Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Contact”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

INVESTIGATION OF ROCK-FLUID INTERACTIONS USING GEOMATERIAL MICROFLUIDICS

Illite and Illite-Smectite clays are reportedly the Caney Shale's most prevalent clay minerals. The swelling and fines migration of clays may occur when water-based fluids contact the clay minerals. This may result in the reduction of pore space and permeability, and wettability alteration. Therefore, we quantified the swelling potentials, fines migration and wettability alteration of Illite and Illite-Smectite clays upon exposure to model brines and a produced water, and a model oil and a crude oil. We measured density, viscosity, pH, TDS, and interfacial tension as they are important in multiphase flow and displacement characteristics. Geomaterial microfluidics is recently being used to study physicochemical interactions of solid-fluid systems. It facilitates visualizing the surface behavior upon exposure to various fluids. This study includes preparation and characterization of Illite-Smectite clay-coated glass capillary tubes. Illite and Illite-Smectite clay-coated geomaterial microfluidic surfaces were prepared to investigate the effects of first contact fluid, brine salinity, and aging on wettability. In this work, advancing and receding contact angles of model brine-air, model oil-air, produced water-air, crude oil-air, model brine-model oil systems, and produced water-crude oil systems have been measured in the untreated, and clay-coated microfluidic channels of 1000 µm width and 50 µm depth. The aging effect was studied by retaining the non-aqueous and aqueous solutions in the corresponding microfluidic channels for approximately 24 h in the case of channels first contacted by aqueous and non-aqueous solutions, respectively. The advancing and receding contact angles of Caney shale-crude oil-produced water systems were also measured. The experimental findings indicate the swelling potential, fines migration, and wettability alteration of Illite and Illite-Smectite clays. The results signify the influence of first contact fluid, brine salinity, and aging on wettability of the untreated and clay-coated microfluidic surfaces. The experiments also demonstrate the wetting nature of the Caney shale samples from reservoir and non-reservoir zones.

02 PETROLEUM↗
DOE OSTI2022

Atomistic insights into the heat conductance across the interfaces between erythritol and different metals: A non-equilibrium molecular dynamics study

The heat conductance across the interface between a phase change material (PCM) and the metal shell is important for thermal design of latent heat storage systems. Non-equilibrium molecular dynamics simulations were carried out in this work to unravel, at the atomistic level, the interfacial heat conductance mechanisms between erythritol (the most promising medium-temperature polyol PCM) and two different metals (i.e., copper and aluminum). The interfacial contact ratio was introduced as a parameter to represent different contact conditions at the interfaces, for example, different surface roughness levels of the metals. It was found that with the increase of interfacial contact ratio, the temperature difference between the erythritol/metal interfaces decreases, whereas the interfacial heat transfer coefficient increases gradually. At the perfect contact condition, i.e., the interfacial contact ratio reaches 100%, the interfacial heat transfer coefficients across the erythritol/Cu and erythritol/Al interfaces were predicted to be 398 ± 26 MW/m 2 K and 544 ± 11 MW/m 2 K, respectively. The interfacial heat conductance of erythritol/Al is better than that of erythritol/Cu. The mismatch of atomic spectral density across the interfaces between erythritol and the two metals was analyzed and distinguished. These results could guide the selection of packaging materials and the thermal design of erythritol-based latent heat storage systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Towards a predictive, physics-based friction model for the dynamics of jointed structures

Bolted connections are ubiquitous in mechanical designs and pose a significant challenge to understanding and predicting the vibration response of assembled structures. The present paper develops a physics-based rough contact model of the frictional interactions within a joint. This model sums over the probable interactions of asperities – defined as locally maximum surface features – to determine the contact forces. Here, the tangential contact forces vary smoothly between sticking and slipping and allow the model to better capture the qualitative trends of experimental amplitude dependent frequency and damping than previous studies. Furthermore, the novel model is generalized to allow for arbitrarily varying normal pressure including potential separation to better represent the interfacial dynamics. This includes developing a new, computationally tractable approximation to the analytical Mindlin partial slip solution for tangential loading of contacting spheres. Further, the results highlight the importance of accurately characterizing the as-built topology of the interface, the plastic behavior of the contacting asperities, the relevant length scale of asperities, and the eccentricity of asperities. A predictive friction coefficient based on plasticity provides a poor match to experiments, so fitting the friction coefficient is also considered. Numerical results are compared to experiments on the Brake-Reuß Beam to assess the predictive potential of the models. While blind predictions over-predict the slip limit, the current model presents a significant improvement in physics-based modeling and highlights areas for ongoing research.

