SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This study highlights the importance of mid-infrared spectral signatures and discusses the fundamental mechanisms driving charge transport in COFs. Our analysis can hopefully guide the rational design of new COFs yielding higher conductivities.
Efficient lithium recovery from geothermal brines is crucial for the battery industry. Current electrochemical separation methods struggle with the simultaneous presence of Na + , K + , Mg 2+ , and Ca 2+ because these cations are similar to Li + , making it challenging to separate effectively. We address these challenges with a three-chamber reactor featuring a polymer porous solid electrolyte in the middle layer. This design improves the transference number of Li + (t Li+ ) by 2.1 times compared to the two-chamber reactor and also reduces the chlorine evolution reaction, a common side reaction in electrochemical lithium extraction, to only 6.4% in Faradaic Efficiency. Employing a lithium-ion conductive glass ceramic (LICGC) membrane, the reactor achieved high t Li+ of 97.5% in LiOH production from simulated brine, while the concentrations of Na + K + , Mg 2+ , and Ca 2+ are below the detection limit. Electrochemical experiments and surface analysis elucidated the cation transport mechanism, highlighting the impact of Na + on Li + migration at the LICGC interface.
We report the synthesis and characterization of phase pure Ta 3 Sb, a material predicted to be topological with eightfold degenerate fermionic states [Bradlyn et al., Science 353, aaf5037 (2016)] and to exhibit a large spin Hall effect [Derunova et al., Sci. Adv. 5, eaav8575 (2019)]. We observe superconductivity in Ta 3 Sb with T c ~0.67 K in both electrical resistivity ρ(T) and specific heat c(T) measurements. Field-dependent measurements yield the superconducting phase diagram with an upper critical field of H c2 (0) ~0.95 T, corresponding to a superconducting coherence length of ξ ≈ 18.6 nm. The gap ratio deduced from specific heat anomaly, 2Δ 0 /k B T c is 3.46, a value close to the Bardeen-Cooper-Schrieffer value of 3.53. From a detailed analysis of both the transport and thermodynamic data within the Ginsburg-Landau (GL) framework, a GL parameter of κ ≈ 90 is obtained, identifying Ta 3 Sb as an extreme type-II superconductor. The observation of superconductivity in an eightfold degenerate fermionic compound with topological surface states and predicted large spin Hall conductance positions Ta 3 Sb as an appealing platform to further explore exotic quantum states in multifold degenerate systems.
Superconducting detectors with sub-eV energy resolution have demonstrated success setting limits on Beyond the Standard Model (BSM) physics due to their unique sensitivity to low-energy events. G4CMP, a Geant4-based extension for condensed matter physics, provides a comprehensive toolkit for modeling phonon and charge dynamics in cryogenic materials. This paper introduces a technical formalism to support the superconducting qubit and low-threshold detector community in implementing phonon simulations in custom materials into the G4CMP. As a case study, we present the results of a detailed analysis of silica phonon transport properties relevant for simulating substrate backgrounds in Beryllium Electron capture in Superconducting Tunnel junctions (BeEST)-style experiments using G4CMP. Additionally, Python-based tools were developed to aid users in implementing their own materials and are available on the G4CMP repository.
Summary In natural environments, plants are exposed to rapidly changing light. Maintaining photosynthetic efficiency while avoiding photodamage requires equally rapid regulation of photoprotective mechanisms. We asked what the operation frequency range of regulation is in which plants can efficiently respond to varying light. Chlorophyll fluorescence, P700, plastocyanin, and ferredoxin responses of wild‐types Arabidopsis thaliana were measured in oscillating light of various frequencies. We also investigated the npq1 mutant lacking violaxanthin de‐epoxidase, the npq4 mutant lacking PsbS protein, and the mutants crr2‐2 , and pgrl1ab impaired in different pathways of the cyclic electron transport. The fastest was the PsbS‐regulation responding to oscillation periods longer than 10 s. Processes involving violaxanthin de‐epoxidase dampened changes in chlorophyll fluorescence in oscillation periods of 2 min or longer. Knocking out the PGR5/PGRL1 pathway strongly reduced variations of all monitored parameters, probably due to congestion in the electron transport. Incapacitating the NDH‐like pathway only slightly changed the photosynthetic dynamics. Our observations are consistent with the hypothesis that nonphotochemical quenching in slow light oscillations involves violaxanthin de‐epoxidase to produce, presumably, a largely stationary level of zeaxanthin. We interpret the observed dynamics of photosystem I components as being formed in slow light oscillations partially by thylakoid remodeling that modulates the redox rates.
