Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composition and microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Developing A Contoured Deposition Head for In-Situ Tape Laying and Fiber Placement

A conformable compaction system employing three individual compactors has been designed for integration into fiber placement and tape laying deposition heads for out-of-autoclave fabrication of thermoplastic contoured parts. The compactors are intended to perform against two geometry specifications: (1) a general minimum radius of curvature limit of 180cm (71-in), and (2) a pad-up specification with a maximum height of 2.5mm (0.1-in) and a minimum ramp of 2.5mm (1-in). The mirrored specification is applicable to a pan-down. The three designs include a hot line compactor capable of a 1000N (400-lb) force at 450C over a 114mm (4.5-in) width, a hot area compactor capable of a 400N (100-lb) force at 450C over a 114mm width by 76mm length (4.5-in by 3-in), and a cold compactor that combines the features of a line and an area compactor. The cold compactor s line segments act with a 2800N (700-lb) force across a 127mm (5-in) width, while the cold compactor's area segments act with a 1000N (250-lb) force over a 127mm by 102mm (5-in by 4-in) area. Two of the designs, the hot line and hot area compactors, have been constructed, developed, and proven out in hot mode to compact actual thermoplastic composite plies over undulating geometry. IM-7PEEK [0/90/0/90]s pan-down and IM-7PEEK [0/-45/90/45]2s pad-up laminates have been fabricated and photomicrographs show good microstructure.

Lamontia, Mark A.↗
NASA NTRS2016

Joining and Integration of Silicon Carbide-Based Materials for High Temperature Applications

Advanced joining and integration technologies of silicon carbide-based ceramics and ceramic matrix composites are enabling for their implementation into wide scale aerospace and ground-based applications. The robust joining and integration technologies allow for large and complex shapes to be fabricated and integrated with the larger system. Potential aerospace applications include lean-direct fuel injectors, thermal actuators, turbine vanes, blades, shrouds, combustor liners and other hot section components. Ground based applications include components for energy and environmental systems. Performance requirements and processing challenges are identified for the successful implementation different joining technologies. An overview will be provided of several joining approaches which have been developed for high temperature applications. In addition, various characterization approaches were pursued to provide an understanding of the processing-microstructure-property relationships. Microstructural analysis of the joint interfaces was conducted using optical, scanning electron, and transmission electron microscopy to identify phases and evaluate the bond quality. Mechanical testing results will be presented along with the need for new standardized test methods. The critical need for tailoring interlayer compositions for optimum joint properties will also be highlighted.

Ceramic Matrix Composites↗
NASA NTRS2002

High-Fidelity Generalization Method of Cells for Inelastic Periodic Multiphase Materials

An extension of a recently-developed linear thermoelastic theory for multiphase periodic materials is presented which admits inelastic behavior of the constituent phases. The extended theory is capable of accurately estimating both the effective inelastic response of a periodic multiphase composite and the local stress and strain fields in the individual phases. The model is presently limited to materials characterized by constituent phases that are continuous in one direction, but arbitrarily distributed within the repeating unit cell which characterizes the material's periodic microstructure. The model's analytical framework is based on the homogenization technique for periodic media, but the method of solution for the local displacement and stress fields borrows concepts previously employed by the authors in constructing the higher-order theory for functionally graded materials, in contrast with the standard finite-element solution method typically used in conjunction with the homogenization technique. The present approach produces a closed-form macroscopic constitutive equation for a periodic multiphase material valid for both uniaxial and multiaxial loading. The model's predictive accuracy in generating both the effective inelastic stress-strain response and the local stress said inelastic strain fields is demonstrated by comparison with the results of an analytical inelastic solution for the axisymmetric and axial shear response of a unidirectional composite based on the concentric cylinder model, and with finite-element results for transverse loading.

