Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELECTRODEPOSITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Electrochemical deposition of amorphous aluminum oxides on lead pipes to prevent lead leaching into the drinking water

Over 5000 public drinking water systems in the US are out of compliance with the Lead and Copper Rule. Lead leaching from lead pipes is limited by the solubility of a naturally occurring scale. Changes in water quality may cause this scale to become more soluble, releasing lead into the drinking water. We propose a novel electrochemical method to prevent lead leaching from lead pipes. In this method, an aluminum wire and an alkaline phosphate electrolyte are inserted into the pipes. The pipes are then anodized for 2 h by using an external power supply, resulting in the electrodeposition of an insoluble aluminum oxide layer on top of the preexisting scale. This technology was tested on lead pipes from the EBMUD water distribution systems located in Berkeley, CA, using recirculating synthetic and actual tap water for 120 days. The untreated pipes leached an average of 23 ppb and 38 ppb of lead respectively, when using free chlorine and monochloramine as disinfection residuals. In contrast, the treated pipes leached 3 ppb and 5 ppb respectively. These results suggest that the proposed treatment has the potential to prevent lead leaching regardless of the disinfection residual and thus should be further explored in a field trial.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Optimization of the magnetocaloric effect in arrays of Ni 3 Pt nanomagnets

Structural parameters of nanomagnet arrays have been systematically adjusted in order to study and to maximize the magnetocaloric effect. Optimum technological parameters were experimentally established and arrays of nanomagnets based on Ni 3 Pt nanoparticles with a different structure period (1, 2, 3μm) and two different heights (1.2 and 1.9μm) were fabricated using electron-beam lithography followed by electrodeposition. The obtained arrays have a phase composition of fcc-Ni 3 Pt, which remains unchanged after annealing. It was shown that a change in the period of the nanomagnet arrays leads to a change in the magnitude of the magnetocaloric effect and the operating temperature range. Furthermore, changes in the height of nanomagnets from 1.2 to 1.9μm lead to an increase in the magnetocaloric response by more than 30%.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Integration of high capacity materials into interdigitated mesostructured electrodes for high energy and high power density primary microbatteries

Microbatteries are increasingly important for powering electronic systems, however, the volumetric energy density of microbatteries lags behind that of conventional format batteries. This paper reports a primary microbattery with energy density 45.5 μWh cm –2 μm –1 and peak power 5300 μW cm –2 μm –1 , enabled by the integration of large volume fractions of high capacity anode and cathode chemistry into porous micro-architectures. The interdigitated battery electrodes consist of a lithium metal anode and a mesoporous manganese oxide cathode. The key enabler of the high energy and power density is the integration of the high capacity manganese oxide conversion chemistry into a mesostructured high power interdigitated bicontinuous cathode architecture and an electrodeposited dense lithium metal anode. Here, the resultant energy density is greater than previously reported three-dimensional microbatteries and is comparable to commercial conventional format lithium-based batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Constitutional under-potential plating (CUP) – New insights for predicting the morphological stability of deposited lithium anodes in lithium metal batteries

Lithium (Li) cycling in lithium metal batteries (LMBs) inevitably witnesses a non-planar Li/electrolyte interface (cellular/dendritic microstructure) affecting the performance, safety and reliability of LMBs. Herein, the “constitutional under-potential plating” (CUP) concept is presented for the first time to understand the evolution, formation and predict the morphological stability/instability of the Li/electrolyte interface. Here, the CUP condition, a measure of the driving force for interface perturbation, occurs when the true potential gradient at the interface is smaller than the equilibrium electrodeposition potential gradient at the Li/electrolyte interface resulting in the electrolyte ahead of the Li-electrolyte interface to be in an under-potential state. Detailed CUP criterion calculations conducted herein establishes the relationship of battery operating conditions (e.g. current density, potential gradient) with the electrolyte properties (e.g. Li-ion transference number and diffusion coefficient) predicting the morphological stability condition at the interface. In addition to the driving force for interface perturbation, the capillarity effect or the Gibbs Thomson effect, a measure of the resistance to perturbation of the perturbed interface is discussed for understanding the influence of interfacial energy/adhesion energy between the current collector and the deposited Li on the overall morphological stability of the Li/electrolyte interface, a critical criterion for the unwanted dendritic morphology.

