Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “average atom”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Revealing Structural Evolution of Single Atom Catalysts during Electrochemical CO 2 Reduction by in Situ X-ray Absorption Spectroscopy

Investigating the structural variation of single-atom catalysts (SACs) is crucial to reveal the reaction mechanism under working conditions. Different in situ techniques, especially X-ray absorption spectroscopy (XAS), have been reported to study the structural changes in active sites. However, a systematic study of the relationship between the coordination environment and the catalytic ability of different kinds of SACs is still lacking. Herein, we established isolated transition metal atoms (Fe, Co, Ni, Cu) on N-doped carbon (M-N-C) and employed them in electrocatalytic CO 2 reduction reaction (CO 2 RR). Significantly, Ni-N-C exhibits the highest selectivity (similar to 97.9%) toward CO at -0.8 V vs RHE. In situ XAS characterization discloses the coordination number dependent catalytic performance. Further, the decreased average coordination number of Ni in Ni-N-C at the voltage point with maximum Faradaic efficiency was observed. Density functional theory further provides the possible mechanism of CO 2 -to-CO over the undercoordinated Ni-N-C structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Erosion of tungsten marker layers in W7-X

In order to get first insight into net tungsten erosion in W7-X, tungsten (W) marker layers were exposed during the operational phase OP 1.2b at one position of the Test Divertor Unit (TDU), at 21 different positions of the inner heat shield, and at two scraper elements. The maximum tungsten erosion rate at the TDU strike line was 0.13 nm s -1 averaged over the whole campaign. The erosion was inhomogeneous on a microscopic scale, with higher erosion on ridges of the rough surface inclined towards the plasma and deposition of hydrocarbon layers in the recessed areas of the rough surface. The W erosion at the inner heat shield was below the detection limit of 3–6 × 10 12 W-atoms/cm 2 s, and all inner heat shield tiles were covered with a thin B/C/O layer with thickness in the range 2 × 10 17 –10 18 B + C atoms/cm 2 (about 20–100 nm B + C). W-erosion of the marker layers on the scraper elements was also below the detection limit.

Mayer, M↗
NASA NTRS1992

Definition of the Spatial Resolution of X-Ray Microanalysis in Thin Foils

The spatial resolution of X-ray microanalysis in thin foils is defined in terms of the incident electron beam diameter and the average beam broadening. The beam diameter is defined as the full width tenth maximum of a Gaussian intensity distribution. The spatial resolution is calculated by a convolution of the beam diameter and the average beam broadening. This definition of the spatial resolution can be related simply to experimental measurements of composition profiles across interphase interfaces. Monte Carlo calculations using a high-speed parallel supercomputer show good agreement with this definition of the spatial resolution and calculations based on this definition. The agreement is good over a range of specimen thicknesses and atomic number, but is poor when excessive beam tailing distorts the assumed Gaussian electron intensity distributions. Beam tailing occurs in low-Z materials because of fast secondary electrons and in high-Z materials because of plural scattering.

Williams, D. B.↗
NASA NTRS1993

Distribution and motions of atomic hydrogen in lenticular galaxies. X - The blue S0 galaxy NGC 5102

Results of the mapping of the blue gas-rich S0 galaxy NGC 5102 in the 21-cm H I line with a spatial resolution of 34 x 37 arcsec (delta(alpha) x Delta(delta)) and a velocity resolution of 12 km/s are presented. The H I distribution has a pronounced central depression of 1.9 kpc radius, and most of the H I is concentrated in a 3.6 kpc wide ring with an average radius of 3.7 kpc, assuming a distance of 4 Mpc for NGC 5102. The maximum azimuthally averaged H I surface density in the ring is 1.4 solar mass/sq pc, comparable to that found in other S0 galaxies. The HI velocity field is quite regular, showing no evidence for large-scale deviations from circular rotation, and the H I is found to rotate in the plane of the stellar disk. Both the H I mass/blue luminosity ratio and the radial H I distribution are similar to those in early-type spirals. The H I may be an old disk or it may have been acquired through capture of a gas-rich smaller galaxy. The recent starburst in the nuclear region, which gave the galaxy its blue color, may have been caused by partial radial collapse of the gas disk, or by infall of a gas-rich dwarf galaxy.

