Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Microstructural Development of Directionally Solidified Hg(1-x)Zn(x)Se Alloys

Hg(1-x)Zn(x)Se alloys have been studied as an alternative to HgCdTe for the detection of electromagnetic radiation, because the shorter ZnSe and HgSe bonds were predicted to improve lattice stability. Previous studies showed that optical properties were stable with time and that the microhardness was higher than for HgTe based alloys. However, for this material to be commercially viable, compositional variations must be reduced, and the distribution of defects induced by the growth process must be understood. The basic structural properties of bulk materials were characterized, and dislocation etch pit densities were measured to determine whether the addition of Zn to the HgSe lattice reduced the potential for dislocation formation. Hg(0.9)Zn(0.1)Se alloys were directionally solidified using a modified Bridgman-Stockbarger method and in an applied magnetic field. Radial compositional variations were greatly reduced when solidification occurred in an applied magnetic field. The combination of a convex liquid-solid interface shape and a method for reduced wetting produced boules that were a single crystal after reaching full diameter. Observed surface features indicated ampoule wetting could be eliminated using a graphite getter. Microstructural characteristics were greatly improved over HgCdTe alloys, In six boules, a total of only one twin was observed, and no inclusions were found. A method for polishing and producing dislocation etch pits was developed for these alloys, revealing dislocation etch pit densities one to two orders of magnitude less than HgTe based alloys. A kink in the thermal profile during processing of one boule generated more dislocations than did lattice mismatch due to compositional variations. The results of this investigation indicate this alloy has improved microstructural properties and resistance to dislocation formation compared with similar II-VI alloys, and should be further investigated for the detection of electromagnetic radiation.

Cobb, S. D.↗

ExaCA: A performance portable exascale cellular automata application for alloy solidification modeling

Modeling the as-solidified grain structures that form during alloy processing is a critical component in understanding process-property relationships, particularly for additive manufacturing (AM) where grain structure is very sensitive to processing conditions. While cellular automata (CA)-based models have proven able to predict aspects of microstructure for several alloys and AM process conditions, long run times and large resource sets required limit the utility and the problem size to which existing CA models can be applied. As part of the ExaAM project, an initiative within the Exascale Computing Project (ECP) to develop, test, and optimize an exascale-capable coupled and self-consistent model of AM parts, we developed ExaCA (https://github.com/LLNL/ExaCA) for the liquid–solid phase transformation in the wake of AM melt pools. The CA-based code is parallelized using MPI and the Kokkos programming model, the latter enabling simulation on both CPUs and GPUs within a single-source implementation. Here, we detail the steps taken to transform a baseline, MPI-based CA code into one that is performant on CPUs and GPUs. Performance testing of ExaCA on Summit (a pre-exascale machine at Oak Ridge National Laboratory) was used to quantify CPU–GPU speedup comparing with equal numbers of nodes. Testing showed comparable CPU performance to the MPI-only CA code and a 5-20x speedup when running AM-based test problems using GPUs. The improved performance of CA through GPU utilization and the performance portable nature of ExaCA will enable accurate part-scale modeling by harnessing the power of current and future generations of high performance computing resources. Future work will include improving the strong scaling of ExaCA on GPUs by reducing load imbalance associated with the locality of the problem, and continuing performance optimization across exascale hardware.

36 MATERIALS SCIENCE↗

High-rate Plastic Deformation of Nanocrystalline Tantalum to Large Strains: Molecular Dynamics Simulation

