Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PARALLEL PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Scanning Microscopes Using X Rays and Microchannels

Scanning microscopes that would be based on microchannel filters and advanced electronic image sensors and that utilize x-ray illumination have been proposed. Because the finest resolution attainable in a microscope is determined by the wavelength of the illumination, the xray illumination in the proposed microscopes would make it possible, in principle, to achieve resolutions of the order of nanometers about a thousand times as fine as the resolution of a visible-light microscope. Heretofore, it has been necessary to use scanning electron microscopes to obtain such fine resolution. In comparison with scanning electron microscopes, the proposed microscopes would likely be smaller, less massive, and less expensive. Moreover, unlike in scanning electron microscopes, it would not be necessary to place specimens under vacuum. The proposed microscopes are closely related to the ones described in several prior NASA Tech Briefs articles; namely, Miniature Microscope Without Lenses (NPO-20218), NASA Tech Briefs, Vol. 22, No. 8 (August 1998), page 43; and Reflective Variants of Miniature Microscope Without Lenses (NPO-20610), NASA Tech Briefs, Vol. 26, No. 9 (September 2002) page 6a. In all of these microscopes, the basic principle of design and operation is the same: The focusing optics of a conventional visible-light microscope are replaced by a combination of a microchannel filter and a charge-coupled-device (CCD) image detector. A microchannel plate containing parallel, microscopic-cross-section holes much longer than they are wide is placed between a specimen and an image sensor, which is typically the CCD. The microchannel plate must be made of a material that absorbs the illuminating radiation reflected or scattered from the specimen. The microchannels must be positioned and dimensioned so that each one is registered with a pixel on the image sensor. Because most of the radiation incident on the microchannel walls becomes absorbed, the radiation that reaches the image sensor consists predominantly of radiation that was launched along the longitudinal direction of the microchannels. Therefore, most of the radiation arriving at each pixel on the sensor must have traveled along a straight line from a corresponding location on the specimen. Thus, there is a one-to-one mapping from a point on a specimen to a pixel in the image sensor, so that the output of the image sensor contains image information equivalent to that from a microscope.

Wang, Yu↗

The shuttle glow: A program to study the ram-induced phenomena

In January 1984, a proposal was submitted to NASA Headquarters entitled The Shuttle Glow: A Program to Determine the Physics of the Ram induced Phenomena. This proposal included the following elements in a shuttlebased experiment: (1) The use of a special flat generating surface 1 x 3 m on which the glow can be produced and observed. This surface will be maneuvered to vary the orientation of ram flow and of projected component of geomagnetic field. (2) Remotely mounted optical instruments to view the glowing layer on the plate. By scanning, the variation of radiance as a function of wavelength and standoff distance from the plate will be observed looking parallel to the plate. (3) The preferred location of the generating plate and in situ diagnostics is on the end of the Remote Manipulator System (RMS) arm.

Anderson, H. R.↗

CFD Analysis and Design of Detailed Target Configurations for an Accelerator-Driven Subcritical System

High-fidelity analysis has been utilized in the design of beam target options for an accelerator driven subcritical system. Designs featuring stacks of plates with square cross section have been investigated for both tungsten and uranium target materials. The presented work includes the first thermal-hydraulic simulations of the full, detailed target geometry. The innovative target cooling manifold design features many regions with complex flow features, including 90 bends and merging jets, which necessitate three-dimensional fluid simulations. These were performed using the commercial computational fluid dynamics code STAR-CCM+. Conjugate heat transfer was modeled between the plates, cladding, manifold structure, and fluid. Steady-state simulations were performed but lacked good residual convergence. Unsteady simulations were then performed, which converged well and demonstrated that flow instability existed in the lower portion of the manifold. It was established that the flow instability had little effect on the peak plate temperatures, which were well below the melting point. The estimated plate surface temperatures and target region pressure were shown to provide sufficient margin to subcooled boiling for standard operating conditions. This demonstrated the safety of both potential target configurations during normal operation.