Van Woerden, H.↗
DOE OSTI2024

Phase transformation mechanism in irradiation-induced superlattice formation

Atomic kinetic Monte Carlo simulations were used to model void superlattice formation under irradiation in molybdenum, driven by anisotropic diffusion of self-interstitial atoms. A change in the phase transformation mechanism from nucleation and growth to spinodal decomposition occurred with increasing dose rate, with both mechanisms leading to superlattice formation. Analysis of a rate-theory based analytical model showed that an observed change in the kinetics of vacancy accumulation, the appearance of a region of positive second derivative in the plot of average vacancy concentration versus time, was caused by the onset of spinodal instability. Further, the analytical model showed that for molybdenum and several other metals where void superlattice formation is commonly observed, the phase transformation likely occurs by nucleation and growth. However, nickel may offer the possibility of experimental observation of the transition between phase transformation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural features and deuterium diffusion in lithium penta-aluminate pellets under He + and D + ion irradiation

Lithium (Li) penta-aluminate (LiAl 5 O 8 ) is investigated as a potential tritium (T) breeding material, with a focus on microstructural response to ion irradiation and deuterium (D) diffusion behavior. Under high-fluence ion irradiation (2 x 10 17 (He + +D + )/cm 2 ) at 773 K, LiAl 5 O 8 exhibits significant disorder on the Li sublattice, as revealed by atomic-resolution scanning transmission electron microscopy, while the Al and O sublattices remain stable, demonstrating strong resistance to structural amorphization. Irradiation induces the formation of platelet-shaped antiphase boundaries (APBs), which may serve as effective D trapping sites. Atom probe tomography suggests the presence of 6 LiD clusters in the mass spectra, though definite conclusions regarding APB composition are hindered by signal overlap and limited data statistics. Time-of-flight secondary ion mass spectrometry reveals that D retention approaches to saturation at 3 x 10 17 (He + +D + )/cm 2 . Isothermal and isochronal annealing studies determine an average diffusivity of 1.6 x 10 -13 at 773 K and an effective activation energy of 0.8 ± 0.1 eV for D migration. Compared to γ-LiAlO 2 , LiAl 5 O 8 demonstrates superior irradiation resistance, minimal Li loss, and enhanced D retention, underscoring its potential as a durable breeder material for T production. In conclusion, these findings provide key insights into the microstructural evolution, defect dynamics, and D retention mechanisms in LiAl 5 O 8 under reactor-relevant conditions.

42 ENGINEERING↗
DOE OSTI2021

CO 2 Hydrogenation on ZrO 2 /Cu(111) Surfaces: Production of Methane and Methanol

The conversion and utilization of carbon dioxide is a critical challenge for the control of greenhouse gas pollution and in the production of high value chemicals in C1 chemistry. ZrO 2 /Cu(111) is an inverse oxide/metal catalyst that displays high activity and stability for the hydrogenation of CO 2 into methanol at 500-600 K. At elevated temperatures, ZrO 2 grows on a CuO x /Cu(111) substrate forming islands of 10-12 nm in size and an average height of ~ 3 Å. Reaction with H 2 leads to the removal of the copper oxide producing ZrO 2 /Cu(111) surfaces which are very active for the binding and dissociation of CO 2 into CO and C. After exposing ZrO 2 /Cu(111) to moderate or elevated pressures of a CO 2 /H 2 mixture at 300 K, atomic C and minor amounts of CH x O and CO x are deposited on the catalyst surface. The adsorbed CH x O and CO x disappear upon heating above 400 K. The catalytic tests for CO 2 hydrogenation give CO as the main reaction product and CH 4 and CH 3 OH as secondary products. The relative yields of methane and methanol change with time and track the amount of atomic C deposited on the active ZrO 2 /Cu(111) surface. The formation of methane stops once the catalyst surface is saturated with C. Under steady-state conditions, ZrO 2 /Cu(111) is a much better catalyst for methanol synthesis than ZnO/Cu(111). This trend reflects variations in the size of the oxide islands and in the strength of oxide-metal interactions. The use of an inverse oxide/metal configuration is an important synthetic tool when preparing active, selective, and stable catalysts for CO 2 hydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

The effectiveness of D 2 pellet injection in reducing intra-ELM and inter-ELM tungsten divertor erosion rates in DIII-D during the Metal Rings Campaign