Recent advances in the ability to generate extremes of pressure and temperature in dynamic experiments and to probe the response of materials has motivated the need for special materials optimized for those conditions as well as a need for a much deeper understanding of the behavior of materials subjected to high pressure and/or temperature. Of particular importance is the understanding of rate effects at the extremely high rates encountered in those experiments, especially with the next generation of laser drives such as at the National Ignition Facility. Here we use large-scale molecular dynamics (MD) simulations of the high-rate deformation of nanocrystalline tantalum to investigate the processes associated with plastic deformation for strains up to 100%. We use initial atomic configurations that were produced through simulations of solidification in the work of Streitz et al [Phys. Rev. Lett. 96, (2006) 225701]. These 3D polycrystalline systems have typical grain sizes of 10-20 nm. We also study a rapidly quenched liquid (amorphous solid) tantalum. We apply a constant volume (isochoric), constant temperature (isothermal) shear deformation over a range of strain rates, and compute the resulting stress-strain curves to large strains for both uniaxial and biaxial compression. We study the rate dependence and identify plastic deformation mechanisms. The identification of the mechanisms is facilitated through a novel technique that computes the local grain orientation, returning it as a quaternion for each atom. This analysis technique is robust and fast, and has been used to compute the orientations on the fly during our parallel MD simulations on supercomputers. We find both dislocation and twinning processes are important, and they interact in the weak strain hardening in these extremely fine-grained microstructures.

36 MATERIALS SCIENCE↗

A compact and flexible induction furnace for in situ X-ray microradiograhy and computed microtomography at Elettra: design, characterization and first tests

A compact and versatile induction furnace for in situ high-resolution synchrotron and laboratory hard X-ray microradiography and computed microtomography is described. The furnace can operate from 773 to 1723 K. Its programmable controller enables the user to specify multiple heating and cooling ramp rates as well as variable dwell times at fixed temperatures allowing precise control of heating and cooling rates to within 5 K. The instrument can work under a controlled atmosphere. Thanks to the circular geometry of the induction coils, the heat is homogeneously distributed in the internal volume of the graphite cell ( ca . 150 mm 3 ) where the sample holder is located. The thermal gradient within the furnace is less than 5 K over a height of ca . 5 mm. This new furnace design is well suited to the study of melting and solidification processes in geomaterials, ceramics and several metallic alloys, allowing fast heating (tested up to 6.5 K s -1 ) and quenching (up to 21 K s -1 ) in order to freeze the sample microstructure and chemistry under high-temperature conditions. The sample can be held at high temperatures for several hours, which is essential to follow phenomena with relatively slow dynamics, such as crystallization processes in geomaterials. The utility of the furnace is demonstrated through a few examples of experimental applications performed at the Elettra synchrotron laboratory (Trieste, Italy).

Kudrna Prašek, Marko↗

Specific Adaptation of Gas Atomization Processing for Al-Based Alloy Powder for Additive Manufacturing

The initial three atomization attempts resulted in “freeze-outs” within the pour tubes in the pilot-scale system and yielded no powder. Re-evaluation of the alloy liquidus temperatures and melting characteristics, in collaboration with Alcoa, showed further superheat to be necessary to allow the liquid metal to flow through the pour tube to the atomization nozzle. A subsequent smaller run on the experimental atomization system verified these parameters and was successful, as were all successive runs on the larger pilot scale system. One alloy composition froze-out part way through the atomization on both pilot scale runs. SEM images showed needle formation and phase segregations within the microstructure. Analysis of the pour tube freeze-out microstructures showed that large needles formed within the pour tube during the atomization experiment, which eventually blocked the melt stream. Alcoa verified the needle formation in this alloy using theoretical modeling of phase solidification. Sufficient powder of this composition was still generated to allow powder characterization and additive manufacturing trials at Alcoa.

36 MATERIALS SCIENCE↗

Solidification studies of Nb-Ge alloys at large degrees of supercooling

A 32 meter evacuated drop tube has been used to investigate the solidification of Nb-Ge alloys after deep undercooling. Samples have been supercooled as much as 500 K below the liquidus by using free-fall conditions to eliminate crucible induced nucleation. Final microstructures are dependent on the quenching rates at the bottom of the drop tube with a striking extension of the beta phase solubility limit at the higher quenching rates.

