Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WHEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Use of the dispersion ratio in estimating the nonlinear properties of an object of diagnosis

An experimental investigation for estimating the nonlinearity of a diagnostic object was carried out on a single-stage, spur gear reducer. The linearity of the properties of spur gearing (including the linearity of its mode of operation) was tested. Torsional vibrations of the driven wheel and transverse (to the meshing plane) vibrations of the drive wheel on its support were taken as the two outputs of the object to be analyzed. The results of the investigation showed that the degree of nonlinearity of a reducing gear is essentially connected with its operating mode, so that different mathematical models of it can correspond to different values of the system parameters.

Balitskiy, F. Y.↗

Analysis of the relationship between errors in manufacture of slot connections and gear drive noises

On the basis of experimental research, an analysis was carried out of the effect of certain errors in manufacture of straight-barrel slots on the noise characteristics of gear drives. In carrying out the experiments, the gear crowns of the test wheels were held immovable, and only the geometric dimensions of the slots and the mutual locations of the individual elements were varied. The investigation of the effect of each factor was carried out under otherwise equal conditions, on 34:56 cog ratio gear pairs (m = 2mm), made of 40 C steel, with a gear crown accuracy of 7 X, machining fineness 7, at a speed v = 7.1 m/sec. The number of slots was 6. The clearance in slot pairs in dimension D, equal to 0.015, 0.05, 0.08 and 0.110 mm, was obtained by change in the outer diameter of the spindle by means of polishing. The results of the tests of the experimental wheels showed that their noise level increases with increase in clearance.

Bodronosov, M. K.↗

Interactions between SAS-C spacecraft nutations and spin control system

The SAS-C spacecraft is stabilized by a momentum biased reaction wheel and passive nutation damper. A closed-loop low-speed spacecraft spin rate control system is included which uses a single-axis gyro and a variable speed range on the reaction wheel. Dynamic instability can result from interactions among the gyro, damper, and spacecraft dynamic unbalance. This instability may be aggravated by gyro angular misalignment, gyro error signals, and spacecraft nutations. Analytic eigenvector, and digital computer analyses of the coupled systems are presented. Mechanisms for instability are described as well as the effects that gyro error signal, tilt, and spacecraft dynamic unbalance produce on control system performance.

Tossman, B. E.↗

Research study on stabilization and control. Modern sampled-data control theory: Stability analysis of the low cost large space telescope system

The pointing stability of the low-cost large space telescope (LST) system was investigated. The low-cost LST is characterized by the use of reaction wheels for the generation of control torques. Because of the critical requirement on the pointing accuracy of the LST, the nonlinear frictional characteristics of the bearings of the reaction wheels were studied which can cause limit cycles in a closed-loop system. Another possible source of pointing error in the LST is due to the effect of quantization and sensor noise. Since the LST is a digital system, digital to analog and analog to digital converters and sensors for positional and rate feedbacks were used. Sensor noise and amplitude quantization causes pointing error in the LST and, in addition, quantization is a nonlinear phenomenon which can cause self-sustained oscillations in the closed-loop system. The dynamic modeling of the single-axis LST is described, and several methods of evaluating the attitude error of the digital LST due to quantization and noise inputs are given.

Kuo, B. C.↗

Vehicle load-equalization system

System uses cables and associated pulleys to form closed-loop suspension system for terrain compensation. Loop causes reactions at each of three wheels in response to loading at remaining wheel. Simplicity of design should be of interest to designers and manufacturers of construction equipment and off-road vehicles.

Creasy, W. K.↗

Study of shuttle imaging microwave system antenna. Volume 1: Conceptual design

A detailed preliminary design and complete performance evaluation are presented of an 11-channel large aperture scanning radiometer antenna for the shuttle imaging microwave system (SIMS) program. Provisions for interfacing the antenna with the space shuttle orbiter are presented and discussed. A program plan for hardware development and a rough order of magnitude (ROM) cost are also included. The conceptual design of the antenna is presented. It consists of a four-meter diameter parabolic torus main reflector, which is a graphite/epoxy shell supported by a graphite/epoxy truss. A rotating feed wheel assembly supports six Gregorian subreflectors covering the upper eight frequency channels from 6.6 GHz through 118.7 GHz, and two three-channel prime forms feed assemblies for 0.6, 1.4, and 2.7 GHz. The feed wheel assembly also holds the radiometers and power supplies, and a drive system using a 400 Hz synchronous motor is described. The RF analysis of the antenna is performed using physical optics procedures for both the dual reflector Gregorian concept and the single reflector prime focus concept. A unique aberration correcting feed for 2.7 GHz is analyzed. A structural analysis is also included. The analyses indicate that the antenna will meet system requirements.