42 ENGINEERING↗
DOE OSTI2021

Modulating Interactions between Molten Polystyrene and Porous Solids Using Atomic Layer Deposition

Understanding and modulating the interactions between molten polymers and porous solids is important for numerous processes and phenomena including catalytic conversion of polymers and fabrication of nanocomposites and nanostructured materials. Although changing the surface composition of pores would enable modulation of interactions between polymer and nanoporous solids, it is challenging to achieve such a control without inducing significant changes to the size and structure of nanopores. In this work, we demonstrate that the interactions between molten polystyrene (PS) and disordered packings of SiO 2 nanoparticles (NPs) can be modulated by changing the surface composition of the NPs using atomic layer deposition (ALD). A disordered packing of silica NPs is modified with varying surface coverages of TiO 2 , WO 3 and CaCO 3 , with coverages estimated by the mass gain and the refractive index change of NP packings. Based on the time required to fully infiltrate these ALD-modified NP packings via capillarity, the contact angles for PS on different surfaces prepared via ALD are determined. The contact angle gradually changes from that of pure SiO 2 to that of the fully covered surfaces. The contact angles for PS on SiO 2 , TiO 2 , WO 3 and CaCO 3 are found to be 20°, 62°, 70° and 10°, respectively. Interestingly, the contact angles and interfacial energies between PS and the ALD-modified surfaces do not correlate strongly with the water contact angle of these surfaces; thus, caution must be exercised in predicting how a polymer would wet or interact with porous solids solely based on their hydrophilicity. Furthermore, the method presented in this work can be extended to study the interactions between a wide range of polymers and surfaces in porous media, which will have important implications for designing new catalytic materials for polymer upcycling reactions as well as novel NP-polymer composite films and membranes with enhanced mechanical and transport properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Combined Stress Testing of Perovskite Solar Cells for Stable Operation in Space

Perovskite solar cells (PSCs) could provide new low-cost opportunities for powering spacecraft. Here we are designing a PSC resilient to lunar surface conditions, focusing on contact/barrier layers combinations that maximize stability. Thermal vacuum stress shows cells with gold back-contacts and SiOx protection retain >90% of initial efficiency and indium tin oxide (ITO)-contacted cells retain ~100% of initial efficiency after five months of stress. SiO x mitigates mechanical aspects of contact stress, retaining 99% of initial efficiency, whereas cells with silicone/cover glass decreased 27%. We further exposed cells to combined illumination, 75 °C heat, and 10 -6 Torr vacuum for 24 h and found that ITO-contacted cells outperformed Au-contacted cells.

14 SOLAR ENERGY↗
DOE OSTI2025

Selective Isolation of Surface Grain Boundaries by Oxide Dielectrics Improves Cd(Se,Te) Device Performance

Cd(Se,Te) photovoltaics (PV) are the most widely deployed thin-film solar technology globally, yet continued efficiency improvements are stymied by challenges at the device hole contacts. The inclusion of solution-processed oxide layers such as AlGaO x in the contact stack has yielded improved device open-circuit voltages (V OC ) and fill factors (FF). However, contradictory mechanisms by which these layers improve the device properties have been proposed by the research community. We demonstrate in this work that an underappreciated property of such spin-coated layers is the preferential deposition at grain boundaries, a process that isolates the grain boundaries during contact metallization. The effects of grain-boundary isolation are probed by varying the coverage of solution-processed AlGaO x “barrier” layers on the Cd(Se,Te) surface, quantified by scanning Auger microscopy. Examining coverage-dependent V OC and FF, it was observed that isolating the grain boundaries during metallization is sufficient to prevent damage to the absorber that occurs in devices lacking a barrier layer, while additional coverage contributes to the increased series resistance. Such an effect is agnostic to the material used as a barrier layer, as long as the material does not itself damage the absorber. Spin-coated SiO x was used in place of AlGaO x for an equally beneficial effect. This grain-boundary isolation phenomenon is also observed during Mo deposition and in absorbers that have been contacted with a nitrogen-doped ZnTe layer. The mechanisms by which metallization may degrade the absorber are discussed, as are contact design strategies leveraging barrier layers, which may lead to improved device efficiencies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Experimental analysis of conductive drying of paper and board