Lacy, L. L.↗

Results of the technical exchange agreement between NASA and DuPont on the containerless drop tube solidification of NiAl3

The final results of the Drop Tube Solidification of NiAl3 are presented. Problems associated with the utilization of a dripper furnace in the drop tube are discussed and the modification of experimental procedures required to achieve results are described. Sample microstructures of drop tube samples are compared with other samples. The dendrite arm spacings of drop tube samples are correlated with the rapid cooling rates.

Ethridge, E. C.↗

Effect of Ni Addition to Sn0.7Cu Solder Alloy on Thermal Behavior, Microstructure, and Mechanical Properties

The addition of Ni on lead-free solder alloys Sn0.7Cu was tested in this study. A small amount of Ni was added to the solder alloys to evaluate the thermal behavior, microstructure, and mechanical properties of the composite solders after sintering and isothermal aging for 3 days and then compared with the results of the binary Sn0.7Cu solder. The results indicated that the ultimate tensile strength and yield tensile strength changed when adding 0.25 wt.% of Ni. The tested results of the differential scanning calorimeter showed that the addition of Ni (such as 0.5 and 1 wt.%) could obviously increase the solidification temperature of Sn0.7Cu alloys in the cooling process. When the Ni content was increased to 0.25 wt.% in the ternary condition, which includes the Sn0.7Cu-xNi (x = 0, 0.1, 0.25, 0.5, and 1 wt.%) solder alloys for the indentation creep test, the minimum creep rate reached the maximum; however, the trend was reversed as the Ni content was higher than this level. In addition, the microstructure of Sn-0.7Cu-xNi solder alloys was obviously different with the eutectic Sn-0.7Cu solder, such that the Ni gradually accumulated in the (Cu, Ni){sub 6}Sn{sub 5} IMCs within the Ni-containing solder alloys. Additionally, this process refined the microstructure of the Sn-0.7Cu solder. The fracture surface of the eutectic Sn-0.7Cu solder revealed ductile fracture modes; however, there was no mixed ductile–brittle fracture mode occurred when the Ni content was in the range of 0-1 wt.%.

36 MATERIALS SCIENCE↗

Microstructural evaluation of thin-wall sections of 316L stainless steel produced by laser powder-bed fusion processing

Laser powder bed fusion (LBPF) is a method of additive manufacturing (AM) that offers a means to fabricate complex components with features which rely upon the mechanical integrity of thin-wall (less than 0.4 mm thick) structures. The microstructure of a 316L AM thin wall is investigated as metallographically prepared from a cylindrical shell. Optimization is pursued through mechanical polishing and chemical etching to minimize the effects of surface roughness. Microanalysis measurements of the sectioned component reveal the sample has high microstructural fidelity, uniform composition and phase content across grain as well as powder layer boundaries within the thin wall. The results are attributed to a uniform thermal gradient at the part scale during rapid solidification.

36 MATERIALS SCIENCE↗

Test and evaluation of Apollo 14 composite casting demonstration specimens 6, 9, and 12, phase 1

Flight and control specimens 6, 9, and 12 from the Apollo 14 composite casting demonstration were evaluated with respect to the degree of dispersion achieved for mixtures of immiscible materials under one-gravity and low gravity environments. The flight and control capsules 6, 9, and 12 contained paraffin and sodium acetate; paraffin, sodium acetate and argon; and paraffin, sodium acetate and 100 micrometer diameter tungsten microspheres, respectively. The evaluation and documentation utilized photographic and microstructure examinations, density measurements, and droplet size and distribution determinations. In addition, theoretical analyses were performed in order to aid in the understanding of the fluid behavior of the specimens during processing and subsequent solidification. A comparison of evaluated data with the theoretical analyses reveals that although the immiscible materials were uniquely dispersed in a low gravity environment, nonuniform dispersions were obtained primarily due to insufficient initial mixing and an essentially unidirectional thermal gradient during cooldown.

