SEARCH · Engineering Papers

Results for “Stabilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Application of the finite-state arbitrary-motion aerodynamics to rotor blade aeroelastic response and stability in hover and forward flight

The primary objective of this paper is to illustrate the influence of finite-state arbitrary-motion time-domain aerodynamics on rotor blade aeroelastic stability in hover and forward flight. The essential ingredients of the generalized Greenberg type time-domain unsteady aerodynamics are presented and incorporated in a coupled nonlinear flap-lag analysis. Aeroelastic stability boundaries for both hover and forward flight are obtained using both arbitrary-motion time-domain aerodynamics and quasi-steady aerodynamics. The sensitivity of flap-lag aeroelastic stability boundaries to time-domain arbitrary-motion unsteady aerodynamics is evaluated by comparing the two sets of results for various blade configurations and flight conditions.

Dinyavari, M. A. H.↗

NASA NTRS1984

Aeromechanical stability of a full-scale hingeless rotor in hover

The aeroelastic stability in hover of a 9.8-m-diam, hingeless helicopter rotor system is evaluated. Rotor inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients between 0.0 and 0.12. At constant rotor rotational speed, a minimum inplane damping level was obtained at a thrust coefficient of approximately 0.02. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Correlation with a comprehensive aeroelastic stability program is found to be good. The influence of different aerodynamic inflow models on predicted damping levels is shown. Best correlation with experimental data is obtained using a dynamic inflow model rather than static or quasi-static inflow models. Comparison with other full-scale, hingeless rotor stability data in hover is presented. Also, direct comparisons are made with data from a full-scale bearingless main rotor test performed on the same general-purpose test apparatus. Although the bearingless rotor is more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown.

Peterson, R. L.↗

NASA NTRS1984

Stability and control results for advanced turboprop aft-mount installations

An experimental investigation was recently conducted in the NASA-Langley Research Center 4- by 7-Meter Tunnel to explore the effects of aft-mounted advanced turboprop installations on the low-speed stability and control characteristics of a representative transport aircraft configuration. For the conditions investigated, the experimental results indicate that the longitudinal and directional stability of the configuration was not adversely affected by aft-pylon-mounted single-rotation tractor or counter-rotation pusher propeller installations. The results indicate that for the single-rotation tractor configuration the propeller induced aerodynamics are dominated by the interaction of the propeller slipsteam with the pylon, and that the propeller contribution to the stability characteristics for the counter-rotating pusher configuration is dominated by propeller normal forces. The longitudinal and directional control effectiveness, engine-out characteristics, and ground effects are also presented.

Coe, P. L., Jr.↗

NASA NTRS1985

Coated oxidizers for combustion stability in solid-propellant rockets

Experiments are conducted in a laboratory-scale (6.25-cm diameter) end-burning rocket motor with state-of-the-art, ammonium perchlorate hydroxy-terminated polybutadiene (HTPB), nonmetallized propellants. The concept of tailoring the stability characteristics with a small amount (less than 1 percent by weight) of COATING on the oxidizer is explored. The thermal degradation characteristics of the coat chemical are deduced through theoretical arguments on thermal diffusivity of the composite material (propellant). Several candidate coats are selected and propellants are cast. These propellants (with coated oxidizers) are fired in a laboratory-scale end-burning rocket motor, and real-time pressure histories are recorded. The control propellant (with no coating) is also tested for comparison. The uniformity of the coating, confirmed by SEM pictures and BET adsorption measurements, is thought to be an advance in technology. The frequency of bulk mode instability (BMI), the pressure fluctuation amplitudes, and stability boundaries are correlated with parameters related to the characteristic length (L-asterisk) of the rocket motor. The coated oxidizer propellants, in general, display greater combustion stability than the control (state-of-the-art). The correlations of the various parameters are thought to be new to a field filled with much uncertainty.

