Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Improving the Mechanical Properties of Cast Aluminum Via Ultrasonication-Induced Microstructural Refinement

One barrier to the broader use of cast aluminum alloys in automotive applications is their poor mechanical properties, especially compared to wrought materials. This study investigates the use of ultrasound to refine the microstructure of cast aluminum alloys during solidification and thus improve their mechanical properties. An A356 aluminum alloy (Al-Si-Mg) with added Fe (to mimic a recycle-grade alloy) was cast in a graphite mold with the simultaneous application of ultrasound. Tensile specimens were extracted from the castings and heat treated to a T6 temper. Ultrasonication during casting transformed the morphology of primary aluminum grains from dendritic (~140 microns in size) to globular (~36 microns in size), increased the ultimate tensile strength by 10 %, and tripled the ductility compared to casting without ultrasound. This improvement in strength and ductility demonstrates the potential for ultrasonic processing to improve the performance of cast aluminum alloys without altering their chemistry or additional post-processing.

Aluminum, Solidification, Ultrasound, Grain refinm↗
DOE OSTI2024

Influence of high-strain-rate compression and subsequent heat treatment on (TiNbZr) 89 (AlTa) 11 refractory high-entropy alloys: Dynamic-mechanical behavior and microstructural changes

This study explored the dynamic-mechanical behavior of a novel low-density (TiNbZr) 89 (AlTa) 11 refractory high-entropy alloy (RHEA) across strain rates ranging from 1.0×10 3 to 3.5×10 3 s –1 . A significant increase in the yield and ultimate compressive strengths with rising strain rates up to 3.0×10 3 s –1 was observed and attributed to enhanced dislocation activities and stress-induced microstructural transformations. The formation of the B2 phase and Zr 5 Al 3 precipitates was found to be crucial in bolstering the alloy strength at high strain rates. Beyond strain rates of 3.0×10 3 s –1 , a decrease in strength occurred due to thermal softening and strain localization. Microstructural analyses at 3.5×10 3 s –1 revealed grain refinement, the development of micro shear bands, and dislocation tangles, which were indicative of dynamic recrystallization. Besides, the findings also revealed that the post-dynamic compression heat treatment further enhanced the hardness and microstructural stability of the alloy. These results highlight the potential of the (TiNbZr) 89 (AlTa) 11 RHEA for applications requiring materials with high strength-to-weight ratios, particularly in dynamically loaded environments. It is expected that the results of this study will further advance our fundamental understanding of the behavior of RHEAs under extreme conditions, thereby opening new avenues for material innovation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Graph neural networks for efficient learning of mechanical properties of polycrystals

Herein we present graph neural networks (GNNs) as an efficient and accurate machine learning approach to predict mechanical properties of polycrystalline materials. Here, a GNN was developed based on graph representation of polycrystals incorporating only fundamental features of grains including their crystallographic orientation, size, and grain neighbor connectivity information. We tested our method on modeling stiffness and yield strength of α -Ti microstructures, varying in their crystallographic texture. We find the GNN predicts both properties with high accuracy with mean relative errors of ~1% for unseen microstructures from a given set of textures and < 2% for microstructures of unseen texture, even when presented with limited training data. This accuracy is comparable to methods that require high-resolution three-dimensional (3D) microstructure data, such as 3D convolutional neural networks (3D-CNNs) and models that depend on the computation of spatial statistics. The present results show that graph-based deep learning is a promising framework for property prediction, especially considering the high cost associated with obtaining high-resolution 3D microstructure data and the general scarcity of experimental materials datasets.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Predicting Microstructural Void Nucleation in Discontinuous Fiber Composites through Coupled in-situ X-ray Tomography Experiments and Simulations

Composite materials have become widely used in engineering applications, in order to reduce the overall weight of structures while retaining their required strength. In this work, a composite material consisting of discontinuous glass fibers in a polypropylene matrix is studied at the microstructural level through coupled experiments and simulations, in order to uncover the mechanisms that cause damage to initiate in the microstructure under macroscopic tension. Specifically, we show how hydrostatic stresses in the matrix can be used as a metric to explain and predict the exact location of microvoid nucleation that occurs during damage initiation within the composite’s microstructure. Furthermore, this work provides evidence that hydrostatic stresses in the matrix can lead to coupled microvoid nucleation and early fiber breakage, and that small fragments of fibers can play an important role in the process of microvoid nucleation. These results significantly improve our understanding of the mechanics that drive the initiation of damage in the complex microstructures of discontinuous fiber reinforced thermoplastics, while also allowing scientists and engineers to predict the microstructural damage behavior of these composites at sub-fiber resolution and with high accuracy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Material Characterization Report of FFTF MFF 5 Fuel Element