The primary heat transfer source in the conventional multi-cylinder drying of paper and board is conduction. Conduction is facilitated by high-tension contact with steam-heated cylinders, while convective drying, the main mass transfer source, operates as heated air flows over the paper web in the pockets. This conduction process occurs at elevated temperatures and contact pressures to ensure effective contact between the wet paper web and the heated cylinders. The contact pressures and temperatures of the hot surface significantly influence the conductive drying characteristics. This research paper presents an experimental study that involves designing a simple lab-scale setup with in-situ and continuous sensing capabilities for various commercially available grades of paper and board. Embedded thermocouples measure the temperatures of the heated platen and the sheet, allowing the collection of flux data to determine heat transfer characteristics. Here, the goal of this study is to ascertain the instantaneous contact coefficients for different basis weights as a function of moisture content. The acquired data will provide valuable insights and information towards process development, design and simulation of the paper drying process.

42 ENGINEERING↗
DOE OSTI2021

Stress- and Time-Dependent Formation of Self-Lubricating In Situ Carbon (SLIC) Films on Catalytically-Active Noble Alloys

Abstract Low shear strength (30 MPa) organic films were grown in situ on Pt 0.9 Au 0.1 surfaces via cyclic sliding contact in dry N 2 with trace concentrations of ambient hydrocarbons. We present a systematic investigation of the stress- and time-dependent film formation. Steady-state friction coefficients were found to be as low as µ ~ 0.015 and inversely proportional to contact pressure, revealing non-Amontonian behavior. Above a Hertzian contact pressure of ~500 MPa, shear strength dropped, indicating an activated process. Raman spectroscopy identified non-uniformity in areal coverage and relative order with contact pressure. Regions of steady-state low-friction behavior exhibited spectra similar to DLC coatings. Atomic force microscopy was used to study the formation and growth of films at the nanoscale. Stress- and time-dependent measurements suggested a sublinear increase of film volume with time, and a transition from growth to wear at a Hertzian contact pressure of ~1.2 GPa.

Jones, Morgan R.↗
DOE OSTI2024

Concurrent measurement of strain and chemical reaction rates in a calcite grain pack undergoing pressure solution: Evidence for surface-reaction controlled dissolution

Pressure solution is inferred to be a significant contributor to sediment compaction and lithification, especially in carbonate sediments. For a sediment deforming primarily by pressure solution, the compaction rate should be directly related to the rate of calcite dissolution, transport along grain contacts, and calcite reprecipitation. Previous experimental work has shown that there is evidence that deformation in wet calcite grain packs is consistent with control by pressure solution, but considerable ambiguity remains regarding the rate limiting mechanism. We present the results of laboratory compaction experiments designed to directly measure calcite dissolution and precipitation rates (recrystallization rates) concurrently with strain rate to test whether measured rates are consistent with predicted rates both in absolute magnitude and time evolution. Recrystallization rates are measured using trace element chemistry (Sr/Ca, Mg/Ca) and isotopes (87Sr/86Sr) of fluids flowing slowly through a compacting grain pack as it is being triaxially compressed. Imaging techniques are used to characterize the grain contacts and strain effects in the post-experiment grain pack. Our data show that calcite recrystallization rates calculated from all three geochemical parameters are in approximate agreement and that the rates closely track strain rate. The geochemically inferred rates are close to predicted rates in absolute magnitude. Uncertainty in grain contact dimensions makes distinguishing between surface reaction control and diffusion control difficult. Measured reaction rates decrease faster than predicted from standard pressure solution creep flow laws. This inconsistency may indicate that calcite dissolution rates at grain contacts are more complex, and more time-dependent, than suggested by geometric models designed to predict grain contact stresses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ion irradiation effects on Cr-coated zircaloy-4 surface wettability and pool boiling critical heat flux.