25 ENERGY STORAGE↗
DOE OSTI2020

Correlating capacity fade with film resistance loss in fast charging of lithium-ion battery

Fast charging of lithium-ion (Li-ion) batteries makes it susceptible to lithium plating. Here, we report the correlation between capacity loss and cell impedance changes in the battery due to lithium electrodeposition. Li-ion pouch cells with nickel-manganese-cobalt cathode and graphite anode were charged at rates varying from 0.5C to 6C. The cell voltage evolution immediately after charging was monitored to identify the C-rates that result in lithium plating. Electrochemical impedance spectroscopy (EIS) was used to monitor the cell impedance evolution. The impedance of battery cells at C-rates lower than 1C and no lithium plating showed minimal changes from their baseline values in the period immediately after charging. However, the impedance of battery cells undergoing lithium plating and C-rates higher than 3C showed a substantial reduction immediately after charging, with recovery back to baseline values after 30 min of relaxation. These observations suggest that lithium plating causes damage to the solid electrolyte interface (SEI) layer on the anode particles during the charging period, followed by the reformation of the SEI during the relaxation period. The measured capacity loss has a linear correlation with observed impedance change. The linear relationship suggests that impedance monitoring may be used for prognostication of the state-of-health of Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Trace levels of PtRu on NiMo foam electrodes towards hydrogen evolution reaction

Electrochemical water splitting plays a critical role in high purity hydrogen production. To lower capital cost and energy consumption, efficient catalysts are required to boost the hydrogen evolution reaction (HER), especially in alkaline media. Although PtRu alloy materials are still considered the state-of-the-art catalyst for the HER under alkaline media, large-scale application is hindered by its scarcity and high cost. NiMo alloy catalysts can be potential Pt-free alternatives to drive the sluggish kinetics of the HER under alkaline media, but their HER activity is still not ideal due to the limitation of Volmer step. Herein, we investigated the impact of trace levels of PtRu catalysts on NiMo electrodes towards the HER by incorporating advantages of both PtRu and NiMo catalysts to minimize cost and maintain a promising HER activity. Trace levels of PtRu catalysts from 0.0173 to 0.2648 mg cm −2 were loaded on commercial NiMo foam electrodes by a facile electrodeposition technique utilizing ppm concentration levels of PtRu in electrolyte. The results show that 0.0173 mg cm −2 PtRu loading on NiMo electrode can significantly enhance HER activity compared to the pristine NiMo foam electrode (Tafel slopes drop from ∼170 to ∼60 mV dec −1 ) due to the remarkable decline of energy barriers towards water dissociation and hydrogen adsorption. Meanwhile, the rate determining step (RDS) switches from the Volmer step to the Heyrovsky step when the PtRu loading increases to 0.0675 mg cm −2 . Promising catalytic stability is observed at 100 mA cm −2 over the course of 50 h with a PtRu loading of 0.1198 mg cm −2 . In conclusion, this work demonstrates a potential strategy to decrease the cost and simultaneously maintain superior HER performance by integrating trace levels of PtRu catalyst with NiMo foam electrodes.

Electrochemical water splitting↗
DOE OSTI2023

Copper-nickel electroplating of 3D-printed acrylonitrile butadiene styrene for interference and radiation shielding applications

Here, in this study, electromagnetic and radiation shielding structures were fabricated by 3D printing acrylonitrile butadiene styrene (ABS) structures via fused filament fabrication and electroplating with copper (Cu) and nickel (Ni) metals. Prior to electroplating, the printed ABS materials were made conductive by surface electrodeposition of polypyrrole (PPy). ABS adsorbs the pyrrole monomer, which subsequently polymerizes via oxidation forming conductive PPy layer on the printed structures. The successful anchoring of PPy layer can be attributed to its hydrogen bonding and electrostatic interactions with ABS. Thermal analysis, optical, and electron microscopy equipped with energy dispersive X-ray were employed to characterize the printed shielding structures, while the interference and radiation shielding effectiveness were evaluated using a spectrum analyzer and dosimeter, respectively. The interference shielding was found to be effective at 60 ± 5 dB over relatively small frequency range. Shielding was also apparent against gamma and X-ray ionizing rays, but more significantly effective against beta rays. Furthermore, the Cu/Ni coating was able to reduce any heat-induced dimensional changes for the 3D printed ABS substrate without compromising the mechanical integrity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Excitation function of 54 Fe(p, α ) 51 Mn from 9.5 MeV to 18 MeV

