Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RUPTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Study on the Reliability of Carbon Nanotube-Reinforced Sn-58Bi Lead-Free Solder Joints

The wettability, microstructure and mechanical properties of multi-walled carbon nanotube (CNT)-reinforced Sn-58Bi composite solder joints were investigated. The results indicate that the wettability of the Sn-58Bi solder is improved and the growth of interfacial intermetallic (IMC) compounds for solder joints is restrained by CNTs. The thickness of the IMC layers is decreased with increasing CNTs concentration. The microstructure of the Sn-58Bi composite solders is refined, the maximum tensile strength and shear strength are obtained by adding the optimum CNTs content about 0.01 wt.%. However, excessive content of CNTs addition can deteriorate the properties. The creep rupture life of Sn-58Bi solder joint and Sn-58Bi-0.01CNTs solder joint is decreased with increasing load, temperature and current density. The average creep rupture life of Sn-58Bi-0.01CNTs composite solder joint is 60% higher than that of the plain solder joint.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Oxidized low density lipoprotein increases RANKL level in human vascular cells. Involvement of oxidative stress

Highlights: •Oxidized LDL enhances RANKL level in human smooth muscle cells. •The effect of OxLDL is mediated by the transcription factor NFAT. •UVA, H{sub 2}O{sub 2} and buthionine sulfoximine also increase RANKL level. •All these effects are observed in human fibroblasts and endothelial cells. -- Abstract: Receptor Activator of NFκB Ligand (RANKL) and its decoy receptor osteoprotegerin (OPG) have been shown to play a role not only in bone remodeling but also in inflammation, arterial calcification and atherosclerotic plaque rupture. In human smooth muscle cells, Cu{sup 2+}-oxidized LDL (CuLDL) 10–50 μg/ml increased reactive oxygen species (ROS) and RANKL level in a dose-dependent manner, whereas OPG level was not affected. The lipid extract of CuLDL reproduced the effects of the whole particle. Vivit, an inhibitor of the transcription factor NFAT, reduced the CuLDL-induced increase in RANKL, whereas PKA and NFκB inhibitors were ineffective. LDL oxidized by myeloperoxidase (MPO-LDL), or other pro-oxidant conditions such as ultraviolet A (UVA) irradiation, incubation with H{sub 2}O{sub 2} or with buthionine sulfoximine (BSO), an inhibitor of glutathione synthesis{sub ,} also induced an oxidative stress and enhanced RANKL level. The increase in RANKL in pro-oxidant conditions was also observed in fibroblasts and endothelial cells. Since RANKL is involved in myocardial inflammation, vascular calcification and plaque rupture, this study highlights a new mechanism whereby OxLDL might, by generation of an oxidative stress, exert a deleterious effect on different cell types of the arterial wall.

60 APPLIED LIFE SCIENCES↗

A novel indirect tensile test method to measure the biaxial tensile strength of concretes and other quasibrittle materials

A novel indirect tensile test method, the biaxial flexure test (BFT) method, has been developed to measure the biaxial tensile strength of concretes. The classical modulus of rupture (MOR) test has been generalized to three dimensions. In this method, we use a circular plate as the new test specimen. This plate is supported by an annular ring. We apply an external load to this specimen through a circular edge. The centers of the specimen, the loading device and the support are identical. The biaxial tensile strength measured by this new method is about 19% greater than the uniaxial tensile strength obtained from the classical modulus of rupture test as reported by other researchers. However, at the same time, we also found that the stochastic deviation of the biaxial tensile strength is about 63% greater than the uniaxial strength.