Reger, J. L.↗

Liquidus Temperatures and Solidification Behavior in the Copper-Niobium System

The copper-niobium phase diagram has been under active debate; thus, a corroboratory experimental study is needed. In this investigation, the melts of Cu-Nb alloys at compositions ranging from 5 lo 86 wt% Nb were processed in different environments and solidified at relatively low rates of 50-75 C/s to determine liquidus temperatures and to study solidification behavior. For all samples processed under very clean conditions, only Nb dendrites in a Cu matrix were observed; while in the presents of oxygen impurities, the alloys containing 5-35 wt% Nb exhibited microstructure of Nb-rich spheroids and Nb dendrites in the Cu matrix. The results obtained from clean conditions are in fair agreement with the Cu-Nb phase diagram having an S-shaped, near-horizontal appearances of the liquidus. The formation of Nb-rich droplets at slow cooling rates is discussed in terms of a stable liquid miscibility gap induced by oxygen.

Li, D.↗

The Effect of Brazing on Microstructure of Honeycomb Liner Material Hastelloy X

Labyrinth seals with abradable metallic honeycomb structures are common in gas turbines to ensure a tight sealing between rotor and stator. These seals have a big impact on the turbine efficiency. The honeycombs made from nickel-based superalloys are brazed onto backing segments in order to form liners. In this work, the microstructure of Hastelloy X honeycombs after brazing with a nickel-chromium-silicon braze filler alloy is investigated. It was found that the braze filler can wet the honeycomb foils over their entire height up to the contact surface with the rotor. After solidification, the braze filler alloy forms γ and silicides (NiSi and Ni{sub y}(Mo, Cr){sub x}Si). The intermetallic silicides give high hardness to the honeycomb liners. Between the braze filler alloy and the honeycomb foils, interdiffusion zones are observed. For the rub-in behavior of the honeycomb liners, not only the foil material but also the comportment of the composite made up of the foil material, the braze filler material and the interdiffusion zones has to be considered.

36 MATERIALS SCIENCE↗

Powder bed binder jet 3D printing of Inconel 718: Densification, microstructural evolution and challenges

Traditional manufacturing of Inconel 718 components from castings and thermomechanical processing routes involve extensive post processing and machining to attain the desired geometry. Additive manufacturing (AM) technologies including direct energy deposition (DED), selective laser melting (SLM), electron beam melting (EBM) and binder jet 3D printing (BJ3DP) can minimize scrap generation and reduce lead times. While there is extensive literature on the use of melting and solidification based AM technologies, there has been limited research on the use of binder jet 3D printing. In this paper, a brief review on binder jet additive manufacturing of Inconel 718 is presented. In addition, existing knowledge on sintering of Inconel 718 has been extended to binder jet 3D printing. We found that supersolidus liquid phase sintering (SLPS) is necessary to achieve full densification of Inconel 718. SLPS is sensitive to the feedstock chemistry that has a strong influence on the liquid volume fraction at the processing temperature. Based on these results, we discuss an empirical framework to determine the role of powder particle size and liquid volume fraction on sintering kinetics. In conclusion, the role of powder packing factor and binder saturation on microstructural evolution is discussed. The current challenges in the use of BJ3DP for fabrication of Inconel 718, as well as, extension to other metal systems, are presented.

36 MATERIALS SCIENCE↗

Senary refractory high-entropy alloy HfNbTaTiVZr

Discovery of new single-phase high-entropy alloys (HEAs) is important to understand HEA formation mechanisms. The present study reports computational design and experimental validation of a senary HEA, HfNbTaTiVZr, in a body-centered cubic structure. The phase diagrams and thermodynamic properties of this senary system were modeled using the CALPHAD method. Its atomic structure and diffusion constants were studied using ab initio molecular dynamics simulations. Here, the microstructure of the as-cast HfNbTaTiVZr alloy was studied using X-ray diffraction and scanning electron microscopy, and the microsegregation in the as-cast state was found to qualitatively agree with the solidification predictions from CALPHAD. Supported by both simulation and experimental results, the HEA formation rules are discussed.