This report was written as part of the TerraPower Cooperative Research and Development Agreement No. 11-CR-19 with Idaho National Laboratory. TerraPower provided the funding. An as-fabricated fuel element from the Fast Flux Test Facility MFF-5 experiment was sectioned and analyzed for material properties. Results reported include phase characterization, microstructural analysis, density, microhardness, and chemical composition.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Strain-Induced Shifts in Defective Graphite Phonon Modes Predicted by Density Functional Theory

Carbon fiber composites have gained attention as a structural material because of their high strength-to-weight ratio, and understanding the effect of defects on reactivity and mechanical properties is important for the longevity and safety of the composite. Although it is known that strain causes the underlying graphitic vibrational modes to redshift, it is not clear how strain may alter reactivity and defect-induced vibrational changes. To investigate the strain-induced phonon changes of defective carbon fiber composites, density functional theory calculations of graphite are used, including intercalated hydrogen and fluorine defects. By comparing changes in the bond lengths, formation energies, and phonon density of states for uniaxially and biaxially strained graphite, strain was found to generally make defect formation more favorable and the specific behavior changes are dependent on the strain direction and defect identity. Specifically, intercalated fluorine phonons are more sensitive to strain than hydrogen intercalation phonons, and strain applied along the zigzag direction alters the calculated properties more than strain along the armchair direction. Finally, these results highlight the importance of understanding the microstructural effect of deviations from the ideal material because small changes in strain or defect type can significantly alter the behavior of the carbon fiber composite core.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High-Throughput Microstructural Characterization and Process Correlation Using Automated Electron Backscatter Diffraction

The need to optimize the processing conditions of additively manufactured (AM) metals and alloys has driven advances in throughput capabilities for material property measurements such as tensile strength or hardness. High-throughput (HT) characterization of AM metal microstructure has fallen significantly behind the pace of property measurements due to intrinsic bottlenecks associated with the artisan and labor-intensive preparation methods required to produce highly polished surfaces. This inequality in data throughput has led to a reliance on heuristics to connect process to structure or structure to properties for AM structural materials. In this study, we show a transformative approach to achieve laser powder bed fusion (LPBF) printing, HT preparation using dry electropolishing and HT electron backscatter diffraction (EBSD). This approach was used to construct a library of > 600 experimental EBSD sample sets spanning a diverse range of LPBF process conditions for AM Kovar. This vast library is far more expansive in parameter space than most state-of-the-art studies, yet it required only approximately 10 labor hours to acquire. Build geometries, surface preparation methods, and microscopy details, as well as the entire library of >600 EBSD data sets over the two sample design versions, have been shared with intent for the materials community to leverage the data and further advance the approach. Using this library, we investigated process–structure relationships and uncovered an unexpected, strong dependence of microstructure on location within the build, when varied, using otherwise identical laser parameters.

Characterization and Analytical Technique↗
DOE OSTI2023

Derivation of heterogeneous material distributions and their sensitivity to HM-coupled two-phase flow models exemplified with the LASGIT experiment

Abstract Advective gas transport in bentonite, a possible buffer material in repositories for radioactive materials, is difficult to simulate in numerical continuum models, partly due to the complicated microstructure of bentonite. To generate reliable models of repositories nevertheless, spatially distributed heterogeneous material properties can be used to allow localization of gas flow. In this study, a pore-size-dependent stochastic approach of the gas entry pressure is derived from Mercury Intrusion Porosimetry, which is used to replicate measurements from the LASGIT experiment. In addition, three benchmark tests are simulated to investigate the dependence of heterogeneous distributions of material properties on the mesh discretization, the temporal dependence, and the coupling between the processes influenced by the heterogeneous parameters. The numerical modeling results of the LASGIT experiment show that the onset of gas flow into the system and the subsequent increase in pressure and stress can be well reproduced using heterogeneous distributions. Compared to a model with homogeneous material properties, heterogeneous distributions may allow the generation of dilatancy-controlled microfractures—an important feature with regard to the advective gas flow in bentonites. However, it can be observed that the heterogeneous distributions in LASGIT are less significant, as technical gaps or differences in material types could have a greater impact.