Excitation function of the 54 Fe(p,α) 51 Mn reaction was measured from 9.5 to 18 MeV $E_{0,p^+}$ by activating a foil stack of 54 Fe electrodeposited on copper substrates. Residual radionuclides were quantified by HPGe gamma ray spectrometry. Both 51 Mn ($t_{1/2}$ = 46.2 min, $\langle E_{β^+}\rangle$=963.7keV, $I_{β^+}$ = 97%; $E_γ$ = 749.1keV, $I_γ$ = 0.265%) and its radioactive daughter, 51 Cr ($t_{1/2}$ = 27.704d, $E_γ$ = 320.1 keV, $I_γ$ = 9.91%), were used to indirectly quantify formation of 51 Mn. Results agree within uncertainty to the only other measurement in literature and predictions of default TALYS theoretical code. Final relative uncertainties are within ±12%.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

An electrochemical generator for the continual supply of 213 Bi from 225 Ac for use in targeted alpha therapy applications

Bismuth-213 is a radionuclide of interest for targeted alpha therapy and is supplied via a radiochemical generator system through the decay of 225 Ac. Radionuclide generators employ longer lived “parent” radionuclides to routinely supply shorter-lived “daughter” radionuclides. The traditional 225 Ac/ 213 Bi radiochemical generator relies on an organic cation exchange resin where 225 Ac binds to the resin and 213 Bi is routinely eluted. These resins degrade when they absorb large doses of ionizing radiation (>1 × 10 6 Gy/mg), which has been observed when the loading activity of 225 Ac exceeds 2.59*10 9 Bq (70 mCi). Herein we report the development of an electrochemical generator for the supply of 213Bi that has the potential to overcome this limitation. Bismuth-213 spontaneously electrodeposits onto nickel foils in 0.1 M hydrochloric acid at 70 °C. Using this method, we were able to plate an average of 73 ± 4 % of the 213 Bi in solution and obtain a final 213 Bi recovery of 65 ± 8 % in 0.1 M citrate pH 4.5 via reverse electrolysis using titanium as the cathode. The recovered 213Bi had an average radiochemical purity of >99.8 % and was successfully used to radiolabel DOTATATE with an average radiochemical yield of 85.1 % (not optimized).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Current challenges and potential directions towards precision microscale additive manufacturing – Part III: Energy induced deposition and hybrid electrochemical processes

The Part III of the four-part series of articles discusses the challenges and opportunities in microscale additive manufacturing processes, specifically focusing on energy-induced deposition and electrochemical processes. Compared to the direct ink write (DIW) and laser-based processes, the energy-induced deposition methods can fabricate high-resolution, high aspect ratio and complex parts, while the hybrid electrochemical process can be used to fabricate complex parts using a wide range of conductive and photoactive materials. However, the volumetric throughput of these processes is lower than their DIW and laser-based counterparts. The processes that have been explored in this process are Focused-ion Beam Induced Deposition (FIBID), Laser Chemical Vapor Deposition (LCVD), Menicus-confined Electrodeposition (MCED) and Laser-Enabled Electrochemical Printing (LECP). The range of processable materials, feature-size resolution, geometry and volumetric throughput are used as factors to evaluate the current state-of-the-art for these processes. Finally, novel approaches have been proposed in the article to address these challenges associated with microscale AM processes.

42 ENGINEERING↗
DOE OSTI2022

Novel fractal-textured solar absorber surfaces for concentrated solar power

The solar absorptance of a thermal receiver surface significantly affects the photothermal conversion efficiency of concentrated solar power (CSP) plants. The development of low-cost Gen3 CSP systems calls for increasing the solar absorptance of the thermal receivers at operating temperatures above 750 °C. This study presents an innovative approach to the fractal, multiscale texturing of absorber surfaces to significantly enhance solar energy absorption for Gen3 CSP applications. The absorber surface is described in terms of its fractal parameters that are uniquely determined from surface profile measurements. The interaction of solar radiation with the fractal surface is numerically simulated by solving the governing Maxwell’s equations for electromagnetic wave propagation to investigate the effect of texturing on the absorptance of the surfaces. It is shown that absorption of the solar spectrum increases with an increase in the fractal dimension and the multiscale asperity height of the surface texturing. Here, the theoretical model is demonstrated to be in close agreement with experimental measurements of spectral absorptance of electrodeposited copper (Cu), copper mono-oxide (CuO), and copper-manganese oxide (CuMnO) surfaces that are textured to produce a range of fractal parameters by tailoring the deposition parameters. Fractal surface texturing is shown to reduce reflectance by over one order of magnitude, yielding an absorptance of greater than 0.985 for CuMnO. For the first time, the study presents a significant effective means of increasing solar absorptance and a fundamental theoretical description of the underlying physics.

