Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LIGNITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Evaluation of activated carbon adsorbents for CO{sub 2} capture in gasification

Activated carbon adsorbents have been evaluated at high pressure, up to 4 MPa, to determine their applicability for the removal of CO{sub 2} from syngas generated from gasification. The CO{sub 2} adsorption capacity and diffusion mechanism were demonstrated to be dependent upon the adsorbent outgas conditions. Activated carbons have been demonstrated to have higher adsorption capacities than existing absorption systems up to 12 mmol g{sup -1} at 4 MPa, under strong outgas conditions. Adsorption capacities on a weight basis have been demonstrated to be correlated with the surface area and micropore volume of the materials. However, performance on a volumetric basis is less well-defined and is controlled by the form and bulk density of the adsorbent. Complete cyclic regeneration of the adsorbents has been demonstrated by pressure swing regeneration cycles. 37 refs., 8 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Crystallization of synthetic coal-petcoke slag mixtures simulating those encountered in entrained bed slagging gasifiers

Commercial entrained bed slagging gasifiers use a carbon feedstock of coal, petcoke, or combinations of them to produce CO and H{sub 2}. These carbon sources contain mineral impurities that liquefy during gasification and flow down the gasification sidewall, interacting with the refractory linear and solidifying in the cooler zones of the gasifier. Proper slag flow is critical to good gasifier operation. A hot-stage confocal scanning laser microscope (CSLM) was used to analyze the kinetic behavior of slag crystallization for a range of synthetic coal-petcoke mixtures. On the basis of the observed precipitation during cool down studies in the 1200-1700{sup o}C temperature range, a time-temperature-transformation (TTT) diagram was created. The crystallization studies were conducted with a CO/CO{sub 2} (=1.8) corresponding to a gasification PO{sub 2} of approximately 10-8 atm at 1500{sup o}C. Ash chemistries were chosen such that they correspond to coal-petcoke feedstock mixtures with coal ash amounts of 0, 10, 30, 50, 70, and 100% (by weight), with the balance being petcoke ash. The TTT diagram exhibited two crystallization areas, one above and one below 1350{sup o}C. At the nose of the higher temperature curves, karelianite (V{sub 2}O{sub 3}) crystallization occurred and was fastest for a 30% coal-petcoke ash mixture. The second nose was located below 1350{sup o}C and had spinel-type phases that formed at 1200{sup o}C, in which preferred atomic occupation at the octahedral and tetrahedral sites varied depending upon the ash composition. At 1200{sup o}C, an Al-rich spinel formed for 100% coal slag and a Fe-rich spinel formed in petcoke-enriched slags. The addition of petcoke ash to coal ash promoted crystallization in the slag, with additional crystalline phases, such as V-rich spinel, forming at the lower temperatures. These phases were not predicted using commercially available databases. 30 refs., 18 figs.

01 COAL, LIGNITE, AND PEAT↗

Temperature-programmed decomposition desorption of mercury species over activated carbon sorbents for mercury removal from coal-derived fuel gas

The mercury (Hg{sup 0}) removal process for coal-derived fuel gas in the integrated gasification combined cycle (IGCC) process will be one of the important issues for the development of a clean and highly efficient coal power generation system. Recently, iron-based sorbents, such as iron oxide (Fe{sub 2}O{sub 3}), supported iron oxides on TiO{sub 2}, and iron sulfides, were proposed as active mercury sorbents. The H{sub 2}S is one of the main impurity compounds in coal-derived fuel gas; therefore, H{sub 2}S injection is not necessary in this system. HCl is also another impurity in coal-derived fuel gas. In this study, the contribution of HCl to the mercury removal from coal-derived fuel gas by a commercial activated carbon (AC) was studied using a temperature-programmed decomposition desorption (TPDD) technique. The TPDD technique was applied to understand the decomposition characteristics of the mercury species on the sorbents. The Hg{sup 0}-removal experiments were carried out in a laboratory-scale fixed-bed reactor at 80-300{sup o}C using simulated fuel gas and a commercial AC, and the TPDD experiments were carried out in a U-tube reactor in an inert carrier gas (He or N{sub 2}) after mercury removal. The following results were obtained from this study: (1) HCl contributed to the mercury removal from the coal-derived fuel gas by the AC. (2) The mercury species captured on the AC in the HCl{sup -} and H{sub 2}S-presence system was more stable than that of the H{sub 2}S-presence system. (3) The stability of the mercury surface species formed on the AC in the H{sub 2}S-absence and HCl-presence system was similar to that of mercury chloride (HgClx) species. 25 refs., 12 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Hydrogen production through the water-gas shift reaction: thermodynamic equilibrium versus experimental results over supported Ni catalysts