Environmental Sciences & Ecology↗
DOE OSTI2021

Deuterium permeation and retention in 316L Stainless Steel Manufactured by Laser Powder Bed Fusion

Deployment of additively manufactured materials into nuclear energy systems requires investigation of the full range of the unique environmental effects on these materials. Hydrogen isotopes are common gaseous species in nuclear reactors and exhibit ample high mobility in most materials. While hydrogen isotopes mobility in wrought stainless steel is well understood, this property is not thoroughly studied for its additively manufactured variants. In this study, we investigated the deuterium permeation and retention in 316L stainless steel manufactured by laser powder bed fusion. The results showed that the deuterium permeability in the as-built additively manufactured 316L stainless steel (AM SS316L) is greater than that of the reference wrought 316L stainless steel by a factor of 2.8. However, the stress-relieved and solution-annealed AM SS316L samples exhibit lower deuterium permeability in comparison with the as-built condition. Following the solution annealing, the deuterium permeability of AM SS316L is comparable with that of the reference wrought SS316L. Deuterium retention in the as-built AM SS316L is 45% higher than that of the wrought 316L stainless steel and slightly higher than that of the two thermally annealed AM SS316L materials. Finally, transmission electron microscopy and positron annihilation lifetime spectroscopy were used to obtain microstructural information used to determine deuterium permeation and retention behavior in the studied materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Chemical heterogeneity modulated zero thermal expansion alloy over super-wide temperature range

Chemical heterogeneity is usually avoided in solution chemistry, but it may still occur with sometimes dramatic effects on target materials and their properties. Here, we propose chemical heterogeneity as a counterintuitive strategy to design high-performance zero thermal expansion (ZTE) alloys. We apply this approach in a Hf-Ti-Fe alloy with excess Fe in the Hf/Ti sublattice and produce Hf/Ti concentration alternations at the micro level. Such chemical heterogeneity regulates local magnetic interactions in alloy and triggers a dispersed magnetic phase transition that modulates the thermal expansions at the micro level and hence results in a remarkable ZTE behavior over a super-wide temperature window from 10 to 480 K. This mechanism is supported by comprehensive studies on morphological microstructures, crystal and magnetic structures, and theoretical calculations. The strategy of local chemical heterogeneity opens up an avenue to design ZTE and the related functional materials directly via microstructure engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Rietveld Refinement for Macromolecular Powder Diffraction

Powder X-ray diffraction (PXRD) has been employed extensively for the structural characterization of materials, quantitative analysis of multicomponent mixtures, phase identification, texture, and microstructural analysis. At the heart of all those lies the Rietveld method, which has revolutionized the use of powder diffraction for materials studies. Initially applied to minerals and inorganics, the Rietveld method has progressively been used for more complex materials, for instance, zeolites and pharmaceuticals. A major advance of the method came some 20 years ago, when the first protein structure was successfully refined. Because of the sheer complexity of macromolecules, several new approaches and algorithms had to be pioneered or adapted from macromolecular single-crystal diffraction experiments, thus constituting macromolecular PXRD a quite unique field of study. This review aims to provide necessary elements of theory and application of structure solution and refinement via the Rietveld method for macromolecular PXRD data. Here, practical explanations and highlighted case studies are also presented.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Assessment of Process Modeling Tools for Determining Variability in Additively Manufactured Parts

The Advanced Materials and Manufacturing Technologies (AMMT) program aims to accelerate the development, qualification, demonstration, and deployment of advanced materials and manufacturing technologies to enable reliable and economical nuclear energy However, the unique aspects of additive manufacturing (AM) materials in terms of their processing history, microstructure, and properties, are a major barrier for qualification and certification of nuclear components. Much of this challenge may be attributed to component scale variations in microstructure and properties that are driven by local influences of process conditions and geometry on thermal history, melt pool dynamics, and corresponding microstructure evolution. Computational modeling tools may be helpful in this regard to aid in predicting and controlling this level of variability. The purpose of this report is to review the current state-of-the-art for process modeling with regards to metal AM. For this purpose, we consider specifically the case study of laser powder bed fusion (LPBF) processing of SS316, a family of alloys that are both commonly used in nuclear energy applications and suitable for AM processing. The report first introduces the necessary components of a process modeling workflow, followed by a review of the current status of each. At the end, application of these modeling tools to understanding variability in AM process given their current state are considered, and recommendations for future development are proposed