The concept of coating the currently used nuclear fuel cladding (zirconium-based alloy, typically Zircaloy-4 or Zirc-4) with an oxidation preventive layer is a progressing Accident tolerant Fuel (ATF) candidate alloys. The coated Zirc-4-based alloys could be a solution to suppress undesirable fast reaction kinetics with high-temperature steam. Zirc-4 has been the most preferred cladding material in pressurized water reactors (PWRs). Chromium (Cr) based alloys as a coating material provides excellent corrosion protection and good strength and wear resistance. In this paper, we present the surface wettability measurements and pool boiling Critical Heat Flux (CHF) for Cr-coated Zirc-4 claddings pre- and post-exposure to an ion irradiation environment. The wettability measurements, including static contact angle (contact angle, θ) and average surface roughness (surface roughness, Ra), are introduced for samples of different coating thicknesses (5–30 μm thick). The coatings fabricated by the cold spray of Cr-Al particles to 10 mm × 10 mm × 1.95 mm Zirc-4 substrates. Post fabrication, a Pilgering (cold rolling) process, was applied to finalize the coating thickness and resulted in a significant reduction in surface roughness of initially fabricated rough surfaces. The process produced three distinguished samples 5-μm unpolished (as machined), 5-μm, and 30-μm polished (cold rolled). The measurements are presented for the three surfaces and bare Zirc-4 as a baseline surface. The contact angle analyses were implemented in theoretical models from the literature to predict pool boiling CHF. Pool boiling experiments were conducted to measure the pool boiling CHF values and compare them to the predicted values. Scanning Electron Microscope (SEM) images and Energy Dispersive X-ray Spectroscopy (EDS) analysis was performed to characterize the surfaces for better understanding and interpreting the results. The SEM images showed localized surface damage due to ion irradiation. No recognized change in the measured surface roughness due to ion irradiation. The contact angles of irradiated Cr-coated surfaces are consistently higher (10°) than pre-irradiated surfaces. Decreasing the Cr-coating layer thickness resulted in lower contact angle pre- and post- ion irradiation. The predicted pool boiling CHF using the Kandlikar model is in good agreement with the experimentally measured CHF values within ±12% for all samples.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Buried Interfaces in Organic Photocathodes for H 2 Evolution: Fermi-Level Pinning and Recombination

Herein, we demonstrate how Fermi-level pinning at buried contacts impacts solar fuel generation in all-polymer photocathodes by systematically comparing the effects of work function, hydroxyl coverage, and hydrogen evolution using chemically modified indium tin oxide (ITO) supports. Photovoltages and net photocathode performance are improved when the ITO is passivated using phosphonic acids, independent of work function, suggesting that the passivation reduces Fermi-level pinning at the buried interface arising from blended heterojunction interactions with surface metal hydroxyls. Transient photovoltage decay reveals differences in recombination mechanisms, supported by light intensity-dependent measurements. Briefly, nonpassivated, hydrophilic contacts exhibit trap-assisted recombination, while passivated, hydrophobic contacts follow bimolecular recombination. We then investigate changes in electroactivity of hole-transfer processes as a function of scan rate and repetitive cycling using a diffusion-controlled molecular redox probe, analogous to a hole-only device achieved via the electrolyte. The nonpassivated buried contacts exhibit higher overpotentials for oxidation, indicative of hole injection/extraction barriers. We observe irreversible electron transfer via the hole-transport level of the blended heterojunction and a strong cycle dependence, consistent with changes in the hole trap state density. Passivation results in more reversible redox behaviors, consistent with more Ohmic-like contacts. Collectively, these results provide context toward the realization of durable organic photoelectrodes with optimized photovoltages and net solar-to-hydrogen conversion efficiencies via fundamental understanding of the rates of carrier generation, recombination, and transport in high-dielectric aqueous environments and opportunities to characterize buried interfaces under device-relevant electric fields.

