SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Experimental and Numerical Evaluation of the Thermal-Fluid Characteristics of the Helium-Cooled Modular Divertor with Multiple Jets Using a Reversed Heat Flux Approach

A single-finger unit of the Helium-Cooled Modular Divertor with Multiple Jets (HEMJ) with a plasma-facing surface (PFS) area of about 2 cm 2 has been studied in a helium (He) loop at He mass flow rates m˙ H ≤ 8 g/s and nearly prototypical conditions. Based on previous studies of the single finger of the HEMJ, our Georgia Institute of Technology group is planning to experimentally study larger divertors. Given that the HEMJ test section was heated with an induction heater and that it is impractical to scale this up to divertors with larger PFS areas, a reversed heat flux approach is being considered to measure heat transfer coefficients (HTCs). In this approach, the direction of the heat flux is reversed with water cooling and high-temperature He heating of the outer shell attached to the PFS. This work presents an initial experimental and numerical evaluation of this approach for a single HEMJ finger. Experiments with brass and copper-chromium-zirconium outer shells were conducted at dimensionless He mass flow rates or Reynolds numbers Re = 1 × 10 4 to 4.7 × 10 4 , an inlet pressure of 10 MPa, temperatures as great as 673 K, and maximum heat flux of 8.4 MW/m 2 . The experiments verify that the He-side HTCs are independent of the direction of the heat flux. Here, the results agree well with previous Nusselt number correlation and pressure loss coefficients for the HEMJ obtained using the normal heating approach.

42 ENGINEERING↗

DOE OSTI2023

High-energy neutrino emission from magnetized jets of rapidly rotating protomagnetars

ABSTRACT Relativistic jets originating from protomagnetar central engines can lead to long duration gamma-ray bursts (GRBs) and are considered potential sources of ultra-high-energy cosmic rays and secondary neutrinos. We explore the propagation of such jets through a broad range of progenitors, from stars which have shed their envelopes to supergiants which have not. We use a semi-analytical spin-down model for the strongly magnetized and rapidly rotating protoneutron star (PNS) to investigate the role of central engine properties such as the surface dipole field strength, initial rotation period, and jet opening angle on the interactions and dynamical evolution of the jet-cocoon system. With this model, we determine the properties of the relativistic jet, the mildly relativistic cocoon, and the collimation shock in terms of system parameters such as the time-dependent jet luminosity, injection angle, and density profile of the stellar medium. We also analyse the criteria for a successful jet breakout, the maximum energy that can be deposited into the cocoon by the relativistic jet, and structural stability of the magnetized outflow relative to local instabilities. Lastly, we compute the high-energy neutrino emission as these magnetized outflows burrow through their progenitors. Precursor neutrinos from successful GRB jets are unlikely to be detected by IceCube, which is consistent with the results of previous works. On the other hand, we find that high-energy neutrinos may be produced for extended progenitors like blue and red supergiants, and we estimate the detectability of neutrinos with next generation detectors such as IceCube-Gen2.

Astronomy & Astrophysics↗

NASA NTRS2002

Prediction of the Acoustic Field Associated with Instability Wave Source Model for a Compressible Jet

This paper provides preliminary results of the study of the acoustic radiation from the source model representing spatially-growing instability waves in a round jet at high speeds. The source model is briefly discussed first followed by the analysis of the produced acoustic directivity pattern. Two integral surface techniques are discussed and compared for prediction of the jet acoustic radiation field.

Golubev, Vladimir↗

DOE OSTI2021

Increasing large wildfires over the western United States linked to diminishing sea ice in the Arctic

Abstract The compound nature of large wildfires in combination with complex physical and biophysical processes affecting variations in hydroclimate and fuel conditions makes it difficult to directly connect wildfire changes over fire-prone regions like the western United States (U.S.) with anthropogenic climate change. Here we show that increasing large wildfires during autumn over the western U.S. are fueled by more fire-favorable weather associated with declines in Arctic sea ice during preceding months on both interannual and interdecadal time scales. Our analysis (based on observations, climate model sensitivity experiments, and a multi-model ensemble of climate simulations) demonstrates and explains the Arctic-driven teleconnection through regional circulation changes with the poleward-shifted polar jet stream and enhanced fire-favorable surface weather conditions. The fire weather changes driven by declining Arctic sea ice during the past four decades are of similar magnitude to other leading modes of climate variability such as the El Niño-Southern Oscillation that also influence fire weather in the western U.S.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Elucidating size effects on the yield strength of single-crystal Cu via the Richtmyer–Meshkov instability