Helmy, A. M.↗

NASA NTRS1985

Morphological Stability and Fluid Dynamics of Vapor Crystal Growth

A fundamental understanding of the conditions under which crystals can retain morphological stability, i.e., shape stability of the advancing interface, during growth from vapors was studied. Morphological stability (MS) is a necessary condition for the growth of homogeneous single crystals required for numerous device applications. For crystallization from melts, the MS concepts are well developed and are essentially based on heat and mass transfer conditions about the advancing interface. For crystallization from vapors, the MS requirements are more complex and not well understood. The added complexity arises from the fact that anisotropies in interfacial kinetics are typically stronger in crystallization from vapors than from melts. These pronounced anisotropies root in the distinctly lower atomic roughness of most vapor-solid interfaces.

Rosenberger, F.↗

NASA NTRS1985

A numerical study of global axisymmetric states and their stability to quasi-geostrophic disturbances

A steady, axisymmetric model of the general circulation is developed as a basis for climate stability studies. The model includes the effects of heating, rotation, and internal friction, but neglects topography. It is assumed that the axisymmetric flow may be modeled by making the Boussinesq and deep convection approximations. The hydrostatic assumption is not made, thus permitting the advective terms to be included in the vertical equation of motion. The initial set of five primitive equations is reduced to three equations in terms of the zonal velocity, meridional streamfunction, and the potential temperature perturbation. The application of the Boussinesq, deep convection, and quasi-geostrophic assumptions limits the ranges of the heating and rotation rates. For values not too far from typical atmospheric values, the model produces a stability boundary separating Hadley from Rossby flow. The boundary is characterized by a particular value of vertical wind shear, which suggests that baroclinic instability is the primary mechanism for the loss of stability. The initial growth rates are largest for longitudinal waves 4-7, also in agreement with studies of baroclinic instability.

Henderson, H. W.↗

NASA NTRS1985

Interactive aircraft flight control and aeroelastic stabilization

Aeroservoelastic optimization techniques were studied to determine a methodology for maximization of the stable flight envelope of an idealized, actively controlled, flexible airfoil. The equations of motion for the airfoil were developed in state-space form to include time-domain representations of aerodynamic forces and active control. The development of an optimization scheme to stabilize the aeroelastic system over a range of airspeeds, including the design airspeed is outlined. The solution approach was divided in two levels: (1) the airfoil structure, with a design variable represented by the shear center position; and (2) the control system. An objective was stated in mathematical form and a search was conducted with the restriction that each subsystem be constrained to be optimal in some sense. Analytical expressions are developed to compute the changes in the eigenvalues of the closed-loop, actively controlled system. A stability index is constructed to ensure that stability is present at the design speed and at other airspeeds away from the design speed.

Weisshaar, T. A.↗

NASA NTRS1985

A method to stabilize linear systems using eigenvalue gradient information

Formal optimization methods and eigenvalue gradient information are used to develop a stabilizing control law for a closed loop linear system that is initially unstable. The method was originally formulated by using direct, constrained optimization methods with the constraints being the real parts of the eigenvalues. However, because of problems in trying to achieve stabilizing control laws, the problem was reformulated to be solved differently. The method described uses the Davidon-Fletcher-Powell minimization technique to solve an indirect, constrained minimization problem in which the performance index is the Kreisselmeier-Steinhauser function of the real parts of all the eigenvalues. The method is applied successfully to solve two different problems: the determination of a fourth-order control law stabilizes a single-input single-output active flutter suppression system and the determination of a second-order control law for a multi-input multi-output lateral-directional flight control system. Various sets of design variables and initial starting points were chosen to show the robustness of the method.

Wieseman, C. D.↗

NASA NTRS1985

Flap-Lag-Torsion Stability in Forward Flight

An aeroelastic stability of three-degree flap-lag-torsion blade in forward flight is examined. Quasisteady aerodynamics with a dynamic inflow model is used. The nonlinear time dependent periodic blade response is calculated using an iterative procedure based on Floquet theory. The periodic perturbation equations are solved for stability using Floquet transition matrix theory as well as constant coefficient approximation in the fixed reference frame. Results are presented for both stiff-inplane and soft-inplane blade configurations. The effects of several parameters on blade stability are examined, including structural coupling, pitch-flap and pitch-lag coupling, torsion stiffness, steady inflow distribution, dynamic inflow, blade response solution and constant coefficient approximation.