Aboudi, Jacob↗
NASA NTRS2003

High Strength Discontinuously Reinforced Aluminum For Rocket Applications

This study presents results on the development of a new aluminum alloy with very high strength and ductility. Five compositions of Al-Mg-Sc-Gd-Zr alloy were selected for this purpose. These alloys were also reinforced with 15 volume percent silicon-carbide and boron-carbide particles to produce Discontinuously Reinforced Aluminum (DRA) materials. Matrix alloys and DRA were processed using a powder metallurgy process. The helium gas atomization produced very fine powder with cellular-dentritic microstructure. The microstructure of matrix alloys showed fine Al3Sc based precipitate which provides significant strengthening in these alloys. DRA showed uniform distribution of reinforcement in aluminum matrix. DRA materials were tested at -320 F, 75 F in air and 7S F in gaseous hydrogen environments and matrix alloys were tested at 75 F in air. DRA showed high strengths in the range of 89-111 ksi (614-697 MPa) depending on alloy compositions and test environments. Matrix alloys had a good combination of strength, 84-89 ksi (579-621 MPa) and ductility, 4.5-6.5%. The properties of these materials can further be improved by proper control of processing parameters.

Pandey, A. B.↗
NASA NTRS1977

Directionally solidified eutectic alloy gamma-beta

A pseudobinary eutectic alloy composition was determined by a previously developed bleed-out technique. The directionally solidified eutectic alloy with a composition of Ni-37.4Fe-10.0Cr-9.6Al (in wt%) had tensile strengths decreasing from 1,090 MPa at room temperature to 54 MPa at 1,100 C. The low density, excellent microstructural stability, and oxidation resistance of the alloy during thermal cycling suggest that it might have applicability as a gas turbine vane alloy while its relatively low high temperature strength precludes its use as a blade alloy. A zirconium addition increased the 750 C strength, and a tungsten addition was ineffective. The gamma=beta eutectic alloys appeared to obey a normal freezing relation.

Tewari, S. N.↗
NASA NTRS1990

The microstructure and properties of rapidly solidified, dispersion-strengthened NiAl

An advanced rapid solidification technology for processing reactive and refractory alloys, utilized to produce large quantities of melt-spun filaments of NiAl, is presented. The melt-spun filaments are pulverized to fine particle sizes, and subsequently consolidated by hot extrusion or hot isostatic pressing. Rapid solidification process gives rise to very fine-grained microstructures. However, exposure to elevated temperature during hot consolidation leads to grain growth. Alloying agents such as borides, carbides, and tungsten can pin the grain boundaries and retard the grain growth. Various alloy compositions are investigated. The eventual goal is to utilize the hot-extruded and forged stock to grow single-crystal NiAl blades for advanced gas-turbine engine applications. Single-crystal NiAl, containing a uniform dispersion of carbide strengthening precipitates, is expected to lead to highly creep-resistant turbine blades, and is of considerable interest to the aerospace propulsion industry.

Jha, S. C.↗
NASA NTRS2006

Multimode-Guided-Wave Ultrasonic Scanning of Materials

Two documents discuss a method of characterizing advanced composite materials by use of multimode-guided ultrasonic waves. A transmitting transducer excites modulated (e.g., pulsed) ultrasonic waves at one location on a surface of a plate specimen. The waves interact with microstructure and flaws as they propagate through the specimen to a receiving transducer at a different location. The received signal is analyzed to determine the total (multimode) ultrasonic response of the specimen and utilize this response to evaluate microstructure and flaws. The analysis is performed by software that extracts parameters of signals in the time and frequency domains. Scanning is effected by using computer-controlled motorized translation stages to position the transducers at specified pairs of locations and repeating the measurement, data-acquisition, and data-analysis processes at the successive locations. One document presents results of a scan of a specimen containing a delamination.

Roth, Don↗
NASA NTRSDate not supplied

Three-dimensional in Situ Observations of Polycrystalline Microstructure Evolution During Directional Solidification of Transparent Alloys Aboard the ISS and Quantitative Comparison with Numerical Modeling

Cellular/dendritic microstructures formed during solidification have a crucial influence on the mechanical properties of a wide range of structural alloys. By minimizing the amount of gravity-induced convection in the liquid, directional solidification experiments using transparent organic alloys conducted in the DECLIC-DSI onboard the International Space Station have provided unique 3D in situ observations of the spatiotemporal evolution of the solid-liquid interface during the formation of cellular and dendritic microstructures under purely diffusive growth conditions in polycrystalline samples containing several grains with a small misorientation with respect to the temperature gradient. Those observations have made it possible to perform benchmark quantitative comparisons with the predictions of state-of-the-art phase-field simulations of microstructure formation in 3D on experimentally relevant length and time scales. This talk will report quantitative comparisons between microgravity experiments and phase-field simulations in succinonitrile-camphor alloys of two different compositions that shed new light on the role of subgrain boundaries in the spatiotemporal evolution of the primary cellular spacing and the selection of dendritic array structures.

