Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Analytical Method Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Photogrammetry Methodology Development for Gossamer Spacecraft Structures

Photogrammetry--the science of calculating 3D object coordinates from images--is a flexible and robust approach for measuring the static and dynamic characteristics of future ultra-lightweight and inflatable space structures (a.k.a., Gossamer structures), such as large membrane reflectors, solar sails, and thin-film solar arrays. Shape and dynamic measurements are required to validate new structural modeling techniques and corresponding analytical models for these unconventional systems. This paper summarizes experiences at NASA Langley Research Center over the past three years to develop or adapt photogrammetry methods for the specific problem of measuring Gossamer space structures. Turnkey industrial photogrammetry systems were not considered a cost-effective choice for this basic research effort because of their high purchase and maintenance costs. Instead, this research uses mainly off-the-shelf digital-camera and software technologies that are affordable to most organizations and provide acceptable accuracy.

Pappa, Richard S.↗

Photogrammetry Methodology Development for Gossamer Spacecraft Structures

Photogrammetry--the science of calculating 3D object coordinates from images-is a flexible and robust approach for measuring the static and dynamic characteristics of future ultralightweight and inflatable space structures (a.k.a., Gossamer structures), such as large membrane reflectors, solar sails, and thin-film solar arrays. Shape and dynamic measurements are required to validate new structural modeling techniques and corresponding analytical models for these unconventional systems. This paper summarizes experiences at NASA Langley Research Center over the past three years to develop or adapt photogrammetry methods for the specific problem of measuring Gossamer space structures. Turnkey industrial photogrammetry systems were not considered a cost-effective choice for this basic research effort because of their high purchase and maintenance costs. Instead, this research uses mainly off-the-shelf digital-camera and software technologies that are affordable to most organizations and provide acceptable accuracy.

Pappa, Richard S.↗

Hydrocarbon Cold-Flow Simulation of LOX/LH2 Rocket Aerodynamics

In FY19, this project developed a test method which employed heated ethane in the physical simulation of rocket plume aerodynamics. Based on this work, EUS partnered with significant leveraged funding. A portable, self-contained test bed was also fabricated to support validation of the new method. In FY20, this project focused on the formal validation of ethane’s performance as an aerodynamic simulant as well as the development of the analytical and hardware infrastructure required to carry out that task. The test bed was activated, a series of heated-ethane tests on one or more rocket/diffuser configurations were conducted, and characterizations of the performance of the ethane simulation compared to hot-fire were performed. A series of 127 tests were conducted on 13 aerodynamic configurations to evaluate ethane’s performance as a simulant. It was found that the new methodology can reproduce rocket plume flow fields with +/- 0.5% pressure error at ~3% physical scale. The result is a cost-per-test reduction of ~99% compared to the hot-fire subscale testing typically used to obtain equivalent data. Some initial efforts have taken place, and future efforts are being planned with LaRC supersonic retro propulsion and MSFC SLS aerodynamics teams, which are interested in using the ethane system to wind-tunnel test human-rated Mars lander retrorockets and SLS Booster. Details of the prototypical experiments were published as NASA TM 2020-5009122,and have been presented in JANNAF Virtual Conference paper, "New Developments in Retro propulsion Testing for Mars Entry, Descent and Landing".

Daniel Jones↗

Optimal cooperative time-fixed impulsive rendezvous

A method has been developed for determining optimal, i.e., minimum fuel, trajectories for the fixed-time cooperative rendezvous of two spacecraft. The method presently assumes that the vehicles perform a total of three impulsive maneuvers with each vehicle being active, that is, making at least one maneuver. The cost of a feasible 'reference' trajectory is improved by an optimizer which uses an analytical gradient developed using primer vector theory and a new solution for the optimal terminal (rendezvous) maneuver. Results are presented for a large number of cases in which the initial orbits of both vehicles are circular but in which the initial positions of the vehicles and the allotted time for rendezvous are varied. In general, the cost of the cooperative rendezvous is less than that of rendezvous with one vehicle passive. Further improvement in cost may be obtained in the future when additional, i.e., midcourse, impulses are allowed and inserted as indicated for some cases by the primer vector histories which are generated by the program.

Mirfakhraie, Koorosh↗

Pterodactyl: Trade Study for an Integrated Control System Design of a Mechanically Deployable Entry Vehicle

This paper presents the trade study method used to evaluate and downselect from a set of guidance and control (G&C) system designs for a mechanically Deployable Entry Vehicle (DEV). The Pterodactyl project was prompted by the challenge to develop an effective G&C system for a vehicle without a backshell, which is the case for DEVs. For the DEV, the project assumed a specific aeroshell geometry pertaining to an Adaptable, Deployable Entry and Placement Technology (ADEPT) vehicle, which was successfully developed by NASA’s Space Technology Mission Directorate (STMD) prior to this study. The Pterodactyl project designed three different entry G&C systems for precision targeting. This paper details the Figures of Merit (FOMs) and metrics used during the course of the project’s G&C system assessment. The relative importance of the FOMs was determined from the Analytic Hierarchy Process (AHP), which was used to develop weights that were combined with quantitative design metrics and engineering judgement to rank the G&C systems against one another. This systematic method takes into consideration the project’s input while simultaneously reducing unintentional judgement bias and ultimately was used to select a single G&C design for the project to pursue in the next design phase.