This paper discusses the experimental results of the water-gas shift reaction over supported nickel catalysts in comparison to thermodynamic equilibrium composition at the same reaction conditions. The effects of different supports on the performance of H{sub 2} production over nickel-supported catalysts are also evaluated at both low and high temperatures. Ceria-promoted nickel catalyst supported on powder alumina (Ni/CeO{sub 2}-Al{sub 2}O{sub 3}) demonstrated excellent performance. The catalyst was not stable at low temperature (250{sup o}C) but showed good stability at high temperature (450{sup o}C). At 450{sup o}C, with a catalyst loading of 0.05 g, CO/S (S = steam) ratio of 1:3, and gas hourly space velocity (GHSV) - 200 L h{sup -1} g{sub cat}{sup -1}, the activity of Ni/CeO{sub 2}-Al{sub 2}O{sub 3} was 95% with a H{sub 2} yield of 52% and a H{sub 2} selectivity of 73%.

01 COAL, LIGNITE, AND PEAT↗

Recycling of rubber tires in electric arc furnace steelmaking: simultaneous combustion of metallurgical coke and rubber tyres blends

The present study investigates the effect of addition of waste rubber tires on the combustion behavior of its blends with coke for carbon injection in electric arc furnace steelmaking. Waste rubber tires were mixed in different proportions with metallurgical coke (MC) (10:90, 20:80, 30:70) for combustion and pyrolysis at 1473 K in a drop tube furnace (DTF) and thermogravimetric analyzer (TGA), respectively. Under experimental conditions most of the rubber blends indicated higher combustion efficiencies compared to those of the constituent coke. In the early stage of combustion the weight loss rate of the blends is much faster compared to that of the raw coke due to the higher volatile yield of rubber. The presence of rubber in the blends may have had an impact upon the structure during the release and combustion of their high volatile matter (VM) and hence increased char burnout. Measurements of micropore surface area and bulk density of the chars collected after combustion support the higher combustion efficiency of the blends in comparison to coke alone. The surface morphology of the 30% rubber blend revealed pores in the residual char that might be attributed to volatile evolution during high temperature reaction in oxygen atmosphere. Physical properties and VM appear to have a major effect upon the measured combustion efficiency of rubber blends. The study demonstrates that waste rubber tires can be successfully co-injected with metallurgical coke in electric arc furnace steelmaking process to provide additional energy from combustion. 44 refs., 11 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Kinetic model of product distribution over Fe catalyst for Fischer-Tropsch synthesis

A new kinetic model of the Fischer-Tropsch synthesis (FTS) is proposed to describe the non-Anderson-Schulz-Flory (ASF) product distribution. The model is based on the double-polymerization monomers hypothesis, in which the surface C{sub 2}{asterisk} species acts as a chain-growth monomer in the light-product range, while C{sub 1}{asterisk} species acts as a chain-growth monomer in the heavy-product range. The detailed kinetic model in the Langmuir-Hinshelwood-Hougen-Watson type based on the elementary reactions is derived for FTS and the water-gas-shift reaction. Kinetic model candidates are evaluated by minimization of multiresponse objective functions with a genetic algorithm approach. The model of hydrocarbon product distribution is consistent with experimental data (<C{sub 45}). The new model gives a sound interpretation of the experimental data. 49 refs., 3 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Mineralogical characterization of Sasol feed coals and corresponding gasification ash constituents