Kaihua Ji↗
NASA NTRSDate not supplied

Three-Dimensional In Situ Observations of Polycrystalline Microstructure Evolution During Directional Solidification of Transparent Alloys Aboard the ISS and Quantitative Comparison with Numerical Modeling

Cellular/dendritic microstructures formed during solidification have a crucial influence on the mechanical properties of a wide range of structural alloys. By minimizing the amount of gravity-induced convection in the liquid, directional solidification experiments using transparent organic alloys conducted in the DECLIC-DSI onboard the International Space Station have provided unique 3D in situ observations of the spatiotemporal evolution of the solid-liquid interface during the formation of cellular and dendritic microstructures under purely diffusive growth conditions. Those observations have made it possible to perform benchmark quantitative comparisons with the predictions of state-of-the-art phase-field simulations of microstructure formation in 3D on experimentally relevant length and time scales. This talk will report quantitative comparisons between microgravity experiments and phase-field simulations in succinonitrile-camphor alloys of two different compositions, which shed new light on the selection of dendritic array structures, and on roles of macroscopic curvatures and subgrain boundaries between grains with a small misorientation with respect to the temperature gradient in the spatiotemporal evolution of the primary cellular spacing.

Kaihua Ji↗
NASA NTRS1998

Microstructural, Chemical and Mechanical Characterization of Polymer-Derived Hi-Nicalon Fibers with Surface Coatings

Room temperature tensile strengths of as-received Hi-Nicalon fibers and those having BN/SiC, p-BN/SiC, and p-B(Si)N/SiC surface coatings, deposited by chemical vapor deposition, were measured using an average fiber diameter of 13.5 microns. The Weibull statistical parameters were determined for each fiber. The average tensile strength of uncoated Hi-Nicalon on was 3.19 +/- 0.73 GPa with a Weibull modulus of 5.41. Strength of fibers coated with BN/SiC did not change. However, coat with p-BN/SiC and p-B(Si)N/SiC surface layers showed strength loss of approx. 10 and 35 percent, respectively, compared with as-received fibers. The elemental compositions of the fibers and the coatings were analyzed using scanning Auger microprobe and energy dispersive x-ray spectroscopy. The BN coating was contaminated with a large concentration of carbon and some oxygen. In contrast, p-BN, p-B(Si)N, and SiC coatings did not show any contamination. Microstructural analyses of the fibers and the coatings were done by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and selected area electron diffraction. Hi-Nicalon fiber consists of the P-SIC nanocrystals ranging in size from 1 to 30 nm embedded in an amorphous matrix. TEM analysis of the BN coating revealed four distinct layers with turbostatic structure. The p-BN layer was turbostratic and showed considerable preferred orientation. The p-B(Si)N was glassy and the silicon and boron were uniformly distributed. The silicon carbide coating was polycrystalline with a columnar structure along the growth direction. The p-B(Si)N/SiC coatings were more uniform, less defective and of better quality than the BN/SiC or the p-BN/SiC coatings.

Bansal, Narottam P.↗
NASA NTRS1988

Processing, texture and mechanical properties of sintered silicon carbide

With regard to its favorable properties, in particular those shown at high temperatures, silicon carbide is of great interest for applications related to the construction of engines and turbines. Thus, silicon carbide could replace heat-resisting alloys with the objective to achieve a further increase in operational temperature. The present investigation is concerned with approaches which can provide silicon carbide material with suitable properties for the intended applications, taking into account the relations between characteristics of the raw material, material composition, sinter conditions, and results of the sintering process. The effects of density and texture formation on the mechanical properties are studied. It is found that a dense material with a fine-grained microstructure provides optimal mechanical properties, while any deviation from this ideal condition can lead to a considerable deterioration with respect to the material properties.