Alunni, Antonella I.↗

A new method for determining acoustic-liner admittance in a rectangular duct with grazing flow from experimental data

A method is developed for determining acoustic liner admittance in a rectangular duct with grazing flow. The axial propagation constant, cross mode order, and mean flow profile is measured. These measured data are then input into an analytical program which determines the unknown admittance value. The analytical program is based upon a finite element discretization of the acoustic field and a reposing of the unknown admittance value as a linear eigenvalue problem on the admittance value. Gaussian elimination is employed to solve this eigenvalue problem. The method used is extendable to grazing flows with boundary layers in both transverse directions of an impedance tube (or duct). Predicted admittance values are compared both with exact values that can be obtained for uniform mean flow profiles and with those from a Runge Kutta integration technique for cases involving a one dimensional boundary layer.

Watson, W. R.↗

Developing a Pyrolysis Gas Thermal Blocking Model for Reentry Demise

In NASA’s Object Reentry Survival Analysis Tool (ORSAT), aerodynamic drag and aerothermal heating coefficients are computed for each of the free-molecular, continuum, and transitional flow regimes using analytical and semi-analytical methods. These heating coefficients were derived for typical metallic materials that melt and do not have a strong gas-phase contribution to the flow in the boundary layer. Modern satellites typically feature fiber-reinforced polymer (FRP) components, such as solar array booms, facesheets of sandwich panels, or overwraps for composite-overwrapped pressure vessels (COPV). These FRP materials do not behave the same as metals in the reentry environment, but instead will pyrolyze and develop significant volumes of gas into the boundary layer. Accurately predicting the reentry demise of FRP components is critical to assessing the reentry casualty risk for modern spacecraft. Research in recent years has shown that this demisability can depend heavily on how the expulsion of gaseous pyrolysis products through the outer surface of the material affects the heat flux at the surface. The ODPO has been developing a reduced-order model of the effect of pyrolysis gas blowing on the heat flux based on correlations between a blowing factor and a non-dimensional heat flux to be incorporated in the upcoming version 7.3 of the Object Reentry Survivability Analysis Tool (ORSAT). This presentation discusses the progress of this development project and the challenges remaining for generalizing the model across families of FRP materials.

Benton Greene↗

Advanced superposition methods for high speed turbopump vibration analysis

The small, high pressure Mark 48 liquid hydrogen turbopump was analyzed and dynamically tested to determine the cause of high speed vibration at an operating speed of 92,400 rpm. This approaches the design point operating speed of 95,000 rpm. The initial dynamic analysis in the design stage and subsequent further analysis of the rotor only dynamics failed to predict the vibration characteristics found during testing. An advanced procedure for dynamics analysis was used in this investigation. The procedure involves developing accurate dynamic models of the rotor assembly and casing assembly by finite element analysis. The dynamically instrumented assemblies are independently rap tested to verify the analytical models. The verified models are then combined by modal superposition techniques to develop a completed turbopump model where dynamic characteristics are determined. The results of the dynamic testing and analysis obtained are presented and methods of moving the high speed vibration characteristics to speeds above the operating range are recommended. Recommendations for use of these advanced dynamic analysis procedures during initial design phases are given.

Nielson, C. E.↗

Analytical Fuselage and Wing Weight Estimation of Transport Aircraft

A method of estimating the load-bearing fuselage weight and wing weight of transport aircraft based on fundamental structural principles has been developed. This method of weight estimation represents a compromise between the rapid assessment of component weight using empirical methods based on actual weights of existing aircraft, and detailed, but time-consuming, analysis using the finite element method. The method was applied to eight existing subsonic transports for validation and correlation. Integration of the resulting computer program, PDCYL, has been made into the weights-calculating module of the AirCraft SYNThesis (ACSYNT) computer program. ACSYNT has traditionally used only empirical weight estimation methods; PDCYL adds to ACSYNT a rapid, accurate means of assessing the fuselage and wing weights of unconventional aircraft. PDCYL also allows flexibility in the choice of structural concept, as well as a direct means of determining the impact of advanced materials on structural weight. Using statistical analysis techniques, relations between the load-bearing fuselage and wing weights calculated by PDCYL and corresponding actual weights were determined.

Chambers, Mark C.↗

Development and evaluation of a hybrid averaged orbit generator

A rapid orbit generator based on a first-order application of the Generalized Method of Averaging has been developed for the Research and Development (R&D) version of the Goddard Trajectory Determination System (GTDS). The evaluation of the averaged equations of motion can use both numerically averaged and recursively evaluated, analytically averaged perturbation models. These equations are numerically integrated to obtain the secular and long-period motion. Factors affecting efficient orbit prediction are discussed and guidelines are presented for treatment of each major perturbation. Guidelines for obtaining initial mean elements compatible with the theory are presented. An overview of the orbit generator is presented and comparisons with high precision methods are given.

