Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Thermodynamic and kinetic modeling of Mn-Ni-Si precipitates in low-Cu reactor pressure vessel steels

Formation of large volume fractions of Mn-Ni-Si precipitates (MNSPs) causes excess irradiation embrittlement of reactor pressure vessel (RPV) steels at high, extended-life fluences. Thus, a new and unique, semi-empirical cluster dynamics model was developed to study the evolution of MNSPs in low-Cu RPV steels. The model is based on CALPHAD thermodynamics and radiation enhanced diffusion kinetics. The thermodynamics dictates the compositional and temperature dependence of the free energy reductions that drive precipitation. The model treats both homogeneous and heterogeneous nucleation, where the latter occurs on cascade damage, like dislocation loops. The model has only four adjustable parameters that were fit to an atom probe tomography (APT) database. The model predictions are in semi-quantitative agreement with systematic Mn, Ni and Si composition variations in alloys characterized by APT, including a sensitivity to local tip-to-tip variations even in the same steel. The model predicts that heterogeneous nucleation plays a critical role in MNSP formation in lower alloy Ni contents. Single variable assessments of compositional effects show that Ni plays a dominant role, while even small variations in irradiation temperature can have a large effect on the MNSP evolution. Within typical RPV steel ranges, Mn and Si have smaller effects. Furthermore, the delayed but then rapid growth of MNSPs to large volume fractions at high fluence is well predicted by the model. For purposes of illustration, the effect of MNSPs on transition temperature shifts are presented based on well-established microstructure-property and property-property models.

36 MATERIALS SCIENCE↗

Interaction between corrosion crack width and steel loss in RC beams corroded under load

This paper presents results and discussions on an experimental study conducted to relate the rate of widening of corrosion cracks with the pattern of corrosion cracks as well as the level of steel corrosion for RC beams (153 x 254 x 3000 mm) that were corroded whilst subjected to varying levels of sustained loads. Steel corrosion was limited to the tensile reinforcement and to a length of 700 mm at the centre of the beams. The rate of widening of corrosion cracks as well as strains on uncracked faces of RC beams was constantly monitored during the corrosion process, along the corrosion region and along other potential cracking faces of beams using a demec gauge. The distribution of the gravimetric mass loss of steel along the corrosion region was measured at the end of the corrosion process. The results obtained showed that: the rate of widening of each corrosion crack is dependent on the overall pattern of the cracks whilst the rate of corrosion is independent of the pattern of corrosion cracks. A mass loss of steel of 1% was found to induce a corrosion crack width of about 0.04 mm.

36 MATERIALS SCIENCE↗

Corrosion rate of carbon steel in carbonated concrete – A critical review

Reinforced concrete with lower environmental footprint (lower CO{sub 2} emission) can be obtained by reducing the clinker content in the cements. As the carbonation of concrete is faster, corrosion of steel in carbonated concrete during the propagation phase is becoming important both for science and practice. The present literature review summarizes the state of the art, reporting corrosion rate data for a broad range of cement types, w/b ratios and environmental conditions. Correlations between corrosion rate and the main influencing parameters are elaborated and discussed. It confirms that the corrosion rate of steel in carbonated concrete is not under ohmic control. More important are the degree of pore saturation and the effective steel area in contact with water filled pores. It also emerges that the new blended cements have to be systematically studied with respect to the corrosion behavior of steel in carbonated concrete in order to make reliable service life prediction.