36 MATERIALS SCIENCE↗

Piezoelectric response and failure behavior of cement paste under external loading

We study the elastic behavior and rupture mechanism of Calcium Silicate Hydrates (C-S-H) in response to tensile loading. For the three tensile axes, initial defects are spotted in the interlayer regions. However, the crack propagation is rather different depending on the axis of tensile. The cup-and-cone failure surface shows the ductile feature of C-S-H in the x and y directions; while the devastating rupture mode confirms the brittle feature of C-S-H in the z direction. Piezoelectricity was investigated using the charge fluctuation method. The polarization variation in response to small strain was also investigated and piezoelectric coefficients were derived. Furthermore, dependence of elastic and piezoelectric properties over external pressure was analyzed. Results reveal an improvement of the mechanical properties and the ultimate strength especially in the z direction; whereas the non-piezoelectricity remains unchanged despite the rearrangement of atoms induced by the external applied pressure.

36 MATERIALS SCIENCE↗

Pathways of Barotrauma in Juvenile Salmonids Exposed to Simulated Hydroturbine Passage: Boyle’s Law vs. Henry’s Law

On their seaward migration, juvenile salmonids commonly pass hydroelectric dams. Fish passing by the turbine blade may experience rapid decompression, the severity of which can be highly variable and may result in a number of barotraumas. The mechanisms of these injuries can be due to expansion of existing bubbles or gases coming out of solution; governed by Boyle’s Law and Henry’s Law, respectively. This paper combines re-analysis of published data with new experiments to gain a better understanding of the mechanisms of injury and mortality for fish experiencing rapid decompression associated with hydroturbine passage. From these data it appears that the majority of decompression related injuries are due to the expansion of existing bubbles in the fish, particularly the expansion and rupture of the swim bladder. This information is particularly useful for fisheries managers and turbine manufacturers, demonstrating that reducing the rate of swim bladder ruptures by reducing the frequency of occurrence and severity of rapid decompression during hydroturbine passage could reduce the rates of injury and mortality for hydroturbine passed juvenile salmonids.

13 HYDRO ENERGY↗

The effect of rapid and sustained decompression on barotrauma in juvenile brook lamprey and Pacific lamprey: implications for passage at hydroelectric facilities

Fish passing downstream through hydroelectric facilities may pass through hydroturbines where they experience a rapid decrease in barometric pressure as they pass by turbine blades, which can lead to barotraumas including swim bladder rupture, exopthalmia, emboli, and hemorrhaging. In juvenile Chinook salmon, the main mechanism for injury is thought to be expansion of existing gases (particularly those present in the swim bladder) and the rupture of the swim bladder ultimately leading to exopthalmia, emboli and hemorrhaging. In fish that lack a swim bladder, such as lamprey, the rate and severity of barotraumas due to rapid decompression may be reduced however; this has yet to be extensively studied. Another mechanism for barotrauma can be gases coming out of solution and the rate of this occurrence may vary among species. In this study, juvenile brook and Pacific lamprey acclimated to 146.2 kPa (equivalent to a depth of 4.6 m) were subjected to rapid (<1 sec; brook lamprey only) or sustained decompression (17 minutes) to a very low pressure (13.8 kPa) using a protocol previously applied to juvenile Chinook salmon. No mortality or evidence of barotraumas, as indicated by the presence of hemorrhages, emboli or exopthalmia, were observed during rapid or sustained decompression, nor following recovery for up to 120 h following sustained decompression. In contrast, mortality or injury would be expected for 97.5% of juvenile Chinook salmon exposed to a similar rapid decompression to these very low pressures. Additionally, juvenile Chinook salmon experiencing sustained decompression died within 7 minutes, accompanied by emboli in the fins and gills and hemorrhaging in the tissues. Thus, juvenile lamprey may not be susceptible to barotraumas associated with hydroturbine passage to the same degree as juvenile salmonids, and management of these species should be tailored to their specific morphological and physiological characteristics.

