Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Improved adherence of sputtered titanium carbide coatings on nickel- and titanium-base alloys

Rene 41 and Ti-6Al-4V alloys were radio frequency sputter coated with titanium carbide by several techniques in order to determine the most effective. Coatings were evaluated in pin-on-disk tests. Surface analysis by X-ray photoelectron spectroscopy was used to relate adherence to interfacial chemistry. For Rene 41, good coating adherence was obtained when a small amount of acetylene was added to the sputtering plasma. The acetylene carburized the alloy surface and resulted in better bonding to the TiC coating. For Ti-6Al-4V, the best adherence and wear protection was obtained when a pure titanium interlayer was used between the coating and the alloy. The interlayer is thought to prevent the formation of a brittle, fracture-prone, aluminum oxide layer.

Wheeler, D. R.↗

Surface sticking probabilities for sputtered atoms of Nb-93 and Rh-103

The capture coefficient probabilities for sputtered atoms of Nb-93 and Rh-103 incident on Al2O3 surfaces were measured using the backscattering of MeV heavy ions. In the circumstance where the collecting surface is thickly covered, the sticking probabilities integrated over the energy distribution of sputtered atoms are 0.97 plus or minus 0.01 for Nb-93 and 0.95 plus or minus 0.01 for Rh-103 respectively. In the limit of negligible areal coverage of the collector, the accuracy is less; in this case the sticking probabilities are 0.97 + 0.03 or -0.08 and 0.95 + 0.05 or -0.08.

Weller, M. R.↗

Sputtering in mercury ion thrusters

A model, which assumes that chemisorption is the dominant mechanism, is applied to the sputtering rate measurements of the screen grid of a 30 cm thruster in the presence of nitrogen. The model utilizes inputs from a variety of experimental and analytical sources. The model of environmental effects on sputtering was applied to thruster conditions of low discharge voltage and a discussion of the comparison of theory and experiment is presented.

Mantenieks, M. A.↗

Application of ESCA to the determination of stoichiometry in sputtered coatings and interface regions

X-ray Photoelectron Spectroscopy (XPS) was used to characterize radiofrequency sputter deposited films of several refractory compounds. Both the bulk film properties such as purity and stoichiometry and the character of the interfacial region between the film and substrate were examined. The materials were CrB2, MoS2, Mo2C, and Mo2B5 deposited on 440C steel. It was found that oxygen from the sputtering target was the primary impurity in all cases. Biasing improves the film purity. The effect of biasing on film stoichiometry is different for each compound. Comparison of the interfacial composition with friction data suggests that adhesion of these films is improved if a region of mixed film and iron oxides can be formed.

Wheeler, D. R.↗

An XPS study of the adherence of refractory carbide, silicide, and boride RF-sputtered wear-resistant coatings

Radio frequency sputtering was used to deposit refractory carbide, silicide, and boride coatings on 440-C steel substrates. Both sputter etched and pre-oxidized substrates were used and the films were deposited with and without a substrate bias. The composition of the coatings was determined as a function of depth by X-ray photoelectron spectroscopy combined with argon ion etching. Friction and wear tests were conducted to evaluate coating adherence. In the interfacial region there was evidence that bias may produce a graded interface for some compounds. Biasing, while generally improving bulk film stoichiometry, can adversely affect adherence by removing interfacial oxide layers. Oxides of all film constituents except carbon and iron were present in all cases but the iron oxide coverage was only complete on the preoxidized substrates. The film and iron oxides were mixed in the MoSi2 and Mo2C films but layered in the Mo2B5 films. In the case of mixed oxides, preoxidation enhanced film adherence. In the layered case it did not.

Brainard, W. A.↗

Use of a nitrogen-argon plasma to improve adherence of sputtered titanium carbide coatings on steel

Friction and wear experiments on 440-C steel surfaces that had been RF-sputtered with titanium carbide when a small percentage of nitrogen was added to the plasma were conducted. X-ray photoelectron spectroscopy and X-ray diffraction were used to analyze the resultant coatings. Results indicate that a small partial pressure of nitrogen (about 0.5%) markedly improves the adherence, friction, and wear properties when compared with coatings applied on sputter-etched oxidized surfaces or in the presence of a small oxygen partial pressure. The improvements are related to the formation of an interface containing a mixture of the nitrides of titanium and iron, which are harder than their corresponding oxides.

