN-GP are trained to generate high-dimensional permeability fields from a low-dimensional latent space and ES-MDA then updates the latent variables by assimilating available measurements. Several subsurface site characterization examples including Gaussian, channelized, and fractured reservoirs are used to evaluate the accuracy and computational efficiency of the proposed method and the main features of the unknown permeability fields are characterized accurately with reliable uncertainty quantification. Furthermore, the estimation performance is compared with a widely-used variational, i.e., optimization-based, inversion approach, and the proposed approach outperforms the variational inversion method in several benchmark cases. We explain such superior performance by visualizing the objective function in the latent space: because of nonlinear and aggressive dimension reduction via generative modeling, the objective function surface becomes extremely complex while the ensemble approximation can smooth out the multi-modal surface during the minimization. This suggests that the ensemble-based approach works well over the variational approach when combined with deep generative models at the cost of forward model runs unless convergence-ensuring modifications are implemented in the variational inversion.

42 ENGINEERING↗

DOE OSTI2023

Non-parametric projections of the net-income distribution for all U.S. states for the Shared Socioeconomic Pathways

Abstract Income distributions are a growing area of interest in the examination of equity impacts brought on by climate change and its responses. Such impacts are especially important at subnational levels, but projections of income distributions at these levels are scarce. Here, we project U.S. state-level income distributions for the Shared Socioeconomic Pathways (SSPs). We apply a non-parametric approach, specifically a recently developed principal components algorithm to generate net income distributions for deciles across 50 U.S. states and the District of Columbia. We produce these projections to 2100 for three SSP scenarios in combination with varying projections of GDP per capita to represent a wide range of possible futures and uncertainties. In the generation of these scenarios, we also generated tax adjusted historical deciles by U.S. states, which we used for validating model performance. Our method thus produces income distributions by decile for each state, reflecting the variability in state income, population, and tax regimes. Our net income projections by decile can be used in both emissions- and impact-related research to understand distributional effects at various income levels and identify economically vulnerable populations.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2021

Extended convex hull-based distributed optimal energy flow of integrated electricity-gas systems

Integrated electricity and gas systems are constructed to facilitate the gas-fired generation, and the distributed operation of these integrated systems have received much attention due to the increased emphasis on data security and privacy between different agencies. This paper proposes an extended convex hull based method to address optimal energy flow problems for the integrated electricity and gas systems in a distributed manner. First, a multi-block electricity-gas system model is constructed by dividing the whole system into N blocks considering both physical and regional differences. This multi-block model is then convexified by replacing the nonconvex gas transmission equation with the extended convex hull-based constraints. The Jacobi-Proximal alternating direction method of multipliers algorithm is adopted to solve the convexified model and minimize its operation cost. Finally, the feasibility of the optimal solution for the convexified model is checked, and a sufficient condition is developed. If the sufficient condition is satisfied, the optimal solution for the original nonconvex problem can be recovered from that for the convexified problem. Simulation results demonstrate that the proposed method is tractable and effective in obtaining feasible optimal solutions for multi-block optimal energy flow problems.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2023

On the impact of tidal generation and energy storage integration in PV-rich electric distribution systems

Deep decarbonization of power system operations requires the maximal utilization of available renewable resources. At distribution-level operations, however, grid operators can face numerous challenges in integrating renewables at scale owing to the inherent intermittence of renewable energy resources. These include phenomena such as voltage fluctuations, which are typically mitigated through control actuators such as on-load tap changers (OLTC) as well as energy storage devices, such as battery energy storage systems (BESS). On the one hand, high intermittence of the available renewable portfolio may require increasingly aggressive control of actuators, thereby accelerating the probability of equipment failure. On the other hand, integrating BESS operations and having a diverse renewable generation portfolio can typically help stagger power/energy flow to mitigate the aforementioned adverse impacts. In this paper, we employ a Bayesian framework for equipment lifetime estimation to understand the impact of including tidal energy resources and BESS in distribution system operations for feeders having substantial distribution photovoltaic generation. Our results indicate that while tidal energy alone may slightly decrease equipment reliability, the adverse impact on reliability is significantly magnified by a generation portfolio consisting of tidal generation and photovoltaic generation. Here, we also study the tidal and photovoltaic hosting capacity problem with and without energy storage systems using equipment reliability as an added constraint. We conclude that energy storage increases the reliability-constrained hosting capacity of the distribution system.

14 SOLAR ENERGY↗

NASA NTRS1981

Large-scale anisotropy of the cosmic microwave background radiation

Inhomogeneities in the large-scale distribution of matter inevitably lead to the generation of large-scale anisotropy in the cosmic background radiation. The dipole, quadrupole, and higher order fluctuations expected in an Einstein-de Sitter cosmological model have been computed. The dipole and quadrupole anisotropies are comparable to the measured values, and impose important constraints on the allowable spectrum of large-scale matter density fluctuations. A significant dipole anisotropy is generated by the matter distribution on scales greater than approximately 100 Mpc. The large-scale anisotropy is insensitive to the ionization history of the universe since decoupling, and cannot easily be reconciled with a galaxy formation theory that is based on primordial adiabatic density fluctuations.

