Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONFIGURABLE APPLICATIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Liquid rocket actuators and operators

All the types of actuators and associated operators used in booster, upper stage, and spacecraft propulsion and reaction-control systems except for chemical-explosive actuators and turbine actuators are discussed. Discussion of static and dynamic seals, mechanical transmission of motion, and instrumentation is included to the extent that actuator or operator design is affected. Selection of the optimum actuator configuration is discussed for specific application which require a tradeoff study that considers all the relevant factors: available energy sources, load capacity, stroke, speed of response, leakage limitations, environmental conditions, chemical compatibility, storage life and conditions, size, weight, and cost. These factors are interrelated with overall control-system design evaluations that are beyond the scope of this monograph; however, literature references are cited for a detailed review of the general considerations. Perinent advanced-state-of-the-art design concepts are surveyed briefly.

Source record↗

Space shuttle/food system study

This document establishes the Functional, physical and performance interface requirements are studied between the space shuttle orbiter and the galley water system, the orbiter and the galley electrical system, and the orbiter and the galley structural system. Control of the configuration and design of the applicable interfacing items is intended to maintain compatibility between co-functioning and physically mating items and to assure those performance criteria that are dependent upon the interfacing items.

Source record↗

An experimental simulation study of four crosswind landing gear concepts

An experimental investigation was conducted in order to evaluate several crosswind landing-gear concepts which have a potential application to tricycle-gear-configured, short take-off and landing (STOL) aircraft landing at crab or heading angles up to 30 deg. In this investigation, the landing gears were installed on a dynamic model which had a scaled mass distribution and gear spacing but no aerodynamic similarities when compared with a typical STOL aircraft. The model was operated as a free body with radio-control steering and was launched onto a runway sloped laterally in order to provide a simulated crosswind side force. During the landing rollout, the gear forces and the model trajectory were measured and the various concepts were compared with each other. Within the test limitations, the landing gear system, in which the gears were alined by the pilot and locked in the direction of motion prior to touchdown, gave the smoothest runout behavior with the vehicle maintaining its crab angle throughout the landing runout.

Stubbs, S. M.↗

Transport of liquid state nitrogen through long length service lines during thermal/vacuum testing

Physical and analytical aspects associated with the transport are presented. Included is a definition of the problems and difficulties imposed by the servicing of a typical solid cryogen system, as well as a discussion of the transport requirements and of the rationale which governed their solution. A successful detailed transport configuration is defined, and the application of established mathematics to the design approach is demonstrated. The significance of head pressure, pressure drop, line friction, heat leak, Reynolds number, and the fundamental equilibrium demands of pressure and temperature were examined as they relate to the achievement of liquid state flow. Performance predictions were made for the transport system, and several analytical quantities are tabulated. These data are analyzed and compared with measured and calculated results obtained while actually servicing a solid cryogen system during thermal/vacuum testing.

Florio, F. A.↗

Arrow-wing supersonic cruise aircraft structural design concepts evaluation. Volume 3: Sections 12 through 14

The design of an economically viable supersonic cruise aircraft requires the lowest attainable structural-mass fraction commensurate with the selected near-term structural material technology. To achieve this goal of minimum structural-mass fraction, various combinations of promising wing and fuselage primary structure were analyzed for the load-temperature environment applicable to the arrow wing configuration. This analysis was conducted in accordance with the design criteria specified and included extensive use of computer-aided analytical methods to screen the candidate concepts and select the most promising concepts for the in-depth structural analysis.

Sakata, I. F.↗

Aeromaneuvering Orbit Transfer Vehicles for the space transport system

Alternatives to all-propulsive manned Orbit Transfer Vehicles (OTV) are presented that utilize aeromaneuvering in combination with propulsive maneuvering. A summary of the results of feasibility and concept definition studies is induced along with a discussion of the advantages and disadvantages of aeromaneuvering as compared with all-propulsive vehicles. Manned aeromaneuvering OTV concepts are described, including the Aeromaneuvering Orbit-to-Orbit Shuttle (AMOOS) for future orbital transportation and the Aeromaneuvering Recovery System (AMRS) for emergency recovery of crewmen from high-altitude orbits. Data are provided regarding aeromaneuvering OTV configurations, performance, systems, tradeoffs, mission applications, and major design parameters, such as dynamic pressure, heating rates, and guidance.