Landfermann, H.↗
NASA NTRS2001

Effects of Minor Alloying Additions on the Microstructure, Toughness, and Creep Strength of Directionally Solidified NiAl-31Cr-3Mo

A study of the effects of small (0.25 to 1.0 at%) fifth element additions to the structure and mechanical properties of directionally solidified (DS) NiAl-31Cr-3Mo has been undertaken. Essentially all the additions changed the as-DS'ed microstructure from lamellar eutectic grains to cells and, in some cases, introduced NiAl dendrites and/or third phases. In general the alloying additions did not improve strength or toughness over that possessed by the base composition; only Hf and, perhaps Ti, gave a minor increase in elevated temperature creep resistance. The lack of improvement in creep properties is probably due to inability to precipitation harden NiAl.

Whittenberger, J. D.↗
NASA NTRS2013

Castable Amorphous Metal Mirrors and Mirror Assemblies

A revolutionary way to produce a mirror and mirror assembly is to cast the entire part at once from a metal alloy that combines all of the desired features into the final part: optical smoothness, curvature, flexures, tabs, isogrids, low CTE, and toughness. In this work, it has been demonstrated that castable mirrors are possible using bulk metallic glasses (BMGs, also called amorphous metals) and BMG matrix composites (BMGMCs). These novel alloys have all of the desired mechanical and thermal properties to fabricate an entire mirror assembly without machining, bonding, brazing, welding, or epoxy. BMGs are multi-component metal alloys that have been cooled in such a manner as to avoid crystallization leading to an amorphous (non-crystalline) microstructure. This lack of crystal structure and the fact that these alloys are glasses, leads to a wide assortment of mechanical and thermal properties that are unlike those observed in crystalline metals. Among these are high yield strength, carbide-like hardness, low melting temperatures (making them castable like aluminum), a thermoplastic processing region (for improving smoothness), low stiffness, high strength-to-weight ratios, relatively low CTE, density similar to titanium alloys, high elasticity and ultra-smooth cast parts (as low as 0.2-nm surface roughness has been demonstrated in cast BMGs). BMGMCs are composite alloys that consist of a BMG matrix with crystalline dendrites embedded throughout. BMGMCs are used to overcome the typically brittle failure observed in monolithic BMGs by adding a soft phase that arrests the formation of cracks in the BMG matrix. In some cases, BMGMCs offer superior castability, toughness, and fatigue resistance, if not as good a surface finish as BMGs. This work has demonstrated that BMGs and BMGMCs can be cast into prototype mirrors and mirror assemblies without difficulty.

Hofmann, Douglas C.↗
NASA NTRS2002

Knowledge of Pest Resistance in SiC/BN/SiC Composites Improved

Ceramic-matrix composites (CMC's) consisting of a silicon carbide matrix reinforced with boron-nitride- (BN-) coated silicon carbide (SiC) fibers are strong contenders for commercial and aerospace applications (in particular, the hot sections of high-performance turbine engines in advanced aircraft and generators). They have very good mechanical properties below approximately 600 C and above approximately 1000 C. Between those temperatures, however, the BN coating oxidizes easily, and the oxidation of the SiC matrix is too sluggish to seal off the composite with a protective layer of silica. In that temperature interval, the preferential oxidation of the BN weakens and embrittles the composite. That phenomenon, referred to as "pest" degradation, is the focus of this work, which aims to identify the causes of and remedies for pesting. Previous work established that pesting in Hi-Nicalon (Nippon Carbon Co., Ltd., Japan)/SiC composites was caused by a layer of free carbon that undermined the oxidation resistance of the BN. New work suggests that composites containing a source of carbon are prone to severe pesting and that those that are free of elemental carbon are resistant pesting. Pest resistance was assessed by exposing machined samples for 100 to 150 hr in an atmospheric burner rig at 600 to 1100 C, followed by a tensile fracture test to measure residual mechanical properties and by characterization of the interphase microstructure. Whether the elemental carbon came from intrinsic or extrinsic sources, its presence induced the tensile strength to drop by over 50 percent in the burner rig, with an even more severe loss of fracture strain. A likely mechanism by which burnoff of the carbon layer exposes the BN to accelerated flank attack by ambient oxidants is shown. The BN is replaced with borosilicates that attack the fiber, and ultimately with silica that embrittles the composites by rigidly bonding components. Thus, the study has shown that pesting can be prevented in SiC/BN/SiC, or at least reduced, by simply excluding free carbon. These studies continue, and plans for future work include investigating the role that carbon may play elsewhere in the interphase region.

