Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “QUALITY FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Direct Detection of Akhiezer Damping in a Silicon MEMS Resonator

Abstract Silicon Microelectromechanical Systems (MEMS) resonators have broad commercial applications for timing and inertial sensing. However, the performance of MEMS resonators is constrained by dissipation mechanisms, some of which are easily detected and well-understood, but some of which have never been directly observed. In this work, we present measurements of the quality factor, Q , for a family of single crystal silicon Lamé-mode resonators as a function of temperature, from 80–300 K . By comparing these Q measurements on resonators with variations in design, dimensions, and anchors, we have been able to show that gas damping, thermoelastic dissipation, and anchor damping are not significant dissipation mechanisms for these resonators. The measured f · Q product for these devices approaches 2 × 10 13 , which is consistent with the expected range for Akhiezer damping, and the dependence of Q on temperature and geometry is consistent with expectations for Akhiezer damping. These results thus provide the first clear, direct detection of Akhiezer dissipation in a MEMS resonator, which is widely considered to be the ultimate limit to Q in silicon MEMS devices.

36 MATERIALS SCIENCE↗

Mitigating coherent loss in superconducting circuits using molecular self-assembled monolayers

In planar superconducting circuits, decoherence due to materials imperfections, especially two-level-system (TLS) defects at different interfaces, is a primary hurdle for advancing quantum computing and sensing applications. Traditional methods for mitigating TLS loss, such as etching oxide layers at metal and substrate interfaces, have proven to be inadequate due to the persistent challenge of oxide regrowth. In this work, we introduce a novel approach that employs molecular self-assembled monolayers (SAMs) to chemically bind at different interfaces of superconducting circuits. This technique is specifically tested here on coplanar waveguide (CPW) resonators, in which this method not only impedes oxide regrowth after surface etching but can also tailors the dielectric properties at different resonators interfaces. The deployment of SAMs results in a consistent improvement in the measured quality factors across multiple resonators, surpassing those with only oxide-etched resonators. The efficiency of our approach is supported by microwave measurements of multiple devices conducted at millikelvin temperatures and correlated with detailed X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) characterizations of SAM-passivated resonators. The compatibility of SAMs materials with the established fabrication techniques offers a promising route to improve the performance of superconducting quantum devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low-loss interconnects for modular superconducting quantum processors

Low-loss superconducting aluminium cables and on-chip impedance transformers can be used to link qubit modules and create superconducting quantum computing networks with high-fidelity intermodule state transfer. Scaling is now a key challenge in superconducting quantum computing. One solution is to build modular systems in which smaller-scale quantum modules are individually constructed and calibrated and then assembled into a larger architecture. This, however, requires the development of suitable interconnects. Here we report low-loss interconnects based on pure aluminium coaxial cables and on-chip impedance transformers featuring quality factors of up to 8.1 x 10 5 , which is comparable with the performance of our transmon qubits fabricated on a single-crystal sapphire substrate. We use these interconnects to link five quantum modules with intermodule quantum state transfer and Bell state fidelities of up to 99%. To benchmark the overall performance of the processor, we create maximally entangled, multiqubit Greenberger-Horne-Zeilinger states. The generated intermodule four-qubit Greenberger-Horne-Zeilinger state exhibits 92.0% fidelity. We also entangle up to 12 qubits in a Greenberger-Horne-Zeilinger state with 55.8 ± 1.8% fidelity, which is above the genuine multipartite entanglement threshold of 1/2.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low-loss superconducting resonators fabricated from tantalum films grown at room temperature

The use of α-tantalum in superconducting circuits has enabled a considerable improvement in the coherence time of transmon qubits. The standard approach to grow α-tantalum thin films on silicon involves heating the substrate, which takes several hours per deposition and prevents the integration of this material with wafers containing temperature-sensitive components. We report a detailed experimental study of an alternative growth method of α-tantalum on silicon, which is achieved at room temperature through the use of a niobium seed layer. Despite a substantially higher density of oxygen-rich grain boundaries in the films sputtered at room temperature, resonators made from these films are found to have state-of-the-art quality factors, comparable to resonators fabricated from tantalum grown at high temperature. This finding challenges previous assumptions about correlations between material properties and microwave loss of superconducting thin films, and opens a new avenue for the integration of tantalum into fabrication flows with limited thermal budget.