Dataset 3: A National Dataset on Actionable Items in Improving Pooled Rideshare.” 2025. Dataset Description: Pooled Rideshare Acceptance Survey - Phase 3 (2025, N = 8,296). This dataset represents the third and final phase of a national survey aimed at understanding user acceptance and preferences related to pooled rideshare (PR) services in the United States. Building on insights from earlier phases, this phase expands both the sample size and the depth of analysis to support policymaking, transportation planning, and service design for sustainable mobility systems. The Phase 3 survey was administered online to a nationally representative sample of 8,296 U.S. adults. The sample includes a wide range of demographics. The survey retained core questions from previous phases while introducing 77 detailed service features (actionable items) to evaluate potential improvements to PR offerings. Each feature was designed to assess whether a specific improvement, such as enhanced safety measures, real-time ride tracking, or user training would increase participants’ willingness to adopt PR services. In addition, behavioral predictors, current rideshare habits, environmental attitudes, and perceived barriers (e.g., safety, privacy, and comfort) were captured. - Phase_3_Final - The dataset contains rows corresponding to individual respondents and columns representing survey items, demographic characteristics, and response values. The data is available in both .CSV and .SAV formats. - Phase_3_Final_MapFile - Accompanying this dataset is a data dictionary explaining each variable, value range, and coding schema. An .XLSX format of the full survey instrument is included to support interpretation and reuse of the dataset.
The study of x-ray induced rapid heating and the resulting material responses - (thermomechanical shock (TMS) and thermo-structural response (TSR)) - is important to our understanding of material behavior in extreme environments. A series of high conversion efficiency (XRCE) x-ray sources have been developed for the NIF laser facility ranging in fluence and spectral content. In conjunction with source development, we have developed a new XTRRA (X-ray Transport and Radiation Response Analysis) test cassette to hold a set of samples, each at equal distance from target chamber center (TCC) where the x-ray source is placed. Design and performance details of the x-ray sources is discussed elsewhere. Here, we describe the development and use of this TMS XTRRA test cassette. The XTRRA test cassette is a snout mounted on a NIF Diagnostic Instrument Manipulator (DIM) designed to position six samples equidistant from the x-ray source to assure uniform irradiation of all samples. Photon Displacement interferometry (PDI) is used to measure the displacement of the rear surface of each sample resulting from x-ray exposure on the front of the sample. This will help determine the x-ray generated impulse on the sample. The samples are retrieved from the snout after the shot for inspection and post-shot analysis including the measurement of sample ablated mass and engineering tests examining changes in the material structure. The data from experiments are compared to predictions from LLNL’s ASC codes and used to inform models implemented in these codes. Thus, XRCE x-ray sources with the XTRRA snout at the National Ignition Facility (NIF) laser at the Lawrence Livermore National Laboratory [1,2] provide the ability to expose a broad range of material samples directly to high x-ray fluence, measure shock transits, and recover the sample for further analysis post-shot.
The U.S. Department of Energy’s Vehicle Technologies and Hydrogen and Fuel Cell Technologies Offices (VTO and HFTO) support research and development of efficient and sustainable transportation technologies that will improve energy efficiency, minimize emissions, and enable America to use less petroleum. VTO and HFTO regularly revisit and update relevant research and development goals and areas of emphasis in response to the latest technological advancements and in alignment with current national priorities. As such, analyses of expected benefits resulting from VTO and HFTO investments and anticipated goal achievements are updated periodically and will be again for 2021 in the context of the latest national-level transportation decarbonization goals. The analysis in the present report is based on technical progress goals established in VTO and HFTO in the years immediately prior to and including 2020, and it summarizes the estimated energy and emissions benefits corresponding to achievement of those goals. The goals span research activities on batteries, electric drive technologies (EDT), combustion, lightweight materials, fuel cells, and hydrogen storage. The evaluation includes detailed analyses into the benefits of technology improvements on the U.S. light-duty (LD) vehicle fleet and separately on the U.S. medium- and heavy-duty (MDHD) vehicle fleet. This report summarizes the outcomes from each of these analyses both independently and in combination.
