SEARCH · Engineering Papers

Results for “vibration testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

All sources NASA NTRS DOE OSTI

NASA NTRS1985

A normal incidence X-ray telescope sounding rocket payload

Progress is reported on the following major activities on the X-ray telescope: (1) complete design of the entire telescope assembly and fabrication of all front-end components was completed; (2) all rocket skin sections, including bulkheads, feedthroughs and access door, were specified; (3) fabrication, curing and delivery of the large graphite-epoxy telescope tube were completed; (4) an engineering analysis of the primary mirror vibration test was completed and a decision made to redesign the mirror attachment system to a kinematic three-point mount; (5) detail design of the camera control, payload and housekeeping electronics were completed; and (6) multilayer mirror plates with 2d spacings of 50 A and 60 A were produced.

Golub, L.↗

NASA NTRS1985

Investigation of composite materials property requirements for sonic fatigue research

Experimental techniques for determining the extensional and bending stiffness characteristics for symmetric laminates are presented. Vibrational test techniques for determining the dynamic modulus and material damping are also discussed. Partial extensional stiffness results intially indicate that the laminate theory used for predicting stiffness is accurate. It is clearly shown that the laminate theory can only be as accurate as the physical characteristics describing the lamina, which may vary significantly. It is recommended that all of the stiffness characteristics in both extension and bending be experimentally determined to fully verify the laminate theory. Dynamic modulus should be experimentally evaluated to determine if static data adequately predicts dynamic behavior. Material damping should also be ascertained because laminate damping is an order of magnitude greater than found in common metals and can significantly effect the displacement response of composite panels.

Patrick, H. V. L.↗

NASA NTRS1986

Experimental and analytical generic space station dynamic models

A dynamic model used for verification of analytical and experimental methods is documented. The model consists of five substructures to simulate the multibody, low frequency nature of large space structures. Design considerations which led to a fundamental vibration frequency of less than one Hz are described. Finite element analysis used to predict the vibration modes and frequencies of the experimental model is presented. In addition, modeling of cable suspension effects using prestressed vibration analysis is described. Details of the expermental and analytical models are included to permit replication of the study. Results of the modal vibration tests and analysis are presented in a separate document.

Belvin, W. K.↗

NASA NTRS1986

Differential stiffness effects

Differential stiffness as developed in NASTRAN is a linear change in stiffness caused by applied loads. Examples of differential stiffness are the stiffening effects of gravity forces in a pendulum, centrifugal forces in rotor blades and pressure loading of shell structures. In cases wherein this stiffness caused by a load is destabilizing, the differential stiffness concept lends itself to nonlinear structural analysis. Rigid Formats 4 (static analysis with differential stiffness) and 13 (normal modes with differential stiffness) are specifically designed to account for such stiffness changes. How pressure loading may be treated in these rigid formats is clarified. This clarification results from modal correlation of Ground Vibration Test (GVT) results from the empty and pressurized Filament Wound Case (FWC) quarter-scale Space Shuttle solid rocket booster (QSSRB). A sketch of the QSSRB cantilevered to the floor by its external tank attachments is shown.

Ujihara, B. H.↗

NASA NTRS1987

Filling an Unvented Cryogenic Tank

Slow-cooling technique enables tank lacking top vent to be filled with cryogenic liquid. New technique: pressure buildup prevented through condensation of accumulating gas resulting in condensate being added to bulk liquid. Filling method developed for vibration test on vacuum-insulated spherical tank containing liquid hydrogen.

Beck, Phillip↗

NASA NTRS1986

Oxide-dispersion-strengthened turbine blades, volume 1

The objective of Project 4 was to develop a high-temperature, uncooled gas turbine blade using MA6000 alloy. The program objectives were achieved. Production scale up of the MA6000 alloy was achieved with a fair degree of tolerance to nonoptimum processing. The blade manufacturing process was also optimized. The mechanical, environmental, and physical property evaluations of MA6000 were conducted. The ultimate tensile strength, to about 704 C (130 F), is higher than DS MAR-M 247 but with a corresponding lower tensile elongation. Also, above 982 C (180 F) MA6000 tensile strength does not decrease as rapidly as MAR-M 247 because the ODS mechanism still remains active. Based on oxidation resistance and diffusional stability considerations, NiCrAlY coatings are recommended. CoCrAly coating should be applied on top of a thin NiCrAlY coating. Vibration tests, whirlpit tests, and a high-rotor-rig test were conducted to ensure successful completion of the engine test of the MA6000 TFE731 high pressure turbine blades. The results of these tests were acceptable. In production quantities, the cost of the Project 4 MA6000 blade is estimated to be about twice that of a cast DS MAR-M 247 blade.

