SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A discussion is presented on the bearing strength and bearing load-penetration relations in lunar soil. These were measured in air as a function of bulk density. It was found that the relation between bulk density and the logarithm of the bearing capacity is about linear. Shapes of the load vs penetration curves were observed to be similar to those obtained with particulate material of terrestrial origin.
An evaluation of multispectral photographic techniques for optical penetration of water in the northeastern United States and the Gulf of Mexico coastal waters is presented. The spectral band (493 to 543 nanom), when exposed to place the water mass at about unit density on the photographic emulsion, was found to provide the best water penetration, independent of altitude or time of day, as long as solar glitter from the surface of the water is avoided. An isoluminous color technique was perfected, which eliminates the dimension of brightness from a multispectral color presentation.
Impact tests of a sphere and several cylinders of various masses and fineness ratios, all of aluminum, fired into an aluminum double-sheet structure at velocities near 7 km/sec, show that a cylinder, impacting in the direction of its axis, is considerably more effective as a penetrator than a sphere. Impacts of three cylinders of equal mass, but different fineness ratios, produced holes through the structures' rear sheet, whereas impact of a sphere of the same mass did not. Moreover, it was found that to prevent rear-sheet penetration, the mass of the 1/2-fineness-ratio cylinder had to be reduced by a factor greater than three. Further tests wherein the cylinder diameter was held constant while the cylinder length was systematically reduced showed that a cylinder with a fineness ratio of 0.07 and a mass of only 1/7 that of the sphere was still capable of producing a hole in the rear sheet.
The flow field resulting from the interaction of an upstream facing wall jet with a supersonic counterflowing stream has been investigated. A flow field model and the main parameters governing the phenomena were determined from quantitative and qualitative experimental observations. Experimental results for different ranges of the main parameters are presented. A theoretical analysis was performed to describe the flow field in the mixing region between the two counterflowing streams. The results obtained by applying a locally similar solution compare favorably with the experimentally measured values. Large values of jet penetration were obtained with a high subsonic or low supersonic jet; large interaction forces are characteristics of higher supersonic injections. For the case of large penetration the cooling effectiveness presented as a function of the main parameters indicates the possibility of interacting cooling applications.
Bearing load vs penetration curves have been measured on a 1.3 g sample of lunar soil from the scoop of the Surveyor 3 soil mechanics surface sampler, using a circular indentor 2 mm in diameter. Measurements were made in an Earth laboratory, in air. This sample provided a unique opportunity to evaluate earlier, remotely controlled, in-situ measurements of lunar surface bearing properties. Bearing capacity, measured at a penetration equal to the indentor diameter, varied from 0.02-0.04 N/sq cm at bulk densities of 1.15 g/cu cm to 30-100 N/sq cm at 1.9 g/cu cm. Deformation was by compression directly below the indentor at bulk densities below 1.61 g/cu cm, by outward displacement at bulk densities over 1.62 g/cu cm. Preliminary comparison of in-situ remote measurements with those on returned material indicates good agreement if the lunar regolith at Surveyor 3 has a bulk density of 1.6 g/cu cm at 2.5 cm depth.
Discussion of a possible explanation for the increases in the intensity range of 3- to 12-MeV interplanetary electrons that McDonald et al. (1972) have labeled as 'quiet-time electron increases.' It is argued that the electrons in quiet-time increases are galactic in origin but that the observed increases are not the result of any variation in the modulation of these particles in the inner solar system. It is suggested instead that quiet-time increases may occur when more electrons than normal penetrate a modulating region that lies far beyond the orbit of the earth. The number of electrons penetrating this region may increase when field lines that have experienced an unusually large random walk in the photosphere are carried by the solar wind out to the region. As evidence of this increased random walk, it is shown that five solar rotations before most of the quiet-time increases occur there is an extended period when the amplitude of the diurnal anisotropy (measured by the Deep River neutron monitor) is relatively low. A delay time of five rotations implies that the proposed modulating region lies at about 30 AU from the sun if the average solar-wind speed is assumed to be constant at about 400 km/sec over this distance. The implications for the correlation between periods of low-amplitude diurnal anisotropy and quiet-time increases on interplanetary conditions out to about 30 AU and some possible models for the proposed modulating region are also considered.
Discussion of an analytical model which leads to predictions of reductions in electron concentrations in reentry flow fields due to the injection of electrophilic liquids and water. The processes incorporated into the model are: penetration and breakup of the liquid jet, droplet acceleration and vaporization, expansion of the liquid spray due to droplet vaporization, electrophilic vapor diffusion, heterogeneous and homogeneous charged species recombination kinetics and homogeneous electron attachment kinetics. Spray boundary calculations are shown to be in good agreement with photographic observations of water and Freon E-3 sprays in wind tunnel tests of a scale model RAM C-III flight vehicle. Fixed-bias electrostatic probe data taken during the RAM C-III flight are interpreted in terms of effective jet penetration distances - which are shown to be consistent with calculations using the present model.
Thermal penetrometry is experimental technique for detecting temperature at which frozen prepolymer becomes soft enough to be pierced by weighted penetrometer needle; temperature at which this occurs is called penetration temperature. Apparatus used to obtain penetration temperatures can be set up largely from standard parts.
A program was conducted to determine the fatigue-crack propagation behavior of parent and welded 2219-T87 aluminum alloy sheet under controlled cyclic stress conditions in room temperature air and 300 F air. Specimens possessing an initial surface defect of controlled dimensions were cycled under constant load amplitude until the propagating fatigue crack penetrated the back surface of the specimen. A series of precracked specimens were prepared to determine optimum penetrant, X-ray, ultrasonic, and eddy current nondestructive inspection procedures.