Wesley, R. W.↗

Modern mechanisms make manless Martian mission mobile: Spin-off spells stairclimbing self-sufficiency for earthbound handicapped

Concepts were developed for three wheel chairs from progressively improving designs of a proposed unmanned roving vehicle for the surface exploration of Mars; as a spin-off, a concept for a stair-climbing wheel chair was generated. The mechanisms employed in these are described. The Mars mission is envisioned using the booster rockets and aeroshell of the Viking missions.

Sandor, G. N.↗

Landing gear and cavity noise prediction

Prediction of airframe noise radiation from the landing gear and wheel wells of commercial aircraft is examined. Measurements of these components on typical aircraft are presented and potential noise sources identified. Semiempirical expressions for the sound generation by these sources are developed from available experimental data and theoretical analyses. These expressions are employed to estimate the noise radiation from the landing gear and wheel wells for a typical aircraft and to rank order the component sources.

Bliss, D. B.↗

Space telescope optical telescope assembly/scientific instruments. Phase B: Preliminary design and program definition study. Volume 2A(3): Astrometry

Wide field measurements, namely, measurements of relative angular separations between stars over a relatively wide field for parallax and proper motion determinations, were made with the third fine guidance sensor. Narrow field measurements, i.e., double star measurements, are accomplished primarily with the area photometer or faint object camera at f/96. The wavelength range required can be met by the fine guidance sensor which has a spectral coverage from 3000 to 7500 A. The field of view of the fine guidance sensor also exceeds that required for the wide field astrometric instrument. Requirements require a filter wheel for the wide field astrometer, and so one was incorporated into the design of the fine guidance sensor. The filter wheel probably would contain two neutral density filters to extend the dynamic range of the sensor and three spectral filters for narrowing effective double star magnitude difference.

Source record↗

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces - A velocity-rate-controlled, pressure-bias-modulated system

During maximum braking the average ratio of drag-force friction coefficient developed by the antiskid system to maximum drag-force friction coefficient available at the tire/runway interface was higher on dry surfaces than on wet surfaces. The gross stopping power generated by the brake system on the dry surface was more than twice that obtained on the wet surfaces. With maximum braking applied, the average ratio of side-force friction coefficient developed by the tire under antiskid control to maximum side-force friction available at the tire/runway interface of a free-rolling yawed tire was shown to decrease with increasing yaw angle. Braking reduced the side-force friction coefficient on a dry surface by 75 percent as the wheel slip ratio was increased to 0.3; on a flooded surface the coefficient dropped to near zero for the same slip ratio. Locked wheel skids were observed when the tire encountered a runway surface transition from dry to flooded, due in part to the response time required for the system to sense abrupt changes in the runway friction; however, the antiskid system quickly responded by reducing brake pressure and cycling normally during the remainder of the run on the flooded surface.

Stubbs, S. M.↗

Real time reflectometer

A real time reflectometer with the particular utility of measuring fairly rapid (transient) changes in the specular reflectance of a sample which is continuously exposed to a perturbing environment is described. A fixed radiation source, a fixed detector, a uniformly rotating sample wheel, and a uniformly rotating optical wheel protect against misalignment problems. The reflectometer operates by comparing the measurings of a reflected signal with that of a reference signal made within fractions of a second of one another. Reflectance is measured in the infrared, visible, and vacuum ultraviolet regions.

Zwiener, J. M.↗

Design definition of a mechanical capacitor

A design study and analyses of a 10 kW-hr, 15 kW mechanical capacitor system was studied. It was determined that magnetically supported wheels constructed of advanced composites have the potential for high energy density and high power density. Structural concepts are analyzed that yield the highest energy density of any structural design yet reported. Particular attention was paid to the problem of 'friction' caused by magnetic and I to the second power R losses in the suspension and motor-generator subsystems, and low design friction levels have been achieved. The potentially long shelf life of this system, and the absence of wearing parts, provide superior performance over conventional flywheels supported with mechanical bearings. Costs and economies of energy storage wheels were reviewed briefly.

