Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “analytical model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Analyzing Mechanical integrity of Microwave resonant Cavity flowmeter

The microwave resonant cavity flow sensor has been proposed to address the difficulties of measuring high-temperature molten salt flow in reactor vessels. The flow sensor consists of a metallic cylindrical cavity coupled to a microwave waveguide. The cylindrical cavity has one of the flat surfaces thin enough to undergo microscopic deflection due to dynamic pressure of the exerted by the flowing fluid. Deflection of the membrane causes a shift in the microwave resonant frequency. Fluid velocity can be estimated from the calibration curve. The objective of this report is to investigate mechanical integrity of the flowmeter’s membrane. The membrane is a thin stainless-steel circular plate with a clamped edge, subjected to uniform load. By calculating the stress on the plate due to deflection and, comparing the stress to the material ultimate tensile strength and yield strength, it can be estimated if the plate will fail. If the maximum stress is greater than the yield strength, the plate will undergo plastic deformation, and the sensor will be disabled. A stress greater than the ultimate tensile strength will cause the plate to fracture. The stress on the plate was calculated with an analytic closed form solution model, and with COMSOL Structural Mechanics Module which does not involve any approximations. Stresses in both the analytic model and COMSOL numerical model were calculated for stainless steel 316 thin circular plates under room temperature conditions, where the fluid is water. The diameter of the circular plate is approximately one inch, and thickness is 10mil. Fluid flow velocity is in the range from 0.5m/s to 1m/s. The results from the two models are similar. Both the analytic model and COMSOL model showed that maximum stresses on the plate, which are at the radial boundary of the plate, are three orders of magnitude smaller than the yield strength and ultimate tensile strength. This indicates that the sensor is at a low risk of mechanical failure.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Semi-analytic spectral fitting: simultaneously modelling the mass accumulation and chemical evolution in MaNGA spiral galaxies

We develop a novel semi-analytic spectral fitting approach to quantify the star formation histories (SFHs) and chemical enrichment histories (ChEHs) of individual galaxies. We construct simple yet general chemical evolution models that account for gas inflow and outflow processes as well as star formation, to investigate the evolution of merger-free star-forming systems. These models are fitted directly to galaxies’ absorption-line spectra, while their emission lines are used to constrain current gas phase metallicity and star formation rate. We apply this method to spiral galaxies selected from the SDSS-IV Mapping Nearby Galaxies at Apache Point Observatory survey. By fitting the co-added absorption-line spectra for each galaxy, and using the emission-line constraints on present-day metallicity and star formation, we reconstruct both the SFHs and the ChEHs for all objects in the sample. We can use these reconstructions to obtain archaeological measures of derived correlations such as the mass–metallicity relation at any redshift, which compare favourably with direct observations. We find that both the SFHs and ChEHs have strong mass dependence: massive galaxies accumulate their stellar masses and become enriched earlier. This mass dependence causes the observed flattening of the mass–metallicity relation at lower redshifts. The model also reproduces the observed gas-to-stellar mass ratio and its mass dependence. Moreover, we are able to determine that more massive galaxies have earlier gas infall times and shorter infall time-scales, and that the early chemical enrichment of low-mass galaxies is suppressed by strong outflows, while outflows are not very significant in massive galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Analysis of Cutter Blade Wear in Rotary Shear Mills

Following development of an analytical abrasive wear model to predict wear of components in a rotary shear mill, the team used a finite element analysis (FEA) approach to calculate forces and loads acting on particles responsible for abrasive wear. The analytical model related critical rotary shear process parameters (shear geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness and elastic modulus) that enabled us to model the wear of shear cutters in a rotary shear milling system developed by Forest Concepts. With proper knowledge of the forces acting between abrasive particles and cutter components built into it, the model can accurately predict wear of the cutters and provides a quality by design (QbD) approach to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches. During this reporting period, researchers at Oak Ridge National Laboratory applied an FEA package to simulate the local stresses and forces between an abrasive silica particle and two rotary shear cutters as the distance between the cutters decreases. The output of the FEA was used to provide more accurate projections of the loads applied to the particles in the analytical wear model. Comparison of the FEA force calculations are in good agreement with the loads assumed in the analytical predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