36 MATERIALS SCIENCE↗

Structural color printing based on plasmonic metasurfaces of perfect light absorption

Subwavelength structural color filtering and printing technologies employing plasmonic nanostructures have recently been recognized as an important and beneficial complement to the traditional colorant-based pigmentation. However, the color saturation, brightness and incident angle tolerance of structural color printing need to be improved to meet the application requirement. Here we demonstrate a structural color printing method based on plasmonic metasurfaces of perfect light absorption to improve color performances such as saturation and brightness. Thin-layer perfect absorbers with periodic hole arrays are designed at visible frequencies and the absorption peaks are tuned by simply adjusting the hole size and periodicity. Near perfect light absorption with high quality factors are obtained to realize high-resolution, angle-insensitive plasmonic color printing with high color saturation and brightness. Moreover, the fabricated metasurfaces can be protected with a protective coating for ambient use without degrading performances. The demonstrated structural color printing platform offers great potential for applications ranging from security marking to information storage.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Longitudinal eigenvibration of multilayer colloidal crystals and the effect of nanoscale contact bridges

Longitudinal contact-based vibrations of colloidal crystals with a controlled layer thickness are studied. These crystals consist of 390 nm diameter polystyrene spheres arranged into close packed, ordered lattices with a thickness of one to twelve layers. Using laser ultrasonics, eigenmodes of the crystals that have out-of-plane motion are excited. The particle–substrate and effective interlayer contact stiffnesses in the colloidal crystals are extracted using a discrete, coupled oscillator model. Extracted stiffnesses are correlated with scanning electron microscope images of the contacts and atomic force microscope characterization of the substrate surface topography after removal of the spheres. Solid bridges of nanometric thickness are found to drastically alter the stiffness of the contacts, and their presence is found to be dependent on the self-assembly process. Measurements of the eigenmode quality factors suggest that energy leakage into the substrate plays a role for low frequency modes but is overcome by disorder- or material-induced losses at higher frequencies. These findings help further the understanding of the contact mechanics, and the effects of disorder in three-dimensional micro- and nano-particulate systems, and open new avenues to engineer new types of micro- and nanostructured materials with wave tailoring functionalities via control of the adhesive contact properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Systematic over-estimation of lattice thermal conductivity in materials with electrically-resistive grain boundaries

Reducing the thermal conductivity κ of a material via nano-structuring to create small grain sizes is one of the most common strategies to improve thermoelectric materials. In such polycrystalline materials heat carrying phonons are scattered at the grain boundaries, which directly improves the thermoelectric quality factor and ultimately the figure-of-merit zT. In some cases, however, such as in Mg 3 Sb 2 , SnSe, and Mg 2 Si an opposite trend is found where higher lattice thermal conductivity reported in small grain polycrystalline material than in large grain or single crystal materials. This unphysical result indicates a problem with the conventional use of the Wiedemann–Franz law. Here, we trace this problematic finding to the electrical resistance at the grain boundaries, which leads to an overestimation of the phonon or lattice contribution of the thermal conductivity κ L . In materials with significant grain boundary electrical resistance, the estimated electronic contribution to the thermal conductivity LσT is low because the measured electrical conductivity σ is low. However within the grain electrons may still be transporting more heat than the total conductivity suggests, leading to an overestimation of κ L if the conventional κ L = κ – LσT is used with the measured values of κ and σ. Here, the overestimation of κL in small-grain samples is shown to be pervasive across a broad range of thermoelectric materials, including Mg 3 Sb 2 , Mg 2 Si, PbTe, PbSe, SnSe, (Hf,Zr)CoSb, CoSb 3 , and Bi 2 Te 3 alloys, and a correction is necessary to properly understand and predict their charge and heat transport.

36 MATERIALS SCIENCE↗

When do molecular polaritons behave like optical filters?

This review outlines several linear optical effects featured by molecular polaritons arising in the collective strong light–matter coupling regime. Under weak laser irradiation and when the single-molecule light–matter coupling can be neglected (often in the limit when the number of molecules per photon mode is large), we show that the excited-state molecular dynamics under collective strong coupling can be exactly replicated without the cavity using a shaped (or “filtered”) laser, whose field amplitude is enhanced by the cavity quality factor, shining on the bare molecules. As a consequence, the absorption within a cavity can be understood as the overlap between the polariton transmission and the bare molecular absorption, suggesting that polaritons act in part as optical filters. This framework demystifies and provides a straightforward explanation for a large class of experiments and theoretical models in molecular polaritonics, highlighting that the same effects can be achieved without the cavity with shaped laser pulses. With a few modifications, this simple conceptual picture can also be adapted to understand the incoherent nonlinear response of polaritonic systems. This review establishes a clear distinction between polaritonic phenomena that can be fully explained through classical linear optics and those that require a quantum electrodynamics approach. It also highlights the need to differentiate between effects that necessitate polaritons (i.e., hybrid light–matter states) and those that can occur in the weak coupling regime. Here, we further discuss that certain quantum optical effects like fluorescence can be partially described as optical filtering, whereas some others like cavity-induced Raman scattering go beyond this. Further exploration in these areas is needed to uncover novel polaritonic phenomena beyond optical filtering.