Michaelis, T. D.↗

An experimental investigation of airframe component interference noise

Measurements of noise produced by a model of a wheel well (rectangular cavity), landing gear (wheel and strut), and flap at Mach numbers of 0.18 and 0.40 have been made in an anechoic flow facility. Individual component noise and component interference noise are described in terms of the OASPL, spectra, and streamwise or flyover directivity patterns. Areas of significant sound generation are illuminated and causes of these noise sources are suggested. Results from an acoustic imaging technique are used to point out other source regions not discernible by simple far-field measurements.

Block, P. J. W.↗

Optical scanning system for laser velocimeter

An optical system was developed to provide fast incremental scanning of a backscattered laser velocimeter focus point over a 36-cm distance. The system is used to measure flow velocities at 16 positions along its optical axis and to scan these 16 positions up to 30 times a second. Dwell time at each location is approximately 2 milliseconds. Sample volumes typically are 0.2 mm in diameter by 1.4 cm in length. The optical scanning system consists of a wheel containing plane parallel quartz windows of various thicknesses. The laser velocimeter beams are imaged to a primary focus within the dead airspace of an optical cell. The beams emerging from the cell pass through the windows of the scanning wheel. The refraction of the beams passing through the windows causes an apparent shift of the focus within the optical cell and hence in the test zone. Light scattered from the secondary focus within the test zone is concurrently collected and reimaged through the same optical path which originally projected the primary focus. The reimaged backscattered light containing the velocity information is then collected and focused onto a photomultiplier detector system to complete the scanned laser velocimeter optical system.

Rhodes, D. B.↗

Full color hybrid display for aircraft simulators

A full spectrum color monitor, connected to the camera and lens system of a television camera supported by a gantry frame over a terrain model simulating an aircraft landing zone, projects the monitor image onto a lens or screen visually accessible to a trainee in the simulator. A digital computer produces a pattern corresponding to the lights associated with the landing strip onto a monochromatic display, and an optical system projects the calligraphic image onto the same lens so that it is superposed on the video representation of the landing field. The optical system includes a four-color wheel which is rotated between the calligraphic display and the lens, and an apparatus for synchronizing the generation of a calligraphic pattern with the color segments on the color wheel. A servo feedback system responsive to the servo motors on the gantry frame produces an input to the computer so that the calligraphically generated signal corresponds in shape, size and location to the video signal.

Chase, W. D.↗

Summary of NASA landing-gear research

This paper presents a brief summary of the airplane landing gear research underway at NASA. The technology areas include: ground handling simulator, antiskid braking systems, space shuttle nose-gear shimmy, active control landing gear, wire brush skid landing gear, air cushion landing systems, tire/surface friction characteristics, tire mechanical properties, tire-tread materials, powered wheels for taxiing, and crosswind landing gear. This paper deals mainly with the programs on tire-tread materials, powered wheel taxiing, air cushion landing systems, and crosswind landing gear research with particular emphasis on previously unreported results of recently completed flight tests. Work in the remaining areas is only mentioned.

Fisher, B. D.↗

Evaluation of the propulsion control system of a planetary rover and design of a mast for an elevation scanning laser/multi-detector system

Vertical wheel loads, wheel speeds, and torque relationships are considered in the design of a propulsion system capable of responding to steering, slope climbing, and irregular local terrains. The system developed is applied to the RPI Mars roving vehicle. The mechanical system required to implement the elevation laser scanning/multidetector principle was the design and construction of a mechanical system for implementing the elevation scanning/multidetector principle is also discussed.

Knaub, D.↗

The high-energy celestial X-ray instrument on board OSO-8

The 20 keV-3 MeV celestial X-ray detector on the OSO-8 is described. The primary objectives of this instrument are to measure the energy spectrum of cosmic X-ray sources above 20 keV and to search for time variations, both periodic and irregular, in the intensity of the sources detected. The detector consists of two optically isolated central crystals shielded by a large, active collimator. The sensitive area is 27.5 sq cm and the field-of-view is 5 deg FWHM. The instrument is mounted in the wheel section of OSO-8 with the axis of its field of view offset by 5 deg from the negative spin axis of the wheel. The minimum detectable intensity of a point source which is brought to within 5 deg of the negative spin axis for greater than one day is about 10 to the minus fifth power photons/sq cm-sec at 100 keV.

Dennis, B. R.↗