Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Breakup”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Total-sky and clear-sky variability of outgoing longwave radiation and shortwave radiation and its relation to cloud fluctuation statistics

Correlation statistics are used to investigate some of the characteristic temporal and spatial scales of the day-to-day changes in cloudiness which tend to dominate the variance of outgoing LW radiation and SW radiation fields. The temporal decorrelation time of the radiation field as measured by the lag time required for the autocorrelation of a region to fall to 0.4 is about 12 hours in the midlatitude storm track. Decorrelation time approaches one to two days when the averaging area of the region is increased significantly. Decorrelation times are also longer in the equatorial and tropical regions. The short decorrelation times are a manifestation of the creation, breakup, and movement of cloud systems. Cross-correlation analysis of the radiation field in the midlatitude storm track region and the subtropical dry zone shows advection speeds that range from about 25 m/sec in the storm tracks to about 8 m/sec in the subtropical dry zone.

Bess, T. D.↗

Dynamic behavior of liquid sheets

An experiment was conducted to study the aerodynamic instability of liquid sheets issuing from a two-dimensional air-assisted nozzle. Detailed measurements of the frequency of oscillation of the liquid sheet have been made. The measured vibrational frequencies were then correlated with the resulting spray angle. It was shown that the liquid sheet oscillations are dynamically similar to that of hard spring systems. For each air pressure, three distinct modes of breakup are distinguished. At low liquid flow rates, both the sinusoidal and the dilational modes are superimposed on the liquid sheet. With a further increase in liquid flow rate, the liquid sheet oscillations mainly become of the dilational type. It was also shown that the effect of introducing air in the nozzle is similar to the effect of inducing forced vibrations on the nozzle jaws. Thus, for each air flow rate, there is a specific vibration frequency for the nozzle. The frequency of these vibrations is proportional to the air velocity. As the liquid sheet natural frequency approaches that of the nozzle, resonance is established. At resonance, the maximum spray angle is achieved.

Mansour, Adel↗

Management of the orbital environment

Data regarding orbital debris are presented to shed light on the requirements of environmental management in space, and strategies are given for active intervention and operational strategies. Debris are generated by inadvertent explosions of upper stages, intentional military explosions, and collisional breakups. Design and operation practices are set forth for minimizing debris generation and removing useless debris from orbit in the low-earth and geosynchronous orbits. Self-disposal options include propulsive maneuvers, drag-augmentation devices, and tether systems, and the drag devices are described as simple and passive. Active retrieval and disposition are considered, and the difficulty is examined of removing small debris. Active intervention techniques are required since pollution prevention is more effective than remediation for the problems of both earth and space.

Loftus, Joseph P., Jr.↗

Cratering of the Uranian satellites

Available crater counts and their interpretations are reviewed, with emphasis on essential scaling considerations and comparisons with hypotheses developed for interpreting the cratering records on other planets and satellites. New approaches are employed to scaling based on new measurements of crater depths and morphology, which show craters in ice to be unexpectedly different from those in rock. It is found that the published crater counts on the Uranian satellites, despite mutual inconsistencies, can be interpreted as compatible with cratering by the heliocentric population of cometary bodies that was responsible for much of the cratering of the satellites of Jupiter and Saturn. Scaling arguments are applied to the catastrophic breakup of icy satellites and ring particles. The importance of large-scale collisions in disrupting the inner Uranian satellites is found to depend on the shape of the size distribution of cometary bodies at large sizes.

Mckinnon, William B.↗

Development of an improved model for runback water on aircraft surfaces

A computer simulation for 'running wet' and evaporative aircraft anti-icing systems is developed. The model is based on the analysis of the liquid water film which forms in the regions of direct impingement and, then, breaks up near the impingement limits into rivulets. The wetness factor distribution resulting from the film breakup and the rivulet configuration on the surface are predicted using a stability analysis theory and the laws of mass energy conservation. The solid structure is modeled as a multiple layer wall. The anti-icing system modeled is of the thermal type utilizing hot air and/or electrical heating elements embedded within the wall layers. Experimental observations revealing some of the basic physics of the water flow on the surface are presented. Detailed qualitative documentation of the tests are given. Several numerical examples are considered, and the effect of some of the involved parameters on the system performance are investigated.

Al-Khalil, Kamel M.↗

Space Cryogenics Workshop, 10th, Cleveland, OH, June 18-20, 1991, Proceedings

The present workshop on cryogenics discusses the anomalous on-orbit behavior of the Cosmic Background Explorer Dewar, the SHOOT orbital operations, cooling options for Astromag, and space IR telescope facility mission and cryogenic design. Attention is given to the design of a spaceworthy adiabatic demagnetization refrigerator, the evaluation of metal hydride compressors for applications in Joule-Thomson cryocoolers, diaphragm Stirling cryocooler developments, and a computer simulation model for Stirling refrigerators. Topics addressed include low-gravity thermal stratification of liquid helium on SHOOT, a screening program to select a resin for gravity probe-B composites, a simplified generic cryostat thermal model for predicting cryogen mass and lifetime, and the effect of gas mass flux on cryogenic liquid jet breakup. Also discussed are damping criteria for thermal acoustic oscillations in slush and liquid hydrogen systems, an STS-based cryogenic fluid management experiment, and the design and testing of a cryogenic mixer pump.