36 MATERIALS SCIENCE↗

Joining techniques for a reduced activation 12Cr steel for inertial fusion energy

At Lawrence Livermore National Laboratory, we are developing a reduced activation ferritic martensitic steel that is based on the ferritic martensitic steel HT-9. As a part of the development of this steel, we tested a series of welding processes for characterization, including conventional welds (electron beam, tungsten inert gas, and laser) as well as solid-state welds (hot isostatic pressing). We also heat treated the joints at various temperatures between 750 °C and 1050 °C to find a suitable normalization scheme. The modified HT-9 reduced activation ferritic martensitic steel appears highly suitable to welding and diffusion bonding. All welds showed good quality fusion zones with insignificant cracking or porosity. Additionally, a heat treatment schedule of 950 °C for one hour caused minimal grain growth while still converging the hardness of the base metal with that of the fusion and heat-affected zones. Also, modified HT-9 diffusion bonds that were created at temperatures of at least 950 °C for two hours at 103 MPa had interface tensile strengths of greater than 600 MPa. The diffusion bonds showed no evidence of increased hardness nor void formation at the diffusion bonded interface.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Performance of stainless steel interconnects with (Mn,Co) 3 O 4 -Based coating for solid oxide electrolysis

Mixed transition-metal oxide coatings are commonly applied to stainless steel interconnects for solid oxide cell stacks. Such coatings reduce oxidation and Cr evaporation rates, leading to improved degradation rate and stack lifetime. Here, the ChromLok™ MCO-based composition (Mn,Co) 3 O 4 is applied to Crofer 22 APU stainless steel and evaluated specifically for application in solid oxide electrolyzer stacks operating around 800 °C and utilizing oxygen-ion-conducting solid oxide cells. The MCO coating is found to decrease the stainless steel oxidation rate by about one order of magnitude, and decrease the Cr evaporation rate by fourfold. Furthermore, the coating also dramatically lowers the rate of area-specific resistance increase for stainless steel coupons oxidized for 500 h with constant current applied, from 33 mΩ*cm 2 kh -1 for an uncoated coupon to less than 4 mΩ*cm2 kh -1 for coated coupons. The coating is demonstrated on full-scale interconnects for single-cells, where the coating dramatically reduces degradation rate, and for a stack, which displays stable operation for 700 h.

08 HYDROGEN↗

Quasi-static and dynamic responses of advanced high strength steels: Experiments and modeling

Measured responses of advanced high strength steels (AHSS) and their tailor welded blanks (TWBs), over a wide range of strain-rates (10*4 to 103 s*1) are presented. The steels investigated include transformation induced plasticity (TRIP), dual phase (DP), and drawing quality (DQ) steels. The TWBs include DQ-DQ and DP-DP laser welds. A tensile split Hopkinson pressure bar (SHPB) was used for the dynamic experiments. AHSS and their TWB's were found to exhibit positive strain-rate sensitivity. The Khan-Huang-Liang (KHL) constitutive model is shown to correlate and predict the observed responses reasonably well. Micro-texture characterization of DQ steels, DQ-DQ and DP-DP laser welds were performed to investigate the effect of strain-rate on texture evolution of these materials. Electron backscatter diffraction (EBSD) technique was used to analyze the micro-texture evolution and kernel average misorientation (KAM) map. Measurement of micro-hardness profile across the cross section of tensile samples was conducted to understand the effect of initial microstructure on ductility of laser weld samples.

36 MATERIALS SCIENCE↗

A mesoscale crystal plasticity model to predict room-temperature deformation and martensitic transformation of high-strength Quenching and Partitioning (Q&P) Steels and validation with synchrotron X-ray diffraction

Renowned for the superior mechanical properties and adeptness at cold-forming, Quenching and Partitioning (QP) steels have gained prominence as a promising candidate material in fabricating safety-critical components in various industries. The pertinent research on QP steels focus on the martensitic transformation of the Retained Austenite (RA) phase during cold-forming, a crucial mechanism that substantially influences the overall strength and ductility of QP steels. The austenite stability and transformation rate heavily rely on the local strain path and the initial microstructure, which is challenging for analytical prediction. In this paper, a mesoscale model is developed to capture the deformation and transformation kinetics of QP steels inside the microstructure. The model integrates the detailed explicit microstructure, acquired from characterization experiments, into a high-resolution finite element (FE) mesh. It distinctly model the deformation and interaction between the various phases and the effect on the transformation of RA. The model is validated with high energy X-ray diffraction (HEXRD) data, and shows excellent capability in predicting the asymmetric stress-strain behavior under uniaxial tension and compression, as well as the martensitic transformation rate. The model is used to investigate the strain and load partitioning effect of surrounding matrix to the transformation of RA, offering insights into the complex behavior of QP980 and facilitates further material development.