This presentation discusses the UNF-ST&DARDS which performs many analyses for as-loaded SNF canisters, including criticality safety, shielding, thermal-hydraulic, and containment. It also discusses the experiment selection based on c k assessment of similarity and that the c k value of 0.8 or greater considered applicable for validation. 11 PWR SNF canisters (MPC-32) are used in this work. 1 model represents a failed fuel assembly as fresh, per the design basis and the remaining 10 models represent all 32 assemblies with depleted fuel. In conclusion, critical experiment selection can be performed with S/U techniques for as-loaded canisters in UNF-ST&DARDS. Sufficient benchmark experiments exist to support validation and additional MOX experiments that are a good match for commercial SNF would be a benefit to provide independent data. The presentations states that S/U techniques identify different pools of experiments for different systems and that the process is amenable to automation within UNF-ST&DARDS.
During this DOE grant, DE-SC0017890, in place for the past six years, all proposed research was carried out and published in peer-reviewed papers, as well as other projects that emerged during the research. In that effort the research team accomplished all proposed research, as well as many closely related research projects discovered and conceived of during the grant. These works included “Efficient Quantum Measurement Engines”, a work published in Physical Review Letters, giving a theory of quantum measurement-based engines, which uses quantum measurement as a resource. These engines are designed to efficiently convert energy from the stochastic quantum measurement process into useful work. Further publications include “Experimental Realization of a Quantum Dot Energy Harvester”, a joint theory and experimental work in collaboration with the group of Charles Smith in Cambridge, UK, as well as long time theoretical collaborators, Rafael Sánchez and Björn Sothmann. This work, featured as an Editor’s Suggestion in Physical Review Letters, realized an earlier theoretical proposal of ours, whereby two resonant tunneling quantum dots are connected to a central electronic cavity that is heated by a hot energy source. We also published “Superconducting Quantum Refrigerator: Breaking and Rejoining Cooper Pairs with Magnetic Field Cycles” a work done in collaboration with experimentalist Francesco Giazotto from ENS Pisa, Italy, which also resulted in a patent. This paper, published in Phys. Rev. Applied, advanced the concept of a cyclic fridge based on the normal/superconducting phase transition together with layered materials separated by tunnel junctions. We also completed the proposed research on a heat transistor, publishing “Thermal transistor and thermometer based on Coulomb-coupled conductors”, carried out as a collaboration between my group and theorists Splettstoesser (Lund U., Sweden), Sothmann (U. Duisburg-Essen, Germany), and Sánchez (U. Autónoma de Madrid, Spain). We carried out an analysis of a quantum coupled to a quantum point contact as a sensitive thermometer and heat transistor. We found the optimal statistical estimator for the temperature and compared it with experiments on the same type of devices. We also investigated autonomous quantum absorption refrigerators using quantum dots to cool by using a very hot thermal reservoir to drive heat between two other reservoirs. In the article “Quantifying the quantum heat contribution from a driven superconducting circuit”, we demonstrated that for a driven superconducting circuit, we showed heat flow provided by a hot source to the qubit can be switched on and off by varying external parameters, the frequency and the intensity of the driving. In the work “Stochastic thermodynamic cycles of a mesoscopic thermoelectric engine”, we reconsidered the autonomous thermoelectric heat engine in terms of underlying cycles. Rather than periodic behavior, the cycles were stochastic in nature. Nevertheless, by undertaking a graph theoretical analysis of the elementary transport processed, great quantitative and qualitative insight could be found. We also considered the quantum measurement process and showed that a quantum version of Maxwell’s demon could be related to the work extraction of a quantum system, closely related to arrow-of-time measures for quantum measurement, as described in our article “Thermodynamics of quantum measurement and Maxwell's demon's arrow of time”. This work was selected in Phys. Rev. A as an Editor’s Suggestion. A recent preprint titled “Cyclic Superconducting Quantum Refrigerators Using Guided Fluxon Propagation” accomplished an important piece of this grant: to propose a new kind of quantum refrigerator using the dynamics of fluxons in a type II superconductor. This invention envisioned a race-track type geometry where fluxons are confined. By applying a gradient of magnetic field together with electric current in a Corbino geometry, the circulating fluxons can actively cool a cold reservoir, realizing a new type of cyclic superconducting refrigerator. We also investigated the possibility of thermal control from different points of view. The application of quantum measurement to the system gives a new kind of control on the system of interest – we have pioneered this approach and shown that measurement can boost the thermal power of quantum engines as described in “Continuous measurement boosted adiabatic quantum thermal machines”. The ability to have heat flows on demand is an outstanding challenge, and we have provided new solutions to this problem in Thermal control across a chain of electronic nanocavities” for a chain of electron cavities using gating voltage control. The control methods using qubit/qubit coupling to create absorption fridges at their most fundamental level have also been developed.