Source record↗

Numerical studies of dilute and dense spray characteristics

Several issues involving the improvement of physical submodels and the computational efficiency in modeling dilute and dense spray combustion are discussed. First, the implementations of a dispersion width approach accounting for turbulent dispersion within each computational parcel is discussed. This is essentially a statistical transport model and the testings of this model confirm the capability of accurately representing dispersion in nearly-homogeneous and inhomogeneous turbulent flows with improved efficiency over the delta function stochastic separated flow model. To account for the dense spray effects, an existing drop collision and coalescence model and a Taylor analogy breakup (TAB) model were employed. These models were incorporated into a state-of-the-art multiphase all-speed transient flow solution procedure. Several examples including nonevaporating, evaporating, and burning dense spray cases were studied. The numerical results show reasonably good comparisons with available experimental data in terms of spray penetration, drop sizes, and overall configuration of a spray flame.

Kim, Y. M.↗

Defining the background status of a debris cloud

When a satellite fragments, a debris cloud is produced which continues to orbit the earth in its place. The fragments do not remain in the same orbit as their parent, however, and the shape of this cloud begins to evolve. Over the course of several years, the cloud changes from an ellipsoid, to a pinched torus in the parent orbital plane, to a full torus in the equatorial plane, after which time it is considered to be part of the background environment. The elapsed time between breakup and background is called the time-to-background (TTB) and is calculated differently by different researchers. This report reviews existing methods employed by programs DEBRIS and SCREEN for determining the TTB, and offers two others for consideration for a community-wide standard. It is concluded that while each method has its merits, the debris community should agree on a specific computational definition for TTB that could be used as an industry-wide standard for comparing results.

Maclay, Timothy D.↗

A numerical model for coupling between atomization and spray dynamics in liquid rocket thrust chambers

This paper describes a novel method of coupling the atomization and spray combustion processes encountered in coaxial injection elements of liquid rocket engine thrust chambers. This method is based on the Jet-Embedding technique in which the liquid jet core equations and the gas phase equations are solved separately. The liquid and gas phase solutions, however, are coupled through the boundary conditions at the interface between the phases. The computational grid for the gas phase calculations are adapted to the shape of the liquid jet core. The axial variation of droplet sizes are calculated using a stability analysis appropriate for the atomization regime of liquid jet breakup. The predictions of this method have been validated with experimental data on low speed water jets. Using this method, calculations are performed for the SSME fuel preburner single injector flow field. The results obtained are in good agreement with the predictions of the volume-of-fluid method.

Giridharan, M. G.↗

The flux of small asteroids near the Earth

Fifteen new EA's (Earth approachers) have been discovered since September, among them the smallest asteroids on record: 1990 UN, 1991 BA, and 1991 JR, which are in the 10 to 100 m size range (Scotti et al. 1991b). For the first time, we can make estimates of the fluxes near the Earth of these small objects, thought to be the immediate parents of meteorites, from direct observation. In this paper, I show that for EA's larger than a few 100 m, the magnitude-frequency dependence we observe is consistent with the cumulative magnitude-frequency relation, m(H), established for the main belt asteroids. Assuming this relation extends to smaller sizes, however, the probability for discovering both 1990 UN and 1991 JR was 15 percent, and for discovering 1991 BA only 1 percent. Objects smaller than approx. 100 m are therefore increasingly overabundant compared to an extrapolation from larger objects, with the excess increasing with decreasing size. Near 10 m, the most probable flux near the Earth is two orders of magnitude higher. This is in agreement with the flux extrapolated from observations of bright meteors and fireballs. It is thus likely that processes other than collisional breakup of asteroidal material begin to supply the population of small objects near the Earth at sizes near 100 m. Tantalizing clues from spectral measurements and orbital associations suggest that these objects may be the debris from extinct, short-period comets.

Rabinowitz, David L.↗

Atomizing-gas temperature effect on cryogenic spray dropsize

Correlating expressions for two-phase flow breakup of liquid nitrogen, LN2, jets in sonic velocity nitrogen gasflows were obtained for an atomizing-gas temperature range of 111 to 442 K. The correlations were based on characteristic dropsize measurements obtained with a scattered-light scanner. The effect of droplet vaporization on the measurements of the volume-median dropsize was calculated by using previously determined heat and momentum transfer expressions for droplets evaporating in high-velocity gasflow. Finally, the dropsize of the originally unvaporized spray was calculated, normalized with respect to jet diameter and correlated with atomizing-gas flowrate and temperature.

Ingebo, Robert D.↗

Description of alpha-nucleus interaction cross sections for cosmic ray shielding studies

Nuclear interactions of high-energy alpha particles with target nuclei important for cosmic ray studies are discussed. Models for elastic, quasi-elastic, and breakup reactions are presented and compared with experimental data. Energy-dependent interaction cross sections and secondary spectra are presented based on theoretical models and the limited experimental data base.

