Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MINING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

ANS MiNES 2023 Poster

The dynamic mechanical properties of four varieties of high purity graphite as well as the depth of penetration (DoP) of a small-scale shaped charge into these grades was experimentally determined. The grades chosen were PCEA, NBG-18, and NBG-25. These grades provide a wide range of physical properties: in density from 1.80 – 1.85 g/cc, in maximum particle size from 10s to 1000s of µm, and in porosity from 18% to 20%. The quasistatic and dynamic compressive strengths of each grade were determined and correlated to their physical properties. The split Hopkinson pressure bar experiments showed both the dynamic strength and dominant shear failure mechanisms. A small scale shaped charge was used to compare the resistance of graphite to hypervelocity jet impacts: the Teledyne RP-4. The RP-4 has a 1.01” outer diameter and 3.44 g of RDX with an RP-80 booster (86 mg PETN + 123 mg RDX). A select number of samples were analyzed using X-Ray Computed Tomography (XCT), allowing for the full characterization of the undisturbed wound channel. A selection of other samples were physically sectioned and wound channels mapped from the sections. In addition to DoP, the wound geometry was characterized in terms of total volume and diameter at different depths. The wound channel characteristics for each grade were correlated to the compressive strengths and physical properties. In several of the test samples, the wound channel diameter was smaller than the diameter of the shaped charge slug just behind where the slug had penetrated the sample. These results indicated that the wound geometry was dependent on the compressive hysteresis behavior of graphite.

36 MATERIALS SCIENCE↗
DOE OSTI2025

STILGAR End-of-Project Report

The Subsurface Tunnel Imaging LeveraGed by Analysis of Rayleigh wave ellipticity (STILGAR) project demonstrated an integrated geophysical approach for detecting, locating, and characterizing underground structural changes using dense seismic arrays and advanced inversion techniques. Field campaigns were conducted at two operational mines—the Redmond salt mine (Utah) and Graymont Pleasant Gap limestone mine (Pennsylvania)—providing real-world testbeds for monitoring anthropogenic subsurface activity. At the Redmond salt mine, seismic interferometry combined with back-projection inversion successfully identified continuous, low-amplitude signals from mining operations. The approach differentiated stationary from migrating anthropogenic sources, captured daily operational cycles, and validated the potential of passive seismic monitoring for remote detection of underground activity. At the Graymont Pleasant Gap mine, two dense seismic deployments in the spring and fall of 2023 generated over 4 TB of high-resolution data. Key outcomes included the relocation of 199 underground and 8 surface explosions with accuracies within tens of meters and the development of a 3D P-wave velocity model using the triple-difference tomography algorithm (tomoTD) that resolved major structural features such as the mine entrance, low-velocity tunnels, and roof-collapse areas. Ambient noise cross-correlation and back-projection analyses revealed persistent sources linked to ongoing mining activity, whereas horizontal-to-vertical spectral ratio (HVSR) and ellipticity studies confirmed stable site responses across seasons and identified soil thickness trends consistent with regional erosional and depositional processes. Checkerboard and sensitivity tests further validated the robustness of the tomographic results. Overall, the findings emphasize that although significant progress has been made in subsurface imaging, further work is needed to enhance the detection and localization of underground structures. Accurate imaging requires higher frequencies, yet anthropogenic sources tend to dominate the seismic record at those frequencies, and high-frequency surface waves are affected by higher modes that complicate interpretation. The improved detection and localization of human-induced signals enabled detailed temporal and spatial mapping of daily mine operations, demonstrating the feasibility of continuous anthropogenic source monitoring. Sensitivity to signals from nontraditional sources, such as fan operations, highlights the broader applicability of this approach to other industrial environments in which continuous and impulsive signals are present. The field campaigns produced a substantial volume of high-quality seismic data, supporting the development and testing of new methods for seismic source characterization and subsurface imaging. Future deployments should include sensors capable of recording lower frequencies to probe deeper structures, increase bandwidth to enhance resolution and sensitivity to both shallow and deep targets, and collect additional large-scale datasets to refine imaging and source characterization techniques. Moreover, conducting 3D modeling studies of seismic wavefields at higher frequencies will provide a better understanding of wave scattering and cavity–wavefield interactions in complex underground environments. In conclusion, the STILGAR project demonstrated that integrated seismic monitoring can effectively characterize underground operations, capturing both natural and anthropogenic signals. The approaches developed provide a foundation for improved detection, localization, and imaging of subsurface structures and are directly transferable to broader industrial monitoring applications.

58 GEOSCIENCES↗
DOE OSTI2023

Geogenic, Anthropogenic, and Authigenic Minerals Hosting Arsenic and Antimony in Yellowknife Bay Sediments

Abstract Yellowknife Bay (Great Slave Lake, Northwest Territories, Canada) is a water body valued by surrounding communities for its subsistence, recreational, and cultural use. Located directly downstream of the former Giant Mine and Con Mine, Yellowknife Bay has received inputs from mine waste streams enriched in arsenic (As), antimony (Sb), and metals since the late 1930s. Lake sediments in Yellowknife Bay provide a record of metal(loid) contamination from aerially deposited roaster stack emissions, mine effluent, and Giant Mine tailings. A sediment sampling program was conducted in Yellowknife Bay to characterize As and Sb mineralogy using scanning electron microscopy-mineral liberation analysis. Mineralogical analysis of As- and Sb-hosted minerals in nine sediment cores suggests that arsenic trioxide (As2O3), originally deposited during the period of peak-mining emissions, has since been transformed into authigenic sulfides (interpreted to be realgar) down core from peak-mining emissions. Arsenic has also been attenuated by iron (Fe)-oxyhydroxides and roaster-generated iron oxides up-core from peak-mining emissions, near the sediment–water interface. The Sb-bearing minerals appear to be stable in Yellowknife Bay sediments, with no conclusive evidence of post-depositional mobility having been identified. The observed prevalence of arsenic trioxide in surface sediments proximal to Giant Mine suggests that As and Sb contamination is ongoing, likely from terrestrial weathering of contaminated soils and shoreline outcrops. Arsenic-bearing oxide minerals prevalent in surface sediments may become unstable should redox conditions in the hypolimnion change; prolonged anoxia could destabilize the As hosting minerals and release As to bottom waters. Therefore, long-term monitoring of the water column, including hypolimnion conditions, in Yellowknife Bay is recommended.

