Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transfer maps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Analysis of heat transfer for a normally impinging liquid-metal slot jet

A two-dimensional liquid-metal slot jet that is impinging normally against a uniformly heated flat plate is analyzed. The distributions of wall temperature and heat-transfer coefficient are obtained as functions of position along the plate. The liquid-metal assumptions are made that the jet is inviscid and that molecular condition is dominating heat diffusion. The solution is obtained by mapping the jet flow region into a potential plane where it occupies a strip of uniform width. The energy equation is transformed into potential coordinates, and an exact solution obtained in the strip region. Conformal mapping is then used to transform the solution into the physical plane.

Siegel, R.↗
NASA NTRS1983

Minimal upper mantle temperature variations consistent with observed heat flow and plate velocities

Heat-flow and plate-velocity measurements are used to model upper-mantle temperature variations; the results are intended to form the basis for a gravity-field-variation model and are also applicable to the interpretation of petrological and seismological data. A 5-deg grid is used, a depth of 280 km is chosen as the fully convecting level, and it is assumed that 85 percent of the global heat production (4.0 x 10 to the 13th W) comes from below this level. The velocity field is calculated by integrating the momentum equations down to 280 km (assuming laterally homogeneous viscosity and density) and then used to determine the temperature fields. The results are presented in graphs, tables, and maps. The largest lateral temperature differences are about 1500 C and occur in the top 20 km, where the largest (about 200 C/Myr) nonlinear terms of the energy equation are also found. Below 50 km, heat transfer becomes more convective than conductive, and the most significant temperature variation appears in the form of negative 'tongues' as cold as -825 C at about 100 km. Temperature variations of at least + or - 180 C are calculated at the fully convecting level.

Kaula, W. M.↗
NASA NTRS1999

Microgravity Two-Phase Flow Transition

Two-phase flows under microgravity condition find a large number of important applications in fluid handling and storage, and spacecraft thermal management. Specifically, under microgravity condition heat transfer between heat exchanger surfaces and fluids depend critically on the distribution and interaction between different fluid phases which are often qualitatively different from the gravity-based systems. Heat transfer and flow analysis in two-phase flows under these conditions require a clear understanding of the flow pattern transition and development of appropriate dimensionless scales for its modeling and prediction. The physics of this flow is however very complex and remains poorly understood. This has led to various inadequacies in flow and heat transfer modeling and has made prediction of flow transition difficult in engineering design of efficient thermal and flow systems. In the present study the available published data for flow transition under microgravity condition are considered for mapping. The transition from slug to annular flow and from bubbly to slug flow are mapped using dimensionless variable combination developed in a previous study by the authors. The result indicate that the new maps describe the flow transitions reasonably well over the range of the data available. The transition maps are examined and the results are discussed in relation to the presumed balance of forces and flow dynamics. It is suggested that further evaluation of the proposed flow and transition mapping will require a wider range of microgravity data expected to be made available in future studies.

Parang, M.↗
NASA NTRS1999

Modeling of Sub-Grid Heterogeneity and its Impact on GCM Global Radiation Balance

The spatial and temporal variability of high, low, and mid-level clouds is obtained from ISCCP D1 data. Monthly mean global maps of the observed cloud variability are used to re-scale GCM prognostic cloud optical depths and radiative parameters via the Monte Carlo cloud heterogeneity parameterization that utilizes the existing plane-parallel GCM radiative transfer model to compute radiative fluxes for inhomogeneous cloud distributions. The GCM radiative fluxes at TOA and the ground surface are then compared to ERBE and GEBA results. These comparisons show that including sub-grid cloud variability in the GCM radiative model improves agreement between the GCM radiative energy budget components and observations,

Lacis, Andrew↗
NASA NTRS2007

Application of Satellite and Ground-based Data to Investigate the UV Radiative Effects of Australian Aerosols