Abstract Edge localized modes (ELMs) in H-mode plasmas erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes D 2 pellet injection on the DIII-D fusion experiment used as an ELM mitigation technique applied during the 2016 tungsten Metal Rings Campaign to reduce W erosion during ELMs. The 400.9 nm photon wavelength line emission intensity of tungsten atoms (WI) filterscope channels and Langmuir probes were used to infer the gross erosion rate of tungsten-coated tiles installed in the divertor of DIII-D. D 2 mass injection rates ranging from 34 to 41 arbitrary units (A.U.) and no D 2 injection resulted in a similar total W erosion rate during ELMs (intra-ELM). On average, results show a 29% increase in the total gross W erosion rate with intermediate mass injection rates (∼13–23 A.U.) compared to the no pellets and the highest injection rate cases. On average, the fast D 2 mass injection rate cases had 15% less erosion in the inter-ELM phase than the case with no pellets. Generally, higher D 2 mass injection rates increased the ELM frequency, and the highest injection rates reduced the average erosion per ELM and fractional carbon impurities at the top of the pedestal by nearly 40% when compared to the no-pellet case. As expected, a higher D 2 pellet injection rate led to a higher plasma density and lower plasma temperature in the divertor. Additionally, an increasing divertor inter-ELM plasma electron density directly correlated to more frequent pellet injection and a decrease in both the average gross intra-ELM W erosion and the total gross intra-ELM W erosion rate. Simulations of intra-ELM erosion using the ‘free-streaming plus recycling model’ (FSRM) underestimate W erosion during pellet injection by about 30% on average. The discrepancies between the experimental measurements and the FSRM intra-ELM W erosion predictions are postulated to be due to C/W material mixing. A simple analytic mixed-material model is presented and results in better agreement with the experimental data. These results highlight the importance of incorporating the effects of a mixed-material layer in the analysis of PFC erosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1977

Rotational excitation of linear molecules by collisions with atoms - Comparison of classical and quantum methods

Exact quantum results for the rotational excitation of rigid linear molecules by collisions with atoms are compared with classical trajectory results. The systems studied are CO-He, CS-H2, OCS-H2, HCl-He, and HCl-Ar at collision energies up to 500/cm. Total cross sections and state to state rate constants are compared. The classical results are found to be in good agreement with the quantum results on the average. Differences arising from the existence of purely quantum effects are clearly evident, but consistent and predictable. Two methods of extracting state selective information from moments of the classical distribution are examined and found to be less reliable than the usual histogram method. In conjunction with previous comparisons of classical and quantum results these calculations provide a useful measure of the limitations and reliability of classical trajectories.

Chapman, S.↗
DOE OSTI2019

High temperature neutron diffraction investigation of U 3 Si 2

The U-Si system is actively undergoing studies due to its promise as a component of an accident tolerant nuclear fuel. In this work, the crystal structure of the U 3 Si 2 compound in the U-Si system was investigated as a function of temperature from room temperature to 1298 K for a sample of approximately 42.02 at.% Si composition and 1373 K for a sample with approximately 42.10 at.% Si using high temperature time-of-flight neutron diffraction on the High-Pressure Preferred Orientation (HIPPO) diffractometer at Los Alamos Neutron Science Center (LANSCE). The simultaneous Rietveld refinement of five histograms from the five HIPPO detector backs (40°, 60°, 90°, 120°, and 145°) provided datasets for the lattice parameters, anisotropic atomic displacement parameters, and atomic positions as a function of temperature. To explore the possibility of a homogeneity range, two sample compositions were analyzed, a 40.02 at.% Si (near stoichiometric) and a potentially hyperstoichiometric (40.10 at.% Si) sample. While minor differences in the anisotropic atomic displacement parameters between the two samples were observed, over the entire investigated temperature range no additional phases were found indicative of a single phase sample and the ability of the U 3 Si 2 compound to accommodate nonstoichiometry, suggesting that the U 3 Si 2 compound is not a line compound confirming previous determinations. However, the differences observed in the average coefficient of linear thermal expansion identified between the two compositions warrant future investigation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Manganese-rich high entropy oxides for lithium-ion batteries:materials design approaches to address voltage fade

