Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SYNGAS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Transformation of Sulfur Species during Steam/Air Regeneration on a Ni Biomass Conditioning Catalyst

Sulfur K-edge XANES identified transformation of sulfides to sulfates during combined steam and air regeneration on a Ni/Mg/K/Al2O3 catalyst used to condition biomass-derived syngas. This catalyst was tested over multiple reaction/regeneration/reduction cycles. Postreaction catalysts showed the presence of sulfides on H2S-poisoned sites. Although H2S was observed to leave the catalyst bed during regeneration, sulfur remained on the catalyst, and a transformation from sulfides to sulfates was observed. Following the oxidative regeneration, the subsequent H2 reduction led to a partial reduction of sulfates back to sulfides, indicating the difficulty and sensitivity in achieving complete sulfur removal during regeneration for biomass-conditioning catalysts.

09 BIOMASS FUELS↗

Novel physical solvents for selective CO{sub 2} capture from fuel gas streams at elevated pressures and temperatures

Three perfluorinated compounds (PFCs), PP10, PP11, and PP25, manufactured by F2 Chemicals Ltd., U.K., were investigated as physical solvents for selective CO{sub 2} capture from synthesis gas or syngas streams at elevated pressures and temperatures. The equilibrium solubility, the hydrodynamic, and the mass-transfer parameters of CO{sub 2} in the solvents were measured in a 4-L ZipperClave agitated reactor under wide ranges of operating conditions: pressures (6-30 bar), temperatures (300-500 K), mixing speeds (10-20 Hz), and liquid heights (0.14-0.22 m). The CO{sub 2} solubilities in the three solvents decreased with an increasing temperature at constant pressure and followed Henry's law. The CO{sub 2} solubilities in PP25 were greater than those in PP10 and PP11. The volumetric liquid-side mass-transfer coefficients (k{sub La}) of CO{sub 2} in the PFCs increased with mixing speed, pressure, and temperature. Also, the gas-liquid interfacial areas of CO{sub 2} in the three PFCs appeared to control the behavior of k{sub La}. This study proved the thermal and chemical stability and the ability of the PFCs to selectively absorb CO{sub 2} at temperatures up to 500 K and pressures as high as 30 bar. A preliminary conceptual process design using PP25 for selective CO{sub 2} capture from hot-shifted gas with pressure-swing and pressure-temperature-swing regeneration options was devised. The pressure-temperature-swing option led to greater PP25 solvent loss but a more favorable (more negative) net enthalpy than the pressure-swing option. However, for either regeneration option to be economically viable, the PP25 solvent must be completely recovered from the process. 109 refs., 9 figs., 14 tabs.

01 COAL, LIGNITE, AND PEAT↗

Improving process performances in coal gasification for power and synfuel production

This paper is aimed at developing process alternatives of conventional coal gasification. A number of possibilities are presented, simulated, and discussed in order to improve the process performances, to avoid the use of pure oxygen, and to reduce the overall CO{sub 2} emissions. The different process configurations considered include both power production, by means of an integrated gasification combined cycle (IGCC) plant, and synfuel production, by means of Fischer-Tropsch (FT) synthesis. The basic idea is to thermally couple a gasifier, fed with coal and steam, and a combustor where coal is burnt with air, thus overcoming the need of expensive pure oxygen as a feedstock. As a result, no or little nitrogen is present in the syngas produced by the gasifier; the required heat is transferred by using an inert solid as the carrier, which is circulated between the two modules. First, a thermodynamic study of the dual-bed gasification is carried out. Then a dual-bed gasification process is simulated by Aspen Plus, and the efficiency and overall CO{sub 2} emissions of the process are calculated and compared with a conventional gasification with oxygen. Eventually, the scheme with two reactors (gasifier-combustor) is coupled with an IGCC process. The simulation of this plant is compared with that of a conventional IGCC, where the gasifier is fed by high purity oxygen. According to the newly proposed configuration, the global plant efficiency increases by 27.9% and the CO{sub 2} emissions decrease by 21.8%, with respect to the performances of a conventional IGCC process. 29 refs., 7 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Evaluation of activated carbon adsorbents for CO{sub 2} capture in gasification