An understanding of the effect of aerosols on biologically- and photochemically-active UV radiation reaching the Earth's surface is important for many ongoing climate, biophysical, and air pollution studies. In particular, estimates of the UV characteristics of the most common Australian aerosols will be valuable inputs to UV Index forecasts, air quality studies, and assessments of the impact of regional environmental changes. By analyzing climatological distributions of Australian aerosols we have identified sites where co-located ground-based UV-B and ozone measurements were available during episodes of relatively high aerosol activity. Since at least June 2003, surface UV global irradiance spectra (285-450 nm) have been measured routinely at Darwin and Alice Springs in Australia by the Australian Bureau of Meteorology (BoM). Using colocated sunphotometer measurements at Darwin and Alice Springs, we identified several episodes of relatively high aerosol activity. Aerosol air mass types were analyzed from sunphotometer-derived angstrom parameter, MODIS fire maps and MISR aerosol property retrievals. To assess aerosol effects we compared the measured UV irradiances for aerosol-loaded and clear-sky conditions with each other and with irradiances simulated using the libRadtran radiative transfer model for aerosol-free conditions. We found that for otherwise similar atmospheric conditions, smoke aerosols over Darwin reduced the surface UV irradiance by as much as 40-50% at 290-300 nm and 20-25% at 320-400 nm near active fires (aerosol optical depth, AOD, at 500 nm approximately equal to 0.6). Downwind of fires, the smoke aerosols over Darwin reduced the surface irradiance by 15-25% at 290-300 nm and approximately 10% at 320-350 nm (AOD at 500 nm approximately equal to 0.2). The effect of smoke increased with decrease of wavel strongest in the UV-B. The aerosol attenuation factors calculated for the selected cases suggest smoke over Darwin has an effect on surface 340-380 nm irradiances that is comparable to that produced by smoke over Sub-Saharan Africa. Dust activity was very low at Alice Springs during 2004, therefore we were not able to identify strong dust events to fully assess the UVeffect of dust. For the cases studied, smoke aerosols seem to produce a stronger reduction in surface UV irradiances than dust aerosols.

UV surface irradiances↗
DOE OSTI2025

Paleoclimatic implications of glacial fluctuations in the Sierra Nevada del Cocuy, northern Andes, Colombia, during the Lateglacial and Holocene

The reconstruction of former mountain glaciers from geomorphic mapping and cosmogenic-nuclide surface-exposure dating provides a unique opportunity to infer patterns of past terrestrial climate variability. Tropical mountain glaciers are particularly valuable as there are comparatively few terrestrial climate proxies at equatorial latitudes relative to higher latitudes. As the single largest climate zone on Earth, the tropics play an outsized role in mediating global climate via the ocean-atmosphere transfer of latent heat and water vapor. Nonetheless, there remains a persistent gap in our understanding of how the tropics influenced – or were influenced by – the high-magnitude climate shifts of the Late Pleistocene, and whether this high-energy region simply responded to extratropical forcing or was itself a driver of global climatic change. To help address this knowledge gap, we analyzed geologic evidence for past glacial fluctuations in three adjacent valleys in the Sierra Nevada del Cocuy, the highest subrange of the Eastern Cordillera in the Colombian Andes, to provide a terrestrial record of atmospheric temperature during the latter part of Termination 1. Coupled with geomorphic mapping and paleo-snowline reconstructions, our beryllium-10 glacial chronology indicates that glaciers in the humid inner tropics underwent pronounced growth and gradual decay during the Antarctic Cold Reversal (14.5–12.8 ka) and Younger Dryas (12.8–11.7 ka) periods, respectively, following a trend that, according to directly dated moraine records from throughout both polar hemispheres, appears to have been global. While the specific mechanism(s) behind this large-scale behavior remains to be corroborated, we revisit the hypothesis that ocean-atmosphere heat transfer and water vapor flux are key drivers of abrupt Lateglacial temperature fluctuations. Subsequent to the Lateglacial, deglaciation of the Sierra Nevada del Cocuy accelerated during the Early Holocene, a pattern also observed in other tropical glacier records. More recently, the magnitude of snowline rise and glacier retreat over the last two centuries supports the view that modern tropospheric warming is anomalously strong at least relative to the last ∼16,000 years.