CO 2 zonal injection rate allocation and plume extent evaluation through wellbore temperature analysis

Temperature analysis during a pause in injection operations, known as warmback analysis, has been used in the petroleum industry for evaluating the injection conformance and estimating the location of the flooded front in applications, such as waterflooding oil reservoirs. Here in this work, methods are introduced to extend the application of temperature warmback analysis to estimate the zonal CO 2 injection rate and zonal CO 2 plume extent during geologic CO 2 storage in a saline aquifer. First, novel analytical solutions are developed to model transient temperature in the aquifer during the injection and subsequent shut-in periods considering two-phase flow (gaseous CO 2 and aqueous brine) conditions in the aquifer. The solution involves a discretization of the aquifer into regions; the energy and mass conservation equations for the regions are solved simultaneously considering appropriate boundary conditions at the interfaces. Two solutions techniques are presented: multi-region and three-region solutions. Inverse models are developed accordingly to evaluate the injection profile and estimate the extent of the plume front in the reservoir during the injection period. The multi-region solution results in an inversion approach that requires regression analysis. However, the three-region formulation results in a simple graphical technique for inverse modeling. The analytical solutions are validated against a thermally coupled reservoir simulation tool using different synthetic cases for CO 2 injection in deep saline aquifers. The results of the developed solutions provide a good match with numerical results during forward and inverse modeling.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Towards Realistic and High Fidelity Models for Nuclear Reactor Power Synthesis Simulation with Self-Powered Neutron Detectors

As presented in this report, a weighting function–based inferencing method is being applied to synthesize the power distribution in next-generation and university research reactors based on simulated self power neutron detector (SPND) responses. The overall goal is to assess the impacts of sensor uncertainty and true power distribution perturbations on the error in the synthesized power distribution. Regarding sensor uncertainty, the NuScale Small Modular Reactor (SMR) and the Westinghouse AP1000 serve as testbeds for analyzing the impact of varying the sensor uncertainty, as well as varying the number of sensors per sensor string in the reactor core. The reactor models are informed by Monte Carlo N-Particle (MCNP) neutron flux tallies. For the NuScale SMR and Westinghouse AP1000, the SPND response functions (i.e., the response of the SPNDs to individual segments of fuel) were determined homogeneously. Regarding an analysis of power distribution perturbation detection, the Texas A&M Testing, Research, Isotopes, General Atomics Reactor (TAMU TRIGA) reactor was used as a demonstration case with one particular arrangement of SPNDs; the response functions for this reactor model were determined heterogeneously, making this a uniquely high-fidelity demonstration of perturbation detection. Finally, SPND models generated in the Geometry and Tracking 4 (Geant4) code have been generated and tested for comparison with traditionally implemented analytical SPND models, with the intent for Geant4 integration with the full methodological framework. SPND current outputs as a function of distance from some fuel assembly segment in the NuScale SMR are compared with the analytically determined currents. Results from the sensor uncertainty simulations for the NuScale SMR and AP1000 indicate that the average error in the inferred power distribution on the fuel assembly segment level is reasonably low, being slightly less than the random uncertainty applied to all respective SPNDs in both cores. For example, if all SPNDs in the core have a random uncertainty of 5%, then the corresponding fuel assembly segment level error (i.e. difference between the true and inferred local power) is ~2–3%. However, the maximum error in the inferred power distribution on the fuel assembly segment level can be considerably high (>15%) when SPND random uncertainties start to exceed ~3%. In general, the average and maximum errors in the inferred power distribution were slightly higher in the AP1000 as opposed to the NuScale SMR for the sensor string configurations considered herein. Another result determined from analysis of the sensor uncertainty simulations was that increasing the number of SPNDs per string does not clearly reduce inferred power distribution error and can in fact make the error large in some cases; however, this assessment may skewed due to imposed iteration limits. Results from the perturbation detection demonstration using the high-fidelity TAMU TRIGA model indicate that, given the arrangement of 17 SPND strings and 4 SPNDs per string considered herein, there is a clear, provable ability to infer a localized Gaussian-type peak perturbation in the 3D power distribution. Such a perturbation was detected with an average fuel assembly segment level error of 0.19%, and the general visualization of the detected perturbation clearly indicates that the magnitude and shape were appropriately resolved. Finally, the electrical current output generated by the Geant4 modeled SPND indicates significant magnitude differences than the analytically modeled SPND, demonstrating the need for accurate SPND models which account for finite sensor geometry effects to inform the power synthesis work described herein.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