Mineralogy↗
DOE OSTI2021

Reconstruction of the Room D, B, G, and Q Closure Histories at the Waste Isolation Pilot Plant

Experimental measurements of room closure in salt repositories are valuable for understanding the evolution of the underground and for validating geomechanical models. Room closure was measured during a number of experiments at the Waste Isolation Pilot Plant (WIPP) during the 1980's and 1990's. Most rooms were excavated using a multi-pass mining sequence, where each pass necessarily destroyed some of the mining sequence closure measurement points. These destroyed points were promptly reinstalled to capture the closure after the mining pass. After the room was complete, the mining sequence closure measurement stations were supplemented with remotely read closure measurement stations. Although many aspects of these experiments were thoroughly documented, the digital copies of the closure data were inadvertently destroyed, the non-trivial process of zeroing and shifting the raw closure measurements after each mining pass was not precisely described, the various closure measurements within a given room were not directly compared on the same plot, and the measurements were collected for several years longer than previously reported. Consequently, the hand-written mining sequence closure measurements for Rooms D, B, G, and Q were located in the WIPP archives, digitized, and reanalyzed for this report. The process of reconstructing the mining sequence closure histories was documented in detail and the raw data can be found in the appendices. Within the mid-section of a given room, the reconstructed closure histories were largely consistent with other mining sequence and remotely read closure histories, which builds confidence in the experiments and suggests that plane strain is an appropriate modeling assumption. The reconstructed closure histories were also reasonably consistent with previously published results, except in one notable case: the reconstructed Room Q closure histories 30 days after excavation were about 45 % less than the corresponding closures reported in Munson's 1997 capstone paper.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Thermal, RGB, and Multispectral Unexploded Ordnance Data Collection

As of May 1, 2026 Landmine contamination affects 58 countries and many hundreds of thousands of km² of land. For example, the National Mine Action Program Demining Ukraine reporting that up to 144,000 km² of territory are potentially contaminated and require survey and clearance (National Mine Action Program “Demining Ukraine,” n.d.) alone. This contamination includes mines and other explosive remnants of war and continues to constrain civilian access, agricultural use, infrastructure recovery, and broader socioeconomic activity (International Campaign to Ban Landmines–Cluster Munition Coalition [ICBL-CMC], 2024; Mine Action Review, 2024). Current response activities rely on established mine-action approaches including non-technical survey, technical survey, clearance, and explosive ordnance disposal, consistent with international mine-action terminology and operational practice (United Nations Mine Action Service [UNMAS], 2024; Geneva International Centre for Humanitarian Demining [GICHD], 2023). In this context, UAV-based sensing, including UAV-mounted thermal imaging, may provide a useful supplementary capability by supporting faster, safer detection and mapping of suspect hazards prior to ground intervention (Smiljanic, 2022).

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
NASA NTRS2005

A Testbed Demonstration of an Intelligent Archive in a Knowledge Building System

The last decade's influx of raw data and derived geophysical parameters from several Earth observing satellites to NASA data centers has created a data-rich environment for Earth science research and applications. While advances in hardware and information management have made it possible to archive petabytes of data and distribute terabytes of data daily to a broad community of users, further progress is necessary in the transformation of data into information, and information into knowledge that can be used in particular applications in order to realize the full potential of these valuable datasets. In examining what is needed to enable this progress in the data provider environment that exists today and is expected to evolve in the next several years, we arrived at the concept of an Intelligent Archive in context of a Knowledge Building System (IA/KBS). Our prior work and associated papers investigated usage scenarios, required capabilities, system architecture, data volume issues, and supporting technologies. We identified six key capabilities of an IA/KBS: Virtual Product Generation, Significant Event Detection, Automated Data Quality Assessment, Large-Scale Data Mining, Dynamic Feedback Loop, and Data Discovery and Efficient Requesting. Among these capabilities, large-scale data mining is perceived by many in the community to be an area of technical risk. One of the main reasons for this is that standard data mining research and algorithms operate on datasets that are several orders of magnitude smaller than the actual sizes of datasets maintained by realistic earth science data archives. Therefore, we defined a test-bed activity to implement a large-scale data mining algorithm in a pseudo-operational scale environment and to examine any issues involved. The application chosen for applying the data mining algorithm is wildfire prediction over the continental U.S. This paper reports a number of observations based on our experience with this test-bed. While proof-of-concept for data mining scalability and utility has been a major goal for the research reported here, it was not the only one. The other five capabilities of an WKBS named above have been considered as well, and an assessment of the implications of our experience for these other areas will also be presented. The lessons learned through the testbed effort and presented in this paper will benefit technologists, scientists, and system operators as they consider introducing IA/KBS capabilities into production systems.

Ramapriyan, Hampapuram↗