13 HYDRO ENERGY↗

Combination Treatment of Hydrogen Peroxide and X-Rays Induces Apoptosis in Human Prostate Cancer PC-3 Cells

Purpose: To study the effect of hydrogen peroxide (H{sub 2}O{sub 2}) on radiation-induced apoptosis in human prostate cancer PC-3 cells. Methods and Materials: At 4h before the irradiation, PC-3 cells were exposed to 10mM ammonium chloride (NH{sub 4}Cl) concentrations. Subsequently, cells were exposed to 0.1mM H{sub 2}O{sub 2} just before the irradiations, which were administered with 10-MV X-rays at doses of 10Gy. Results: The percentage of apoptotic cells at 48h after X-irradiation alone, H{sub 2}O{sub 2} alone, and combined X-irradiation and H{sub 2}O{sub 2} was 1.85%, 4.85%, and 28.4%, respectively. With use of combined X-irradiation and H{sub 2}O{sub 2}, production of reactive oxygen species (ROS) occurred 4h after the irradiation. This resulted in lysosomal rupturing, mitochondrial fragmentation, and the release of cytochrome c into the cytoplasm from the mitochondria. In contrast, when cells were exposed to NH{sub 4}Cl before the X-irradiation and H{sub 2}O{sub 2} administration, apoptosis was almost completely suppressed, ROS production did not occur, lysosomal rupture and mitochondrial fragmentation were blocked, and cytochrome c was not released. Conclusions: Hydrogen peroxide strongly enhanced lysosome-dependent radiation-induced apoptosis in human prostate cancer PC-3 cells. A combined use of X-rays and H{sub 2}O{sub 2} can also injure the mitochondrial cytoplasmic organelles and lead to the production of ROS that in and of itself might possibly induce apoptosis.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Effect of molybdenum content on the microstructure and mechanical properties of ultra-fine Ti(C, N) based cermets

Effect of molybdenum as a sintering aid on the microstructure and mechanical properties of Ti(C, N)-20WC-15Co-Mo-2.5C system cermets was studied in this work. Ti(C, N)-based cermets with variable Mo content were fabricated by conventional powder metallurgy techniques. The microstructure was investigated by means of X-ray diffractometer, scanning electron microscopy in combination with an energy dispersive spectrometer. Mechanical properties such as transverse rupture strength, fracture toughness and hardness were also measured, respectively. Results revealed that finer grains, as well as larger amount of bright core/grey shell structures could be obtained by increasing the molybdenum content. Transverse rupture strength and hardness were also improved. Fracture toughness, however, was decreased with the increase of Mo content. The optimized content of Mo was chosen as 15 wt.% for Ti(C, N)-20WC-15Co-Mo-2.5C system cermets.

36 MATERIALS SCIENCE↗

FIB–SEM tomography of 4th generation PWA 1497 superalloy

The effect of creep deformation on the microstructure of the PWA 1497 single crystal Ni-base superalloy developed for turbine blade applications was investigated. The aim of the present study was to characterize quantitatively a superalloy microstructure and subsequent development of rafted γ′ precipitates in the PWA 1497 during creep deformation at 982 °C and 248 MPa up to rupture. The PWA1497 microstructure was characterized by scanning electron microscopy and FIB–SEM electron tomography. The 3D reconstruction of the PWA1497 microstructure is presented and discussed. - Highlights: • The microstructure of PWA1497 superalloy was examined using FIB–SEM tomography. • In case of modern single crystal superalloys, measurements of A{sub A} are adequate for V{sub V}. • During creep the γ channel width increases from 65 to 193 nm for ruptured specimen. • Tomography is a useful technique for quantitative studies of material microstructure.