Activated carbon adsorbents have been evaluated at high pressure, up to 4 MPa, to determine their applicability for the removal of CO{sub 2} from syngas generated from gasification. The CO{sub 2} adsorption capacity and diffusion mechanism were demonstrated to be dependent upon the adsorbent outgas conditions. Activated carbons have been demonstrated to have higher adsorption capacities than existing absorption systems up to 12 mmol g{sup -1} at 4 MPa, under strong outgas conditions. Adsorption capacities on a weight basis have been demonstrated to be correlated with the surface area and micropore volume of the materials. However, performance on a volumetric basis is less well-defined and is controlled by the form and bulk density of the adsorbent. Complete cyclic regeneration of the adsorbents has been demonstrated by pressure swing regeneration cycles. 37 refs., 8 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Diesel production from Fischer-Tropsch: the past, the present, and new concepts

Fischer-Tropsch synthesis is technically classified into two categories, the high-temperature Fischer-Tropsch (HTFT) and the low-temperature Fischer-Tropsch (LTFT) processes. The criterion for this classification is the operating temperature of the synthesis, which ranges between 310-340{sup o}C for the HTFT process and 210-260{sup o}C for the LTFT process. A Fischer-Tropsch facility can be divided into roughly three sections, synthesis gas (syngas) generation, FT synthesis, and refining of the synthetic crude (syncrude). Fischer-Tropsch refineries differ regarding the product upgrading, and both transportation fuels and chemicals can be produced. Regarding the FT refinery history, the configuration of each refinery also reflects the requirements of the fuel specification at that time. This paper gives a condensed overview of how Fischer-Tropsch facilities changed during the last 70 years and focuses in particular on the diesel fuel produced. Some conceptual flow schemes are additionally presented with emphasis on the combined upgrading of the high boiling part of the FT product spectrum with liquids derived from coal pyrolysis. 52 refs., 14 figs., 12 tabs.

01 COAL, LIGNITE, AND PEAT↗

An Integrated Approach to Coal Gasifier Testing, Modeling, and Process Optimization

Gasification is an important method of converting coal into clean burning fuels and high-value industrial chemicals. However, gasifier reliability can be severely limited by rapid degradation of the refractory lining in hot-wall gasifiers. The Pacific Northwest National Laboratory (PNNL) is performing multidisciplinary research to provide the experimental data and the engineering models needed to control gasifier operation for extended refractory life. Our experimental program includes prediction of slag viscosity using empirical viscosity models encompassing US coals, characterization of selected slag-refractory interaction including transport of slag/refractory components at the slag-refractory interface, and measurement of slag penetration into refractories as a function of time and temperature. The experimental data is used in slag flow, slag penetration, and refractory damage models to predict the operating temperature limits for increased refractory life. A simplified entrained flow gasifier model is also being developed to simulate one-dimensional axial flow with average axial velocity, coal devolatilization, and combustion kinetics. Combining the slag flow, refractory degradation, and gasifier models will provide a powerful tool to predict the coal and oxidant feed rates and control the gasifier operation to balance coal conversion efficiency with increased refractory life. A research scale gasifier has also been constructed at PNNL to provide syngas for coal conversion and carbon sequestration research, and also valuable datasets on operating conditions for validating the modeling results.

01 COAL, LIGNITE, AND PEAT↗

Screening of binders for pelletization of CaO-based sorbents for CO{sub 2} capture

CaO-based CO{sub 2} looping cycle technology is a promising method for separation of CO{sub 2} from flue gas and syngas at high temperatures. The process of CO{sub 2} capture is expected to take place in fluidized-bed combustion (FBC) systems, which implies significant attrition and elutriation of the solid sorbent. Hence, both reactivation of spent sorbent and preparation of modified CaO-based sorbent may be required to maximize the performance of the sorbent. We present initial results on the screening of suitable binders for pelletization. Two types of bentonite (Na- and Ca-bentonite) and four types of commercial calcium aluminate cements (CA-14, CA-25, Secar 51, and Secar 80) were investigated here, with a primary focus of maintaining a high CO{sub 2}-capture capacity over 30-35 cycles. The tests were carried out using a thermogravimetric analyzer (TGA), and the results showed that the presence of bentonites led to faster decay in activity as a result of the formation of calcium-silica compounds with low melting points, which leads to enhanced sintering. This is confirmed by scanning electron microscopy (SEM) and also X-ray diffraction (XRD), which showed the presence of spurrite (Ca{sub 5}(SiO{sub 4}){sub 2}CO{sub 3}) as the dominant compound in the pellet after this series of cycles. Better results were obtained with no binder, i.e., by hydration of lime, where Ca(OH){sub 2} plays the role of the binder. Promising results were obtained also with calcium aluminate cements, where no effect of sintering because of the presence of these binders was noticed. Thus, on the basis of this study, the use of calcium aluminate cements for pelletization of CaO-based sorbent is recommended. 39 refs., 9 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Nanocomposite oxygen carriers for chemical-looping combustion of sulfur-contaminated synthesis gas