Schwennicke, Kai [University of California, San Di↗

Two-dimensional talc as a natural abundant ultra-broadband hyperbolic material

Here, we demonstrate that two-dimensional talc, a naturally abundant phyllosilicate mineral, supports hyperbolic phonon-polaritons (HPhPs) across the mid- and far-infrared wavelengths. Using scattering scanning near-field optical microscopy (s-SNOM) and synchrotron infrared nano-spectroscopy (SINS), we reveal tunable HPhP modes in talc flakes with long lifetimes, high confinement, and quality factors of up to 5. We further observe Fabry–Pérot cavity modes in tapered flakes, confirmed by simulations and analytical modeling. Compared to synthetic crystals, talc offers an ultra-broadband, low-cost, and sustainable platform for infrared nanophotonics and optoelectronics.

36 MATERIALS SCIENCE↗

Geometric Scaling in Deep Inelastic Scattering

The analysis of the scaling properties in deep-inelastic processes using the 'Quality Factor' (QF) method is summarised. Data from HERA and fixed target experiments with x<0.01 are considered. GRV, MRST and CTEQ parametrisations of F{sub 2} and F{sub 2}{sup c} are analysed in the same way to see whether these reproduce the geometric scaling properties seen in data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A Numerical Simulation Of The Pulse Sequence Reconstruction in AC Biased TESs With a {beta} Source

We study the response of micro-calorimeters based on Ir/Au TESs biased by an AC voltage in the MHz range to the power input generated by beta emission in a Re source thermally connected to the calorimeter itself. The micro-calorimeter is assumed to work at -80 mK, and the energy pulses corresponding to the beta emission have an energy distributed between zero and 2.58 KeV. In this numerical simulation the TES is inserted in a RLC resonating circuit, with a low quality factor. The thermal conductivities between the source and the calorimeter and that from the calorimeter to the heat sink are non-linear. The superconducting to normal transition of the TES is described by a realistic non-linear model. The AC current at the carrier frequency, modulated by the changing resistance of the TES, is demodulated and the output is filtered. The resulting signal is analyzed to deduce the attainable time resolution and the linearity of the response.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Cold work study on a 316LN modified alloy for the ITER TF coil conduit

The primary structural component of the cable-in-conduit conductor (CICC) magnets, such as the ITER TF coils is the conduit. This function creates requirements for 4 K strength, toughness, fatigue crack resistance, and ductility after exposure to the superconductor's reaction heat treatment. The tensile ductility of a steel is a quality factor related to fatigue and fracture resistance that can be evaluated more economically with tensile tests rather than fatigue and fracture tests. We subject 316LN modified base metal and welds to a range of cold work from 0% to 20% and a subsequent Nb 3 Sn reaction heat treatment to evaluate the effects on the tensile properties. With the addition of cold work, the 4 K yield strength increases while tensile elongation decreases in both the base metal and weld. Our results are compared to previously published data on the same alloy to evaluate the use of tensile ductility parameters as a materials qualification specification in magnet design.

36 MATERIALS SCIENCE↗

In situ broadband cryogenic calibration for two-port superconducting microwave resonators

We introduce an improved microwave calibration method for use in a cryogenic environment, based on a traditional three-standard calibration, the Thru-Reflect-Line (TRL) calibration. The modified calibration method takes advantage of additional information from multiple measurements of an ensemble of realizations of a superconducting resonator, as a new pseudo-Open standard, to correct errors in the TRL calibration. We also demonstrate an experimental realization of this in situ broadband cryogenic calibration system utilizing cryogenic switches. All calibration measurements are done in the same thermal cycle as the measurement of the resonator (requiring only an additional 20 min), thus avoiding 4 additional thermal cycles for traditional TRL calibration (which would require an additional 12 days). The experimental measurements on a wave-chaotic microwave billiard verify that the new method significantly improves the measured scattering matrix of a high-quality-factor superconducting resonator.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Design and construction of the main linac module for the superconducting energy recovery linac project at Cornell