Brainard, W. A.↗

Energy spectrum of sputtered uranium - A new technique

The fission track technique for detecting U-235 has been used in conjunction with a mechanical time-of-flight spectrometer in order to measure the energy spectrum in the region 1 eV to 1 keV of material sputtered from a 93% enriched U-235 foil by 80 keV Ar-40(+) ions. The spectrum was found to exhibit a peak in the region 2-4 eV and to decrease approximately as E exp -1.77 for E not less than 100 eV. The design, construction and resolution of the mechanical spectrometer are discussed and comparisons are made between the data and the predictions of the random collision cascade model of sputtering.

Weller, R. A.↗

Localized deposition and sputtering of Jovian ionospheric sodium on Io

Because of relative motion between the innermost Galilean satellite Io and Jupiter's ionosphere, a current is drawn from the ionosphere that can be a source of both deposition on, and sputtering from, the surface of Io. It is shown that the ions in this current strike Io in a localized region in the quadrant bounded by a line connecting Io and Jupiter and a tangent line extended in the direction of Io's orbital motion. If these ions are the principal source of sodium that is sputtered from Io, then this current provides a simple explanation of the observation of a localized area from which sodium ions escape from Io. The geometry of this current may also affect the optical surface of Io. Several experimental tests are suggested that can determine the compatibility of this hypothesis with the directly observable properties of Io's surface.

Hill, T. W.↗

Mass effects on angular distribution of sputtered atoms

Sputtering metal targets at low ion energies (Hg or Ar at less than 300 eV) under normal ion incidence causes the lighter atoms (lighter isotopes or lighter elements of alloys) to be preferentially ejected in a direction normal to the target surface. Experimental results are shown for several elements and alloys at various bombardment energies. The amount of enrichment of the lighter species normal to the target surface decreases quite rapidly with increasing ion energy. The phenomenon is a result of reflective collisions because lighter atoms can be backscattered from heavier ones underneath but not vice versa. The effect provides an explanation of why solar-wind-exposed lunar material is enriched in the heavier isotopes, since sputtered lower-mass elements have a higher chance of achieving the lunar escape velocity.

Olson, R. R.↗

Tribological properties of sputtered MoS2 films in relation to film morphology

Thin sputter-deposited MoS2 films with thicknesses ranging from 2000 to 6000 A have shown excellent lubricating properties when sputtering parameters and substrate conditions are properly selected and controlled. The lubricating properties are strongly influenced by the crystalline-amorphous structure, morphology, and composition of the films. The coefficient of friction can range from 0.04 (which is effective lubrication) to 0.4 (no lubricating action).

Spalvins, T.↗

Ion beam sputter etching of orthopedic implanted alloy MP35N and resulting effects on fatigue

The effects of two types of argon ion sputter etched surface structures on the tensile stress fatigue properties of orthopedic implant alloy MP35N were investigated. One surface structure was a natural texture resulting from direct bombardment by 1 keV argon ions. The other structure was a pattern of square holes milled into the surface by a 1 keV argon ion beam through a Ni screen mask. The etched surfaces were subjected to tensile stress only in fatigue tests designed to simulate the cyclic load conditions experienced by the stems of artificial hip joint implants. Both types of sputter etched surface structures were found to reduce the fatigue strength below that of smooth surface MP35N.

Wintucky, E. G.↗

Electron reflection and secondary emission characteristics of sputter-textured pyrolytic graphite surfaces

Low secondary and reflected primary electron emission from the collector electrode surfaces is important for optimum collector efficiency and hence for high overall efficiency of microwave amplifier tubes used in communication satellites and in military systems. Ion sputter texturing of the surface effectively suppresses electron emission from pyrolytic graphite, which is a promising collector electrode material. Secondary and reflected primary electron emission characteristics of sputter textured pyrolytic graphite surfaces with microstructures of various sizes and densities are presented. The microstructure with the lowest electron emission levels, less than those of soot, consists of a dense array of tall, thin spires.

Wintucky, E. G.↗

Some properties of RF sputtered hafnium nitride coatings

Hafnium nitride coatings were deposited by reactive RF sputtering from a hafnium target in nitrogen and argon gas mixtures. The rate of deposition, composition, electrical resistivity and complex index of refraction were investigated as a function of target substrate distance and the fraction nitrogen, (fN2) in the sputtering atmosphere. The relative composition of the coatings is independent on fN2 for values above 0.1. The electric resistivity of the hafnium nitride films changes over 8 orders of magnitude when fN2 changes from 0.10 to 0.85. The index of refraction is almost constant at 2.8(1-0.3i) up to fN2 = 0.40 then decreases to 2.1(1 - 0.01i) for higher values of fN2.