A Novel Analytical Population Tumor Control Probability Model Includes Cell Density and Volume Variations: Application to Canine Brain Tumor

Tumor control probability (TCP) models based on Poisson statistics characterize the distribution of surviving clonogens. Thus enabling the calculation of TCP for individuals. To mathematically describe clinically observed survival data of patient cohorts it is necessary to extend the Poisson TCP model. This is typically done by either incorporating variations of model parameters or by using an empirical logistic model. The purpose of this work is the development of an analytical population TCP model by mechanistic extension of the Possion model.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2024

An Open-Source Framework for Characterizing Urban Energy Models: Integrating Top-Down and Bottom-Up Methods to Predict Residential Buildings Characteristics: Preprint

Bottom-up urban energy models are crucial for understanding current energy use patterns and informing design strategies. However, accurately characterizing these models to represent different communities remains a challenge due to the extensive data needed for simulating existing energy use behavior. This data includes information related to human activities and building characteristics, all of which correlate with socioeconomic factors. To overcome this challenge, we developed an automated framework that utilizes both top-down and bottom-up data, to predict unknown building and occupant characteristics that are needed for more accurate and equitable modeling and analytics. Our framework, integrated into the URBANopt district energy modeling platform, uses statistical data models from ResStock. URBANopt models co-located buildings and neighborhoods. At this scale there are data gaps in building characteristic data, such as materials, insulation, occupancy, income, and energy usage of the buildings. To address this data gap, we use ResStock data, representative at the census tract scale, and develop machine-learning and deeplearning techniques to disaggregate it to individual buildings. By mapping unique occupant, building and economic properties to URBANopt energy models, we gain detailed insights into the variability of building energy use across different neighborhoods. This insight helps deploy technologies for co-located buildings and supports targeted upgrades for communities with unique economic and demographic characteristics, ensuring energy equity. Accurate characterization of energy models allows us to develop equitable strategies tailored to diverse neighborhoods, whether underserved or affluent. Our automated framework streamlines energy modeling and provides a reliable tool for building energy characterization.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗
DOE OSTI2021

Adsorbate Free Energies from DFT-Derived Translational Energy Landscapes

Adsorption free energies are fundamental to surface chemistry and catalysis. Standard models combine some assumed analytical form of the translational potential energy surface, often parameterized against density functional theory (DFT) calculations, with an analytical expression for the resultant translational densities of states (DOS), free energy, and entropy. Here we compare the performance of such models against numerical evaluations of the DOS and thermodynamic functions derived from solutions to the translational Schrodinger equation. We compare results for a translational potential energy surface (PES) derived from nudged eleastic band calculations with those obtained from adsorbate rastering across a series of monatomic (O, S, C, N, H) and polyatomic (NH x ) adsorbates on (100) Pt and Au facets. We find that analytical models as commonly parameterized have mixed performance for describing the translational PES and that the consequences for computed free energies are modest but potentially significant in microkinetic models. Here, numerical solutions are possible for modest to no additional computational cost over analytical models and thus should be considered when reliable free energy estimates are needed or translational potential energy surfaces are available.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Plasmon coupling in topological insulator multilayers