We will develop structural mechanics models that capture the evolution of feedstock attributes during the Forest Concepts comminution process. Models will be validated by data provided by Forest Concepts and experiments performed by synergistic projects within the Feedstock Conversion Interface Consortium.
Performance potential of liquid hydrogen fueled hypersonic commercial transport, considering economics, mission analysis and passenger appeal
A general formulation of some effects of swirl on turbulent mixing is given. The basis for the analysis is that momentum transport is enhanced by turbulence resulting from rotational instability of the fluid field. An appropriate form for the turbulent eddy viscosity is obtained by mixing length type arguments. The result takes the form of a corrective factor that is a function of the swirl and acts to increase the eddy viscosity. The factor is based upon the initial mixing conditions implying that the rotational turbulence decays in a manner similar to that of free shear turbulence. Existing experimental data for free jet combustion are adequately matched by using the modifying factor to relate the effects of swirl on eddy viscosity. The model is extended and applied to the supersonic combustion of a ring jet of hydrogen injected into a constant area annular air stream. The computations demonstrate that swirling the flow could: (1) reduce the burning length by one half, (2) result in more uniform burning across the annulus width, and (3) open the possibility of optimization of the combustion characteristics by locating the fuel jet between the inner wall and center of the annulus width.
The integration of a compact thermoelectric converter with a 5-kwe reactor system is described. Material interaction uncertainties study is also presented. This includes degradation of the required austenitic - refractory metal transition joint during operation at high temperatures; loss of corrosion resistance; embrittlement by the presence of hydrogen; and loss of design margin by transport of interstitial elements. Analysis and limited experimental evidence indicate that these potential materials interactions can be adequately controlled. Group 5-2 refractory metals can be utilized without unacceptable adverse effect on system reliability.
The Earth Resources Technology Satellite (ERTS-1) launched by NASA in July 1972 has been providing thousands of high resolution multispectral images of interest to geographers, cartographers, hydrologists, and agroculturists. It has been found possible to detect the long-range (over 50 km) transport of suspected particulate plumes from the Chicago-Gary steel mill complex over Lake Michigan. The observed plumes are readily related to known steel mills, a cement plant, refineries, and fossil-fuel power plants. This has important ramifications when discussing the interregional transport of atmospheric pollutants. Analysis reveals that the Multispectral Scanner Band 5 (0.6 to 0.7 micrometer) provides the best overall contrast between the smoke and the underlying water surface.
This paper summarizes the scope, analytical methods, and principal findings of a recently performed Space-Tug economic analysis. Both the Shuttle/Tug transportation system and its unmanned payloads were modeled in this study. A variety of upper-stage concepts capable of fulfilling the Tug mission were evaluated against this model, and the 'best' Tug concepts were identified for a range of economic measures.
Oceanographic field measurements have revealed intense, transient mesoscale motions in many parts of the world ocean. The circulation of the western North Atlantic, considered in the present study as a rectangular basin, is simulated with a primitive equation model that has five levels and a horizontal grid size of 37 km. The model ocean is driven by a 2.5 gyre pattern of steady zonal wind stress and by a Newtonian-type surface heating. Two cases are considered: the first uses a Laplacian formulation for the subgrid-scale lateral diffusions of heat and momentum; the second uses a highly scale-selective biharmonic formulation for these diffusions. An analysis of the heat transport, in the biharmonic experiment, shows that the horizontal transport of heat by eddies is much larger than the subgrid-scale horizontal heat diffusion. In the Gulf Stream region, the eddy heat transport is comparable to the effect of a lateral diffusion coefficient of 10 to the 7th sq cm/s.
The considered study has been conducted to evaluate the future potential for an advanced air cargo transport. A current operations analysis is discussed, taking into account the traffic structure, modal cost comparisons, terminal operations, containerization, and institutional factors. Attention is also given to case studies, a demand forecast, and an advanced air cargo systems analysis. The effects of potential improvements on reducing costs are shown. Improvement to the current infrastructure can occur from 1978 to 1985 with off-the-shelf technology, which when combined with higher load factors for aircraft and containers, can provide up to a 16 percent reduction in total operating costs and a 15 percent rate reduction. The results of the analysis indicate that the proposed changes in the infrastructure and improved cargo loading efficiencies are as important to improving the airlines' financial posture as is the anticipated large dedicated cargo aircraft.