36 MATERIALS SCIENCE↗

Preparation of amine-impregnated silica foams using agar as the gelling agent

In this work we successfully prepared amine-impregnated gel-cast silica foams using agar and atmospheric air as the gelling agent and heat treatment atmosphere, respectively. The concentration of 3,6-anhydrogalactose in agar was evaluated by ultraviolet–visible spectroscopy (UV–Vis). The obtained foams were examined by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG) coupled to mass spectrometry (TG-MS), scanning electron microscopy (SEM), X-ray microtomography (micro-CT), and Archimedes method. The cold crushing strength of the materials prepared in this work was assessed using a mechanical testing stage available in the micro-CT system. The obtained foams exhibited a highly interconnected pore network, with an expressive presence of open pores. Samples heat-treated at 1300 °C for 2 h showed both an expressive porosity (≈ 77%) and a significant cold crushing strength (≈ 1.4 MPa). It was observed that the calcination of the prepared materials at 1200 °C for times as long as 16 h may lead to the rupture of pore walls. FTIR and TG-MS revealed that amine groups were properly incorporated into the foams structure. - Highlights: •Successful preparation of amine-impregnated gel-cast silica foams •Agar used as the gelling agent •Samples with expressive porosity and cold crushing strength •Sintering times as long as 16 h led to the rupture of the pore network.

36 MATERIALS SCIENCE↗

Negative influence of rafted γ′ phases on 750 °C/750 MPa creep in a Ni-based single crystal superalloy with 4% Re addition

Highlights: • The negative influence of the rafted γ′ phases on creep was investigated. • The rafted sample exhibited a lower creep rate a shorter rupture life. • Fine γ′ phases impeded first the dislocation movement in γ matrix. • Existed superdislocations and the stress release decreased the creep resistance. • Rafted γ′ phases were more easily cut by superdislocations and stacking faults. - Abstract: Specimens with two different γ′ phase microstructures, named as-heat treated sample with cuboidal γ′ phases and pre-rafted sample with N-type rafted γ′ phases, were compared to investigate the negative influence of the rafted γ′ phases on the creep property in a Ni-based single crystal superalloy with 4% Re addition at 750 °C and 750 MPa condition. The results indicated that the sample with cuboidal γ′ phases exhibited a lower creep rate and a longer rupture life compared to that with rafted γ′ phases. Transmission electron microscope examinations showed that lots of fine γ′ phases impeded first the dislocation movement in the channel of γ matrix in the initial primary creep stage before the cuboidal γ′ phases were cut by stacking faults in as-heat treated sample. However, in pre-rafted sample, some existed superdislocations located in rafted γ′ phases and the mismatch stress release at γ/rafted γ′ interface resulting from pre-rafted treatment not only decreased the creep resistance of rafted γ′ phases, but also weakened the γ/rafted γ′ interface pinning effect for dislocation movement. Therefore, the rafted γ′ phases were easily cut by superdislocations and stacking faults resulting in a higher creep rate and a shorter creep life.

36 MATERIALS SCIENCE↗

Peak Ground Displacement Saturates Exactly When Expected: Implications for Earthquake Early Warning

The scaling of rupture properties with magnitude is of critical importance to earthquake early warning (EEW) systems that rely on source characterization using limited snapshots of waveform data. ShakeAlert, a prototype EEW system that is being developed for the western United States, provides real-time estimates of earthquake magnitude based on P-wave peak ground displacements calculated at stations triggered by the event. The algorithms used in ShakeAlert assume that the displacement measurements at each station are statistically independent and that there exists a linear and time-independent relation between log peak ground displacement and earthquake magnitude. Here we challenge this basic assumption using the largest dataset assembled for this purpose to date: a comprehensive database of more than 140,000 vertical-component waveforms from M4.5–M9 earthquakes occurring near Japan from 1997 through 2018 and recorded by the K-NET and KiK-net strong-motion networks. By analyzing the time-evolution of P-wave peak ground displacements for these earthquakes, we show that there is a break, or saturation, in the magnitude-displacement scaling that depends on the length of the measurement time window. We demonstrate that the magnitude at which this saturation occurs is well-explained by a simple and non-deterministic model of earthquake rupture growth. We then utilize the predictions of this saturation model to develop a Bayesian framework for estimating posterior uncertainties in real-time magnitude estimates.