43 PARTICLE ACCELERATORS↗

A mixture theory formulation for hydraulic or pneumatic transport of solid particles

In this paper, we discuss the importance of constitutive modeling of the stress tensors in certain engineering issues, related to the pressure drop and skin friction, encountered in solids transport. To study this problem, we first give a brief account of the formulation of a two-component mixture based on the theory proposed by Massoudi, Rajagopal and co-workers. The mixture consists of a linearly viscous fluid infused with solid particles. The solids particles are modeled as a granular media and it is assumed that the mixture is dense enough so that we can use the theory of interacting continua. The subsequent boundary value problem, flow between two flat plates, is then solved numerically and results for various dimensionless numbers are presented for velocities and volume fraction profiles. The engineering quantities of interests discussed are related to the pressure drop and skin friction at the walls.

97 MATHEMATICS AND COMPUTING↗

Energy transfer between a passing vortex ring and a flexible plate in an ideal quiescent fluid

Recent advancements in highly deformable smart materials have lead to increasing interest in small-scale energy harvesting research for powering low consumption electronic devices. One such recent experimental study by Goushcha et al. explored energy harvesting from a passing vortex ring by a cantilevered smart material plate oriented parallel to and offset from the path of the ring in an otherwise quiescent fluid. The present study focuses on modeling this experimental study using potential flow to facilitate optimization of the energy extraction from the passing ring to raise the energy harvesting potential of the device. The problem is modeled in two-dimensions with the vortex ring represented as a pair of counter-rotating free vortices. Vortex pair parameters are determined to match the convection speed of the ring in the experiments, as well as the imposed pressure loading on the plate. The plate is approximated as a Kirchhoff-Love plate and represented as a finite length vortex sheet in the fluid domain. The analytical model matches experimental measurements, including the tip displacement, the integrated force along the entire plate length as a function of vortex ring position, and the pressure along the plate. The potential flow solution is employed in a parametric study of the governing dimensionless parameters in an effort to guide the selection of plate properties for optimal energy harvesting performance. Results of the study indicate an optimal set of plate properties for a given vortex ring configuration, in which the time-scale of vortex advection matches that of the plate vibration.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Quantum two-photon emission in a photonic cavity

In this paper, we derive an expression for the two-photon spontaneous emission (TPSE) rate of an excited quantum emitter in the presence of arbitrary bodies in its vicinities. After investigating the influence of a perfectly conducting plate on the TPSE spectral distribution (Purcell effect), we demonstrate the equivalence of our expression with the more usual formula written in terms of the corresponding dyadic Green's function. We establish a convenient relation between the TPSE spectral distribution and the corresponding Purcell factors of the system. Next, we consider an emitter close to a dielectric medium and show that, in the near-field regime, the TPSE spectral distribution is substantially enhanced and changes abruptly at the resonance frequencies. Finally, motivated by the suppression that may occur in the one-photon spontaneous emission of an excited atom between two parallel conducting plates, we discuss the TPSE for this same situation and show that complete suppression can never occur for s → s transitions.

74 ATOMIC AND MOLECULAR PHYSICS↗

Defectoscopy of ZnGeP{sub 2} single crystals using a strontium vapour laser

A modified method of optical defectoscopy of ZnGeP{sub 2} single crystal plates using a strontium vapour laser (λ = 1.03 and 1.09 μm) is proposed based on shadow imaging of internal defects in plates cut parallel to the (100) plane. It is shown that the use of a strontium vapour laser with a wavelength of 6.45 mm makes it possible to study inhomogeneities in large-size ZnGeP{sub 2} samples. The possibility of fabricating a projection defectoscope for monitoring breakdown development in ZnGeP{sub 2} crystals is considered. (laser applications)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental study on corrugated cross-flow air-cooled plate heat exchangers

Experimental study on cross-flow air-cooled plate heat exchangers (PHEs) was performed. The two prototype PHEs were manufactured in a stack of single-wave plates and double-wave plates in parallel. Cooling air flows through the PHEs in a crosswise direction against internal cooling water. The heat exchanger aims to substitute open-loop cooling towers with closed-loop water circulation, which guarantees cleanliness and compactness. In this study, the prototype PHEs were tested in a laboratory scale experiments. From the tests, double-wave PHE shows approximately 50% enhanced heat transfer performance compared to single-wave PHE. However, double-wave PHE costs 30% additional pressure drop. For commercialization, a wide channel design for air flow would be essential for reliable performance. (author)