Capturing the dynamic response of a material under high strain-rate deformation often demands challenging and time consuming experimental effort. While shock hydrodynamic simulation methods can aid in this area, a priori characterizations of the material strength under shock loading and spall failure are needed in order to parameterize constitutive models needed for these computational tools. Moreover, parameterizations of strain-rate-dependent strength models are needed to capture the full suite of Richtmyer–Meshkov instability (RMI) behavior of shock compressed metals, creating an unrealistic demand for these training data solely on experiments. Herein, we sweep a large range of geometric, crystallographic, and shock conditions within molecular dynamics (MD) simulations and demonstrate the breadth of RMI in Cu that can be captured from the atomic scale. In this work, yield strength measurements from jetted and arrested material from a sinusoidal surface perturbation were quantified as Y RMI = 0.787 ± 0.374 GPa, higher than strain-rate-independent models used in experimentally matched hydrodynamic simulations. Defect-free, single-crystal Cu samples used in MD will overestimate Y RMI , but the drastic scale difference between experiment and MD is highlighted by high confidence neighborhood clustering predictions of RMI characterizations, yielding incorrect classifications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS1972

Impact of subsonic aerodynamic considerations on a space shuttle booster configuration

Considerations of cruise-back efficiency and subsonic flying qualities are shown to have resulted in a configuration with an aft high wing of moderate aspect ratio and with vertical tails located at the wing tips. The need to protect the air breathing engines during ascent and reentry and the desire for a low trim penalty longitudinal control surface led to consideration of a jet-flap canard. The advantages of this application of STOL technology to a space system are examined and the results of both wind tunnel tests and flight simulations are discussed. Since the use of the jet-flap canard concept offers the potential for a minimum weight vehicle, a proposed technology development program is outlined in order that the full benefit of this concept may be realized.

Roensch, R. L.↗

NASA NTRS1973

Effect of wing aspect ratio and flap span on aerodynamic characteristics of an externally blown jet-flap STOL model

An investigation has been conducted to determine the effects of flap span and wing aspect ratio on the static longitudinal aerodynamic characteristics and chordwise and spanwise pressure distributions on the wing and trailing-edge flap of a straight-wing STOL model having an externally blown jet flap without vertical and horizontal tail surfaces. The force tests were made over an angle-of-attack range for several thrust coefficients and two flap deflections. The pressure data are presented as tabulated and plotted chordwise pressure-distribution coefficients for angles of attack of 1 and 16. Pressure-distribution measurements were made at several spanwise stations.

Smith, C. C., Jr.↗

NASA NTRS1975

Augmentation of vortex lift by spanwise blowing

An investigation has been conducted to evaluate the aerodynamic effects associated with blowing a jet spanwise over a wing's upper surface in a direction parallel to the leading edge. Experimental pressure and force data were obtained on wings with sweep angles of 30 and 45 degrees and showed that spanwise blowing aids in the formation and control of the leading-edge vortex and, hence, significantly improves the aerodynamic characteristics at high angles of attack. Full vortex section lift is achieved at the inboard span station with a small blowing rate, but successively higher blowing rates are necessary to attain the full vortex-lift level at increased span distances. Spanwise blowing generates large increases in lift at high angles of attack, improves the drag polars, and extends the linear pitching moment to high lifts.

Campbell, J. F.↗

NASA NTRS1976

Effects of perforated flap surfaces and screens on acoustics of a large externally blown flap model

Various model geometries and combinations of perforated flap surfaces and screens mounted close to the flap surfaces were studied for application to jet-flap noise attenuation for externally blown flap, under-the-wing aircraft. The efforts to reduce jet-flap interaction noise were marginally successful. Maximum attenuations of less than 4 db in overall sound pressure level were obtained in the flyover plane. Noise reductions obtained in the low-to-middle-frequency ranges (up to 7 db) were generally offset by large increases in high-frequency noise (up to 20 db).

