Pressure transducers dynamically tested with sinusoidal pressure generator
Sinusoidal pressure generator assembly dynamically tests and calibrates pressure transducers by using a chamber whose lowest resonant mode is above the audiofrequency range.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Sinusoidal pressure generator assembly dynamically tests and calibrates pressure transducers by using a chamber whose lowest resonant mode is above the audiofrequency range.
Large pressure gradient effects on AgI using diamond anvil high pressure cell, noting ionic dissociation and diffusion
Pressure probe response determined by sinusoidal pressure generator
Sinusoidal pressure generator for calibration of pressure transducers
Internal pressures of spacecraft compartments in time-varying pressure environment and including outgassing materials
Flammability limits of mixtures of B2H6 and OF2 at saturated vapor pressure at high pressures in presence of inert gases
Sinusoidal pressure generator for determining frequency response of pressure probes
Outgassing pressure variation with time near perigee in satellite-borne pressure gages, using Langmuir model of surface adsorption
Ear oximeter for monitoring blood oxygenation and pressure, pulse rate, and pressure pulse curve, using dc and ac amplifiers
Design considerations for development of operational super-pressure balloon system to carry 50 pounds to 10 millibar atmospheric pressure
Turbulent incompressible air flow in-stream static pressure fluctuations measurement, describing bleed type pressure transducer theory, design and operational characteristics
Total and vapor pressure sensing and hybrid analog/digital electronic controller for multiburn cryogenic spacecraft propulsion pressurization
An analysis of the incompressible turbulent boundary layer, developing under the combined effects of mass transfer and pressure gradient, is presented in this paper. A strip-integral method is employed whereby two of the three governing equations are obtained by integrating the combined momentum and continuity equation to 50 percent and 100 percent, respectively, of the boundary-layer height. The latter equation is the usual momentum-integral equation; the former equation requires specification of shear. Accordingly, Clauser's equilibrium eddy-viscosity law is assumed valid at this point. The third and final equation is obtained by specifying that Stevenson's velocity profiles apply throughout the domain of interest, from which a skin-friction law can be derived. Comparisons of the numerical results with the experiments of McQuaid, which include combined effects of variable pressure gradient and mass transfer, show good agreement.
An investigation was conducted in the NASA/LaRC Low-Turbulence Pressure Tunnel on a 0.03614-scale orbiter model of a 089B configuration with a 139B configuration nose forward of F.S. 500. The tailcone was the TC sub 4 design and was instrumented with eighty-nine pressure orifices. Control surfaces were deflected and three wind tunnel mounting techniques were investigated over an angle-of-attack range from -2 deg to a maximum of 18 deg. In order to determine the sensitivity of the tailcone to changes in Reynolds number, most of the test was made at a Mach number of 0.20 over a Reynolds number range of 2.0 to 10 million per foot. A few runs were made at a Mach number of 0.30 at Reynolds numbers of 4.0, 6.0, and 8 million per foot.
An experiment designed to measure the transformation pressure of zinc sulfide by a primary pressure method using an indentor-anvil system made of single-crystal diamond is discussed. A nonsorting electrode-grid which can be applied directly to the anvil using optical lithography is described, together with the procedures used for positioning.
An instrument to measure atmospheric pressure at the Earth's surface from an orbiting satellite is considered. Surface pressure can be deduced from measurements of the transmission of an atmospheric column at several frequencies at the edges of the 60 GHz oxygen absorption band. An active microwave instrument proposed to make these measurements is the subject of a joint UK-US development program to demonstrate its capabilities. The results of an extensive analysis of the potential performance of the instrument are summarized.
An asymptotic description is derived for the interaction between a shock wave and a turbulent boundary layer in transonic flow, for a particular limiting case. The dimensionless difference between the external flow velocity and critical sound speed is taken to be much smaller than one, but large in comparison with the dimensionless friction velocity. The basic results are derived for a flat plate, and corrections for longitudinal wall curvature and for flow in a circular pipe are also shown. Solutions are given for the wall pressure distribution and the shape of the shock wave. Solutions for the wall shear stress are obtained, and a criterion for incipient separation is derived. Simplified solutions for both the wall pressure and skin friction distributions in the interaction region are given. These results are presented in a form suitable for use in computer programs.
The design of an electrically insulating, high pressure seal using neoprene, nylon, Teflon, and alumina washers is presented. The seals are of use with internally heated pressure vessel systems.