Cucinotta, Francis A.↗

Comparisons of cross-section predictions for relativistic iron and argon beams with semiempirical fragmentation models

Cross-section predictions with semi-empirical nuclear fragmentation models from the Langley Research Center and the Naval Research Laboratory are compared with experimental data for the breakup of relativistic iron and argon projectile nuclei in various targets. Both these models are commonly used to provide fragmentation cross-section inputs into galactic cosmic ray transport codes for shielding and exposure analyses. Overall, the Langley model appears to yield better agreement with the experimental data.

Townsend, Lawrence W.↗

SPECS: Orbital debris removal

The debris problem has reached a stage at which the risk to satellites and spacecraft has become substantial in low Earth orbit (LEO). This research discovered that small particles posed little threat to spacecraft because shielding can effectively prevent these particles from damaging the spacecraft. The research also showed that, even though collision with a large piece of debris could destroy the spacecraft, the large pieces of debris pose little danger because they can be tracked and the spacecraft can be maneuvered away from these pieces. Additionally, there are many current designs to capture and remove large debris particles from the space environment. From this analysis, it was decided to concentrate on the removal of medium-sized orbital debris, that is, those pieces ranging from 1 cm to 50 cm in size. The current design incorporates a transfer vehicle and a netting vehicle to capture the medium-sized debris. The system is based near an operational space station located at 28.5 deg inclination and 400 km altitude. The system uses ground-based tracking to determine the location of a satellite breakup or debris cloud. These data are uploaded to the transfer vehicle, which proceeds to rendezvous with the debris at a lower altitude parking orbit. Next, the netting vehicle is deployed, tracks the targeted debris, and captures it. After expending the available nets, the netting vehicle returns to the transfer vehicle for a new netting module and continues to capture more debris in the target area. Once all the netting modules are expended, the transfer vehicle returns to the space station's orbit where it is resupplied with new netting modules from a space shuttle load. The new modules are launched by the shuttle from the ground and the expended modules are taken back to Earth for removal of the captured debris, refueling, and repacking of the nets. Once the netting modules are refurbished, they are taken back into orbit for reuse. In a typical mission, the system has the ability to capture 50 pieces of orbital debris. One mission will take approximately six months and the system is designed to allow for a 30 deg inclination change on the outgoing and incoming trips of the transfer vehicle.

Source record↗

Atomization characteristics of impinging liquid jets

A systematic study is presented of the atomization of impinging liquid jets investigating the effects of jet conditions (laminar versus turbulent), orifice diameter, impingement angle and jet velocity. Results are compared to current theories in terms of sheet breakup length, sheet shape and drop size. Experiments contrasting laminar and turbulent jet conditions clearly show that the jet conditions have a dramatic effect on the atomization process.

Ryan, H. M.↗

Absolute and convective instability of a viscous liquid jet surrounded by a viscous gas in a vertical pipe

The absolute and convective instability of a viscous liquid jet emanating into a viscous gas in a vertical pipe is analyzed in a parameter space spanned by the Reynolds number, the Froude number, the Weber number, the viscosity ratio, the density ratio, and the diameter ratio. The numerical results of the analysis are used to demonstrate that reduction in gravity tends to enhance the Rayleigh mode of convective instability which leads to the breakup of a liquid jet into drops of diameters comparable with the jet diameter. On the contrary, the Taylor mode of convective instability that leads to atomization is retarded at reduced gravity. The Rayleigh mode becomes absolutely unstable when the Reynolds number exceeds a critical value for a given set of the rest of the relevant parameters. The domain of absolute instability is significantly enlarged when the effect of gas viscosity is not neglected.

Lin, S. P.↗

VLF wave growth from dispersive bursts of field-aligned electron fluxes

Large-amplitude electrostatic whistler waves near the lower hybrid frequency were observed by an auroral sounding rocket during substorm breakup. The measured wavelengths indicate that the emissions were electrostatic and resonant with electrons that had parallel energies of a few hundred electron volts. We propose that the intense emissions drew their energy from dispersive bursts of low-energy, field-aligned electron fluxes. The dispersive bursts are known to cause a brief, but intense instability that results in large-amplitude Langmuir emissions. The high-frequency emissions can rapidly form a plateau in the one-dimensional electron distribution. We show, however, that these distributions remain unstable to electrostatic whistler waves near the lower hybrid frequency. The amplitude and wavelength of the observed emissions were sufficient to accelerate the hydrogen ions with energies between about 50 eV and about 200 eV.

Ergun, R. E.↗

The rollup of a vortex layer near a wall

The behavior of an inviscid vortex layer of non-zero thickness near a wall is studied, both through direct numerical simulation of the two-dimensional vorticity equation at high Reynolds numbers, and using an approximate ordinary nonlinear integro-differential equation which is satisfied in the limit of a thin layer under long-wavelength perturbations. For appropriate initial conditions the layer rolls up and breaks into compact vortices which move along the wall at constant speed. Because of the effect of the wall, they correspond to equilibrium counter-rotating vortex dipoles. This breakup can be related to the disintegration of the initial conditions of the approximate nonlinear dispersive equation into solitary waves. The study is motivated by the formation of longitudinal vortices from vortex sheets in the wall region of a turbulent channel.

Jimenez, Javier↗