Aron, P. R.↗

Evaluation of left ventricular assist device pump bladders cast from ion-sputtered polytetrafluorethylene mandrels

A highly thromboresistant blood contacting interface for use in implanatable blood pump is investigated. Biomaterials mechanics, dynamics, durability, surface morphology, and chemistry are among the critical consideration pertinent to the choice of an appropriate blood pump bladder material. The use of transfer cast biopolymers from ion beam textured surfaces is investigated to detect subtle variations in blood pump surface morphology using Biomer as the biomaterial of choice. The efficacy of ion beam sputtering as an acceptable method of fabricating textured blood interfaces is evaluated. Aortic grafts and left ventricular assist devices were implanted in claves; the blood interfaces were fabricated by transfer casting methods from ion beam textured polytetrafluorethylene mandrels. The mandrels were textured by superimposing a 15 micron screen mesh; ion sputtering conditions were 300 volts beam energy, 40 to 50 mA beam, and a mandrel to source distance of 25 microns.

Source record↗

A sputtered zirconia primer for improved thermal shock resistance of plasma-sprayed ceramic turbine seals

It is shown that the application of sputtered Y2O3-stabilized ZrO2 (YSZ) primer in plasma-sprayed YSZ ceramic-coated turbine blades results in an improvement, by a factor of 5-6, in the thermal shock life of specimens with a sprayed, porous, Ni-Cr-Al-Y intermediate layer. Species with and without the primer were found to be able to survive 1000 cycles when the intermediate layer was used, but reduced laminar cracking was observed in the specimen with the primer. It is suggested that the sputtered YZS primer-induced properties are due to (1) more effective wetting and adherence of the plasma-sprayed YZS particles to the primer, and (2) the primer's retardation of impinging, molten plasma sprayed particles solidification rates, which result in a less detrimental residual stress distribution.

Bill, R. C.↗

RF sputtered silicon and hafnium nitrides: Properties and adhesion to 440C stainless steel

Silicon nitride and hafnium nitride coatings were deposited by reactive RF sputtering on oxidized and unoxidized 440C stainless steel substrates. Sputtering was done in mixtures of argon and nitrogen gases from pressed powder silicon nitride and from hafnium metal targets. Depositions were at two background pressures, 8 and 20 mtorr, and at two different fractions (f) of nitrogen in argon, 0.25 and 0.60, for hafnium nitride and at f = 0.25 for silicon nitride. The coatings and the interface between the coating and substrates were investigated by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis and Auger electron spectroscopy. A Knoop microhardness of 1650 + or - 100 kg/sq mm was measured for hafnium nitride and 3900 + or - 500 kg/sq mm for silicon nitride. The friction coefficients between a 440C rider and the coatings were measured under lubricated conditions. Scratch test results demonstrate that the adhesion of hafnium nitride to both oxidized and unoxidized 440C is superior to that of silicon nitride. Oxidized 440C is found to have increased adhesion, to both nitrides, over that of unoxidized 440C.

Grill, A.↗

Photovoltaic properties of ferroelectric BaTiO3 thin films RF sputter deposited on silicon

Ferroelectric thin films of BaTiO3 have been successfully deposited on n-type silicon substrates at temperatures above 500 C by RF sputtering in an O2/Ar atmosphere. Analysis by X-ray diffraction patterns show that films deposited at room temperature are amorphous. At temperatures above 500 C, crystalline BaTiO3 films with a tetragonal structure are obtained. The polarization-electric field (P-E) hysteresis loops and a broad peak in the dielectric constant versus temperature curve at Curie point indicate that the RF sputtered BaTiO3 films are ferroelectric. An anomalous photovoltaic effect is observed in these thin films which is related to the remanent polarization of the material. The results on open-circuit and short-circuit measurements provide an important basis for a better understanding of the role of photovoltaic field, photovoltaic current, and the pyroelectric properties in photoferroelectric domain switching.

Dharmadhikari, V. S.↗

Sputtering of silicon and its compounds in the electronic stopping region

Silicon, silicon dioxide, and silicon nitride have been sputtered with chlorine ions at 5 MeV and 20 MeV. While the yield from the silicon target was unmeasurably low, the insulating compounds exhibited the enhanced yields observed in other insulating targets. The yield follows the electronic stopping power and seems to be independent of the target's thermal properties. Some of the data suggest that the enhanced sputtering mechanism may be active in extremely thin films (not less than 3 monolayers).

Qiu, Y.↗