Thomas-Ogbuji, Linus U.↗
NASA NTRS1980

Quantitative ultrasonic evaluation of engineering properties in metals, composites, and ceramics

Ultrasonic techniques that have demonstrated potential for material characterization are reviewed. These techniques rely on physical acoustic properties of materials and the interaction of elastic stress waves with morphological factors in the ultrasonic regime. The speed of wave propagation and energy loss by interaction with material microstructure and geometrical factors underlie ultrasonic determination of material properties. Two categories of ultrasonic measurements are discussed: those related to material strengths (e.g., elastic moduli, tensile strength, and fracture toughness) and those related to morphology and material conditions that govern strength and performance (e.g., microstructure, void content, residual stress, fatigue damage). It is shown that large-scale industrial application of ultrasonic NDE will depend on advancement in such areas as theory development, instrumentation, system automation, standardization, and coordination with design.

Vary, A.↗
NASA NTRS2018

Sphene Emotional: How Titanite Was Shocked When the Dinosaurs Died

Accessory mineral geochronometers such as zircon, monazite, baddeleyite, and xenotime are increasingly being recognized for their ability to preserve diagnostic microstructural evidence of hypervelocity processes. However, little is known about the response of titanite to shock metamorphism, even though it is a widespread accessory phase and U-Pb geochronometer. Here we report two new mechanical twin modes in titanite within shocked granitoids from the Chicxulub impact structure, Mexico. Titanite grains in the newly acquired International Ocean Discovery Program Site expedition 364 M0077A core preserve multiple sets of polysynthetic twins, most commonly with composition planes (K1), = ~{1̅11}, and shear direction (η1) = <110>, and less commonly with the mode K1 = {130}, η1 = ~<522>. In some grains, {130} deformation bands have formed concurrently with shock twins, indicating dislocation glide with Burgers vector b = [341] can be active at shock conditions. Twinning of titanite in these modes, the presence of planar deformation features in shocked quartz, and lack of diagnostic shock microstructures in zircon in the same samples highlights the utility of titanite as a shock indicator for a shock pressure range between ~12 and ~17 GPa. Given the challenges of identifying ancient impact evidence on Earth and other bodies, microstructural analysis of titanite is here demonstrated to be a new avenue for recognizing impact deformation in materials where other impact evidence may be erased, altered, or did not manifest due to low shock pressure.

Timms, Nicholas E.↗
NASA NTRS1981

Magnetization of small iron-nickel spheres

Magnetic properties of small iron-nickel alloy spheres, having compositions which cover the entire Fe-Ni binary, are presented. The spheres were formed during solidification in free fall following the melting of electropolished wires of appropriate composition. The spheres with Ni not greater than 25% acquired a martensitic thermal remanence while those with Ni not less than 30% acquired a thermoremanent magnetization. A magnetic remanence-composition diagram and a coercive force-composition diagram are constructed. Magnetic hysteresis loops and derived parameters demonstrate the difference between metal-bearing and oxide-bearing natural samples. The magnetic remanence varies as the sphere size in conjunction with the microstructure. These results help to explain why coercive force is generally low, remanent coercive force is generally high, and their ratio (R/C) is always large in fine metal dispersions, such as lunar samples and chondrite meteorites.

Wasilewski, P.↗
NASA NTRS1985

Study of Eutectic Formation

The objectives of this program are to determine the influence of convection on the microstructure of eutectics and to develop a technique for revealing the longitudinal microstructure of the MnBi-Bi eutectic. Both objectives aim at trying to explain the observed influence of space processing on the microstructure of MnBi-Bi. A computer program was developed and used to determine the concentration field in front of a growing lamellar eutectic. From this the deviation of the interfacial concentration from the eutectic composition was calculated as a function of eutectic composition, freezing rate, convection, and lamellar spacing.

Wilcox, W. R.↗