Silk, J.↗

NASA NTRS1988

An integrated and modular digital modeling approach for the space station electrical power system development

An electrical power system for the Space Station was designed, developed and built. This system provides for electrical power generation, conditioning, storage, and distribution. The initial configuration uses photovoltaic power generation. The power system control is based on a hierarchical architecture to support the requirements of automation. In the preliminary design and technology development phase of the program, various modeling techniques and software tools were evaluated for the purpose of meeting the Space Station power system modeling requirements. Rocketdyne and LeRC jointly selected the EASY5 simulation software, developed by Boeing Computer Services, as a system level modeling tool. The application of the selected analytical modeling approach to represent the entire power system is described. Typical results of model predictions are also summarized. The equipment modeled includes solar arrays, dc to ac converters, resonant inverters, battery storage system, alternator, transmission line, switch gear, and system level microprocessor controls. During the advanced development phase of this program, several models were developed using this approach.

Gombos, Frank J.↗

NASA NTRS1988

An integrated and modular digital modeling approach for the Space Station electrical power system development

Gombos, Frank J.↗

NASA NTRS1961

Laminar Heat-Transfer and Pressure Measurements at a Mach Number of 6 on Sharp and Blunt 15 deg Half-Angle Cones at Angles of Attack Up to 90 deg

Two circular conical configurations having 15 deg half-angles were tested in laminar boundary layer at a Mach number of 6 and angles of attack up to 90 deg. One cone had a sharp nose and a fineness ratio of 1.87 and the other had a spherically blunted nose with a bluntness ratio of 0.1428 and a fineness ratio of 1.66. Pressure measurements and schlieren pictures of the flow showed that near-conical flow existed up to an angle of attack of approximately 60 deg. At angles of attack above 70 deg high-pressure areas were present near the base and the bow shock wave was considerably curved. Comparison of the results with simply applied theories showed that on the stagnation line pressures may be predicted by Newtonian theory, and heat transfer by local yawed-cylinder theory based on the yaw angle of the windward generator and the local radius of the cone. Base effects increased the heat transfer in a region extending forward approximately 15 to 30 percent of the windward generator. Circumferential pressure distributions were higher than the corresponding Newtonian distribution and a better prediction was obtained by modifying the theory to match the pressure at 90 deg from the windward generator to that on the surface of the cone at an angle of attack of 0 deg. Circumferential heat-transfer distributions were predicted satisfactorily up to about 60 deg from the stagnation line by using Lees' heat-flux distribution based on the Newtonian pressure. The effects of nose bluntness at large angles of attack were very small in the region beyond two nose radii from the point of tangency.

Conti, Raul J.↗

NASA NTRS2004

Modeling of Optical Waveguide Poling and Thermally Stimulated Discharge (TSD) Charge and Current Densities for Guest/Host Electro Optic Polymers

A charge density and current density model of a waveguide system has been developed to explore the effects of electric field electrode poling. An optical waveguide may be modeled during poling by considering the dielectric charge distribution, polarization charge distribution, and conduction charge generated by the poling field. These charge distributions are the source of poling current densities. The model shows that boundary charge current density and polarization current density are the major source of currents measured during poling and thermally stimulated discharge These charge distributions provide insight into the poling mechanisms and are directly related to E(sub A), and, alpha(sub r). Initial comparisons with experimental data show excellent correlation to the model results.

Watson, Michael D.↗

NASA NTRS1973

Preliminary measurements on heat balance in pneumatic tires

A variety of tests was undertaken to determine the nature of heat generation associated with a pneumatic tire operating under various conditions. Tests were conducted to determine the magnitude and distribution of internally generated heat caused by hysteresis in the rubber and ply fabric in an automobile tire operating under conditions of load, pressure, and velocity representative of normal operating conditions. These included tests at various yaw angles and tests with braking applied. In other tests, temperature sensors were mounted on a road to measure the effect of a tire rolling over and an attempt was made to deduce the magnitude and nature of interfacial friction from the resulting information. In addition, tests were performed using the scratch plate technique to determine the nature of the motion between the tire and road. Finally, a model tire was tested on a roadwheel, the surface covering which could be changed, and an optical pyrometer was used to measure rubber surface temperatures.

Nybakken, G. H.↗

NASA NTRSDate not supplied

Distributed Pressure Sensing for Enabling Self-Aware Autonomous Aerial Vehicles

Autonomous aerial transportation will be a fixture of future robotic societies, simultaneously requiring more stringent safety requirements and fewer resources for characterization than current commercial air transportation. More robust, adaptable, self-state estimation will be necessary to create such autonomous systems. We present a modular, scalable, distributed pressure sensing skin for aerodynamic state estimation of a large, flexible aerostructure. This skin used a network of 22 nodes that performed in-situ computation and communication of data collected from 74 pressure sensors, which were embedded into the skin panels of an ultra-lightweight 14-foot wingspan made from commutable, lattice-based subcomponents, and tested at NASA Langley Research Center's 14X22 wind tunnel. The density of the pressure sensors allowed for the use of a novel distributed algorithm to generate estimates of the wing lift contribution that were more accurate than the direct integration of the pressure distribution over the wing surface.

Daniel Cellucci↗

NASA NTRS2012

Copilot: Monitoring Embedded Systems

Runtime verification (RV) is a natural fit for ultra-critical systems, where correctness is imperative. In ultra-critical systems, even if the software is fault-free, because of the inherent unreliability of commodity hardware and the adversity of operational environments, processing units (and their hosted software) are replicated, and fault-tolerant algorithms are used to compare the outputs. We investigate both software monitoring in distributed fault-tolerant systems, as well as implementing fault-tolerance mechanisms using RV techniques. We describe the Copilot language and compiler, specifically designed for generating monitors for distributed, hard real-time systems. We also describe two case-studies in which we generated Copilot monitors in avionics systems.

Pike, Lee↗