Burns, R. J.↗

NASA NTRS1977

Analysis and documentation of QCSEE (Quiet Clean Short-haul Experimental Engine) over-the-wing exhaust system development

A static scale model test program was conducted in the static test area of the NASA-Langley 9.14- by 18.29 m(30- by 60-ft) Full-Scale Wind Tunnel Facility to develop an over-the-wing (OTW) nozzle and reverser configuration for the Quiet Clean Short-Haul Experimental Engine (QCSEE). Three nozzles and one basic reverser configuration were tested over the QCSEE takeoff and approach power nozzle pressure ratio range between 1.1 and 1.3. The models were scaled to 8.53% of QCSEE engine size and tested behind two 13.97-cm (5.5-in.) diameter tip-turbine-driven fan simulators coupled in tandem. An OTW nozzle and reverser configuration was identified which satisfies the QCSEE experimental engine requirements in terms of nozzle cycle area variation capability and reverse thrust level, and provides good jet flow spreading over a wing upper surface for achievement of high propulsive lift performance.

Ammer, R. C.↗

NASA NTRS1977

Numerical prediction of aeroacoustic jet-flap flows

Turbulent boundary layer flows departing an aerodynamic surface are experimentally verified to be strong sources of noise. Analysis of the source tensor of the Lighthill equation identifies important gradients of mean and fluctuating velocity components. Transition distributions of mean flow and select fluctuating velocity correlations, within the region immediately downstream of a sharp edged flap terminus are established by finite element solution of a parabolized form of the time-averaged steady flow Navier-Stokes equations closed with a turbulence kinetic energy model. Numerical solutions are presented which quantize the localized large mean flow accelerations and resultant peaks in the distribution of turbulence kinetic energy in the near wake region. Results are verified by comparison to experiment.

Baker, A. J.↗

NASA NTRS1978

Aerodynamic preliminary analysis system. Part 1: Theory

A comprehensive aerodynamic analysis program based on linearized potential theory is described. The solution treats thickness and attitude problems at subsonic and supersonic speeds. Three dimensional configurations with or without jet flaps having multiple non-planar surfaces of arbitrary planform and open or closed slender bodies of non-circular contour may be analyzed. Longitudinal and lateral-directional static and rotary derivative solutions may be generated. The analysis was implemented on a time sharing system in conjunction with an input tablet digitizer and an interactive graphics input/output display and editing terminal to maximize its responsiveness to the preliminary analysis problem. Nominal case computation time of 45 CPU seconds on the CDC 175 for a 200 panel simulation indicates the program provides an efficient analysis for systematically performing various aerodynamic configuration tradeoff and evaluation studies.

Bonner, E.↗

NASA NTRS1983

The Concorde and aeronautical research

Theoretical and experimental work carried out in various research centers, and particularly at ONERA, which led to the conception and to the main technical solutions included in the design of Concorde: plane form, twist and camber of the wing, lift augmentation by upper surface vortices, kinetic heating, air intakes and jet exhausts, materials, aeroelasticity. The development of research, and the numerous tests carried out for the benefit of the designers since the beginning of the project, are also outlined.

Salmon, M.↗

NASA NTRS1993

Transient current interruption mechanism in a magnetically delayed vacuum switch

The capacity of a magnetically delayed vacuum switch to conduct current depends on the density of plasma injected into the switch. Exceeding the current capacity results in the switch entering a lossy mode of operation characterized by a transient interruption of the main current (opening behavior) and a rapid increase of voltage across the vacuum gap. Streak and framing photographs of the discharge indicate that a decrease of luminosity near the middle of the gap preceeds the transition to the opening phase. The zone of low luminosity propagates toward the cathode. This evidence suggests that the mechanism causing the opening phase is erosion of the background plasma in a manner similar to that in a plasma-opening switch. The resulting ion depletion forces a space-charge-limited conduction mode. The switch inductance maintains a high discharge current even during the space-charge-limited conduction phase, thus producing high internal fields. The high accelerating voltage, in turn, produces electron and ion beams that heat the electrode surfaces. As a result of the heating, jets of electrode vapor issue from the electrodes, either cathode or anode, depending on the selection of electrode materials.