Millan, P. P., Jr.↗

NASA NTRS1987

Vibration isolation for line of sight performance improvement

Diagrams of the Reaction Wheel Assembly (RWA) are presented along with charts and graphs illustrating jitter error model, induced vibration tests, radial displacement transfer function, and axial displacement power spectra density. The RWA isolator specification requirements are listed.

Rodden, J. J.↗

NASA NTRS1986

Pultrusion process development for long space boom models

Long flexible boom models were required to develop ground vibration test methods for very low frequency space structures with applications to the proposed MAST program and Space Station. Pultruded quasi-isotropic composite beams were selected as an option over extruded aluminum alloy structures because of the lower cost potential, higher specific strength, flexural properties, and dynamic similarity considerations. A comparison is made of four different pultrusions having varied matrices and fiber orientations. Test results indicate that the pultrusion process can be used to produce quasi-isotropic composite structures by selective fiber orientation using the knit-lock fabric concept.

Wilson, Maywood L.↗

NASA NTRS1987

Recent advances in structural dynamics of large space structures

Recent progress in the area of structural dynamics of large space structures is reviewed. Topics include system identification, large angle slewing of flexible structures, definition of scaling limitations in structural models, and recent results on a tension-stabilized antenna concept known as the hoop-column. Increasingly complex laboratory experiments guide most of the activities leading to realistic technological developments. Theoretical progress in system identification based on system realization theory resulting in unification of several methods is reviewed. Experimental results from implementation of a theoretical large-angle slewing control approach are shown. Status and results of the development of a research computer program for analysis of the transient dynamics of large angle motion of flexible structures are presented. Correlation of results from analysis and vibration tests of the hoop-column antenna concepts are summarized.

Pinson, Larry D.↗

NASA NTRS1988

Predicted and measured strain responses of isotropic panels to base excitation

The accuracy of classical linear theory for predicting acceleration and strain for cantilevered and Clamped-Free-Clamped-Free (C-F-C-F) panels excited through the base is studied. Aluminum, steel and titanium plates of various dimensions and thicknessess were vibration tested, using a broadband random signal applied through a shaker mounting fixture. The strains were measured at 9 locations on the cantilevered panels and at 5 locations on the C-F-C-F panels. Predictions were based on the Ritz method. The measured accelerations of the base were input to the analysis for the forcing function. Comparisons between predicted and measured strain acceleration spectra were within an average error of 20 percent for both the cantilevered and C-F-C-F panels.

Lyle, Karen H.↗

NASA NTRS1987

Recent advances in structural dynamics of large space structures

Pinson, Larry D.↗

NASA NTRS1988

The nonlinear behavior of a passive zero-spring-rate suspension system

Various concepts for advanced syspension systems have been proposed for counteracting gravity loads in ground vibration testing of large space structures. Approximating the flight modes of a low-frequency flexible structure in a ground test requires a very soft suspension system. The dynamic behavior of a passive zero-spring-rate mechanism, sometimes used for such ground testing, is analyzed. This mechanism reduces the stiffness inherent in suspending a test specimen by cables. However, the mechanism is shown to be sensitive to imperfections. Imperfections can initiate nonlinear behavior which becomes more pronounced at lower operating frequencies. Furthermore, large pendular motion of the suspension system couples with the vertical motion, producing additional nonlinearity.

Woodard, Stanley E.↗

NASA NTRS1989

Digital Controller For Acoustic Levitation

Acoustic driver digitally controls sound fields along three axes. Allows computerized acoustic levitation and manipulation of small objects for such purposes as containerless processing and nuclear-fusion power experiments. Also used for controlling motion of vibration-testing tables in three dimensions.