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of low-temperature neutron irradiation on the microstructure and tensile properties of duplex 2304 stainless steel and its electron-beam welds

A lean duplex stainless steel material (2304-grade) in its base metal and electron beam (e-beam) welded conditions were studied microstructurally and mechanically as a function of irradiation conditions to evaluate its use as a structural material at low temperatures (60–100 °C). Neutron irradiation up to a fluence of 1.40 × 10 19 n/cm 2 (E > 0.1 MeV) or ~0.011 dpa decreased the total elongation of both base metal and e-beam welded samples. Overall, radiation hardening was observed in all the samples. The transversely cut irradiated samples showed some nonuniform quasi-cleavage and shearing in their fracture surfaces, indicating the variance of ductile nature of the two-phased (deformable austenite and harder ferrite) duplex structure. The e-beam welded samples also showed quasi-cleavage fracture, which is a characteristic of radiation-induced embrittlement. Furthermore, these observations of the e-beam welded samples were attributed to the formation of coarse ferrites, grain boundary and intragranular phases such as γ 2 and γ 3 , and minor impurity phases such as CrN and Cr 2 N in the weld pool and/or heat-affected zone of the samples. Radiation-induced elemental segregation was also identified in the post-irradiated base metal.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fusion Blanket and Fuel Cycle Research at PNNL: FY22 Year-end Report

During the reporting period, research at PNNL focused on two tasks within the DOE Fusion Blanket and Fuel Cycle Program. Research on Task 1, Tritium Extraction from Pb-Li and He Using a Vacuum Permeator, focused on atomistic modeling to better understand tritium transport in Pd-coated V vacuum permeators. As a lower cost alternative to Pd permeators, thin coatings of Pd (or other noble metals) can be deposited over a substrate like V. However, the permeation performance of composite metal membranes degrades over time, due to the formation of intermetallics at the coating-substrate interface. Computational studies were performed to better understand tritium transport through these Pd-V intermetallics. The results of the FY22 Pd-V modeling study were recently submitted for publication in Computational Materials Science and presented at the Technology of Fusion Energy conference. Future work in this area will focus on interdiffusion barriers to prevent intermetallic formation that is deleterious to tritium transport. There are opportunities for collaboration with researchers at the Colorado School of Mines, who are manufacturing and testing candidate interdiffusion barriers. Research on Task 3, Solid Breeder Materials, included ion irradiation and post-irradiation characterization of lithium orthosilicate (Li 4 SiO 4 ) and lithium metasilicate (Li 2 SiO 3 ) to improve fundamental understanding of irradiation effects, in combination with atomistic modeling focused on the energetics of He clustering in these two ceramic phases. The results of the study suggested that the Li 4 SiO 4 phase, which is more desirable as a solid breeder due to its higher Li density, was amorphized during ion irradiation while the Li 2 SiO 3 phase appeared to be more resistant to irradiation damage. It is possible that Li loss contributed to the poor irradiation performance of the Li 4 SiO 4 , and some thoughts are provided regarding coatings that could be applied to solid breeders like this to prevent Li loss at elevated temperature while not hindering tritium diffusion. The results of the FY22 ion irradiation study were recently submitted for publication in Journal of Nuclear Materials and presented at the 22nd International Conference on Ion Beam Modification of Materials. Future work in this area will focus on Li-rich ceramics such as Li 5 AlO 4 and Li 8 ZrO 6 that have high Li density and should provide rapid tritium release based on previous work with less Li-rich ceramics.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Nanoscale defect evaluation framework combining real-time transmission electron microscopy and integrated machine learning-particle filter estimation