Feed coal and coarse ash particles (heated rock fragments and clinkers), produced from Sasol-Lurgi gasifier tests under different operating conditions, have been characterized by quantitative X-ray diffraction, electron microprobe analysis, and associated chemical techniques, as a basis for better understanding of the relations between the mineralogical and physical properties of the ash particles. Crystalline phases in the ashes include quartz particles inherited directly from the feed coal, as well as anorthite, mullite, and diopside, derived from solid-state reactions or crystallization of a silicate melt during the gasification process. Glass, cooled from the melt, is also abundant in the ash materials. The abundance of large particles of hard minerals in the coal or the ash, such as quartz, anorthite, pyrite, and diopside, has been correlated with a laboratory-determined abrasion index and may contribute significantly to wear on mechanical equipment during coal- or ash-handling operations. 21 refs., 3 figs., 9 tabs.

01 COAL, LIGNITE, AND PEAT↗

Simulation of NOx emission in circulating fluidized beds burning low-grade fuels

Nitrogen oxides are a major environmental pollutant resulting from combustion. This paper presents a modeling study of pollutant NOx emission resulting from low-grade fuel combustion in a circulating fluidized bed. The simulation model accounts for the axial and radial distribution of NOx emission in a circulating fluidized bed (CFB). The model results are compared with and validated against experimental data both for small-size and industrial-size CFBs that use different types of low-grade fuels given in the literature. The present study proves that CFB combustion demonstrated by both experimental data and model predictions produces low and acceptable levels of NOx emissions resulting from the combustion of low-grade fuels. Developed model can also investigate the effects of different operational parameters on overall NOx emission. As a result of this investigation, both experimental data and model predictions show that NOx emission increases with the bed temperature but decreases with excess air if other parameters are kept unchanged. 37 refs., 5 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Influence of the precursor metamorphism degree on preparation of nitrogen-enriched activated carbons by ammoxidation and chemical activation of coals

The paper presents results of a study on obtaining N-enriched active carbons from four hard coals with different degree of metamorphism. The starting materials were carbonized, activated with KOH, and ammoxidized by a mixture of ammonia and air at the ratio 1:3 at 300 and 350{sup o}C, at each stage of the active carbon production. The efficiency of ammoxidation was found to depend on the degree of metamorphism of the precursor, the stage of processing at which ammoxidation is performed, and the temperature of this process. Ammoxidation of the active carbon led to a decrease in their surface area and pore volume, whereas that performed both at the stage of the precursor and the carbonizate brought improvement of textural parameters of the active carbons obtained. The sequence of the carbonization, activation, and ammoxidation processes had a significant effect on the acid-base character of the active carbon samples obtained. The majority of the active carbons modified at the stage of precursor and carbonizate showed considerable prevalence of surface acidic groups, whereas the samples ammoxidized after activation showed an intermediate acidic-basic character of the surface. 25 refs., 4 figs., 9 tabs.

01 COAL, LIGNITE, AND PEAT↗

Limestone calcination with CO{sub 2} capture (III): characteristics of coal combustion during limestone decomposition