Tarver, D. Kent↗

NASA NTRS1988

The effects of excitation waveforms and shaker moving mass on the measured modal characteristics of a 2- by 5-foot aluminum plate

Ground vibration tests were conducted to compare and to investigate the effects of five excitation waveforms and the shaker moving mass (equipment and armature used to attach the shaker to the structure) on the experimental modal characteristics of a 2- by 5-ft aluminum plate using fast Fourier transform techniques. The five types of excitation waveforms studied were sine dwell, random, impact, sine sweep, and impulsive sine. The results showed that the experimental modal frequencies for all types of excitation were within 3 percent, while the modal damping data exhibited greater scatter. The sets of mode shapes obtained by the five types of excitation were consistent. The results of the shaker moving mass investigation on the 2- by 5-ft aluminum plate showed that modal frequency decreases and modal damping remains relatively constant with an increase in shaker moving mass. The generalized mass of the structure appears to decrease with an increase in shaker moving mass. In addition, it was seen that having a shaker near a node line can reduce some of the effects of the added shaker moving mass on the frequencies and the damping.

Voracek, David F.↗

NASA NTRS1989

Comparison of predicted and measured temperatures of UH-60A helicopter transmission

The 2109-kW (2828-hp) UH-60A Black Hawk helicopter transmission was one of the transmissions used to obtain an experimental data base. Component improvements or new transmission concepts can thus be evaluated by comparison with the established data. Results of efficiency and vibration tests of the UH-60A have been reported previously. In this investigation the transmission was instrumented internally and tested over a range of operating conditions. The speed was varied from 50 to 100 percent of the full rated value, and the torque was varied from 10 to 100 percent of the full rated value. Temperatures of internal bearings and gears were measured. The computer program Planetsys was used to simulate the thermal performance of this transmission. The calculated temperatures were then compared with the corresponding measured values. The highest measured temperature was 405 K (270 F) on the outer race of the high-speed input shaft roller bearing, at the 100-percent power condition. In general, the predicted temperatures compared very well with the measured values, most of them being within 5 kelvin (9 F). Specifically, the temperatures predicted for the single-row spherical roller planetary bearing averaged only about 4 kelvin (8 F) lower than the highest measured value.

Coe, Harold H.↗

NASA NTRS1988

Pultrusion Process Development for Long Space Boom Model

Long flexible-boom models were required to develop ground-vibration test methods for very-low-frequency space structures with applications to the proposed Space Station. Pultruded quasi-isotropic composite beams were selected as an option over extruded aluminum alloy structures because of the lower cost potential, the higher specific strength, the flexural properties, and the dynamic similarity considerations. The reinforcement material that was used was biaxial (0 deg/90 deg) fiberglass roving held in place with knitted polyester yarn such that equal fiber volume in 0 deg and 90 deg orientations provided nearly equal strength in both longitudinal and transverse directions. An isophthalic polyester resin system was used as the matrix. Continuous lengths up to 270 ft were easily pultruded with biaxial fabric. Tracking problems were encountered with similar unidirectional fabrics. Analyses of processing problems were conducted to determine causes for delamination, scaling, and sloughing. Ultrasonic C-scanning and scanning electron microscope examinations were conducted as well as mechanical testing to failure. Test results indicate that pultrusion processes can be used to produce quasi-isotropic composite structures.

Wilson, Maywood L.↗

NASA NTRS1990

Plan, execute, and discuss vibration measurements and correlations to evaluate a NASTRAN finite element model of the AH-64 helicopter airframe

A ground vibration test was performed on the AH-64 (Apache) helicopter to determine the frequency response of the airframe. The structure was excited at both the main and tail rotor hubs, separately, and response measurements were taken at 102 locations throughout the fuselage structure. Frequency responses were compared and correlated with results from a NASTRAN finite element model of AH-64. In addition, natural frequencies and mode shapes were estimated from the frequency response data and were correlated with analytical results.

Ferg, D.↗

NASA NTRS1989

A multi-point force appropriation method based upon a singular value decomposition approach

Force appropriation methods aim to provide an estimate for the force pattern required to excite a 'pure' normal mode in a vibration test where multiple exciters are available. In this paper, a new method based upon a Singular Value Decompositon approach is presented. The appropriated force vector which minimizes the in-plane response components while maximizing the required quadrature components is found, subject to a fixed force norm. The method can accommodate more transducers than exciters and also more exciters than effective degrees of freedom. The method is demonstrated upon a six degree of freedom theoretical model and it is shown that an estimate for the effective degrees of freedom can be obtained.

Juang, Jer-Nan↗