buried interfaces↗
DOE OSTI2020

A particle finite element-based model for droplet spreading analysis

Here, a particle finite element method-based model is proposed to analyze droplet dynamics problems, particularly droplet spreading on solid substrates (wetting). The model uses an updated Lagrangian framework to formulate the governing equations of the liquid. The curvature of the liquid surface is tracked accurately using a deforming boundary mesh. In order to predict the spreading rate of the droplet on the solid substrate and track the corresponding contact angle evolution, dissipative forces at the contact line are included in the formulation in addition to the Navier-slip boundary conditions at the solid–liquid interface. The inclusion of these boundary conditions makes it possible to account for the induced Young’s stress at the contact line and for the viscous dissipation along the solid–liquid interfacial region. These are found to be essential to obtain a mesh-independent physical solution. The temporal evolution of the contact angle and the contact line velocity of the proposed model are compared with spreading droplets and micro-sessile droplet injection experiments and are shown to be in good agreement.

42 ENGINEERING↗
DOE OSTI2023

Evaluating the active site-substrate interplay between x-ray crystal structure and molecular dynamics in chorismate mutase

Designing realistic quantum mechanical (QM) models of enzymes is dependent on reliably discerning and modeling residues, solvents, and cofactors important in crafting the active site microenvironment. Interatomic van der Waals contacts have previously demonstrated usefulness toward designing QM-models, but their measured values (and subsequent residue importance rankings) are expected to be influenceable by subtle changes in protein structure. Using chorismate mutase as a case study, this work examines the differences in ligand-residue interatomic contacts between an x-ray crystal structure and structures from a molecular dynamics simulation. Select structures are further analyzed using symmetry adapted perturbation theory to compute ab initio ligand-residue interaction energies. The findings of this study show that ligand-residue interatomic contacts measured for an x-ray crystal structure are not predictive of active site contacts from a sampling of molecular dynamics frames. In addition, the variability in interatomic contacts among structures is not correlated with variability in interaction energies. However, the results spotlight using interaction energies to characterize and rank residue importance in future computational enzymology workflows.

Chemistry↗
DOE OSTI2024

Mesoscale simulation of granular materials under weak shock compaction–pore size distribution effects

This research established a systematic method to generate various pore-size distributions (PSDs) and studied the effect of PSDs on the shock compaction response of granular materials using two-dimensional mesoscale simulations under identical porosity. Simulations utilized various PSDs for three particle shapes (circle, ellipse, and square). Contacting particle configurations using three PSDs, characterized by spatially uniform distributed pores to heterogeneous distributed pores, and non-contacting particle configurations under a single case of PSD were tested. The PSD of generated particle sets was characterized using coordination number, mean diameter, and bimodality coefficient as statistical metrics. Mesoscale simulations showed that regardless of the conditions of pore distributions, shock compaction of granular materials consistently demonstrates a precursor, shock compaction front, and end. However, the shock compaction velocity of contacting particles was dependent on the PSDs despite the constant initial porosity. The compaction velocity was faster in particle configurations with relatively uniform pore distributions than in heterogeneous pore distributions, which our study demonstrated can be attributed to particle rearrangement during compaction. Circular-shaped particles had high sensitivity in shock compaction response to the various PSDs. Furthermore, a contacting particle configuration tended to propagate the shock compaction wave relatively faster than particles that were in a non-contact configuration. This study established the relative importance of considering PSD as a metric over the coordination number in studies of the shock compaction response of granular materials. Further, insights are provided on the evolving shock substructure to characterize the shock compaction response of granular materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Wettability and capillary effects: Dynamics of pinch-off in unconstricted straight capillary tubes

We study the interfacial evolution of immiscible two-phase flow within a capillary tube in the partial wetting regime using direct numerical simulation. We investigate the flow patterns resulting from the displacement of a more viscous fluid by a less viscous one under a wide range of wettability conditions. We find that beyond a wettability dependent critical capillary number, a uniform displacement by a less viscous fluid can transition into a growing finger that eventually breaks up into discrete blobs by a series of pinch-off events for both wetting and non-wetting contact angles. This study validates previous experimental observations of pinch-off for wetting contact angles and extends those to non-wetting contact angles. We find that the blob length increases with the capillary number. We observe that the time between consecutive pinch-off events decreases with the capillary number and is greater for more wetting conditions in the displaced phase. Here, we further show that the blob separation distance as a function of the difference between the inlet velocity and the contact line speed collapses into two monotonically decreasing curves for wetting and non-wetting contact angles. For the phase separation in the form of pinch-off, this work provides a quantitative study of the emerging length and time scales and their dependence on the wettability conditions, capillary effects, and viscous forces.