A solution is presented for the jet-flapped wing in two dimensions. The main flow is assumed to be inviscid and incompressible. The flow inside the jet is considered irrotational and the upper and lower boundaries between the jet and free stream are assumed to behave as vortex sheets which allow no mixing. The solution is found to be in satisfactory agreement with two dimensional experimental results and other theoretical work for intermediate values of momentum coefficient, but the regions of agreement vary with jet exit angle. At small values of momentum coefficient, the trajectory for the jet, as computed by this method, has more penetration than that of other available data, while at high values of moment coefficient this solution results in less penetration of the jet into the main flow.
The permeation of benzene and acetone vapors through sulfur-cured natural rubber was studied by the time-lag method. The zero concentration diffusion coefficient, was obtained by the early-time method. The Frisch time lag equation was utilized to estimate both the solubility coefficient and the additional parameter required to define the concentration-dependence of the diffusion coefficient. This form of concentration dependence was manifested by the corresponding permeability coefficient values. At low entering penetrant pressure where the transport coefficients are constant, indirect evidence was obtained that zero diffusion coefficient is the mechanically correct diffusion coefficient. The solubility coefficient values calculated for benzene vapor in natural rubber are in reasonable agreement with published equilibrium sorption data for a similar rubber compound. At higher entering penetrant pressures, average diffusion coefficients obtained at steady state tended to be larger than the corresponding average diffusion coefficients derived from the time-lags.
Details are presented of an investigation aimed at an explanation of the phenomenon of light flashes observed by Apollo crew members. The various theories considered include: penetration of the eye by cosmic particles resulting in retinal stimulation; production of phosphenes or sensations of light through ionization or excitation; appearance of heavily ionized single tracks misinterpreted as light flashes; Cerenkov radiation; and direct excitation of neural tissue by penetrating cosmic rays. It is concluded that the latter two theories are the likeliest mechanisms for the development of a definitive explanation.
Two major problems in welded aluminum spacecraft structure, reliable nondestructive inspection for incomplete weldment penetration and the rapid oxidation of aluminum surfaces left exposed to the atmosphere are investigated. The approach employed to solve both problems was to employ copper as a coating to prevent oxidation of the aluminum and as an opaque additive in the weldment to enhance X-ray detection in the event of incomplete penetration. Both plasma spray and vacuum vapor deposition techniques were evaluated for depositing the copper. A series of welded panels was made using three thicknesses of vacuum-vapor-deposited copper. All weldments were nondestructively inspected by X-ray, then excised into tensile and bend specimens. Mechanical tests were conducted and all data evaluated. It was determined that the vacuum-vapor-deposited coating was superior to a plasma sprayed coating of the same thickness. The vacuum-vapor-deposited coating was more uniform in thickness, provided complete coverage of the aluminum, and was free of cracks and porosity.
Plasma-sprayed copper coatings were developed to protect the aluminum surfaces of spacecraft structures from oxidation, as well as to provide a means of reliable nondestructive X-ray inspection of possible incomplete weldment penetration. Sixty day storage tests of coated aluminum samples indicated the promise of long-term oxidation protection, but revealed no advantage in detecting penetration defects. Delta-scan techniques were used, and peen plating as a means of applying copper to the aluminum surface was investigated.
The effectiveness was assessed of various NDT methods to detect small tight cracks by randomly introducing fatigue cracks into aluminum sheets. The study included optimizing NDT methods calibrating NDT equipment with fatigue cracked standards, and evaluating a number of cracked specimens by the optimized NDT methods. The evaluations were conducted by highly trained personnel, provided with detailed procedures, in order to minimize the effects of human variability. These personnel performed the NDT on the test specimens without knowledge of the flaw locations and reported on the flaws detected. The performance of these tests was measured by comparing the flaws detected against the flaws present. The principal NDT methods utilized were radiographic, ultrasonic, penetrant, and eddy current. Holographic interferometry, acoustic emission monitoring, and replication methods were also applied on a reduced number of specimens. Generally, the best performance was shown by eddy current, ultrasonic, penetrant and holographic tests. Etching provided no measurable improvement, while proof loading improved flaw detectability. Data are shown that quantify the performances of the NDT methods applied.
Test data is presented which allows determination of jet penetration and mixing of multiple cold air jets into a ducted subsonic heated mainstream flow. Jet-to-mainstream momentum flux ratios ranged from 6 to 60. Temperature profile data is presented at various duct locations up to 24 orifice diameters downstream of the plane of jet injection. Except for two configurations, all geometries investigated had a single row of constant diameter orifices located transverse to the main flow direction. Orifice size and spacing between orifices were varied. Both of these were found to have a significant effect on jet penetration and mixing. The best mixing of the hot and cold streams was achieved with duct height.
Large area pressurized meteoroid penetration detector panels with maximum inherent structural rigidity are provided. The panels measure directly the penetration rate in materials to be used in spacecraft. Panel structure include an interconnected cellular configuration in which the cells have spaced periphery welds and tufts in their centers. A spot weld is made at the center point joining the panels.
Modifications to the Pioneer 10/11 meteoroid detection experiment to allow it to be used for outer planet missions were investigated. Both pressurized cells and metal-oxide silicon (MOS) penetration detectors are considered. Both the sensors systems and the electronics are treated. Investigation of the calibration and characterization of the MOS penetration detector is reported.