Hethcoat, J. P.↗

The significance of wing end configuration in airfoil design for civil aviation aircraft

Lift-dependent induced drag in commercial aviation aircraft is discussed, with emphasis on the necessary compromises between wing and configuration modifications which better lift performance and the weight gains accompanying such modifications. Triangular, rectangular and elliptical configurations for wing ends are considered; attention is also given to airfoil designs incorporating winglets. Water tunnel tests of several configurations are reported. In addition, applications of wing and modifications to advanced technology commercial aviation aircraft and the Airbus A-300 are mentioned.

Zimmer, H.↗

Space Platform advanced technology study

The development of mechanical systems for space platforms which have universal application regardless of what platform configuration is built is discussed. The design requirements and fabrication of the orbiter berthing systems, berthing latch interface, berthing umbilical interface, and adaptive end effector are described.

Burns, G. C.↗

Hypersonic airbreathing missile concepts under study at NASA Langley Research Center

The design and performance of several tactical and strategic hypersonic airbreathing missile concepts under study at the NASA Langley Research Center are discussed from an evolutionary perspective. A mid- and chin inlet missile design, constrained to the Navy's vertical box launcher, was investigated; a performance comparison is presented that is favorable to the mid-inlet approach. Parasol wing, confined flow field, and spatula-like cruise missile configurations were examined with strategic applications in mind. The preliminary results are encouraging with respect to aerodynamic and volumetric efficiency and choice of engine integration schemes.

Hunt, J. L.↗

Permanent-Magnet Motors and Generators for Aircraft

Electric motors and generators that use permarotating machinery, but aspects of control and power conditioning are also considered. The discussion is structured around three basic areas: rotating machine design considerations presents various configuration and material options, generator applications provides insight into utilization areas and shows actual hardware and test results, and motor applications provides the same type of information for drive systems.

Echolds, E. F.↗

Analysis of flexible aircraft longitudinal dynamics and handling qualities. Volume 2: Data

Two analysis methods are applied to a family of flexible aircraft in order to investigate how and when structural (especially dynamic aeroelastic) effects affect the dynamic characteristics of aircraft. The first type of analysis is an open loop modal analysis technique. This method considers the effect of modal residue magnitudes on determining vehicle handling qualities. The second method is a pilot in the loop analysis procedure that considers several closed loop system characteristics. Both analyses indicated that dynamic aeroelastic effects caused a degradation in vehicle tracking performance, based on the evaluation of some simulation results. Volume 2 consists of the presentation of the state variable models of the flexible aircraft configurations used in the analysis applications mode shape plots for the structural modes, numerical results from the modal analysis frequency response plots from the pilot in the loop analysis and a listing of the modal analysis computer program.

Waszak, M. R.↗

New outlook on control of crystalline and chemical perfection during growth of silicon

Significant progress has been made in our understanding of the Czochralski crystal growth process with the realization that the incorporation of oxygen into silicon is directly related to the internal gettering capability of wafers during device fabrication. It was also recognized that the electronic properties exhibited by silicon during various stages of device fabrication were significantly affected by the thermal history of the silicon during the post-growth cool-down period. Turbulent melt convection, induced by unavoidable destabilizing thermal gradients, was found to interfere with homogeneous dopant (and oxygen) incorporation and to influence markedly the dynamics of nonequilibrium point defects in the solidified silicon matrix during the cool-down period. In view of the unavoidability of destabilizing thermal gradients in conventional crystal growth configurations, melt stabilization through the application of magnetic fields is generally considered a viable approach. Control of heat input to the melt through heat pipe systems, as used during growth of germanium, cannot be applied to industrial growth of silicon. Recent studies have shown that heat exchange systems located coaxially about a growing crystal can be used to stabilize and control not only heat transfer in the grown crystal, but also in the melt adjacent to the solidification interface.