Topological insulators (TIs) house two-dimensional Dirac plasmons on their surfaces. In TI thin films, plasmons on the top and bottom surfaces couple electrostatically, giving rise to an acoustic and an optical plasmon mode. By extension, a superlattice comprising TI layers and trivially-insulating layers could house multiple complex plasmon modes which could be used to create a new type of Dirac metamaterial. In this paper, we synthesize TI superlattices, fabricate them into stripe arrays, characterize their optical and plasmonic properties, and model the samples using transfer matrices. Furthermore, we excite plasmon modes that couple to the phonons in the superlattice, resulting in hybrid plasmon phonon polaritons. These modes are modeled using an analytical Fano resonance model and the extracted resonant positions are reproduced by transfer matrix modeling. We also excite an epsilon-near-zero mode in the top dielectric material (Bi 0.5 In 0.5 ) 2 Se 3 . Understanding the behavior of the polariton modes in this complex system will lend insight into the many-body interaction in low-dimensional systems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Modeling the Cosmological Lyman-𝛼 Forest at the Field Level

The distribution of absorption lines in the spectra of distant quasars, called the Lyman-𝛼 (Ly-𝛼) forest, is a unique probe of cosmology and the intergalactic medium at high redshifts and small scales. The statistical power of ongoing redshift surveys demands precise theoretical tools to model the Ly-𝛼 forest. We address this challenge by developing an analytic, perturbative forward model to predict the Ly-𝛼 forest at the field level for a given set of cosmological initial conditions. Our model shows a remarkable performance when compared with the Sherwood hydrodynamic simulations: it reproduces the Ly-𝛼 forest flux power spectrum, its cross-correlation with dark matter halos, and the one-point probability distribution function of both fields at the percent level down to scales of a few Mpc. Our work provides crucial tools that bridge analytic modeling on large scales with simulations on small scales, enabling field-level inference from Ly-𝛼 forest data and simulation-based priors for cosmological analyses. Furthermore, this is especially timely for realizing the full scientific potential of the Ly-𝛼 forest measurements by the dark energy spectroscopic instrument.

Cosmological parameters↗
DOE OSTI2023

Analytical Large-Signal Modeling of Inverter-Based Microgrids With Koopman Operator Theory for Autonomous Control

The microgrid (MG) plays a crucial role in the energy transition, but its nonlinearity presents a significant challenge for large-signal power systems studies in the electromagnetic transient (EMT) time scale. In this paper, we develop a large-signal linear MG model that considers the detailed dynamics of the primary and zero-control levels based on the Koopman operator (KO) theory. Firstly, a set of observable functions is carefully designed to capture the nonlinear dynamics of the MG. The corresponding linear KO is then analytically derived based on these observables, resulting in the linear representation of the original nonlinear MG with observables as the new coordinate. The influence of external input on the system dynamics is also considered during the derivation, enabling control of the MG. We solve the voltage control problem using the traditional linear quadratic integrator (LQI) method to demonstrate that textbook linear control techniques can accurately control the original nonlinear MG via the developed KO-linearized MG model. Our proposed KO linearization method is generic and can be easily extended for different control objectives and MG structures using our analytical derivation procedure. Here, we validate the effectiveness of our methodology through various case studies.