Cornell University has been designing and building superconducting accelerators for various applications for more than 50 years. Currently, an energy-recovery linac (ERL) based synchrotron-light facility is proposed making use of the existing CESR facility. As part of the phase 1 R and D program funded by the NSF, critical challenges in the design were addressed, one of them being a full linac cryo-module. It houses 6 superconducting cavities- operated at 1.8 K in continuous wave (CW) mode - with individual HOM absorbers and one magnet/ BPM section. Pushing the limits, a high quality factor of the cavities (2⋅10{sup 10}) and high beam currents (100 mA accelerated plus 100 mA decelerated) are targeted. We will present the design of the main linac cryo-module (MLC) being finalized recently, its cryogenic features and report on the status of the fabrication which started in late 2012.

43 PARTICLE ACCELERATORS↗

Stamping single wall nanotubes for circuit quantum electrodynamics

We report on a dry transfer technique for single wall carbon nanotube devices, which allows to embed them in high finesse microwave cavity. We demonstrate the ground state charge readout and a quality factor of about 3000 down to the single photon regime. This technique allows to make devices such as double quantum dots, which could be instrumental for achieving the strong spin photon coupling. It can easily be extended to generic carbon nanotube based microwave devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Measurement of local internal friction in metallic glasses

Atomic force acoustic microscopy (AFAM), an advanced scanning probe microscopy technique, has been used to measure local elastic properties with a spatial resolution given by the tip-sample contact radius. AFAM is based on inducing out-of-plane vibrations in the specimen. The vibrations are sensed by the AFM cantilever from by the photodiode signal when its tip is in contact with the material under test. To measure local damping, the inverse quality factor Q{sup −1} of the resonance curve is usually evaluated. Here, from the contact-resonance spectra obtained, we determine the real and imaginary part of the contact stiffness k* and from these two quantities the local damping factor Q{sub loc}{sup −1} is obtained which is proportional to the imaginary part γ of the contact stiffness. The evaluation of the data is based on the cantilever's mass distribution with damped flexural modes and not on an effective point-mass approximation for the cantilever’s motion. The given equation is simple to use and has been employed to study the local Q{sub loc}{sup −1} of amorphous PdCuSi metallic glass and its crystalline counterpart as a function of position of the AFM tip on the surface. The width of the distribution changes dramatically from the amorphous to the crystalline state as expected from the consequences of the potential-energy landscape picture. The center value of the distribution curve for Q{sub loc}{sup −1} coincides very well with published data, based on global ultrasonic or internal friction measurements. This is compared to Q{sub loc}{sup −1} measured in crystalline SrTiO{sub 3}, which exhibits a narrow distribution, as expected.

36 MATERIALS SCIENCE↗

Design and development of liquid filled polymeric fibers with flexure rate viscoelastic properties

The design and development of a novel category of bi-component polymeric fibers, made of a polymeric sheath and a liquid core is described. To understand and to analyze the flow of molten polymer and liquid within a spin pack, we built a macroscale analogon where co-flow of polymer and liquid is investigated systematically. The macroscale analogon is composed of a glass cylinder with a finite length and a coaxial capillary. The inner fluid flows in the capillary and at its outlet meets the outer fluid flowing inside the glass cylinder. The fluids are pumped into the setup using pressurized bottles with controlled flow rates. A high-speed camera is placed in front of the glass cylinder to record the transient and the steady flow of the two phases and the morphology of their interface during co-flow. We systematically analyzed the combination of various fluids and different injection channel geometries, and used these findings to design a customized spin pack. Extrusion trials with molten polymers and specific liquids resulted in the production of liquid filled polymeric fibers (LFF) with different amounts of liquid from 3% to 33%vol. and diameters from 150μm to 1mm. Fiber morphology has been investigated with the help of optical microscopy and computer tomography, in order to analyze both surface and core morphology. Mechanical characterization of fibers has been carried out with special care to the damping capacity of such fibers using two different methods: two point bending tests to evaluate the energy dissipation of fibers upon bending at low frequency values (0.005-0.5Hz), and analysis of vibration reduction to determine the quality factor at the resonance frequency of the 1{sup st} and 3{sup rd} vibration mode.

36 MATERIALS SCIENCE↗