Lithium- and manganese-rich oxides are of interest as lithium-ion battery cathode materials as Mn is earth abundant, low cost, and can deliver high capacity. Herein, a high entropy strategy was used to prepare Mn rich high entropy oxide (HEO) materials by including four additional metals (Ni, Co, Fe and Al) in the compositions using a mild co-precipitation method. Two HEOs (Li x Ni 0.1 Mn 0.6 Co 0.1 Al 0.1 Fe 0.1 O y , where x = 1.5 for HEO-L and x = 0.5 for HEO-H) with layered and spinel-layered hybrid structures were investigated where the morphology, elemental composition, structure, atomic level phase distribution, and electrochemistry were determined. The HEO-L samples involve a Li 2 TMO 3 layered structure with ~39% stacking faults. HEO-H is a hybrid structure comprised of 80 wt% spinel and 20 wt% LiMO 2 layered structure. The high entropy manganese-rich HEO-L showed higher capacity and 93% retention of the average voltage after 100 cycles while HEO-H showed higher capacity retention and near 100% average voltage retention. Finally, operando X-ray absorption spectroscopy revealed that the Ni, Co, and Mn are redox active in both materials while the Fe center remains at the Fe 3+ oxidation state throughout cycling, where the changes in the oxidation states for both materials during discharge were consistent with the delivered electrochemical capacity rationalizing the observed electrochemistry.

25 ENERGY STORAGE↗
DOE OSTI2024

Interfaces enhanced plasma irradiation resistance in CrMoTaWV/W multilayer films through blocking He diffusion

The performance of plasma-facing materials (PFMs) is one of the key factors that significantly impact the stability of operation in fusion reactors. Herein, a new CrMoTaWV/W (high entropy alloy (HEA)/W) multilayer structure is designed as PFM to investigate its resistance to He plasma irradiation. It was observed that the introduction of the interfaces effectively absorbed plenty of He atoms, preventing them from diffusing into the material and delaying the formation of fuzz incubation zone, therefore, enhancing the resistance to plasma irradiation. The thickness transformed to fuzz in the HEA/W multilayer films was observed to be about two-thirds of those in the CrMoTaWV (HEA) film. Additionally, the fuzz growth rates in HEA/W multilayer films are lower than the average growth rate of bulk W and HEA films combined. These findings highlight a promising new avenue for the exploration of high-performance PFMs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1979

Discovery of soft X-ray flux from 2A 1102+384 = Markarian 421

During April 1976 a soft X-ray flux was detected with SAS 3 from the vicinity of 2A 1102+384. The average flux densities were 4.3 x 10 to the -11th and 14 x 10 to the -11th erg/sq cm per sec in the energy bands 0.1-0.28 keV and 1-6 keV, respectively. There is an indication of variability over about 0.5 day in the lowest energy band. An upper limit of 3 x 10 to the 20th H atoms per sq cm is found for the gas column density to the X-ray source. In May 1978, observations with the modulation collimators of SAS 3 yielded an accurate (40 arcsec error radius) position for the X-ray source (2-6 keV) at right ascension 11 h 1 m 39.7 s, declination + 38 deg 28 min 51 sec (equinox 1950). The earlier tentative identification by Ricketts et al. (1976) with the BL Lacertae object B2 1101+38 = Markarian 421 is thus confirmed.

Hearn, D. R.↗
NASA NTRS2006

Ultrasonication of Bismuth Telluride Nanocrystals Fabricated by Solvothermal Method

The objective of this study is to evaluate the effect of ultrasonication on bismuth telluride nanocrystals prepared by solvothermal method. In this study, a low dimensional nanocrystal of bismuth telluride (Bi2Te3) was synthesized by a solvothermal process in an autoclave at 180 C and 200 psi. During the solvothermal reaction, organic surfactants effectively prevented unwanted aggregation of nanocrystals in a selected solvent while controlling the shape of the nanocrystal. The atomic ratio of bismuth and tellurium was determined by energy dispersive spectroscopy (EDS). The cavitational energy created by the ultrasonic probe was varied by the ultrasonication process time, while power amplitude remained constant. The nanocrystal size and its size distribution were measured by field emission scanning electron microscopy (FESEM) and a dynamic light scattering system. When the ultrasonication time increased, the average size of bismuth telluride nanocrystal gradually increased due to the direct collision of nanocrystals. The polydispersity of the nanocrystals showed a minimum when the ultrasonication was applied for 5 min. Keywords: bismuth telluride, nanocrystal, low-dimensional, ultrasonication, solvothermal

Chu, Sang-Hyon↗
NASA NTRS1978

Performance evaluation of the SAO VLG-11 atomic hydrogen masers

A new generation of frequency standards, the VLG-11 hydrogen maser, has been designed and built at the Smithsonian Astrophysical Observatory (SAO). A comprehensive series of environmental and short-term stability tests on three VLG-11 masers has been completed and evaluated. The test results reported here show substantial improvements over previous hydrogen masers in measured sensitivity to variations in ambient temperature, barometric pressure, and magnetic fields. The maser frequency stability, as represented by the two-sample (Allan) variance, has been measured for averaging times ranging from 1 to 100,00 seconds. The variance is lower than 1 x 10 to the -15th for averaging intervals between 1400 and 20,000 seconds. For times shorter than 4000 seconds, the measured stability data agree remarkably well with theoretical values calculated from thermal noise mechanisms and the 'noise within the linewidth' regime is clearly discernable in the data.