Andes↗
DOE OSTI2026

Exploring Excited State Proton Transfer Dynamics upon Ultraviolet Excitation

Excited state intramolecular proton transfer (ESIPT) has been investigated in two prototypical systems─salicylaldehyde azine (SAA) and 1,5-dihydroxyanthraquinone (DHAQ)─using transient absorption spectroscopy upon ultraviolet excitation into the less studied higher excited (S n ) manifold. Excitation with sub-30 fs pulses and broadband visible probing has allowed for direct measurement of the ESIPT rate. In conjunction with steady-state measurements and TD-DFT calculations, a complete delineation of the ultrafast photophysics has been carried out. In SAA, ESIPT remains ultrafast (∼30 fs), consistent with previous S 1 excitation studies. Coherent vibrational beats maps reveal significant wavelength dependence, however. Theoretical analysis suggests that the observed modes and their intensities in coherent vibrational spectra are modulated by the nature of the electronically excited state. In DHAQ, the first direct observation of ESIPT presents a time-constant of ∼85 fs, and a slower component of 9 ps, akin to previous reports on double-proton transfer systems. Collectively, the results suggest that while the ultrafast ESIPT rate remains largely invariant vis-à-vis the excitation energy, the product yield, as well as accompanying coherent oscillations, may be substantively altered, owing to the existence of alternative decay pathways.

excited states↗
DOE OSTI2024

A novel transient infrared imaging method for non-intrusive, low-cost, fast, and accurate air leakage detection in building envelopes

Air leakage through the building envelope in the U.S. accounts for about four quads of energy annually, costing approximately $40 billion per year. However, a high-fidelity and non-intrusive method to detect air leakage has not been demonstrated to date. Here, in this paper, we propose a novel non-intrusive and low-cost method called Transient Infrared (IR) Imaging (TIRI) that can rapidly and accurately identify air leakage locations and relative rates on building envelopes. When the interior and exterior temperatures are different, and a small internal pressure pulse is created by HVAC, the temperature at locations with air leakages will change rapidly, while the areas without a leakage do not change. Based on a heat transfer model, we have derived the temperature change as a function of time after the HVAC is turned on. By tracking the temperature change, which depends on leakage rate and size, we have obtained the air leakage map in the case studies. Using an exterior door as an example, we took transient IR images in different seasons and different times of the day, and successfully obtained the leakage map in all the scenarios. Successfully obtained the air leakage map even when the indoor-outdoor air temperature difference is as small as 2 °C. We have also realized a detection speed of 10s and demonstrated that this method also worked for windows, which have mirror-like IR reflections. Our TIRI method will accelerate the improvement of airtightness in buildings, save building energy, and help reduce greenhouse gas emissions.

42 ENGINEERING↗
DOE OSTI2025

Unlocking expanded flagellin perception through rational receptor engineering

Abstract The surface-localized receptor kinase FLS2 detects the flg22 epitope from bacterial flagella. FLS2 is conserved across land plants, but bacterial pathogens exhibit polymorphic flg22 epitopes. Most FLS2 homologues possess narrow perception ranges, but four with expanded perception have been identified. Using diversity analyses, AlphaFold modelling and amino acid properties, key residues enabling expanded recognition were mapped to FLS2’s concave surface, interacting with the co-receptor and polymorphic flg22 residues. Synthetic biology enabled engineering of expanded recognition from QvFLS2 (Quercus variabilis) into a homologue with canonical perception. A similar approach enabled transfer ofAgrobacteriumperception from FLS2 XL (Vitis riparia) into VrFLS2. Evolutionary analyses across three plant orders showed residues under positive selection aligning with those binding the co-receptor and flg22’s C terminus, suggesting more alleles with expanded perception exist. Our experimental data enabled the identification of specific receptor amino acid properties and AlphaFold3 metrics that facilitate predicting FLS2–flg22 recognition. This study provides a framework for rational receptor engineering to enhance pathogen restriction.