Chemical-looping combustion (CLC) is an emerging technology for clean combustion. We have previously demonstrated that the embedding of metal nanoparticles into a nanostructured ceramic matrix can result in unusually active and sinter-resistant nanocomposite oxygen carrier materials for CLC, which combine the high reactivity of metals with the high-temperature stability of ceramics. In the present study, we investigate the effect of H{sub 2}S in a typical coal-derived syngas on the stability and redox kinetics of Ni- and Cu-based nanostructured oxygen carriers. Both carriers show excellent structural stability and only mildly changed redox kinetics upon exposure to H{sub 2}S, despite a significant degree of sulfide formation. Surprisingly, partial sulfidation of the support results in a strong increase in oxygen carrier capacity in both cases because of the addition of a sulfide-sulfate cycle. Overall, the carriers show great potential for use in CLC of high-sulfur fuels. 21 refs., 13 figs. 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Surface tension measurements of coal ash slags under reducing conditions at atmospheric pressure

The global demand for reduced CO{sub 2} emission from power plants can be answered by coal gasification techniques. To develop integrated gasification combined cycles that incorporate hot syngas cleaning facilities, detailed knowledge of the thermophysical properties of coal ashes is imperative. Currently, the surface tension of liquid coal ash slags in a reducing environment was studied by means of the sessile drop method. Three different algorithms were employed to analyze the acquired drop images. The slags under consideration were obtained from black and brown coals as well as from an experimental gasification reactor. Typically, a sharp surface tension decrease with temperature was found in the melting interval of the ashes. This was followed by a temperature range of smooth drop contours during which a slight rise of the surface tension could mostly be observed. Bubbles at the circumference of the drops started to appear when approaching the measurement temperature limit of 1550{sup o}C. With regard to the temperature regime of uncorrugated drop profiles, coal ash slags exhibited surface tension values between 400 and 700 mN/m. 32 refs., 9 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Effect of fuel gas composition in chemical-looping combustion with Ni-based oxygen carriers. 1. Fate of sulfur

Chemical-looping combustion (CLC) has been suggested among the best alternatives to reduce the economic cost of CO{sub 2} capture using fuel gas because CO{sub 2} is inherently separated in the process. For gaseous fuels, natural gas, refinery gas, or syngas from coal gasification can be used. These fuels may contain different amounts of sulfur compounds, such as H{sub 2}S and COS. An experimental investigation of the fate of sulfur during CH{sub 4} combustion in a 500 W{sub th} CLC prototype using a Ni-based oxygen carrier has been carried out. The effect on the oxygen carrier behavior and combustion efficiency of several operating conditions such as temperature and H{sub 2}S concentration has been analyzed. Nickel sulfide, Ni3S{sub 2}, was formed at all operating conditions in the fuel reactor, which produced an oxygen carrier deactivation and lower combustion efficiencies. However, the oxygen carrier recovered their initial reactivity after certain time without sulfur addition. The sulfides were transported to the air reactor where SO{sub 2} was produced as final gas product. Agglomeration problems derived from the sulfides formation were never detected during continuous operation. Considering both operational and environmental aspects, fuels with sulfur contents below 100 vppm H{sub 2}S seem to be adequate to be used in an industrial CLC plant.

01 COAL, LIGNITE, AND PEAT↗

Underground coal gasification: a brief review of current status

Coal gasification is a promising option for the future use of coal. Similarly to gasification in industrial reactors, underground coal gasification (UCG) produces syngas, which can be used for power generation or for the production of liquid hydrocarbon fuels and other valuable chemical products. As compared with conventional mining and surface gasification, UCG promises lower capital/operating costs and also has other advantages, such as no human labor underground. In addition, UCG has the potential to be linked with carbon capture and sequestration. The increasing demand for energy, depletion of oil and gas resources, and threat of global climate change lead to growing interest in UCG throughout the world. In this article, we review the current status of this technology, focusing on recent developments in various countries.