25 ENERGY STORAGE↗
DOE OSTI2025

A Scientist-in-the-Loop Data Analytics Framework for Intelligent Simulation Model Tuning and Validation

This project developed a scientist-in-the-loop data analytics framework for intelligent simulation model tuning and validation, targeting the Weather Research and Forecasting (WRF) model and its solar energy variant, WRF-Solar-BNL. Domain experts, such as climate scientists, depend on large-scale numerical simulations for knowledge discovery and decision-making, yet the complexity of parameter tuning and the disconnect between automated optimization and domain expertise pose significant challenges. We extended an interactive visual analytics framework that enables domain experts to observe and intervene in the computational steering process by identifying disagreements between the simulation model, surrogate model, and the expert’s domain knowledge. Using Bayesian Optimization with Gaussian Process Regression as the surrogate model, our system allows users to probe parameter relationships, analyze correlation patterns, and adjust tuning parameters in real time. We developed use cases for solar irradiance forecasting through sustained collaboration with Brookhaven National Laboratory, resolving critical model configuration challenges and achieving meaningful reductions in prediction error. The project supported one PhD student, one MS student, and eight undergraduate students across three Data Science Capstone projects, resulting in one master’s thesis.

Dasgupta, Aritra [New Jersey Institute of Technolo↗
DOE OSTI2023

Geometric Optimization of an Electrochemical Purification Cell to Prevent Corrosion in CSP Plants During Operation

When exposed to moisture or oxygen, molten chloride salts produce corrosive impurities which degrade containment alloys. This can significantly decrease the lifetime and increase costs of molten-salt-based systems. To overcome this barrier, we designed and modeled an electrochemical purification cell to remove the corrosive impurity MgOH+. Various reactor architectures, including continuous stirred tank reactors (CSTRs) and plug flow reactors (PFRs) were investigated. Steady-state thermoelectric properties were evaluated using analytical methods, allowing assessment of the effects of structure and design parameters such as flow rate, cell length, and cross-sectional area of molten salt. The results suggest that our design could most effectively increase reliability and decrease costs of molten-chloride-salt-based systems by protecting them during continuous operation using an annular plug flow reactor.

analytical modeling↗
DOE OSTI2021

Evaluation of silicon carbide as a divertor armor material in DIII-D H-mode discharges

Silicon carbide (SiC) represents a promising but largely untested plasma-facing material (PFM) for next-step fusion devices. In this work, an analytic mixed-material erosion model is developed by calculating the physical (via SDTrimSP) and chemical (via empirical scalings) sputtering yield from SiC, Si, and C. The Si content in the near-surface SiC layer is predicted to increase during D plasma bombardment due to more efficient physical and chemical sputtering of C relative to Si. Silicon erosion from SiC thereby occurs primarily from sputtering of the enriched Si layer, rather than directly from the SiC itself. SiC coatings on ATJ graphite, manufactured via chemical vapor deposition, were exposed to repeated H-mode plasma discharges in the DIII-D tokamak to test this model. The qualitative trends from analytic modeling are reproduced by the experimental measurements, obtained via spectroscopic inference using the S/XB method. Quantitatively the model slightly under-predicts measured erosion rates, which is attributed to uncertainties in the ion impact angle distribution, as well as the effect of edge-localized modes. After exposure, minimal changes to the macroscopic or microscopic surface morphology of the SiC coatings were observed. Compositional analysis reveals Si enrichment of about 10%, in line with expectations from the erosion model. Extrapolating to a DEMO-type device, an order-of-magnitude decrease in impurity sourcing, and up to a factor of 2 decrease in impurity radiation, is expected with SiC walls, relative to graphite, if low C plasma impurity content can be achieved. Furthermore, these favorable erosion properties motivate further investigations of SiC as a low-Z, non-metallic PFM.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Mascon distribution techniques for asteroids and comets

The mass-concentration model is an approach that has been used to model the gravitational fields of irregularly shaped bodies such as asteroids and comets. By this approach, the body is treated as a collection of point masses. The method is conceptually simple, easy to program, valid down to the surface, and capable of modeling arbitrary density heterogeneities. How the mass concentrations are distributed as well as how mass is assigned to these concentrations is, however, nontrivial. These aspects significantly affect the accuracy and efficiency of the gravitational model. In this paper, we frame the distribution process in terms of numerical integration applied to finite volume meshes. We describe a new method using unstructured, curvilinear, finite volume meshes to significantly improve the accuracy of the mass-concentration model. We then compare the accuracy and efficiency of several variations of our distribution technique to those from literature using Asteroid Eros and Bennu as example bodies. Our results show that the mascon model can be as accurate as the analytic polyhedral model at the surface using an equivalent number of computational elements—i.e., mascon to surface facets. We report the improvement in the model’s performance can be mainly attributed to the volume mesh topology while mesh curving can provide modest case-dependent improvements.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