Plant Sciences↗
DOE OSTI2024

Improving Cost and Efficiency of the Scalable Solid Oxide Fuel Cells Power System

The objective of this project was to design and develop a 20kW range small-scale solid oxide fuel cells (SOFC) power system for applications such as data centers and commercial buildings. The original plan included a 5,000 hours demonstration and a Techno-Economic Analysis (TEA) which were dropped as part of project termination. The original project plan was to use a stack with a cross-flow cell design which had previously been tested for 500 hours at a community college in Malta, NY. However, it was decided to move to the advanced R-SOFC co-flow cell developed under Department of Energy Award DE-FE0031971. The advanced cell design has the advantage of a larger active area for the same manufacturing footprint which results in fewer required cells for the same stack power, hence a higher volumetric power density (kW/L) and lower cost per kW than the original cross-flow cell design. A full SOFC system Simulink model was developed and calibrated with testing data from a fuel cell stack and BOP (balance of plant) components. The simulation results from the calibrated model showed an acceptable match with the experimental data. A structural analysis conducted for various load scenarios indicated no high stress areas for all spatial directions. Major electrical system components were acquired, built and successfully tested. System sensors were verified and validated against controls. Safety checks, a diagnostic check, PID tuning, and control software commissioning tasks were also conducted. The power electronics prototype was delivered and trial testing completed. Balance of Plant component testing and simulation work was conducted to characterize Reformer-Heat Exchanger heat transfer and backpressure and reformer catalyst methane conversion and product selectivity. Simulations were conducted to design the Anode and Cathode fluid passages and size the air-air and fuel-fuel heat exchangers. A Burner operation map was created from test data and the Anode Gas Recirculation blower was tested to evaluate its durability. The SOFC system used a horizontal style design where components sit directly on a casting with a direct connection to the skid. This design has efficient packaging and a small footprint with approximate dimensions of 750 mm x 700 mm x 1700 mm. An SOFC system was built and successfully tested at the Malta, NY facility The system for over 500 hours under load of which over 300 hours was at full load of 20 kW.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1979

Machine processing of remotely sensed data; Proceedings of the Fifth Annual Symposium, Purdue University, West Lafayette, Ind., June 27-29, 1979

Papers are presented on techniques and applications for the machine processing of remotely sensed data. Specific topics include the Landsat-D mission and thematic mapper, data preprocessing to account for atmospheric and solar illumination effects, sampling in crop area estimation, the LACIE program, the assessment of revegetation on surface mine land using color infrared aerial photography, the identification of surface-disturbed features through a nonparametric analysis of Landsat MSS data, the extraction of soil data in vegetated areas, and the transfer of remote sensing computer technology to developing nations. Attention is also given to the classification of multispectral remote sensing data using context, the use of guided clustering techniques for Landsat data analysis in forest land cover mapping, crop classification using an interactive color display, and future trends in image processing software and hardware.

Tendam, I. M.↗
NASA NTRS1987

Determination of surface shear stress with the naphthalene sublimation technique

Aeolian entrainment and transport are functions of surface shear stress and particle characteristics. Measuring surface shear stress is difficult, however, where logarithmic wind profiles are not found, such as regions around large roughness elements. An outline of a method whereby shear stress can be mapped on the surface around an object is presented. The technique involves the sublimation of naphthalene (C10H8) which is a function of surface shear stress and surface temperature. This technique is based on the assumption that the transfer of momentum, heat and mass are analogous (Reynolds analogy). If the Reynolds analogy can be shown to be correct for a given situation, then knowledge of the diffusion of one property allows the determination of the others. The analytical framework and data acquisition for the method are described. The technique was tested in the Planetary Geology Wind Tunnel. Results show that the naphthalene sublimation technique is a reasonably accurate method for determining shear stress, particularly around objects where numerous point values are needed.