In this study, the combustion characteristics of coal in CO{sub 2}/O{sub 2} and steam/CO{sub 2}/O{sub 2} atmospheres were investigated during limestone decomposition in a continuously operating fluidized bed reactor for CO{sub 2} capture. The results show that the variations and concentrations of CO, CH{sub 4}, and H{sub 2} in the exhaust gas of the reactor in the steam/CO{sub 2}/O{sub 2} atmosphere were smaller than those in the CO{sub 2}/O{sub 2} atmosphere. Because of steam dilution, the CO{sub 2} concentration in the bed was lower in the steam/CO{sub 2}/O{sub 2} atmosphere than that in the CO{sub 2}/O{sub 2} atmosphere, and the effect of differential pressure variation on limestone decomposition in the fluidized bed was less pronounced in the steam/CO{sub 2}/O{sub 2} atmosphere than that in the CO{sub 2}/O{sub 2} atmosphere. Additionally, N{sub 2}O emission was detected only in the CO{sub 2}/O{sub 2} atmosphere, and the conversion of N to NO in the steam dilution atmosphere was of a smaller magnitude than that observed in the CO{sub 2}/O{sub 2} atmosphere. We also found that the conversion of S to SO{sub 2} in the steam/CO{sub 2}/O{sub 2} atmosphere was lower than that observed in the CO{sub 2}/O{sub 2} atmosphere. The contents of sulfur, SiO{sub 2}, and Al{sub 2}O{sub 3} were much higher in solid samples located in the cyclone than in the overflow holder in both steam/CO{sub 2}/O{sub 2} and CO{sub 2}/O{sub 2} atmospheres. Finally, the hydration and carbonation reactivities of CaO produced in the steam/CO{sub 2}/O{sub 2} atmosphere were better than those produced in the CO{sub 2}/O{sub 2} atmosphere. 13 refs., 14 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Potential of two-stage membrane system with recycle stream for CO{sub 2} capture from postcombustion gas

In order to restrict greenhouse gases emissions, CO{sub 2} should be captured from the postcombustion gas for further treatment, for example, geosequestration. In this work, the separation performance of the two-stage membrane system with a recycle stream was investigated using the cross-flow model. For larger CO{sub 2}/N{sub 2} selectivities that can be achieved in the lab, for example, selectivity of 52, the separation target of CO{sub 2} purity >95% and CO{sub 2} recovery >90% can be fulfilled by the two-stage system. The process cost of the two-stage membrane process was investigated. There is an optimum pressure ratio with which the capital cost and the energy cost can be balanced to minimize the total cost. Using the optimum pressure ratios and efficient membranes, the total cost of the two-stage system can be reduced to a range that is competitive with the process cost of the traditional chemical absorption method. For example, with feed compression applied, the total cost of the two-stage membrane system using the membrane with CO{sub 2}/N{sub 2} selectivity of 52 and CO{sub 2} permeance of 3.12 x 10{sup -3} m{sup 3} (STP) m{sup -2} s{sup -1} MPa{sup -1} is estimated to be $47.9/(ton CO{sub 2} recovered). 22 refs., 11 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Effect of moisture on adsorption isotherms and adsorption capacities of CO{sub 2} on coals

The effect of moisture on the adsorption isotherms and adsorption capacities of CO{sub 2} on Argonne Premium coals has been investigated. In some experiments a small hysteresis was observed between the adsorption and desorption isotherms. The hysteresis was absent or negligible for high-rank and as-received coals but was discernible for lower rank and dried coals. An equation that accounted for the volumetric changes when an adsorbate alters the structure of an adsorbent was employed to interpret the data. The best-fit solutions indicate that the coal volume decreases upon drying. The microscopic shrinkage estimated using helium expansion was greater than the shrinkage reported using the bed-height technique. The microscopic shrinkage was 5-10% for low-moisture medium and high-rank coals and up to 40% for low-rank coals having higher moisture contents. The CO{sub 2} swelling of coals during adsorption isotherm measurements was estimated to be about the same as the shrinkage that occurred during the moisture loss. The adsorption capacity, isosteric heat of adsorption, average pore size, and surface area of the as-received (moist) and dried Argonne coals were estimated after accounting for the volume changes. The isosteric heat of adsorption of CO{sub 2} was found to be between 23 and 25 kJ/mol for as-received coals and between 25 and 27 kJ/mol for dried coals, regardless of the rank. The degree of drying was shown to affect the adsorption capacity and the calculated surface area. For dried coals, the adsorption capacity showed the typical 'U-shape' dependence on rank whereas the as-received coals displayed a more linear dependence. A relationship is proposed to quantify the effect of moisture on the adsorption capacity. The mechanism of CO{sub 2} adsorption on moist coals and the implications of the lower adsorption capacity of wet coals to coal seam sequestration of CO{sub 2} are presented. 70 refs., 12 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Effects of acetic acid injection and operating conditions on NO emission in a vortexing fluidized bed combustor using response surface methodology