14 SOLAR ENERGY↗
DOE OSTI2020

Effect of salt concentration profiles on protrusion growth in lithium-polymer-lithium cells

In this report, the formation of dendrites and other protrusions on lithium metal anodes is a subject of continued interest due to the potential to incorporate these anodes in next-generation rechargeable batteries with increased energy densities. Solid polymer electrolytes show improved stability against lithium metal compared to liquid carbonate electrolytes. We have studied the effect of salt concentration on the formation of protrusions formed on electrodeposited lithium through a rigid block copolymer electrolyte, polystyrene-block-poly(ethylene oxide) (PS-b-PEO or SEO), in a lithium-lithium symmetric cell. The cell lifetime decreases by a factor of 100 when salt concentration is increased by a factor of 5. Our main objective is to understand the reason for this observation. We show that this decrease is not due to a salt-induced change of the morphology of the block-copolymer electrolyte, nor is it due to a salt-induced change of mechanical properties. We use an approach based on Newman's concentrated solution theory to fully characterize ion transport in the block-copolymer electrolyte, and report the conductivity, salt diffusion coefficient, cation transference number, and thermodynamic factor. Neither cell lifetime nor protrusion density in failed cells correlate with any of these electrochemical parameters. However, the electrochemical parameters can be used to predict salt concentration profiles in our symmetric cells. We posit that an important parameter in protrusion growth is the magnitude of the salt concentration gradient, Δ. We observe a direct correlation between Δ and lithium protrusion growth.

25 ENERGY STORAGE↗
DOE OSTI2020

Comparison of Orientation Mapping in SEM and TEM

In this work, multiple experimental configurations for performing nanoscale orientation mapping are compared to determine their fidelity to the true 3D microstructure of a sample. Transmission Kikuchi Diffraction (TKD) experiments in an SEM and nanobeam diffraction (NBD) experiments in a TEM were performed on thin electrodeposited hard Au films with two different microstructures. The Au samples either have a grain size that is >50 nm or <20 nm. The same regions of the samples were measured with TKD apparatuses at 30 kV in an SEM with detectors in the horizontal and vertical configurations and in the TEM at 300 kV. Under the proper conditions, we demonstrate all three configurations can produce data of equivalent quality.Each method has strengths and challenges associated with its application and representation of the true microstructure. The conditions needed to obtain high-quality data for each acquisition method and the challenges associated with each will be discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In Situ Synchrotron X-ray Scattering Investigation of Cathodic ZIF-8 Deposition on Graphite Using 3D-Printed Cells

Electrochemical approaches provide unique means to fabricate thin films of metal organic frameworks (MOFs). However, the kinetics of electrochemical MOF deposition has not been quantitatively investigated so far. In this study, we report the first in situ measurements of electrochemical MOF growth using transmission synchrotron X-ray scattering. Electrochemical cells based on poly(lactic acid) with two windows were fabricated using fused-deposition modelling. Here, the resulting 3D-printed cells, the surface of which was coated with paraffin wax to prevent solvent percolation through the polymer material, were used to monitor the cathodic growth of zeolitic imidazolate framework-8 (ZIF-8) on graphite in a methanol solution containing ZnCl 2 and 2-methylimidazole (Hmim) at different cathodic potentials. The resulting time-resolved X-ray diffraction data showed a gradual increase in crystal size with negligible changes in crystal orientation during the cathodic ZIF-8 deposition. More importantly, the time-resolved data provided a means to quantitatively assess the kinetics of the cathodic ZIF-8 growth using the Gualtieri model, revealing that the cathodic potential and Hmim concentration affected crystal growth kinetics, but not nucleation kinetics. These ZIF-8 samples exhibited changes in X-ray diffraction pattern after being washed with methanol and dried in air, indicating that in situ measurements are essential to investigate mechanisms behind MOF electrodeposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Diamonds in the Rough: Direct Surface Enhanced Infrared Spectroscopic Evidence of Nitrogen Reduction on Boron-Doped Diamond Supported Metal Catalysts