AT2017gfo: Bayesian inference and model selection of multicomponent kilonovae and constraints on the neutron star equation of state

The joint detection of the gravitational wave GW170817, of the short γ-ray burst GRB170817A and of the kilonova AT2017gfo, generated by the the binary neutron star (NS) merger observed on 2017 August 17, is a milestone in multimessenger astronomy and provides new constraints on the NS equation of state. We perform Bayesian inference and model selection on AT2017gfo using semi-analytical, multicomponents models that also account for non-spherical ejecta. Observational data favour anisotropic geometries to spherically symmetric profiles, with a log-Bayes’ factor of ~104, and favour multicomponent models against single-component ones. The best-fitting model is an anisotropic three-component composed of dynamical ejecta plus neutrino and viscous winds. Using the dynamical ejecta parameters inferred from the best-fitting model and numerical–relativity relations connecting the ejecta properties to the binary properties, we constrain the binary mass ratio to q < 1.54 and the reduced tidal parameter to $120\lt \tilde{\Lambda }\lt 1110$. Finally, we combine the predictions from AT2017gfo with those from GW170817, constraining the radius of a NS of 1.4 M ⊙ to 12.2 ± 0.5 km (1σ level). This prediction could be further strengthened by improving kilonova models with numerical-relativity information.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Progress on Understanding Rayleigh–Taylor Flow and Mixing Using Synergy Between Simulation, Modeling, and Experiment

Simultaneous advances in numerical methods and computing, theoretical techniques, and experimental diagnostics have all led independently to better understanding of Rayleigh–Taylor (RT) instability, turbulence, and mixing. In particular, experiments have provided significant motivation for many simulation and modeling studies, as well as validation data. Numerical simulations have also provided data that is not currently measurable or very difficult to measure accurately in RT unstable flows. Thus, simulations have also motivated new measurements in this class of buoyancy-driven flows. This overview discusses simulation and modeling studies synergistic with experiments and examples of how experiments have motivated simulations and models of RT instability, flow, and mixing. First, a brief summary of measured experimental and calculated simulation quantities, of experimental approaches, and of issues and challenges in the simulation and modeling of RT experiments is presented. Implicit large-eddy, direct numerical, and large-eddy simulations validated using RT experimental data are then discussed. This is followed by a discussion of modeling using analytical, modal, buoyancy–drag, and turbulent transport models of RT mixing experiments. The discussion will focus on three-dimensional RT mixing arising from multimode perturbations. Finally, this focused review concludes with a perspective on future simulation, modeling, and experimental directions for further research. Research in simulation and modeling of RT unstable flows, coupled with experiments, has made significant progress over the past several decades. This overview serves as an opportunity to both discuss progress and to stimulate future research on simulation and modeling of this unique class of hydrodynamically unstable turbulent flows.

42 ENGINEERING↗
DOE OSTI2020

Application of an Erosion Wear Model to Predict Wear of Hammer Milling Components

A workable analytical erosion model that relates critical hammermill process parameters (hammermill geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness, toughness, and fatigue ductility) was applied to model wear (more specifically, change in the shape of hammers) in hammer milling operations. Results of the model were compared to experimental observations of the shape of hammers used in the INL Stage 1 Vermeer hammermill. Results showed good agreement between predicted and measured shape of the hammer, and that a quality-by-design (QbD) approach can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

36 MATERIALS SCIENCE↗