Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OPERATIONAL PROBLEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Development of coatings to control electroosmosis in zero gravity electrophoresis

A major problem confronting the operation of free fluid electrophoresis in zero gravity is the control of electrokinetic phenomena and, in particular, electroosmosis. Due to the severity of counter flow, as a result of electroosmosis, the electrical potential developed at the surface of shear must be maintained at near, or as close to, zero millivolts as possible. Based upon this investigation, it has been found that the amount of bound water or the degree of hydroxylation plays a major role in the control of this phenomena. Of necessity, factors, such as adhesion, biocompatibility, protein adsorption, and insolubility were considered in this investigation because of the long buffer-coating exposure times required by present space operations. Based upon tests employing microcapillary electrophoresis, it has been found that gamma amino propyl trihydroxysilane produced a coating which provides the lowest potential (minus 3.86 mv) at the surface of shear between the stationary and mobile layers. This coating has been soaked in both borate and saline buffers, up to three months, in a pH range of 6.5 to 10 without deleterious effects or a change in its ability to control electrokinetic effects.

Krupnick, A. C.↗

Design and performance analysis of solid-propellant rocket motors using a simplified computer program

An analysis and a computer program are presented which represent a compromise between the more sophisticated programs using precise burning geometric relations and the textbook type of solutions. The program requires approximately 900 computer cards including a set of 20 input data cards required for a typical problem. The computer operating time for a single configuration is approximately 1 minute and 30 seconds on the IBM 360 computer. About l minute and l5 seconds of the time is compilation time so that additional configurations input at the same time require approximately 15 seconds each. The program uses approximately 11,000 words on the IBM 360. The program is written in FORTRAN 4 and is readily adaptable for use on a number of different computers: IBM 7044, IBM 7094, and Univac 1108.

Sforzini, R. H.↗

Development of coatings to control electroosmosis in zero gravity electrophoresis

A major problem confronting the operation of free fluid electrophoresis in zero gravity is the control of electrokinetic phenomena and, in particular, electroosmosis. Due to the severity of counter flow as a result of electroosmosis, the electrical potential developed at the surface of shear must be maintained at near, or as close, to zero millivolts as possible. Based upon this investigation, it has been found that the amount of bound water or the degree of hydroxylation plays a major role in the control of this phenomenon. Based upon tests employing microcapillary electrophoresis, it has been found that gamma amino propyl trihydroxysilane produced a coating which provides the lowest potential (about 3.86 mV) at the surface of shear between the stationary and mobile layers.

Krupnick, A. C.↗

Mariner 10 Venus encounter

Review of the scientific objectives of the Mariner 10 mission with regard to observations of Venus during a flyby, and description of the equipment installed on the spacecraft to fulfill these objectives. A detailed description is given of the hardware modifications made to the payload specifically for the Venus sequence. In discussing the encounter operations, two spacecraft problems which significantly affected the Venus encounter sequence are cited - namely, a failure of the television optic heaters to come on shortly after launch, and the occurrence of a roll gyro oscillation.

Dunne, J. A.↗

The design, development, fabrication and testing of two (2) Non-Spin Platforms, (NSP)

The non spin platform is a means for achieving the very low acceleration requirements for cost effective space processing experiments on research rocket flights. These platforms have a low initial cost, are re-usable and have extremely low refurbishment cost. In order to attain this goal, commercially available components were used and only the necessary quality control standards were imposed. A detailed system description, the very few design problems encountered, the operational procedures (both pre-flight and post-flight), and the maintenance requirements are described.

Source record↗

A simplified application of the method of operators to the calculation disturbed motions of an airplane

A simplified treatment of the application of Heaviside's operational methods to problems of airplane dynamics is given. Certain graphical methods and logarithmic formulas that lessen the amount of computation involved are explained. The problem of representing a gust disturbance or control manipulation is taken up and it is pointed out that in certain cases arbitrary control manipulations may be dealt with as though they imposed specific constraints on the airplane, thus avoiding the necessity of any integration whatever.

Jones, R. T.↗

Science aspects of a 1980 flyby of Comet Encke with a Pioneer spacecraft

Results are presented of an investigation of the feasibility of a 1980 flyby of Comet Encke using a Pioneer class spacecraft. Specific areas studied include: science objectives and rationale; science observables; effects of encounter velocity; science encounter and targeting requirements; selection and description of science instruments; definition of a candidate science payload; engineering characteristics of suggested payload; value of a separable probe; science instruments for a separable probe; science payload integration problems; and science operations profile.

Jaffe, L. D.↗

Digital data processing system dynamic loading analysis

Simulation and analysis of the Space Shuttle Orbiter Digital Data Processing System (DDPS) are reported. The mated flight and postseparation flight phases of the space shuttle's approach and landing test configuration were modeled utilizing the Information Management System Interpretative Model (IMSIM) in a computerized simulation modeling of the ALT hardware, software, and workload. System requirements simulated for the ALT configuration were defined. Sensitivity analyses determined areas of potential data flow problems in DDPS operation. Based on the defined system requirements and the sensitivity analyses, a test design is described for adapting, parameterizing, and executing the IMSIM. Varying load and stress conditions for the model execution are given. The analyses of the computer simulation runs were documented as results, conclusions, and recommendations for DDPS improvements.

Lagas, J. J.↗

Viking X-band telemetry experiment

In order to uncover operational and design problems in the use of X-band by the 1977 Mariner Jupiter-Saturn mission and future spacecraft using the Deep Space Network, the Viking X-band telemetry experiment was conducted. The experiment was conducted during the months of December 1975 and January 1976. During each of the five successful passes, a periodic sequence (in lieu of ranging) was transmitted to the spacecraft and returned by the spacecraft transponder on both S- and X-bands. These telemetry-like signals were received, demodulated, and detected. From a variety of measurements at the station, four independent measurements were made of the received signal-to-noise ratio (SNR). These four SNRs were later compared with each other and the predicted SNR. The principal result of the experiment is that X-band telemetry works as expected. That is, the measured SNRs were consistent relative to each other and to the predicted values within the accuracy of the experiment.