Morris, Gibson, Jr.↗

NASA NTRS1993

Implementation of ADI: Schemes on MIMD parallel computers

In order to simulate the effects of the impingement of hot exhaust jets of High Performance Aircraft on landing surfaces a multi-disciplinary computation coupling flow dynamics to heat conduction in the runway needs to be carried out. Such simulations, which are essentially unsteady, require very large computational power in order to be completed within a reasonable time frame of the order of an hour. Such power can be furnished by the latest generation of massively parallel computers. These remove the bottleneck of ever more congested data paths to one or a few highly specialized central processing units (CPU's) by having many off-the-shelf CPU's work independently on their own data, and exchange information only when needed. During the past year the first phase of this project was completed, in which the optimal strategy for mapping an ADI-algorithm for the three dimensional unsteady heat equation to a MIMD parallel computer was identified. This was done by implementing and comparing three different domain decomposition techniques that define the tasks for the CPU's in the parallel machine. These implementations were done for a Cartesian grid and Dirichlet boundary conditions. The most promising technique was then used to implement the heat equation solver on a general curvilinear grid with a suite of nontrivial boundary conditions. Finally, this technique was also used to implement the Scalar Penta-diagonal (SP) benchmark, which was taken from the NAS Parallel Benchmarks report. All implementations were done in the programming language C on the Intel iPSC/860 computer.

Vanderwijngaart, Rob F.↗

NASA NTRS1994

Multi-partitioning for ADI-schemes on message passing architectures

A kind of discrete-operator splitting called Alternating Direction Implicit (ADI) has been found to be useful in simulating fluid flow problems. In particular, it is being used to study the effects of hot exhaust jets from high performance aircraft on landing surfaces. Decomposition techniques that minimize load imbalance and message-passing frequency are described. Three strategies that are investigated for implementing the NAS Scalar Penta-diagonal Parallel Benchmark (SP) are transposition, pipelined Gaussian elimination, and multipartitioning. The multipartitioning strategy, which was used on Ethernet, was found to be the most efficient, although it was considered only a moderate success because of Ethernet's limited communication properties. The efficiency derived largely from the coarse granularity of the strategy, which reduced latencies and allowed overlap of communication and computation.

Vanderwijngaart, Rob F.↗

NASA NTRS2004

[CO2 Budget and Atmospheric Rectification (COBRA) Over North America]

The purpose of the CO2 Budget and Rectification Airborne (COBRA) study was to assess terrestrial sources and sinks of carbon dioxide using an air-borne study. The study was designed to address the measurement gap between plot-scale direct flux measurements and background hemispheric-scale constraints and to refine techniques for measuring terrestrial fluxes at regional to continental scales. The initial funded effort (reported on here) was to involve two air-borne campaigns over North America, one in summer and one in winter. Measurements for COBRA (given the acronym C02BAR in the initial proposal) were conducted from the University of North Dakota Citation 11, a twin-engine jet aircraft capable of profiling from the surface to 12 km and cruising for up to 4 hours and 175m/s. Onboard instrumentation measured concentrations of CO2, CO, and H2O, and meteorological parameters at high rates. In addition, two separate flask sampling systems collected discrete samples for laboratory analysis of CO2,CO, CH4, N2O, SF6, H2, 13CO2, C18O16O,O2/N2, and Ar/N2. The project involved a collaboration between a number of institutions, including (but not limited to) Harvard, NOAA-CMDL, the University of North Dakota, and Scripps.

Source record↗

NASA NTRS2004

Streaming Clumps Ejection Model and the Heterogeneous Inner Coma of Comet Wild 2

The conventional concept of cometary comae is that they are dominated by fine particulates released individually by sublimation of surface volatiles and subsequent entrainment in the near-surface gas. It has long been recognized that such particulates could be relatively large, with early estimates that objects perhaps up to one meter in size may be levitated from the surface of the typical cometary nucleus. However, the general uniformity and small average particulate size of observed comae and the relatively smooth, monotonic increases and decreases in particle density during the Giotto flythrough of comet Halley s coma in 1986 reinforced the view that the bulk of the particles are released at the surface, are fine-sized and inert. Jets have been interpreted as geometrically constrained release of these particulates. With major heterogeneities observed during the recent flythrough of the inner coma of comet Wild 2, these views deserve reconsideration.

Clark, B. C.↗