Lee, J. A.↗
NASA NTRS1994

Towards a Comprehensive Computational Simulation System for Turbomachinery

The objective of this work is to develop algorithms associated with a comprehensive computational simulation system for turbomachinery flow fields. This development is accomplished in a modular fashion. These modules includes grid generation, visualization, network, simulation, toolbox, and flow modules. An interactive grid generation module is customized to facilitate the grid generation process associated with complicated turbomachinery configurations. With its user-friendly graphical user interface, the user may interactively manipulate the default settings to obtain a quality grid within a fraction of time that is usually required for building a grid about the same geometry with a general-purpose grid generation code. Non-Uniform Rational B-Spline formulations are utilized in the algorithm to maintain geometry fidelity while redistributing grid points on the solid surfaces. Bezier curve formulation is used to allow interactive construction of inner boundaries. It is also utilized to allow interactive point distribution. Cascade surfaces are transformed from three-dimensional surfaces of revolution into two-dimensional parametric planes for easy manipulation. Such a transformation allows these manipulated plane grids to be mapped to surfaces of revolution by any generatrix definition. A sophisticated visualization module is developed to al-low visualization for both grid and flow solution, steady or unsteady. A network module is built to allow data transferring in the heterogeneous environment. A flow module is integrated into this system, using an existing turbomachinery flow code. A simulation module is developed to combine the network, flow, and visualization module to achieve near real-time flow simulation about turbomachinery geometries. A toolbox module is developed to support the overall task. A batch version of the grid generation module is developed to allow portability and has been extended to allow dynamic grid generation for pitch changing turbomachinery configurations. Various applications with different characteristics are presented to demonstrate the success of this system.

Shih, Ming-Hsin↗
NASA NTRS2010

NASA Tech Briefs, April 2010

Topics covered include: Active and Passive Hybrid Sensor; Quick-Response Thermal Actuator for Use as a Heat Switch; System for Hydrogen Sensing; Method for Detecting Perlite Compaction in Large Cryogenic Tanks; Using Thin-Film Thermometers as Heaters in Thermal Control Applications; Directional Spherical Cherenkov Detector; AlGaN Ultraviolet Detectors for Dual-Band UV Detection; K-Band Traveling-Wave Tube Amplifier; Simplified Load-Following Control for a Fuel Cell System; Modified Phase-meter for a Heterodyne Laser Interferometer; Loosely Coupled GPS-Aided Inertial Navigation System for Range Safety; Sideband-Separating, Millimeter-Wave Heterodyne Receiver; Coaxial Propellant Injectors With Faceplate Annulus Control; Adaptable Diffraction Gratings With Wavefront Transformation; Optimizing a Laser Process for Making Carbon Nanotubes; Thermogravimetric Analysis of Single-Wall Carbon Nanotubes; Robotic Arm Comprising Two Bending Segments; Magnetostrictive Brake; Low-Friction, Low-Profile, High-Moment Two-Axis Joint; Foil Gas Thrust Bearings for High-Speed Turbomachinery; Miniature Multi-Axis Mechanism for Hand Controllers; Digitally Enhanced Heterodyne Interferometry; Focusing Light Beams To Improve Atomic-Vapor Optical Buffers; Landmark Detection in Orbital Images Using Salience Histograms; Efficient Bit-to-Symbol Likelihood Mappings; Capacity Maximizing Constellations; Natural-Language Parser for PBEM; Policy Process Editor for P(sup 3)BM Software; A Quality System Database; Trajectory Optimization: OTIS 4; and Computer Software Configuration Item-Specific Flight Software Image Transfer Script Generator.

Source record↗
DOE OSTI2025

Integrated Methane Monitoring Platform Extension, Volume I: Final Technical Report

The IMMPE project, DE-FE0032284, was to enhance methane monitoring technologies and their applications across various natural gas asset classes. The scope included deploying advanced methane detection and monitoring technologies to identify and mitigate fugitive methane emissions, measuring emission rates, and assessing impacts. The findings included the successful mitigation of identified emissions and quantification of emission rates. A key outcome was the development of a comprehensive template and summary of recommendations for methane emissions monitoring, which is replicable for both upstream and downstream applications. Furthermore, the project emphasized the importance of education by providing training opportunities for technicians and regulators, thereby fostering awareness and promoting the adoption of cost-effective methane emissions monitoring and management techniques.