Mcclain, W. D.↗

Multipath propagation study for L-band, over-ocean, satellite-aircraft communication link

The results are presented of a study of multipath propagation between an aeronautical relay satellite in synchronous earth orbit and an aircraft flying over the ocean. An analytical model for the reflected power is developed and the results of a computer solution are compared with an approximate solution obtained through integration by the method of steepest descent. The computer solution is shown to differ considerably from the approximate solution. Both methods are compared with the limited experimental results available.

Deal, J. H.↗

Wake vortex technology

A brief overview of the highlights of NASA's wake vortex minimization program is presented. The significant results of this program are summarized as follows: (1) it is technically feasible to reduce significantly the rolling upset created on a trailing aircraft; (2) the basic principles or methods by which reduction in the vortex strength can be achieved have been identified; and (3) an analytical capability for investigating aircraft vortex wakes has been developed.

Dunham, R. E., Jr.↗

Fast Generation of body conforming grids for 3-D

A fast algorithm was developed for accurately generating boundary conforming, three dimensional, consecutively refined, computational grids applicable to arbitrary axial turbomachinery geometry. The method is based on using a single analytic function to generate two dimensional grids on a number of coaxial axisymmetric surfaces positioned between the hub and the shroud. These grids are of the "O" type and are characterized by quasi-orthogonality, geometric periodicity, and an adequate resolution throughout the flowfield. Due to the built in additional nonorthogonal coordinate stretching and shearing, the grid lines leaving the trailing of the blade end at downstream infinity, thus simplifying the numerical treatment of the three dimensional trailing vortex sheet.

Dulikravich, O.↗

Dynamics of bi-periodic structures

In order to gain insight into the dynamics of biperiodic aerospace structures, a variety of one- and two-dimensional biperiodic structures are considered. It is shown that bands in which natural frequencies lie for periodic structures are further subdivided as a consequence of the biperiodicity. Analytical solutions for the modes and frequencies of finite-length one-dimensional biperiodic structures are obtained for general boundary conditions. A transmission method is developed to simplify the application of boundary conditions. Some modes are found to occur at frequencies outside the frequency bands predicted for biperiodic structures. Two-dimensional biperiodic crossed beam grillage and truss structures are considered in the present study.

Mcdaniel, T. J.↗

Uniform asymptotic approximations for duct eigenfunctions in a thin boundary layer flow

Analytical approximations for the acoustic modes in a duct carrying a uniform core flow with a thin shear layer at the walls are developed using the Method of Matched Asymptotic Expansions. Both two-dimensional and cylindrical duct propagation are considered. Numerical results for eigenvalues calculated using the theory are presented for the two dimensional problem and compared with results from earlier analyses. It is found that the new approximations yield a significant increase in accuracy.

Myers, M. K.↗

Launch vehicle aerodynamic data base development comparison with flight data

The aerodynamic development plan for the Space Shuttle integrated vehicle had three major objectives. The first objective was to support the evolution of the basic configuration by establishing aerodynamic impacts to various candidate configurations. The second objective was to provide continuing evaluation of the basic aerodynamic characteristics in order to bring about a mature data base. The third task was development of the element and component aerodynamic characteristics and distributed air loads data to support structural loads analyses. The complexity of the configurations rendered conventional analytic methods of little use and therefore required extensive wind tunnel testing of detailed complex models. However, the ground testing and analyses did not predict the aerodynamic characteristics that were extracted from the Space Shuttle flight test program. Future programs that involve the use of vehicles similar to the Space Shuttle should be concerned with the complex flow fields characteristics of these types of complex configurations.

Hamilton, J. T.↗

Film cooling heat transfer on a turbine airfoil

The objectives of the current program are to develop an analytical approach, based on boundary layer theory, for predicting the effects of airfoil cooling on downstream heat transfer rates and to verify the resulting analytical method by comparison of predictions with hot cascade data obtained under this program.

Hylton, Larry D.↗

Detailed modal testing of a solid rocket motor using a portable test system

Modern analytical techniques have expended the ability to evaluate solid rocket motors used in launch vehicles. As more detailed models of solid rocket motors were developed, testing methods were required to verify the models. Experimental modal analysis (modal testing) of space structures and launch vehicles has been a requirement for model validation for many years. However, previous testing of solid rocket motors has not typically involved dynamic modal testing of full scale motors for verification of solid propellant or system assembly properties. Innovative approaches to the testing of solid rocket motors were developed and modal testing of a full scale, two segment Titan 34D Solid Rocket Motor (SRM) was performed to validate detailed computer modeling. Special modifications were made to convert an existing facility into a temporary modal test facility which would accommodate the test article. The assembly of conventional data acquisition equipment into a multiple channel count portable system has made modal testing in the field feasible. Special purpose hydraulic exciters were configured to apply the dynamic driving forces required. All instrumentation and data collection equipment were installed at the test site for the duration of the test program and removed upon completion. Conversion of an existing test facility into a temporary modal test facility, and use of a multiple channel count portable test data acquisition system allowed all test objectives to be met and resulted in validation of the computer model in a minimum time.

Glozman, Vladimir↗