The effects of acetic acid injection and operating conditions on NO emission were investigated in a pilot scale vortexing fluidized bed combustor (VFBC), an integration of circular freeboard and a rectangular combustion chamber. Operating conditions, such as the stoichiometric oxygen in the combustion chamber, the bed temperature and the injecting location of acetic acid, were determined by means of response surface methodology (RSM), which enables the examination of parameters with a moderate number of experiments. In RSM, NO emission concentration after acetic acid injection and NO removal percentage at the exit of the VFBC are used as the objective function. The results show that the bed temperature has a more important effect on the NO emission than the injecting location of acetic acid and the stoichiometric oxygen in the combustion chamber. Meanwhile, the injecting location of acetic acid and the stoichiometric oxygen in the combustion chamber have a more important effect on the NO removal percentage than the bed temperature. NO emission can be decreased by injecting the acetic acid into the combustion chamber, and NO emission decreases with the height of the acetic acid injecting location above the distributor. On the other hand, NO removal percentage increases with the height of the acetic acid injecting location, and NO emission increases with the stoichiometric oxygen in the combustion chamber and the bed temperature. NO removal percentage increases with the stoichiometric oxygen, and increases first, then decreases with the bed temperature. Also, a higher NO removal percentage could be obtained at 850{sup o}C. 26 refs., 12 figs., 8 tabs.

01 COAL, LIGNITE, AND PEAT↗

Novel use of residue from direct coal liquefaction process

Direct coal liquefaction residue (DCLR) is, commonly, designed to be used as a feed stock for gasification or combustion. Use of DCLR as a value added product is very important for improving overall economy of direct coal liquefaction processes. This study shows that the DCLR may be used as a pavement asphalt modifier. The modification ability is similar to that of Trinidad Lake Asphalt (TLA), a superior commercial modifier. Asphalts modified by two DCLRs meet the specifications of ASTM D5710 and BSI BS-3690 designated for the TLA-modified asphalts. The required addition amount for the DCLRs tested is less than that for TLA due possibly to the high content of asphaltene in DCLRs. Different compatibility was observed for the asphalts with the same penetration grade but from the different origin. Different components in the DCLR play different roles in the modification. Positive synergetic effects among the fractions were observed, which may due to the formation of the stable colloid structure. Unlike polymer-type modifier, the structure of asphalt-type modifier has a similarity with petroleum asphalts which favors the formation of a stable dispersed polar fluid (DPF) colloid structure and improves the performance of pavement asphalt. 12 refs., 1 fig., 6 tabs.

01 COAL, LIGNITE, AND PEAT↗

Effects of metal cations present naturally in coal on the fate of coal-bound nitrogen in the fixed-bed pyrolysis of 25 coals with different ranks: correlation between inherent Fe cations and N{sub 2} formation from low-rank coals

The fate of coal-N in the fixed-bed pyrolysis of 25 coals with 62-81 wt % (daf) C has been studied with a quartz reactor at 1000 C under ambient pressure to examine the effects of metal cations present naturally in these coals on the partitioning of coal-N into N{sub 2}, NH{sub 3}, HCN, tar-N, and char-N. Nitrogen mass balances for all runs fall within the reasonable range of 100 {+-} 5%, and N{sub 2} is the predominant product for all of the coals. As the N{sub 2} yield increases, the sum of NH{sub 3}, HCN, and tar-N is unchanged significantly, whereas the char-N yield decreases almost linearly, showing that most of N{sub 2} originates from char-N. When eight kinds of inherent metals, such as Na, Mg, Al, Si, K, Ca, Fe, and Ti, are determined by the conventional method and related with the N{sub 2} yield, there exists a strong, direct correlation between the Fe content and N{sub 2} formation for low-rank coals with less than 75 wt % (daf) C. Transmission electron microscopy coupled with an energy-dispersive analysis of X-rays (TEM-EDAX) measurements after pyrolysis at 1000{sup o}C of a German brown coal, which provides the highest N{sub 2} yield of about 60%, reveal the existence of lamella structures because of graphitized carbon as well as nanoscale Fe particles with different sizes and shapes. The mechanism for conversion reactions of char-N to N{sub 2} is discussed in terms of the catalysis by nanoparticles of metallic Fe formed from inherent Fe cations. 34 refs., 18 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Experimental and modeling study on char combustion