02 PETROLEUM↗
NASA NTRS2000

Mapping Environmental Contaminants at Ray Mine, AZ

Airborne Visible and InfraRed Imaging Spectrometer (AVIRIS) data was collected over Ray Mine as part of a demonstration project for the Environmental Protection Agency (EPA) through the Advanced Measurement Initiative (AMI). The overall goal of AMI is to accelerate adoption and application of advanced measurement technologies for cost effective environmental monitoring. The site was selected to demonstrate the benefit to EPA in using advanced remote sensing technologies for the detection of environmental contaminants due to the mineral extraction industry. The role of the Jet Propulsion Laboratory in this pilot study is to provide data as well as performing calibration, data analysis, and validation of the AVIRIS results. EPA is also interested in developing protocols that use commercial software to perform such work on other high priority EPA sites. Reflectance retrieval was performed using outputs generated by the MODTRAN radiative transfer model and field spectra collected for the purpose of calibration. We are presenting advanced applications of the ENVI software package using n-Dimensional Partial Unmixing to identify image-derived endmembers that best match target materials reference spectra from multiple spectral libraries. Upon identification of the image endmembers the Mixture Tuned Match Filter algorithm was applied to map the endmembers within each scene. Using this technique it was possible to map four different mineral classes that are associated with mine generated acid waste.

McCubbin, Ian↗
DOE OSTI2018

Enhancing the Visible-Light Absorption and Excited-State Properties of Cu(I) MLCT Excited States

A computationally inspired Cu(I) metal-to-ligand charge transfer (MLCT) chromophore, [Cu(sbmpep) 2 ] + (sbmpep = 2,9-di( sec -butyl)-3,8-dimethyl-4,7-di(phenylethynyl)-1,10-phenanthroline), was synthesized in seven total steps, prepared from either dichloro- or dibromophenanthroline precursors. Complete synthesis, structural characterization, and electrochemistry, in addition to static and dynamic photophysical properties of [Cu(sbmpep) 2 ] + , are observed on all relevant time scales. UV–Vis absorption spectroscopy revealed significant increases in oscillator strength along with a concomitant bathochromic shift in the MLCT absorption bands with respect to structurally related model complexes (ε = 16 500 M –1 cm –1 at 491 nm). Strong red photoluminescence (Φ = 2.7%, λ max = 687 nm) was determined from [Cu(sbmpep) 2 ] + , which featured an average excited-state lifetime of 1.4 μs in deaerated dichloromethane. Cyclic and differential pulse voltammetry revealed ~300 mV positive shifts in the measured one-electron reversible reduction and oxidation waves in relation to a Cu(I) model complex possessing identical structural elements without the π-conjugated 4,7-substituents. The excited-state redox potential of [Cu(sbmpep) 2 ] + was estimated to be -1.36 V, a notably powerful reductant for driving photoredox chemistry. The combination of conventional and ultrafast transient absorption and luminescence spectroscopy successfully map the excited-state dynamics of [Cu(sbmpep) 2 ] + from initial photoexcitation to the formation of the lowest-energy MLCT excited state and ultimately its relaxation to the ground state. This newly conceived molecule appears poised for photosensitization reactions involving energy and electron-transfer processes relevant to photochemical upconversion, photoredox catalysis, and solar fuels photochemistry.

14 SOLAR ENERGY↗
NASA NTRS2017

Interactive Visualization of High-Dimensional Petascale Ocean Data

We describe an application for interactive visualization of 5 petabytes of time-varying multivariate data from a high-resolution global ocean circulation model. The input data are 10311 hourly (ocean time) time steps of various 2D and 3D fields from a 22-billion point 1/48- degree “lat-lon cap” configuration of the MIT General Circulation Model (MITgcm). We map the global horizontal model domain onto our 128-screen (8x16) tiled display wall to produce a canonical tiling with approximately one MITgcm grid point per display pixel, and using this tiling we encode the entire time series for multiple native and computed scalar quantities at a collection of ocean depths. We reduce disk bandwidth requirements by converting the model’s floating point data to 16-bit fixed point values, and compressing those values with a lossless video encoder, which together allow synchronized playback at 24 time steps per second across all 128 displays. The application allows dynamic assignment of any two encoded tiles to any display, and has multiple interfaces for quickly specifying various orderly arrangements of tiles. All subsequent rendering is done on the fly, with run time control of colormaps, transfer functions, histogram equalization, and labeling. The two data streams on each screen can be rendered independently and combined in various ways, including blending, differencing, horizontal/ vertical wipes, and checkerboarding. The two data streams on any screen can optionally be displayed as a scatterplot in their joint attribute space. All scatterplots and map-view plots from the same x/y location and depth are linked so they all show the current brushable selection. Ocean scientists have used the system, and have found previously unidentified features in the data.

Interactive↗