36 MATERIALS SCIENCE↗

A novel design of transitional layer structure between reduced activation ferritic martensitic steels and tungsten for plasma facing materials

Plasma-facing components (PFCs) are among the most critical gaps for fusion energy to establish technical and economic feasibility. Tungsten as a first wall/blanket material in PFCs requires to be integrating with reduced activation ferritic martensitic (RAFM) steels as a structural component. Currently, major drawbacks are the requirement of brazing, the formation of a brittle interface, and a large difference between the coefficients of thermal expansion of tungsten and steel. Here, a novel transitional multilayer structure was designed and investigated to join tungsten and RAFM steels using three interlayers. The composition of each interlayer was selected based on computational thermodynamics and diffusion kinetics to ensure a body-centered cubic (bcc) single-phase structure and prevent the formation of a brittle intermetallic phase region in the temperature range of 600–1150 °C. Although the transitional layer structure was designed for additive manufacturing, spark plasma sintering (SPS) as proof of concept was used to bond the individual layers. Interfaces were investigated using scanning and transmission electron microscopy methods but no layered intermetallic phase was observed. Nanoindentation maps across the interface suggest major hardness differences at the interface between tungsten and the vanadium interlayer, as well as the interface between RAFM steel and the FeCrAl interlayer.

36 MATERIALS SCIENCE↗

Characterization and mechanical properties of cladded stainless steel 316L with nuclear applications fabricated using electron beam melting

The ability to fabricate or join components of 316 L austenitic stainless steel using additive manufacturing (AM) processes such as laser and electron beam melting (EBM®) offers several advantages including enhanced part complexity, narrow or absent heat affected zones, increased part precision, avoidance of filler materials (such as traditional welds), and the ability to create metallurgically sound bonds. These attributes can contribute to improved mechanical properties of the fabricated components and component repair in nuclear, aerospace, and chemical industries. In the present work, we report that austenitic 316 L stainless steel additively manufactured by EBM exhibits a 76% increase in the yield strength and a corresponding increase of 29% in the ultimate tensile strength in contrast to the wrought substrate and commercial forged 316 L stainless steel. The EBM clad 316 L stainless steel elongation was 36%. The wrought substrate equiaxed grain size was ~30 μm in contrast to elongated, columnar grains ~0.1 mm wide and >1 mm in length for the EBM cladding. Transmission Electron Microscopy (TEM) analysis revealed that these columnar grains, which exhibited very straight, and presumably special grain boundaries having a very high (100) texture, contained a variety of sub-grain microstructures consisting of low-angle sub-grain boundaries containing dislocation tangles and stacking-fault arrays, and homogeneously distributed Cr 23 C 6 carbide precipitates, with no preferential carbide precipitation on either the straight, special columnar grain boundaries, or the very low-angle sub-grain boundaries. This observation and the formation of hierarchical microstructures which produce high strength and possibly corrosion resistance as a consequence of the absence of grain boundary carbide precipitation, illustrate the prospects for AM as a novel concept for achieving grain boundary engineering to promote high-strength and corrosion resistant alloys for high-temperature, corrosive environments, including elevated temperature nuclear reactor applications.

36 MATERIALS SCIENCE↗

Microstructural investigation of an extruded austenitic oxide dispersion strengthened steel containing a carbon-containing process control agent