Panda, B.↗

NASA NTRS1985

Exploratory low-speed wind-tunnel study of concepts designed to improve aircraft stability and control at high angles of attack

A wind tunnel investigation of concepts to improve the high angle-of-attack stability and control characteristics of a high performance aircraft was conducted. The effect of vertical tail geometry on stability and the effectiveness of several conventional and unusual control concepts was determined. These results were obtained over a large angle-of-attack range. Vertical tail location, cant angle and leading edge sweep could influence both longitudinal and lateral-directional stability. The control concepts tested were found to be effective and to provide control into the post stall angle-of-attack region.

Hahne, D. E.↗

NASA NTRS1986

Low-speed stability and control characteristics of a transport model with aft-fuselage-mounted advanced turboprops

A limited experimental investigation was conducted in the Langley 4- by 7-Meter Tunnel to explore the effects of aft-fuselage-mounted advanced turboprop installations on the low-speed stability and control characteristics of a representative transport aircraft in a landing configuration. In general, the experimental results indicate that the longitudinal and lateral-directional stability characteristics for the aft-fuselage-mounted single-rotation tractor and counter-rotation pusher propeller configurations tested during this investigation are acceptable aerodynamically. For the single-rotation tractor configuration, the propeller-induced aerodynamics are significantly influenced by the interaction of the propeller slipstream with the pylon and nacelle. The stability characteristics for the counter-rotation pusher configuration are strongly influenced by propeller normal forces. The longitudinal and directional control effectiveness, engine-out characteristics, and ground effects are also presented. In addition, a tabulated presentation of all aerodynamic data presented in this report is included as an appendix.

Applin, Z. T.↗

NASA NTRS1986

The measurement of aircraft performance and stability and control after flight through natural icing conditions

The effects of airframe icing on the performance and stability and control of a twin-engine commuter-class aircraft were measured by the NASA Lewis Research Center. This work consisted of clear air tests with artificial ice shapes attached to the horizontal tail, and natural icing flight tests in measured icing clouds. The clear air tests employed static longitudinal flight test methods to determine degradation in stability margins for four simulated ice shapes. The natural icing flight tests employed a data acquisition system, which was provided under contract to NASA by Kohlman Systems Research Incorporated. This system used a performance modeling method and modified maximum likelihood estimation (MMLE) technique to determine aircraft performance degradation and stability and control. Flight test results with artificial ice shapes showed that longitudinal, stick-fixed, static margins are reduced on the order of 5 percent with flaps up. Natural icing tests with the KSR system corroborated these results and showed degradation in the elevator control derivatives on the order of 8 to 16 percent depending on wing flap configuration. Performance analyses showed the individual contributions of major airframe components to the overall degration in lift and drag.

Ranaudo, R. J.↗

NASA NTRS1985

Remarks on rotor stability (A contribution to discussion during symposium on instability in rotating machinery)

Influence of nonlinear factors in fluid lubricated bearings on rotor vibrations is discussed as are computation of threshold of stability for systems with multiple degrees of freedom. The reason for this investigation was to learn more about the influence of tilting pad bearings on vertical rotors. The eigenvalues, the stability threshold, the response on the Heaviside-function and the unbalance response were calculated for a rigid rotor, a Jeffcott rotor and for the finite element model of a real rotor. The comparison of the linear and nonlinear calculations shows the limit of the linear calculations. The computation is supposed to show, that the model of the Jeffcott rotor is not sufficient in most practical cases to determine the stability threshold. This was known for some years, when computed results were compared with the behavior of real machines. That's why a program was developed, which is roughly described.