Witt, A. F.↗

Elliptic generation of composite three-dimensional grids about realistic aircraft

An elliptic method for generating composite grids about realistic aircraft is presented. A body-conforming grid is first generated about the entire aircraft by the solution of Poisson's differential equation. This grid has relatively coarse spacing, and it covers the entire physical domain. At boundary surfaces, cell size is controlled and cell skewness is nearly eliminated by inhomogeneous terms, which are found automatically by the program. Certain regions of the grid in which high gradients are expected, and which map into rectangular solids in the computational domain, are then designated for zonal refinement. Spacing in the zonal grids is reduced by adding points with a simple, algebraic scheme. Details of the grid generation method are presented along with results of the present application, a wing-body configuration based on the F-16 fighter aircraft.

Sorenson, R. L.↗

Potential benefits of magnetic suspension and balance systems

The potential of Magnetic Suspension and Balance Systems (MSBS) to improve conventional wind tunnel testing techniques is discussed. Topics include: elimination of model geometry distortion and support interference to improve the measurement accuracy of aerodynamic coefficients; removal of testing restrictions due to supports; improved dynamic stability data; and stores separation testing. Substantial increases in wind tunnel productivity are anticipated due to the coalescence of these improvements. Specific improvements in testing methods for missiles, helicopters, fighter aircraft, twin fuselage transports and bombers, state separation, water tunnels, and automobiles are also forecast. In a more speculative vein, new wind tunnel test techniques are envisioned as a result of applying MSBS, including free-flight computer trajectories in the test section, pilot-in-the-loop and designer-in-the-loop testing, shipboard missile launch simulation, and optimization of hybrid hypersonic configurations. Also addressed are potential applications of MSBS to such diverse technologies as medical research and practice, industrial robotics, space weaponry, and ore processing in space.

Lawing, Pierce L.↗

Fabrication of prepackaged superalloy honeycomb Thermal Protection System (TPS) panels

High temperature materials were surveyed, and Inconel 617 and titanium were selected for application to a honeycomb TPS configuration designed to withstand 2000 F. The configuration was analyzed both thermally and structurally. Component and full-sized panels were fabricated and tested to obtain data for comparison with analysis. Results verified the panel design. Twenty five panels were delivered to NASA Langley Research Center for additional evaluation.

Blair, W.↗

Development of a coupled expert system for the spacecraft attitude control problem

A majority of the current expert systems focus on the symbolic-oriented logic and inference mechanisms of artificial intelligence (AI). Common rule-based systems employ empirical associations and are not well suited to deal with problems often arising in engineering. Described is a prototype expert system which combines both symbolic and numeric computing. The expert system's configuration is presented and its application to a spacecraft attitude control problem is discussed.

Kawamura, K.↗

The design of a joined wing flight demonstrator aircraft

A joined-wing flight demonstrator aircraft has been developed at the NASA Ames Research Center in collaboration with ACA Industries. The aircraft is designed to utilize the fuselage, engines, and undercarriage of the existing NASA AD-1 flight demonstrator aircraft. The design objectives, methods, constraints, and the resulting aircraft design, called the JW-1, are presented. A wind-tunnel model of the JW-1 was tested in the NASA Ames 12-foot wind tunnel. The test results indicate that the JW-1 has satisfactory flying qualities for a flight demonstrator aircraft. Good agreement of test results with design predictions confirmed the validity of the design methods used for application to joined-wing configurations.

Smith, S. C.↗

ISIS and META projects

ISIS and META are two distributed systems projects at Cornell University. The ISIS project, has developed a new methodology, virtual synchrony, for writing robust distributed software. This approach is directly supported by the ISIS Toolkit, a programming system that is distributed to over 300 academic and industrial sites. Several interesting applications that exploit the strengths of ISIS, including an NFS-compatible replicated file system, are being developed. The META project, is about distributed control in a soft real time environment incorporating feedback. This domain encompasses examples as diverse as monitoring inventory and consumption on a factory floor and performing load-balancing on a distributed computing system. One of the first uses of META is for distributed application management: the tasks of configuring a distributed program, dynamically adapting to failures, and monitoring its performance. Recent progress and current plans are presented. This approach to distributed computing, a philosophy that is believed to significantly distinguish the work from that of others in the field, is explained.

Birman, Kenneth↗