In situ investigations of electrocatalytic processes of increasing societal interest such as the nitrogen reduction reaction (NRR) re-quire aggressive experimental conditions that are not readily compatible with surface sensitive techniques such as attenuated total reflection surface enhanced infrared absorption spectroscopy (ATR-SEIRAS). A method for performing ATR-SEIRAS studies at very negative potentials where conventional IR-active films delaminate, and fail is reported. The method relies on a thin film of very robust boron-doped diamond deposited on a micromachined Si wafer, which provides extended mid-IR transparency at long wavelengths. SEIRAS activity is achieved by electrodepositing gold nanoparticles onto the conductive BDD layer. The Au@BDD layers are shown to sustain prolonged periods of electrolysis at negative potentials with no degradation of the modifying layer. The efficacy of these substrates for electrocatalysis is demonstrated by studying the reduction of N 2 at -1.5 V vs Ag/AgCl in an aqueous-based electrolyte. So under these conditions, direct spectroscopic evidence of both NH 3 and hydrazine formed from the nitrogen reduction reaction (NRR) is provided.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Combined Experimental and Theoretical Investigations of n-Type BiFeO 3 for Use as a Photoanode in a Photoelectrochemical Cell

Combined experimental and theoretical investigations were performed to evaluate the potential of n-type BiFeO 3 as a photoanode. While previous experimental and theoretical studies on BiFeO 3 mainly focused on its ferroelectric properties, several studies have reported the advantages of BiFeO 3 as a photoelectrode for solar water splitting (e.g. bandgap energy and band edge positions relative to water reduction and oxidation potentials). However, the photoelectrochemical properties of n-type BiFeO 3 have not yet been thoroughly investigated. In our experimental investigation, we developed an electrodeposition-based synthesis to prepare uniform n-type BiFeO 3 thin-film electrodes. Furthermore, using a heat treatment under a N 2 environment, we intentionally introduced additional oxygen vacancies into the pristine n-type BiFeO 3 electrodes to increase the majority carrier density. The bandgaps, flatband potentials, photocurrent onset potentials, photocurrent generation, and photoelectrochemical stabilities of the pristine and N 2 -treated BiFeO 3 photoanodes were investigated comparatively to improve our understanding of BiFeO 3 photoanodes and to examine the effect of oxygen vacancies on the photoelectrochemical properties of BiFeO 3 . In our theoretical investigation, we performed first-principles calculations and demonstrated the formation of a small polaron when an extra electron was introduced into the BiFeO 3 lattice. Changes in electronic states cause by the small polaron formation were carefully investigated. We also examined the effects of oxygen vacancies on electron polaron formation and carrier concentration in BiFeO 3 . Using charge formation energy calculations and referencing charge transition levels to the free electron polaron level instead of to the conduction band minimum, we showed that the oxygen vacancy is capable of serving as a donor to enhance the carrier concentration of BiFeO 3 . Furthermore, our theoretical results agree well with our experimental findings. Together, the new experimental and theoretical results and discussion provided in this study have considerably improved our understanding of n-type BiFeO 3 as a photoanode.

25 ENERGY STORAGE↗
DOE OSTI2023

Investigation of Electron Extraction and Protection Layers on Cu 2 O Photocathodes

Many semiconductor photoelectrodes used for solar fuel production require the addition of buffer and protection layers to enhance their solar-to-fuel conversion efficiency and long-term stability. For example, Cu 2 O, which is the most efficient oxide-based photocathode but suffers from photocorrosion, has been assembled with various buffer and protection layers to suppress photocorrosion and use more photoexcited electrons for useful reactions such as water reduction to H 2 . However, the abilities of various buffer and protection layers to extract electrons from Cu 2 O have never been directly evaluated. Instead, their abilities were estimated based on the photocurrent for water reduction after adding a hydrogen evolution catalyst on top of them. In these evaluations, as the photocurrent is affected not only by the buffer or protection layer but also by the catalyst, the ability of the buffer or protection layer to extract electrons from Cu 2 O could not be accurately determined or compared. Here, in this study, we demonstrate that 4-hydroxy-2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPOL), whose reduction rate is faster than the photocorrosion rate of Cu 2 O, can be used as an effective electron scavenger to directly evaluate any change caused by a buffer or protection layer in electron-hole separation in Cu 2 O. In particular, we compared the performances of ZnO and TiO 2 layers on Cu 2 O for extracting electrons and suppressing photocorrosion. We also compared the performances of TiO 2 layers prepared by electrodeposition and atomic layer deposition (ALD) to show that the deposition method can make a striking impact on the performance of the same TiO 2 because it can affect the critical characteristics of the layer (e.g., defect levels, conductivity, interfacial atomic arrangements) that govern interfacial charge transfer in multilayer photoelectrodes.

36 MATERIALS SCIENCE↗