Weber, W. J., III↗

TCV software test and validation tools and technique

The paper describes techniques for testing and validating software for the TCV (Terminal Configured Vehicle) program which is intended to solve problems associated with operating a commercial transport aircraft in the terminal area. The TCV research test bed is a Boeing 737 specially configured with digital computer systems to carry out automatic navigation, guidance, flight controls, and electronic displays research. The techniques developed for time and cost reduction include automatic documentation aids, an automatic software configuration, and an all software generation and validation system.

Straeter, T. A.↗

A large hemispherical chamber for fire toxicity tests

The paper describes an 84-liter chamber for fire toxicity tests consisting of an upper hemispherical dome section with a diameter of 533 mm, made of clear polymethyl methacrylate and a lower cylindrical base section 190 mm deep, made of cast aluminum. The chamber is designed to expose 36 mice, 8 rats, 4 rabbits or combinations of smaller numbers of two or three species simultaneously to the gaseous products of pyrolysis or combustion. The chamber does not appear to be suitable for screening purposes because its large size introduces operating costs and problems which reduce its cost effectiveness.

Hilado, C. J.↗

Space shuttle orbiter digital data processing system timing sensitivity analysis OFT ascent phase

Dynamic loads were investigated to provide simulation and analysis of the space shuttle orbiter digital data processing system (DDPS). Segments of the ascent test (OFT) configuration were modeled utilizing the information management system interpretive model (IMSIM) in a computerized simulation modeling of the OFT hardware and software workload. System requirements for simulation of the OFT configuration were defined, and sensitivity analyses determined areas of potential data flow problems in DDPS operation. Based on the defined system requirements and these sensitivity analyses, a test design was developed for adapting, parameterizing, and executing IMSIM, using varying load and stress conditions for model execution. Analyses of the computer simulation runs are documented, including results, conclusions, and recommendations for DDPS improvements.

Lagas, J. J.↗

Real time reflectometer

A real time reflectometer with the particular utility of measuring fairly rapid (transient) changes in the specular reflectance of a sample which is continuously exposed to a perturbing environment is described. A fixed radiation source, a fixed detector, a uniformly rotating sample wheel, and a uniformly rotating optical wheel protect against misalignment problems. The reflectometer operates by comparing the measurings of a reflected signal with that of a reference signal made within fractions of a second of one another. Reflectance is measured in the infrared, visible, and vacuum ultraviolet regions.

Zwiener, J. M.↗

Application of Laminar Flow Control Technology to Long-Range Transport Design

The impact of laminar flow control (LFC) technology on aircraft structural design concepts and systems was discussed and the corresponding benefits were shown in terms of performance and fuel economy. Specific topics discussed include: (1) recent advances in laminar boundary layer development and stability analysis techniques in terms of suction requirements and wing suction surface design; (2) validation of theory and realistic simulation of disturbances and off-design conditions by wind tunnel testing; (3) compatibility of aerodynamic design of airfoils and wings with LFC requirements; (4) structural alternatives involving advanced alloys or composites in combinations made possible by advanced materials processing and manufacturing techniques; (5) addition of suction compressor and drive units and their location on the aircraft; and (6) problems associated with operation of LFC aircraft, including accumulation of insects at low altitudes and environmental considerations.

Gratzer, L. B.↗

The Missions of the Viking Orbiters

A description of the orbiter science instruments is presented and the chronology of the two Viking missions is reviewed. The design of the Viking orbiter spacecraft is discussed, taking into account the propulsion subsystem, the attitude control subsystem, the planetary scan platform, aspects of command processing, problems of instrument operation and data processing, and data quantity limitations. Details concerning the Viking orbits and the visibility of the planet are also considered and the future of the Viking orbiter missions is evaluated. If the orbiters continue to perform well, all the orbiter science investigations will continue to acquire data for another year and perhaps somewhat longer.

Snyder, C. W.↗

Development of concepts for satellite retrieval devices

The teleoperator being developed to augment the Space Transportation System (STS) for satellite placement, retrieval, or servicing at altitudes or orbital planes where it would be impractical to use the shuttle is primarily a general purpose propulsion stage that can be fitted with manipulator arms, automated servicers and satellite retrieval devices for particular missions. Design concepts for a general purpose retrieval device for docking with a satellite to which a grappling fixture has been attached, and for a retrieval device for docking with the Solar Maximum Mission (SMM) spacecraft were defined. The mechanical aspects of these two devices are discussed as well as the crew operations involved and problems created by the requirement for remote control. Drawings for the two retrieval device concepts are included.

Pruett, E. C.↗

A review of issues and strategies in nondestructive evaluation of fiber reinforced structural composites

Techniques for quantitative assessment of the mechanical strength and integrity of fiber composites during manufacture and service and following repair operations are presented. Problems and approaches are discussed relative to acceptance criteria, calibrating standards, and methods for nondestructive evaluation of composites in strength-critical applications. Acousto-ultrasonic techniques provide the methods of choice in this area.

Vary, A.↗

The OMNIUM-G HTC-25 tracking concentrator

A point focusing, two axis tracking, high concentration ratio parabolic reflector is described. Field experience coupled with engineering improvements are shown to have manifested a design that is economic in the areas of manufacturing, packaging, delivering, installing, and commissioning the system into operation. The initial problems specifically with the OMNIUM-G model HTC-25 tracking concentrator are addressed.

Zelinger, S.↗