In this study, on the basis of experimental verifications with an FTIR online measurement system, theoretical calculations by using the strict continuous-film model were first compared with those by the simple single-film model that is still widely used in mathematical modeling of pulverized coal flames. The results indicated that the single-film model has some significant errors in its predictions of the ignition temperature and the combustion following ignition and hence should have some restrictions on its application. Then an improved char combustion model has been presented, taking into consideration the influence of the finite-rate heterogeneous reduction and oxidation reactions. This model gives the explicit algebraic expressions for the overall rate of combustion, the surface temperature of the particle, and the gas temperature at the flame sheet. Compared with the single-film model, predictions by the present model were in much better agreement with those predicted by the continuous-film model and the experimental data. The novel model is also much easier to be integrated into the comprehensive computing codes for industrial pulverized coal flame than the continuous-film model. 21 refs., 14 figs.

01 COAL, LIGNITE, AND PEAT↗

Effect of bed pressure drop on performance of a CFB boiler

The effect of bed pressure drop and bed inventory on the performances of a circulating fluidized bed (CFB) boiler was studied. By using the state specification design theory, the fluidization state of the gas-solids flow in the furnace of conventional CFB boilers was reconstructed to operate at a much lower bed pressure drop by reducing bed inventory and control bed quality. Through theoretical analysis, it was suggested that there would exist a theoretical optimal value of bed pressure drop, around which the boiler operation can achieve the maximal combustion efficiency and with significant reduction of the wear of the heating surface and fan energy consumption. The analysis was validated by field tests carried out in a 75 t/h CFB boiler. At full boiler load, when bed pressure drop was reduced from 7.3 to 3.2 kPa, the height of the dense zone in the lower furnace decreased, but the solid suspension density profile in the upper furnace and solid flow rate were barely influenced. Consequently, the average heat transfer coefficient in the furnace was kept nearly the same and the furnace temperature increment was less than 17{sup o}C. It was also found that the carbon content in the fly ash decreased first with decreasing bed pressure drop and then increased with further increasing bed pressure drop. The turning point with minimal carbon content was referred to as the point with optimal bed pressure drop. For this boiler, at the optimum point the bed pressure was around 5.7 kPa with the overall excess air ratio of 1.06. When the boiler was operated around this optimal point, not only the combustion efficiency was improved, but also fan energy consumption and wear of heating surface were reduced. 23 refs., 6 figs., 4 tabs.

01 COAL, LIGNITE, AND PEAT↗

Sample contamination with NMP-oxidation products and byproduct-free NMP removal from sample solutions

1-Methyl-2-pyrrolidinone (NMP) is widely used as a solvent for coal-derived products and as eluent in size exclusion chromatography. It was observed that sample contamination may take place, through reactions of NMP, during extraction under refluxing conditions and during the process of NMP evaporation to concentrate or isolate samples. In this work, product distributions from experiments carried out in contact with air and under a blanket of oxygen-free nitrogen have been compared. Gas chromatography/mass spectrometry (GC-MS) clearly shows that oxidation products form when NMP is heated in the presence of air. Upon further heating, these oxidation products appear to polymerize, forming material with large molecular masses. Potentially severe levels of interference have been encountered in the size exclusion chromatography (SEC) of actual samples. Laser desorption mass spectrometry and SEC agree in showing an upper mass limit of nearly 7000 u for a residue left after distilling 'pure' NMP in contact with air. Furthermore, experiments have shown that these effects could be completely avoided by a strict exclusion of air during the refluxing and evaporation of NMP to dryness. 45 refs., 13 figs.

01 COAL, LIGNITE, AND PEAT↗