42 ENGINEERING↗

Early age strength enhancement of blended cement systems by CaCl{sub 2} and diethanol-isopropanolamine

The enhancement of the 1 day strength of cementitious systems by a combination of calcium chloride (CaCl{sub 2}) and diethanol-isopropanolamine (DEIPA) was studied, particularly in blended cement systems. A combination of quantitative X-ray diffraction with Rietveld refinement (QXRD), scanning electron microscopy (SEM)/backscattered electron image analysis, thermogravimetric analysis (TGA), and isothermal calorimetry were used to investigate the mechanism of strength enhancement by the additives. The additives were found to increase the early age mortar strength by enhancing the cement hydration, with the DEIPA enhancing primarily the aluminate hydration. DEIPA also affected the morphology of portlandite which was formed as thin plates. In parallel, the calcium-to-silica ratio of the C-S-H was found to increase with the use of DEIPA, possibly because of the inclusion of microcrystalline portlandite. After 48 h DEIPA was found to directly enhance the rate of reaction of granulated blast-furnace slag and fly ash.

36 MATERIALS SCIENCE↗

Neutron-induced fission measurements at the time-of-flight facility nELBE

Neutron-induced fission of ²⁴²Pu is studied at the photoneutron source nELBE. The relative fast neutron fission cross section was determined using actinide fission chambers in a time-of-flight experiment. A good agreement of present nuclear data with evalua- tions has been achieved in the range of 100 keV to 10 MeV.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Machine learning-based optimization of air-cooled heat sinks

Machine learning-based models using Artificial Neural Network (ANN) and greedy search algorithm are used to optimize air-cooled parallel plate-finned heat sinks (PPFHSs) subjected to laminar flow over an extensive range of design parameters. Here, the thermal and hydraulic performances of PPFHSs are represented by heat transfer coefficient (h) and pressure drop (ΔP), respectively. Optimization objectives for PPFHS designs can vary from industry to industry depending on their design priorities. The present study proposes a novel and generalized optimization method that defines practical optimization objectives and provides an accurate optimization process to design effective PPFHSs for a wide range of industrial applications with different design requirements. Three optimization objectives are presented in this study: (i) the largest h PΔ, (ii) the largest h within a specified maximum allowed flow rate, and (iii) the lowest weight that maximizes h for operation within the maximum allowed flow rate. While the shortcoming of the first objective is demonstrated, the other two objectives are found to be suitable for designing effective heat sinks (HSs) across different applications. Results suggest a promising trend from the third objective to develop HSs with ~ 37-68% lower weight, 80-85% reduced ΔP, and negligible penalty in h compared with optimized HSs obtained from the second objective. However, since the third objective leads to HSs with thinner fins, structural analysis should be performed to ensure reliable operation of the HSs.

42 ENGINEERING↗

Field emission from vertically aligned few-layer graphene

The electric field emission behavior of vertically aligned few-layer graphene was studied in a parallel plate-type setup. Few-layer graphene was synthesized in the absence of any metallic catalyst by microwave plasma enhanced chemical vapor deposition with gas mixtures of methane and hydrogen. The deposit consists of nanostructures that are several micrometers wide, highly crystalline stacks of four to six atomic layers of graphene, aligned vertically to the substrate surface in a high density network. The few-layer graphene is found to be a good field emitter, characterized by turn-on fields as low as 1 V/{mu}m and field amplification factors up to several thousands. We observe a clear dependence of the few-layer graphene field emission behavior on the synthesis parameters: Hydrogen is identified as an efficient etchant to improve field emission, and samples grown on titanium show lower turn-on field values and higher amplification factors when compared to samples grown on silicon.