01 COAL, LIGNITE, AND PEAT↗

SO{sub 2} Retention by CaO-Based Sorbent Spent in CO{sub 2} Looping Cycles

CaO-based looping cycles are promising processes for CO{sub 2} Capture from both syngas and flue gas. The technology is based on cyclical carbonation of CaO and regeneration of CaCO{sub 3} in a dual fluidized-bed reactor to produce a pure CO{sub 2} stream suitable for sequestration. Use of spent sorbent from CO{sub 2} looping cycles for SO{sub 2} capture is investigated. Three limestones were investigated: Kelly Rock (Canada), La Blanca (Spain), and Katowice (Poland, Upper Silesia). Carbonation/calcination cycles were performed in a tube furnace with both the original limestones and samples thermally pretreated for different times (i.e., sintered). The spent sorbent samples were sulfated in a thermogravimetric analyzer (TGA). The changes in the resulting sorbent pore structure were then investigated using mercury porosimetry. It has been shown that the sulfation rates of both thermally pretreated and spent sorbent samples are lower in comparison with those of the original samples. However, final conversions of both spent and pretreated sorbents after longer sulfation time were comparable or higher than those observed for the original sorbents under comparable conditions. Maximum sulfation levels strongly depend on sorbent porosity and pore surface area. The results showed that spent sorbent samples from CO{sub 2} looping cycles can be used as sorbents for SO{sub 2} retention in cases where significant porosity loss does not occur during CO{sub 2} reaction cycles. In the case of spent Kelly Rock and Katowice samples, sorbent particles are practically uniformly sulfated, achieving final conversions that are determined by the total pore volume available for the bulky CaSO{sub 4} product.

01 COAL, LIGNITE, AND PEAT↗

A New Molybdenum Nitride Catalyst with Rhombohedral MoS 2 Structure for Hydrogenation Applications

Nitrogen-rich transition-metal nitrides hold great promise to be the next-generation catalysts for clean and renewable energy applications. However, incorporation of nitrogen into the crystalline lattices of transition metals is thermodynamically unfavorable at atmospheric pressure; most of the known transition metal nitrides are nitrogen-deficient with molar ratios of N:metal less than a unity. In this work, we have formulated a high-pressure route for the synthesis of a nitrogen-rich molybdenum nitride through a solid-state ion-exchange reaction. The newly discovered nitride, 3R-MoN 2 , adopts a rhombohedral R3m structure, isotypic with MoS 2 . Further, this new nitride exhibits catalytic activities that are three times more active than the traditional catalyst MoS 2 for the hydrodesulfurization of dibenzothiophene and more than twice as high in the selectivity to hydrogenation. The nitride is also catalytically active in sour methanation of syngas with >80% CO and H 2 conversion at 723 K. Lastly, our formulated route for the synthesis of 3R-MoN 2 is at a moderate pressure of 3.5 GPa and, thus, is feasible for industrial-scale catalyst production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Methanol Synthesis from H-2 and CO2 on a Mo6S8 Cluster: A Density Functional Study

Catalytic CO{sub 2} hydrogenation to methanol has received considerable attention as an effective way to utilize CO{sub 2}. In this paper, density functional theory was employed to investigate the methanol synthesis from CO{sub 2} and H{sub 2} on a Mo{sub 6}S{sub 8} cluster. The Mo{sub 6}S{sub 8} cluster is the structural building block of the Chevrel phase of molybdenum sulfide, and has a cagelike structure with an octahedral Mo{sub 6} metallic core. Our calculations indicate that the preferred catalytic pathway for methanol synthesis on the Mo{sub 6}S{sub 8} cluster is very different from that of bulklike MoS{sub 2}. MoS{sub 2} promotes the C-O scission of H{sub x}CO intermediates, and therefore, only hydrocarbons are produced. The lower S/Mo ratio for the cluster compared to stoichiometric MoS{sub 2} might be expected to lead to higher activity because more low-coordinated Mo sites are available for reaction. However, our results show that the Mo{sub 6}S{sub 8} cluster is not as reactive as bulk MoS{sub 2} because it is unable to break the C-O bond of H{sub x}CO intermediates and therefore cannot produce hydrocarbons. Yet, the Mo{sub 6}S{sub 8} cluster is predicted to have moderate activity for converting CO{sub 2} and H{sub 2} to methanol. The overall reaction pathway involves the reverse water-gas shift reaction (CO{sub 2} + H{sub 2} {yields} CO + H{sub 2}O), followed by CO hydrogenation via HCO (CO + 2H{sub 2} {yields} CH{sub 3}OH) to form methanol. The rate-limiting step is CO hydrogenation to the HCO with a calculated barrier of +1 eV. This barrier is much lower than that calculated for a comparably sized Cu nanoparticle, which is the prototypical metal catalyst used for methanol synthesis from syngas (CO + H{sub 2}). Both the Mo and S sites participate in the reaction with CO{sub 2}, CO, and CH{sub x}O preferentially binding to the Mo sites, whereas S atoms facilitate H-H bond cleavage by forming relatively strong S-H bonds. Our study reveals that the unexpected activity of the Mo{sub 6}S{sub 8} cluster is the result of the interplay between shifts in the Mo d-band and S p-band and its unique cagelike geometry.