Kraemer, E.↗

NASA NTRS1981

Longitudinal stability and control derivatives obtained from flight data of a PA-30 aircraft

In order to obtain reliable and accurate values of the stability and control derivatives, the Dryden Fligh Research Center (DFRC) developed a technique for extracting the derivatives from flight data. This technique is implemented by a set of FORTRAN computer programs that is based on a modified maximum likelihood estimator that uses the Newton-Raphson algorithm to perform the required minimization of the derivatives. Data was obtained with a PA-30, light twin-engine general aviation aircraft in zero, half, and full flap configuration in level unaccelerated flight with the landing gear retracted. The derivatives were plotted as functions of angle of attack using various graphical arrangements to show variations of wind tunnel and flight determined values at zero flap settings. Also, data was displayed to show the effects of flap deflection and thrust variation on the longitudinal stability derivatives. The angle of attack and angle of sideslip were measured. The dynamic pressure, velocity, and altitude were calculated, using a FORTRAN computer program, from the static and dynamic pressures. The control deflections of the stabilator, ailerons, and rudder also were recorded along with left throttle position, engine rpm, and manifold pressure.

Turley, D. R.↗

NASA NTRS1986

Effect of thermal expansion on the stability of two-reactant flames

The full problem of flame stability for the two-reactant model, which takes into account thermal expansion effects for all disturbance wave lengths, is examined. It is found that the stability problem for the class of two-reactant flames is equivalent to the stability problem for the class of one-reactant flames with an appropriate interpretation of Lewis numbers.

Jackson, T. L.↗

NASA NTRS1985

Thermal stability of static coronal loops. I - Effects of boundary conditions

The linear stability of static coronal-loop models undergoing thermal perturbations was investigated. The effect of conditions at the loop base on the stability properties of the models was considered in detail. The question of appropriate boundary conditions at the loop base was considered and it was concluded that the most physical assumptions are that the temperature and density (or pressure) perturbations vanish there. However, if the base is taken to be sufficiently deep in the chromosphere, either several chromospheric scale heights or several coronal loop lengths in depth, then the effect of the boundary conditions on loop stability becomes negligible so that all physically acceptable conditions are equally appropriate. For example, one could as well assume that the velocity vanishes at the base. The growth rates and eigenmodes of static models in which gravity is neglected and in which the coronal heating is a relatively simple function, either constant per-unit mass or per-unit volume were calculated. It was found that all such models are unstable with a growth rate of the order of the coronal cooling time. The physical implications of these results for the solar corona and transition region are discussed.

Antiochos, S. K.↗

NASA NTRS1984

Helicopter attitude stabilization using individual-blade-control

A theoretical study is presented on the application of the Individual-Blade-Control concept to helicopter attitude stabilization. The design of a system controlling blade flapping dynamics, and related testing of the system on a model rotor in the wind tunnel, is described. The control inputs considered are blade pitch changes proportional to blade flapping acceleration, velocity, and displacement. The effect of such a system on helicopter rotor damping-in-pitch, and angle-of-attack stability is then evaluated. It is shown that helicopter attitude stabilization is achieved, with a corresponding improvement in flying qualities.

Ham, N. D.↗

NASA NTRS1985

Environmental stability of intercalated graphite fibers

Graphite fibers intercalated with bromine, iodine monochloride, ferric chloride, and cupric chloride were subjected to stability tests under four environments which are encountered by engineering materials in the aerospace industry: ambient laboratory conditions, as would be experienced during handling operations and terrestrial applications; high vacuum, as would be experienced in space applications; high humidity, as would be experienced in marine applications; and high temperature, as would be experienced in some processing steps and applications. Monitoring the resistance of the fibers at ambient laboratory conditions revealed that only the ferric chloride intercalated fibers were unstable, due to absorption of water from the air. All four types of intercalated fibers were unstable, due to absorption of water from the air. All four types of intercalated fibers were stable for long periods under high vacuum. Ferric chloride, cupric chloride, and iodine monochloride intercalated fibers were sensitive to high humidity conditions. All intercalated fibers began to degrade above 250 C. The order of their thermal stability, from lowest to highest, was cupric chloride, iodine monochloride, bromine, and ferric chloride. Of the four types of intercalated fibers tested, the bromine intercalated fibers appear to have the most potential for application, based on environmental stability.

Gaier, J. R.↗