The adhesion of austenitic oxide dispersion strengthened (ODS) steel during mechanical alloying and a decreased powder production yield can be overcome by the addition of a process control agent: stearic acid. Here, the influence of stearic acid and the introduction of carbon in an extruded and annealed austenitic ODS steel was investigated. In particular the impact of carbon on the precipitate formation, the stability of particle and grain sizes during a heat treatment of 2 h at temperatures in a range between 500 and 1100 °C and the resulting grain size were investigated. No direct influence of carbon on the formation of precipitates was detected in the as-extruded condition. The orientation relationship of oxide nano-particles and the austenitic matrix was found to be size dependent. Also, a surprising growth of oxide precipitates was recorded, which starts at annealing temperatures as low as 700 °C. Precipitates in other steels do not show a growth in this temperature regime at all. For that reason, a possible link between the unexpected growth and the formation of carbides was investigated. M 7 C 3 and M 23 C 6 carbides were found in every sample condition and we were able to show that their amount follows a trend suggested by thermodynamic simulations. The grain size of the extruded austenitic ODS steel was examined and a grain refinement was found after a heat treatment of 2 h at 700 °C or higher was performed. That is caused by the inhabitation of further grain growth after nucleation as part of the recrystallization process has happened. The dragging force exerted by precipitates is strong enough to pin grain boundaries. Furthermore, no direct impact of carbon on the oxide precipitate growth was found, an indirect impact of carbon on the growth of ODS precipitates is supposed but requires long-term annealing studies to be verified.

36 MATERIALS SCIENCE↗

Degradation of impact toughness in cast stainless steels during long-term thermal aging

Cast austenitic stainless steels (CASSs) have been extensively used for the large components of nuclear reactor primary coolant systems. Since the cast steels inevitably contain degradable metastable phases and replacement of the large coolant system components is impractical, the thermal embrittlement of CASS components has been a serious concern in the extended-term operation of nuclear power plants. This study aimed to systematically measure and analyze the effect of long-term thermal aging on the Charpy impact toughness to provide a comprehensive understanding of thermal degradation behavior and a practical aging model to predict the degree of thermal degradation in the cast stainless steels. Additionally, the materials tested in the research include eight CASS alloys (two CF3s, one CF3M, three CF8s, and two CF8Ms) and two reference wrought materials (304L and 316L), in which the nominal δ-ferrite content ranges from ~2% to 33%. These stainless steels have been thermally aged at two light water reactor (LWR) temperatures (290 and 330 °C) and at two accelerated-aging temperatures (360 and 400 °C) for up to 30,000 h; these include both under-aged and over-aged conditions relative to the extended service lifetime (80 years). Charpy impact testing was performed for aged and non-aged specimens, and the impact (absorbed) energy parameters were correlated with a new aging parameter (A). Both the reduction of impact fracture toughness and the shift of ductile-brittle transition temperature were strongly dependent on the δ-ferrite content and degree of thermal aging. A linear relationship was found between the increasing rate of the index transition temperature T 41J and aging parameter A; base on which an empirical model was proposed for prediction of the transition temperature as a simple function of the aging parameter (A) and δ-ferrite content (F). Finally, the critical aging parameter for embrittlement (AC) was evaluated and compared with the existing δ-ferrite content criteria.

36 MATERIALS SCIENCE↗

No ball milling needed: Alternative ODS steel manufacturing with gas atomization reaction synthesis (GARS) and friction-based processing

Oxide dispersion strengthened (ODS) steels are promising structural materials for future fusion reactors. The high-density (~10 23 /m 3 ) of highly stable Y-(Ti)-O nano-oxides provide high sink strength for radiation resistance and high-temperature (> 650 °C) creep strength. Concomitantly, helium management is enabled by trapping high density (~10 23 /m 3 ) of small (< 3 nm) helium bubbles in the vicinity of nano-oxides. However, conventional route of making ODS steels involves prolonged ball milling, canning, degassing, and laborious thermo-mechanical processing (TMP). Such route, especially the batch-by-batch ball milling step, faces persistent challenge with scalability and high costs. Gas atomization reaction synthesis (GARS) method has demonstrated the potential of making precursor ODS steel powders without ball milling, but the nano-oxide density was around 10 21 /m 3 in the final consolidated form by conventional TMP. Taking advantage of GARS precursor powder, we use friction-based processing, including friction consolidation and extrusion, to manufacture ODS steel with further improved nano-oxide characteristics. Here, preliminary results showed that Y/Ti/O species were intimately mixed and rapidly reacted to form nano-oxides with a number density of ~10 22 /m 3 .