10 SYNTHETIC FUELS↗

To address surface reaction network complexity using scaling relations machine learning and DFT calculations

Surface reaction networks involving hydrocarbons exhibit enormous complexity with thousands of species and reactions for all but the very simplest of chemistries. We present a framework for optimization under uncertainty for heterogeneous catalysis reaction networks using surrogate models that are trained on the fly. The surrogate model is constructed by teaching a Gaussian process adsorption energies based on group additivity fingerprints, combined with transition-state scaling relations and a simple classifier for determining the rate-limiting step. The surrogate model is iteratively used to predict the most important reaction step to be calculated explicitly with computationally demanding electronic structure theory. Applying these methods to the reaction of syngas on rhodium(111), we identify the most likely reaction mechanism. Lastly, propagating uncertainty throughout this process yields the likelihood that the final mechanism is complete given measurements on only a subset of the entire network and uncertainty in the underlying density functional theory calculations.

97 MATHEMATICS AND COMPUTING↗

Cell-free prototyping enables implementation of optimized reverse β-oxidation pathways in heterotrophic and autotrophic bacteria

Abstract Carbon-negative synthesis of biochemical products has the potential to mitigate global CO 2 emissions. An attractive route to do this is the reverse β-oxidation (r-BOX) pathway coupled to the Wood-Ljungdahl pathway. Here, we optimize and implement r-BOX for the synthesis of C4-C6 acids and alcohols. With a high-throughput in vitro prototyping workflow, we screen 762 unique pathway combinations using cell-free extracts tailored for r-BOX to identify enzyme sets for enhanced product selectivity. Implementation of these pathways into Escherichia coli generates designer strains for the selective production of butanoic acid (4.9 ± 0.1 gL −1 ), as well as hexanoic acid (3.06 ± 0.03 gL −1 ) and 1-hexanol (1.0 ± 0.1 gL −1 ) at the best performance reported to date in this bacterium. We also generate Clostridium autoethanogenum strains able to produce 1-hexanol from syngas, achieving a titer of 0.26 gL −1 in a 1.5 L continuous fermentation. Our strategy enables optimization of r-BOX derived products for biomanufacturing and industrial biotechnology.

59 BASIC BIOLOGICAL SCIENCES↗

Dynamic control and quantification of active sites on ceria for CO activation and hydrogenation

Ceria (CeO 2 ) is a widely used oxide catalyst, yet the nature of its active sites remains elusive. This study combines model and powder catalyst studies to elucidate the structure-activity relationships in ceria-catalyzed CO activation and hydrogenation. Well-defined ceria clusters are synthesized on planar CeO 2 (111) and exhibit dynamic and tunable ranges of Ce coordination numbers, which enhance their interaction with CO. Reduced ceria clusters (e.g., Ce 3 O 3 ) bind CO strongly and facilitate its dissociation, while near-stoichiometric clusters (e.g., Ce 3 O 7 ) adsorb CO weakly and promote oxidation via carbonate formation. Unlike planar ceria surfaces, supported ceria clusters exhibit dynamic properties and enhanced catalytic activity, that mimic those of powder ceria catalysts. Insight from model studies provide a method to quantify active sites on powder ceria and guide further optimization of ceria catalysts for syngas conversion. This work marks a leap toward model-guided catalyst design and highlights the importance of site-specific catalysis.

03 NATURAL GAS↗