58 GEOSCIENCES↗

Centrifugal Casting Features/Metallurgical Characterization of Aluminum Alloys

This paper deals with the study of centrifugal effects on aluminium castings under high G values. Most of the studies in this domain (FGMs obtained by centrifugal casting) deal with functionally graded composites reinforced with a solid phase such as silicon particles or others. However, in this study it will be shown that unreinforced aluminium alloys may be significantly influenced by the centrifugal effect and that functionally graded castings are also obtained. It has been observed that the centrifugal effect may increase in some alloys, depending on the relative position in the castings, the rupture strength by approx. 50%, and rupture strain by about 300%, as compared to the gravity casting technique. The Young's modulus may also increase by about 20%. It has also been reported that in vertical centrifugal castings there are mainly three aspects that affect the components thus obtained, namely: fluid dynamics; vibration (inherent to the system); and centrifugal force. These features have a different effect on the castings depending on the aluminium alloy. In this paper, an analysis of the most important effects of the centrifugal casting process on metallurgical features is conducted. A solidification characterization at several points along the mould will be made in order to have an accurate idea of both the fluid dynamics inside the mould during the casting and the solidification behavior in different parts of the component. These two analyses will be related to the metallurgical properties (phase distribution; SDAS; eutectic silicon content and shape, pores density and shape) along the component and mainly along the direction of the centrifugal pressure. A comparison between castings obtained by both centrifugal casting technique and gravity casting technique is made for reference (gravity casting)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Low-Frequency Seismic Ground Motion At The Pier Positions Of The Planned Messina Straits Bridge For A Realistic Earthquake Scenario

We estimated longer-period (period T>0.5 s) components of the ground motion at the piers of the planned Messina straits bridge. As the shortest fault-to-site distance is only 3-5 km, the kinematic earthquake rupture process has to be described in a realistic way and thus, the causative fault is represented by a dense grid of subfaults. To model the 1908 event, we assume a Mw = 7 earthquake, with a 40x20 km rectangular fault, and pure reverse dip-slip. The horizontal upper side of the rectangle is at 3-km depth, and the N corner of the rectangle is just between the piers. For the fault nucleation point, the least favorable place is assumed and a randomized rupture velocity is used in a particular run. In a typical simulation, the fault motion is initially represented by the time history of slip in each of the subfaults and by the distribution of the final seismic moment among the subsources (forming 'asperities'), both generated as lognormal random functions. The time histories are then filtered in order to fit a chosen source spectral model. The parameters that are conditioning the random functions can be based on the bulk of published fault inversions, or reproduced from an earlier successful attempt to simulate ground motions in the epicentral zone of the 1994, M = 6.7 Northridge, California, earthquake. In the second step of calculations, the Green functions (for each subfault and pier combination) are calculated for a layered halfspace model of the pier foundation stratigraphy, using an advanced Green function calculator, that allows an accurate calculation over the entire relevant frequency band including static terms. Finally, the 3-components of the strong ground motion are obtained at the two piers through convolution and summation over the different subsources. We compare a set of response horizontal velocity spectra (PRV) obtained from our calculations with a reference PRV that is considered as a reasonable upper bound for the possible ground motion near the piers. Our results suggest that the seismic ground motion under Torre Sicilia dominates over this under Torre Calabria and that the median (average log) PRV is generally above the reference one, about 1.1-1.3 times for T>4 s, and up to 2 times for 1<T{<=}4 s. The use of advanced fault and medium models, accounting also for the natural scatter of individual PRV due to events with the same gross source parameters, provides a sound basis for the deterministic engineering estimates of future seismic ground motion.

58 GEOSCIENCES↗

A View of Compatible Heat-Resistant Alloy and Coating Systems at High-Temperatures

Conventional and advanced coatings were reviewed, and it was pointed out that the coated Ni-base superalloys decreased their creep rupture life significantly at higher temperatures, and the advanced high strength superalloy became more remarkably. Concept of diffusion barrier coating system (DBC system) and their formation process was introduced, and the results obtained for several heat-resistant alloys, stainless steel (SUS310S), Ni-Mo base alloy (Hastelloy-X), and 4{sup th} generation single crystal superalloy (TMS-138) were given. It was noted that creep-rupture life of the SUS310S and Hastelloy-X with the DBC system became longer than those of the bare alloys with or without conventional {beta}-NiAl coatings. This is due to slow creep-deformation of the Re-base alloy layer as the diffusion barrier. A novel concept based on combination of superalloys and coatings was proposed, by taking both the materials science and corrosion science into consideration.