36 MATERIALS SCIENCE↗

Process-Structure-Property Relationships for 316L Stainless Steel Fabricated by Additive Manufacturing and Its Implication for Component Engineering

We investigate the process-structure-property relationships for 316L stainless steel prototyping utilizing 3-D laser engineered net shaping (LENS), a commercial direct energy deposition additive manufacturing process. Our study concluded that the resultant physical metallurgy of 3-D LENS 316L prototypes is dictated by the interactive metallurgical reactions, during instantaneous powder feeding/melting, molten metal flow and liquid metal solidification. This study also showed 3-D LENS manufacturing is capable of building high strength and ductile 316L prototypes due to its fine cellular spacing from fast solidification cooling, and the well-fused epitaxial interfaces at metal flow trails and interpass boundaries. However, without further LENS process control and optimization, the deposits are vulnerable to localized hardness variation attributed to heterogeneous microstructure, i.e., the interpass heat-affected zone (HAZ) from repetitive thermal heating during successive layer depositions. Most significantly, the current deposits exhibit anisotropic tensile behavior, i.e., lower strain and/or premature interpass delamination parallel to build direction (axial). This anisotropic behavior is attributed to the presence of interpass HAZ, which coexists with flying feedstock inclusions and porosity from incomplete molten metal fusion. Our current observations and findings contribute to the scientific basis for future process control and optimization necessary for material property control and defect mitigation.

36 MATERIALS SCIENCE↗

Influence of minor Ce additions on magnetic and electrical properties in Fe–6.5 wt. % Si alloy

Fe–6.5 wt. % Si alloys exhibit lower core loss at higher frequency than the dominating electrical steel containing 3.2% Si due to its lower magneto-crystalline anisotropy energy (MAE) and higher electrical resistivity. However, compared to nanocrystalline and amorphous soft-magnetic materials, 6.5% Si steel, although being cost effective and having high saturation magnetization, still has much to improve, especially with respect to MAE and resistivity. To explore further improvement, the effects of minor Ce additions (due to its mixed valence 4f-electron configuration) on the microstructure, electrical and magnetic behaviors of Fe–6.5 wt. % Si alloys were investigated. Due to its limited solubility in Fe, Ce exhibits condition-dependent effects on electrical resistivity, showing only marginal improvement under rapid solidification. In contrast, Ce addition degrades magnetic performance, reducing saturation magnetization (from 1.86 to 1.76 T) and increasing coercivity (from 88 to 171 A/m), which results in an 83.4% increase in core loss (W 10/1000 condition). Overall, Ce addition provides limited benefit in electrical resistivity while deteriorating magnetic properties, making it ineffective for enhancing the soft magnetic performance of Fe–6.5 wt. % Si alloys.

36 MATERIALS SCIENCE↗

Novel Synthesis and Characterization of Uranium-Zirconium Carbonitride by Direct Casting

UZrCN has exhibited thermophysical properties beneficial to high temperature reactor applications such as nuclear thermal rockets. The present work investigates a novel liquid phase synthesis method involving the admission of nitrogen gas during arc melting of uranium, zirconium, and carbon. Initial microstructural examinations using SEM indicated that the samples remain heterogenous with zirconium-rich cores in a uranium-rich matrix. Heterogeneity resulted from large differences in melting temperature of the major constituents and rapid solidification. Additional EDS, combustion analysis, and inert gas fusion analysis proved that the core regions have both uranium and zirconium and establish that carbon and nitrogen are retained during the fabrication process. XRD clarifies that the light elements did not form compounds with the uranium matrix but rather incorporated into the core region forming a sub-stoichiometric UZrCN. Heat treatment performed on equimolar U-Zr-C resulted in an increase in the homogenous phase present with an XRD pattern reflecting a ternary UZrCN despite small amounts of segregation in the final button.

36 - MATERIALS SCIENCE↗