42 ENGINEERING↗
DOE OSTI2023

The soil pore structure encountered by roots affects plant‐derived carbon inputs and fate

Summary Plant roots are the main supplier of carbon (C) to the soil, the largest terrestrial C reservoir. Soil pore structure drives root growth, yet how it affects belowground C inputs remains a critical knowledge gap. By combining X‐ray computed tomography with 14 C plant labelling, we identified root–soil contact as a previously unrecognised influence on belowground plant C allocations and on the fate of plant‐derived C in the soil. Greater contact with the surrounding soil, when the growing root encounters a pore structure dominated by small (< 40 μm Ø) pores, results in strong rhizodeposition but in areas of high microbial activity. The root system of Rudbeckia hirta revealed high plasticity and thus maintained high root–soil contact. This led to greater C inputs across a wide range of soil pore structures. The root–soil contact Panicum virgatum , a promising bioenergy feedstock crop, was sensitive to the encountered structure. Pore structure built by a polyculture, for example, restored prairie, can be particularly effective in promoting lateral root growth and thus root–soil contact and associated C benefits. The findings suggest that the interaction of pore structure with roots is an important, previously unrecognised, stimulus of soil C gains.

Plant Sciences↗
DOE OSTI2020

Wettability Effects on Falling Film Flow and Heat Transfer Over Horizontal Tubes in Jet Flow Mode

The performance of a falling-film heat exchanger is strongly linked to the surface characteristics and the heat transfer processes that take place over the tubes. The primary aim of this numerical study is to characterize the influence of surface wettability on the film flow behavior and its associated surface heat transfer in the jet-flow mode. Volume of fluid (VOF) based simulations are carried out for horizontal tubes with different surface wettabilities. The wettability of the tube surfaces is represented using the Kistler's dynamic contact angle model. Surface wettability effects ranging from superhydrophilic to superhydrophobic are studied by varying the equilibrium contact angle from 2 deg to 175 deg. Two different liquid mass flow rates of 0.06 and 0.18 kg/m-s corresponding to the inline and staggered jet flow modes are studied. Results are presented in terms of the liquid film thickness, the contact areas between the different phases (solid–liquid and liquid–air), and the heat transfer coefficient or Nusselt number. The resistance imposed by the increasing contact angles inhibits the extent of the liquid spreading over the tube surface, and this, in turn, influences the liquid film thickness, and the wetted area of the tube surface. A significant decrement in the heat transfer rate from the tube surfaces was observed as the equilibrium contact angle increased from 2 deg to 175 deg. The local distributions of the Nusselt number over the tube surface are strongly influenced by the flow recirculation in the liquid bulk.

Engineering↗
DOE OSTI2021

Performance and reliability of β-Ga 2 O 3 Schottky barrier diodes at high temperature

Beta-gallium oxide (ß-Ga 2 O 3 ) is an ultrawide bandgap semiconductor that has potential for power electronic applications and devices operating at high temperatures. Particularly important for these applications are its 4.9 eV bandgap, facile electron doping, and the ability to grow ß-Ga 2 O 3 crystals from the melt. In this work, vertical ß-Ga 2 O 3 Schottky barrier diodes were fabricated using Pt Schottky and Ti-based Ohmic contacts and Au contact pads on unintentionally doped n-type, (2¯01)-oriented single crystal substrates. The diode’s temperature-dependent electrical properties up to 400°C were investigated, and the Pt/Ga 2 O 3 Schottky barrier height was determined to be close to 1.2 eV. The degradation of the contacts over multiple cycles up to 400°C was observed, resulting in a significant increase in series resistance of the diodes by 1000× at ambient temperature after they were cycled. According to electron microscopy measurements, this degradation is likely due in part to the migration and oxidation of Ti at the top surface of the Au contact pads. This degradation highlights the need for further research and development to ensure stable Ohmic and Schottky contacts to Ga 2 O 3 at temperatures above 400°C.

36 MATERIALS SCIENCE↗