Levine, M. W.↗
DOE OSTI2023

Resolving the Heat Generated from ZrO 2 Atomic Layer Deposition Surface Reactions

Abstract In situ pyroelectric calorimetry and spectroscopic ellipsometry were used to investigate surface reactions in atomic layer deposition (ALD) of zirconium oxide (ZrO 2 ). Calibrated and time‐resolved in situ ALD calorimetry provides new insights into the thermodynamics and kinetics of saturating surface reactions for tetrakis(dimethylamino)zirconium(IV) (TDMAZr) and water. The net ALD reaction heat ranged from 0.197 mJ cm −2 at 76 °C to 0.155 mJ cm −2 at 158 °C, corresponding to an average of 4.0 eV/Zr at all temperatures. A temperature dependence for reaction kinetics was not resolved over the range investigated. The temperature dependence of net reaction heat and distribution among metalorganic and oxygen source exposure is attributed to factors including growth rate, equilibrium surface hydroxylation, and the extent of the reaction. ZrO 2 ‐forming surface reactions were investigated computationally using DFT methods to better understand the influence of surface hydration on reaction thermodynamics.

Bielinski, Ashley R.↗
DOE OSTI2024

Revisiting the influence of Ni particle size on the hydrogenation of CO 2 to CH 4 over Ni/CeO 2

Nickel nanoparticles were supported on CeO 2 and evaluated in the hydrogenation of CO 2 to CH 4 at 538 K and 1 atm. Chemisorption of H 2 was used to estimate the average Ni particle size, which ranged from 1.3 to 17 nm. The apparent activation energy for CH 4 formation and turnover frequency for CO 2 conversion was independent of Ni particle size. The smallest Ni particles (1.3 nm) were less selective to CH 4 . Comparisons to alumina-supported Ni reveal the same performance as Ni/CeO 2 when normalized to active Ni atoms counted by H 2 chemisorption. A beneficial effect of ceria relative to alumina is the enhanced reducibility of Ni as evaluated by H 2 temperature-programmed reduction. The constancy of the turnover frequency on Ni particles suggests the acid-base and/or redox properties of the support do not play a significant role in the CO 2 methanation reaction under the conditions of study, which contrasts many earlier works.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Void swelling of conventional and composition engineered HT9 alloys after high-dose self-ion irradiation

Ferritic/martensitic (F/M) steels are being considered as potential structural materials for next generation nuclear reactors, and variants of the alloy HT9 are some of the most promising candidates. In this study, two conventional and two composition engineered HT9 alloys were irradiated using 3.5 MeV Fe 2+ up to 600 peak displacement-per-atom (dpa) at 450 °C. Void swelling and microstructure evolution were characterized for each alloy and compared. The two conventional HT9 alloys (INL and ACO3) showed similar void swelling behavior due to their similar elemental composition and processing conditions. The INL HT9 exhibited a maximum of 2.4% swelling and the ACO3 HT9 showed a maximum of 2.8% swelling at 342 and 393 average local dpa, respectively. On the other hand, the two-composition engineered HT9 alloys with varying N contents (10 ppm for low N and 440 ppm for high N) showed disparate swelling behavior. The low N HT9 exhibited a maximum of 4.6% swelling, while the high N HT9 showed a maximum of 0.7% swelling at 342 average local dpa. Changes in the N content also affected Ni/Si rich G-phase formation. The low N HT9 showed a larger size and lower density of G-phase precipitates compared with the high N HT9 after 600 peak dpa irradiation. This study compares the void swelling behavior of the ion irradiated four current HT9 alloys to extremely high doses, with the void swelling data from neutron irradiated HT9 alloys. Furthermore, the comparison lends critical insights into how well these current alloys can withstand high neutron fluxes in future reactors, especially since the low N and high N HT9 alloys have never been exposed to such high doses before.

36 MATERIALS SCIENCE↗