36 MATERIALS SCIENCE↗

RELIABLE RADIOGRAPHIC INSPECTION OF FLEXIBLE RISERS FOR THE OIL INDUSTRY

Flexible risers are composite tubular structures manufactured by the concentric assemblage of cylindrical polymeric and helically wound metallic layers employed to convey pressurized fluids such as oil, gas and water in the ocean environment. The metallic layers account for the flexible risers' structural strength and are dimensioned according to the static and dynamic loads. They are usually installed in a free hanging catenary configuration and are subjected to the direct action of waves and marine currents and wave induced motions from the oil production platform. The fatigue rupture of wire armours in the end fitting or within the riser segment protected by the bend stiffener is an object of major concern. Integrity models have been developed, however inspection techniques are mandatory to ensure that failure is detected. Gammagraphy has been used as a common inspection technique in all regions of the flexible riser, mainly with the single wall-single view method. On the other side, there is not any qualified radiographic procedure to this kind of structure. Radiographic simulation was adopted and its validation with actual gammagraphies and establishment of radiographic parameters to complex radiation geometries were done. Results show the viability of the radiographic inspection analyzing the armour wires' rupture and the displacement between wires.

36 MATERIALS SCIENCE↗

Tensile and Creep Behavior of Extruded AA6063/SiC{sub p} Al MMCs

Composites of AA6063 Al alloy reinforced with SiC particles (SiC{sub p}) were prepared by the vortex method. Hot extrusion was carried out for the as cast composites with a reduction in area of 25%. Tensile and creep behavior of as-cast and extruded composites were studied at elevated temperatures. Tensile tests carried out at room temperature showed that for the as-cast composites, the addition of SiC{sub p} up to 10% by weight improves the strength but reduces ductility. Further addition of SiC{sub p} reduces the strength and ductility of the composites. At 150 and 300 deg. C the matrix alloy exhibits higher strength than the composites. Extrusion generally raised the strength of the composites at both room and elevated temperatures. Time rupture creep tests carried out at 300 deg. C showed that the composites exhibit higher creep resistance as compared to the matrix alloy except at relatively low stresses where the matrix has a better creep resistance. Extrusion improved the resistance of composites to creep rupture.

36 MATERIALS SCIENCE↗

Towards a Superplastic Forming of Fe-Mn-Al Alloys

The aim is to study the characteristics of superplasticity, mostly on non qualified materials, such as austenitic steel of the Fe-Mn-Al alloy, which has some of the specific material parameters closely related to microstructural mechanisms. These parameters are used as indicators of material superplastic potentiality. The material was submitted to hot tensile testing, within a temperature range from 600 deg. C to 1000 deg. C and strain-rates varying from 10{sup -6} to 1 s{sup -1}. The strain rate sensitivity parameter (m) and observed maximum elongation until rupture ({epsilon}{sub r}) could be determined and also obtained from the hot tensile test. The experiments stated a possibility of superplastic behaviour in a Fe-Mn-Al alloy within a temperature range from 700 deg. C to 900 deg. C with grain size around 3 {mu}m (ASTM grain size 12) and average strain rate sensitivity of m {approx} 0.54, as well as a maximum elongation at rupture around 600%. The results are based on a more enhanced research from the authors; however, this paper has focused just on the hot tensile test, as further creep tests results are not available herein. There are rare examples of superplasticity study of an austenitic steel Fe-Mn-Al alloy, thus this work showed some possibility of exploring the potential use of such materials in this regime at temperatures {>=}700 deg. C.

36 MATERIALS SCIENCE↗