36 MATERIALS SCIENCE↗

Wave amplification by a relativistic electron beam in a planar electrostatic system with sinusoidal-ripple boundary

Primary study is devoted to the amplification mechanism of electromagnetic fast wave by a relativistic electron beam in a planar electrostatic system, where the superplate of two parallel metallic plates is corrugated with sinusoidal ripples and connected to a negative voltage, while the subplate is smooth and grounded. In the system the electrostatic field governs the electrons to move along approximately sinusoidal trajectories and pumps the kinetic energy of electrons to the wave. Under exclusion of the space-charge wave effect and the Smith-Purcell effect, the fast wave gets relativistic Doppler upshift frequency and gain by extracting energy from a sheet electron beam, which is very similar to that in a free-electron laser pumped by a magnetostatic wiggler. Formulas derived and numerical analysis indicate that the amplification mechanism of wave pumped by the planar electrostatic system with sinusoidal ripples is favorable for a mildly relativistic electron beam to generate terahertz wave.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Investigation of the effects of a thin dielectric layer on low-pressure hydrogen capacitive discharges driven by combined radio frequency and pulse power sources

Negative hydrogen ion sources, for instance for fusion devices, currently attract considerable attention. To generate the precursors—highly rovibrationally excited hydrogen molecules—for negative hydrogen ions effectively by electron excitation, a thin dielectric layer is introduced to cover the surface of the electrically grounded electrode of two parallel metal plates in a low-pressure hydrogen capacitive discharge driven by combined rf and pulse power sources. To understand the characteristics of such discharges, particle-in-cell simulations are conducted to study the effects that the single dielectric layer would bring onto the discharges. The simulation results show that the dielectric layer leads to a much higher plasma density and a much larger production rate of highly vibrationally excited hydrogen molecules compared to discharges without the dielectric layer on the electrode. Further investigation indicates that the nonlinear oscillation of the electrons induced by the nanosecond-pulse continues until it is finally damped down and does not show any dependence on the pulse plateau-time, which is in stark contrast to the case without the dielectric layer present. The physical reason for this phenomenon is explored and explained.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of a magnetically driven reconnection platform using ultrafast proton radiography

A novel magnetically driven reconnection platform was created by a pair of U-shaped Cu coils that connect two parallel Cu plates irradiated at a focused laser intensity of ~3 × 10 16 W/cm 2 and characterized using ultrafast proton radiography. The proton data show two prolate voids, each corresponding to the coil current, with an inferred maximum magnitude of 57 ± 4 kA. A center “flasklike” feature was also observed in the proton radiographs. By prescribing electromagnetic fields associated with magnetic reconnection in proton ray tracing simulations, characteristics of this center feature were reproduced. Finally, these results demonstrate the robustness of the laser-driven capacitor coils for generating strong magnetic fields and provide promise of using such coils as a viable platform for studying magnetically driven reconnection in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lasing in zinc selenide single crystals pumped by high-voltage subnanosecond pulses

The action of subnanosecond high-voltage pulses (U = 50-200 kV, t{sub p} = 100-500 ps) on 1-2-mm-thick plane-parallel ZnSe plates is studied. A sample was placed between a cathode and a circular anode. A discharge propagated along the lines of force of the electric field. Lasing at 480 nm appeared at the discharge front and opposite to the cathode. The average propagation velocity of the discharge achieved 5x10{sup 8} cm s{sup -1}, the pulse power was 600 W, and the radiation divergence did not exceed 2-3 deg. No streamer discharges oriented along crystallographic directions were observed. (lasers)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Beam test performance of prototype silicon detectors for the Outer Tracker for the Phase-2 Upgrade of CMS

A new CMS tracker detector will be installed for operation at the High Luminosity LHC (HL-LHC). This detector comprises modules with two closely spaced parallel sensor plates and front-end ASICs capable of transmitting tracking information to the CMS Level-1 (L1) trigger at the 40 MHz beam crossing rate. The inclusion of tracking information in the L1 trigger decision will be essential for selecting events of interest efficiently at the HL-LHC. The CMS Binary Chip (CBC)has been designed to read out and correlate hits from pairs of tracker sensors, forming so called track stubs. For the first time, a prototype irradiated module and a full-sized module, both equipped with the version 2 of the CBC, have been operated in test beam facilities. The efficiency of the stub finding logic of the modules for various angles of incidence has been studied. The ability of the modules to reject tracks with transverse momentum less than 2 GeV has been demonstrated. For modules built with irradiated sensors, no significant drop in the stub finding performance has been observed. Results from the beam tests are described in this paper.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