Observation of dynamic processes by transmission electron microscopy (TEM) is an attractive technique to experimentally analyze materials’ nanoscale phenomena and understand the microstructure-properties relationships in nanoscale. Even if spatial and temporal resolutions of real-time TEM increase significantly, it is still difficult to say that the researchers quantitatively evaluate the dynamic behavior of defects. Images in TEM video are a two-dimensional projection of three-dimensional space phenomena, thus missing information must be existed that makes image’s uniquely accurate interpretation challenging. Therefore, even though they are still a clustering high-dimensional data and can be compressed to two-dimensional, conventional statistical methods for analyzing images may not be powerful enough to track nanoscale behavior by removing various artifacts associated with experiment; and automated and unbiased processing tools for such big-data are becoming mission-critical to discover knowledge about unforeseen behavior. We have developed a method to quantitative image analysis framework to resolve these problems, in which machine learning and particle filter estimation are uniquely combined. The quantitative and automated measurement of the dislocation velocity in an Fe-31Mn-3Al-3Si autunitic steel subjected to the tensile deformation was performed to validate the framework, and an intermittent motion of the dislocations was quantitatively analyzed. The framework is successfully classifying, identifying and tracking nanoscale objects; these are not able to be accurately implemented by the conventional mean-path based analysis.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear Assisted Processing and Extrusion (ShAPE) of Aluminum Alloy 7075, 2024, and Al-12.4TM

The most common aluminum alloys utilized in the aerospace industry are 7075 and 2024 due to their high strength-to-weight ratio compared to advanced high strength steels and other aluminum alloys. Despite excellent performance, these aluminum alloys have seen limited use outside of the aerospace industry due in part to high cost. If high-performance aluminum extrusions could be made more cost effectively by eliminating energy intensive process steps typical of conventional extrusion, then numerous opportunities exist for more widespread adoption. A key reason for the high cost of 7075 and 2024 extrusions (25-75% higher than 6061) is their slow extrusion speed. 7075 and 2024 are limited to 2 m/min and 3.5 m/min respectively, in contrast to 6061 which can be extruded at 20–80 m/min. In addition to slow speed, aluminum alloys require numerous thermal treatments throughout the extrusion process including homogenization and pre-heating prior to extrusion, and solution heat treating and artificial aging after extrusion. Each of these steps contribute to the total energy consumed during manufacturing of extruded components. This project investigates the use of ShAPE to improve extrusion speed and reduce, or even eliminate, the typical thermal treatments for high strength aluminum alloys, all while improving material performance. The overarching goal of this project was to demonstrate that Shear Assisted Processing and Extrusion (ShAPE) can manufacture high-performance aluminum alloy tubing with lower manufacturing energy and improved mechanical properties compared to conventional extrusion. Unlike conventional extrusion where the billet is rammed against a stationary die using a strictly linear motion, the ShAPE process superimposes a rotational shear force by spinning the die while the billet is plunged. Compared to conventional linear extrusion, the ShAPE process imparts significantly more strain into the feedstock material, which enables the formation of novel microstructures. These microstructures manifest an array of property and process improvements for extrusion of high-performance aluminum alloys. The following accomplishments were achieved for this project: Extrusion of 7075 at 12.2 meters/min compared to 2 meters/min for conventional extrusion; Elimination of 7075 billet homogenization (430 °C for 20 hours) which is required prior to conventional extrusion; Elimination of 7075 billet pre-heating (400 °C for 1 hour) in a separate furnace which is required prior to conventional extrusion; Achieved 7075-T6with yield strength = 595 MPa, ultimate tensile strength = 531MPa, and elongation = 17.4% for extrusions made from unhomogenized billets. Exceeds the ASTM and ASM standard, and typical industry values; Achieved 7075-T5 (i.e., no solution heat treatment) with yield strength = 588 MPa, ultimate tensile strength = 535 MPa, and elongation = 14.8% for extrusions made from homogenized billets; Extrusion of 2024 at 7.4 meters/min compared to 3.5 meters/min for conventional extrusion; Achieved 2024-T8510 yield strength = 522 MPa, ultimate strength = 510MPa, and elongation = 7.1% for extrusions made from wrought billets. Exceeds the ASTM and ASM standard, and typical industry values; Extrusion of Al-12.4TM high-performance aluminum powder directly into tubing, in a single step, which eliminates process steps typical of powder metallurgy extrusion.

36 MATERIALS SCIENCE↗