36 MATERIALS SCIENCE↗

Cluster dynamics modeling of Mn-Ni-Si precipitates coupled with radiation-induced segregation in low-Cu reactor pressure vessel steels

Formation of precipitates enhanced or induced by irradiation causes hardening and embrittlement of nuclear structural materials. Post-irradiation microstructure characterization of reactor pressure vessel (RPV) steels has shown that precipitation can be strongly associated with radiation-induced segregation (RIS) of solutes on dislocations. However, RIS and precipitation have not been coupled in previous precipitation modeling of RPV steels. Here in this study, a new hybrid and spatially-dependent precipitation model is developed that couples cluster dynamics with RIS, providing an unique way to account for concurrent evolution of heterogeneous cluster densities as well as solute and point defect concentration profiles. The model is applied to study the segregation of Mn, Ni, and Si on dislocations and heterogeneous nucleation of Mn-Ni-Si rich precipitates (MNSPs) in a low-Cu RPV steel. The result shows that the onset of MNSP nucleation on dislocations occurs at the fluence of 2 x 10 23 n.m -2 . The number density and mean radius can reach ~ 10 24 m -3 and 1-2 nm at high fluence, respectively. These observations suggest that the role of RIS and heterogeneous nucleation can be significant for RPV steels under a high fluence of irradiation. Results of simulations adopting various dose rates and dislocation densities show an increased fraction of MNSPs on dislocations at the condition of low dose rate, high dislocation density, and high fluence.

36 MATERIALS SCIENCE↗

Strength and ductility of additively manufactured 316L stainless steel: Impact of neutron irradiation and data variability

Here, this article presents the mechanical properties of additively manufactured (AM) 316L stainless steel processed via the laser powder bed fusion (LPBF) method, focusing on the effects of neutron irradiation on mechanical properties and the variability in strength and ductility data. The rapid melting-solidification process and multiple heating-cooling cycles inherent in LPBF typically result in a fine, metastable microstructure with significant local variability. AM 316L builds of varying thicknesses were fabricated, and SS-J3 miniature tensile specimens were machined from six different locations. These specimens were irradiated with fast neutrons to doses of 2 and 10 dpa at target temperatures of 300 °C and 600 °C. Post-irradiation tensile tests were conducted at room temperature, 300 °C, and 600 °C. Compared to conventional 316L stainless steel, AM 316L exhibited higher initial strength but lower ductility. Irradiation at 300 °C caused significant hardening and prompt necking at yield, with limited uniform ductility, although embrittlement was not observed up to 10 dpa. While neutron irradiation, particularly at 600 °C, increased the variability in strength and ductility data, no clear dependence of mechanical properties on build thickness or sampling location was found—contrary to the conventional perception that AM materials may exhibit high property variability. Furthermore, we observed that the variability in property data for LPBF-processed 316L was relatively low compared to that of wrought 316L stainless steel. This reduced variability in AM 316L steel may be attributed to its highly metastable, stress-containing microstructure, which is discussed in the context of general tensile property variations.

Additively manufactured 316L stainless steel↗

Galvanised steel to aluminium joining by laser and GTAW processes

A new means of assembling galvanised steel to aluminium involving a reaction between solid steel and liquid aluminium was developed, using laser and gas tungsten arc welding (GTAW) processes. A direct aluminium melting strategy was investigated with the laser process, whereas an aluminium-induced melting by steel heating and heat conduction through the steel was carried out with the GTAW process. The interfaces generated during the interaction were mainly composed of a 2-40 {mu}m thick intermetallic reaction layers. The linear strength of the assemblies can be as high as 250 N/mm and 190 N/mm for the assemblies produced respectively by laser and GTAW processes. The corresponding failures were located in the fusion zone of aluminium (laser assemblies), or in the reaction layer (GTAW assemblies)

36 MATERIALS SCIENCE↗

Evolution of secondary phases in austenitic stainless steels during long-term exposures at 600, 650 and 800 deg. C

Three austenitic steels (18Cr-8Ni, 18Cr-10Ni, 21Cr-30Ni), used for long-term applications at temperatures between 600 and 800 deg. C were investigated. In the investigation, metallography, transmission electron microscopy, selected area electron diffraction, energy dispersive X-ray spectroscopy, and scanning electron microscopy were used. In additional to the experimental measurements, thermodynamic predictions were done using the ThermoCalc software and the non-commercial database STEEL16F. Various combinations of M{sub 23}C{sub 6}, sigma, and MC phases were identified in the austenite matrix of these steels. It was confirmed experimentally that extra large particles (up to 10 {mu}m) observed in the 21Cr-30Ni steel are M{sub 23}C{sub 6}, even though this carbide was not predicted as the equilibrium carbide at service temperature (800 deg. C). The analytical-experimental approach, combining thermodynamic predictions and experimental measurements, was found to be reliable for the characterization of austenitic steels.

36 MATERIALS SCIENCE↗

Effect of N{sub 2} + H{sub 2} gas mixtures in plasma nitriding on tribological properties of duplex surface treated steels

Thermo-reactive diffusion chromizing followed by pulsed plasma nitriding were carried out on AISI 52100 and 8620 bearing steels. The chromized samples were pulse-plasma nitrided for 5 h at 500 deg. C in various N{sub 2}-H{sub 2} gas mixtures. The coated steels were characterized using scanning electron microscopy, X-ray diffraction and microhardness testing. The unlubricated wear behaviors of only chromized and duplex treated steels were investigated in ball-on-disc system tests at room temperature. X-ray diffraction patterns of the duplex treated samples containing H{sub 2} indicated the formation of dominant CrN and Cr{sub 2}N nitrides as well as the formation of Cr{sub 3}C{sub 2} and Cr{sub 7}C{sub 3} carbides. Gas mixtures in the plasma nitriding, which was performed after chromizing, have a significant influence on the wear rate of the duplex treated steels. The wear and friction tests showed that the lowest friction coefficient and wear rates were observed for the samples duplex treated in a 50%N{sub 2} +50%H{sub 2} plasma. Conversely, the lowest wear resistance was observed on the samples duplex treated in a gas mixture of 75%N{sub 2} + 25%H{sub 2}, probably due to formation of a hard and brittle layer.

36 MATERIALS SCIENCE↗

Atomic force microscopy applied to the quantification of nano-precipitates in thermo-mechanically treated microalloyed steels

Quantification of nanometer-size precipitates in microalloyed steels has been traditionally performed using transmission electron microscopy (TEM), in spite of its complicated sample preparation procedures, prone to preparation errors and sample perturbation. In contrast to TEM procedures, atomic force microscopy (AFM) is performed on the as-prepared specimen, with sample preparation requirements similar to those for optical microscopy (OM), rendering three-dimensional representations of the sample surface with vertical resolution of a fraction of a nanometer. In AFM, contrast mechanisms are directly related to surface properties such as topography, adhesion, and stiffness, among others. Chemical etching was performed using 0.5% nital, at time intervals between 4 and 20 s, in 4 s steps, until reaching the desired surface finish. For the present application, an average surface-roughness peak-height below 200 nm was sought. Quantification results of nanometric precipitates were obtained from the statistical analysis of AFM images of the microstructure developed by microalloyed Nb and V-Mo steels. Topography and phase contrast AFM images were used for quantification. The results obtained using AFM are consistent with similar TEM reports. - Highlights: Black-Right-Pointing-Pointer We quantified nanometric precipitates in Nb and V-Mo microalloyed steels using AFM. Black-Right-Pointing-Pointer Microstructures of the thermo-mechanically treated microalloyed steels were used. Black-Right-Pointing-Pointer Topography and phase contrast AFM images were used for quantification. Black-Right-Pointing-Pointer AFM results are comparable with traditionally obtained TEM measurements.

36 MATERIALS SCIENCE↗