SEARCH · Engineering Papers

Results for “system analysis module”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

All sources NASA NTRS DOE OSTI

NASA NTRS1988

The performance of trellis coded multilevel DPSK on a fading mobile satellite channel

The performance of trellis-coded multilevel differential phase-shift-keying (MDPSK) modulation over Rician and Rayleigh fading channels is discussed. For operation at L-band, this signalling technique leads to a more robust system than the coherent system with dual pilot tone calibration previously proposed for UHF. The results are obtained using a combination of analysis and simulation. The analysis shows that the design criterion for trellis codes to be operated on fading channels with interleaving/deinterleaving is no longer free Euclidean distance. The correct design criterion for optimizing bit error probability of trellis coded MDPSD over fading channels is presented along with examples illustrating its application.

Simon, Marvin K.↗

NASA NTRS1990

Polarization considerations for optical systems II; Proceedings of the Meeting, San Diego, CA, Aug. 9-11, 1989

Various papers on polarization considerations for optical systems are presented. Individual topics addressed include: use of polarization methods in earth resources investigation, measurements of polarization scattering in the vacuum UV, the Space Shuttle as a polarization observation platform, analysis of spatial pseudodepolarizers in imaging systems, analysis of polarization effects in optical systems, and a low-polarization solar vector magnetograph. Consideration is given to polarization effects on astronomical spatial interferometry, measurement of the instrumental polarization of a high-resolution UV spectrometer, and the use of KD(asterisk)P modulators for polarization measurements of the sun.

Chipman, Russell A.↗

NASA NTRS1993

Optical communications and a comparison of optical technologies for a high data rate return link from Mars

The important principles of direct- and heterodyne-detection optical free-space communications are reviewed. Signal-to-noise-ratio (SNR) and bit-error-rate (BER) expressions are derived for both the direct-detection and heterodyne-detection optical receivers. For the heterodyne system, performance degradation resulting from received-signal and local oscillator-beam misalignment and laser phase noise is analyzed. Determination of interfering background power from local and extended background sources is discussed. The BER performance of direct- and heterodyne-detection optical links in the presence of Rayleigh-distributed random pointing and tracking errors is described. Finally, several optical systems employing Nd:YAG, GaAs, and CO2 laser sources are evaluated and compared to assess their feasibility in providing high-data-rate (10- to 1000-Mbps) Mars-to-Earth communications. It is shown that the root mean square (rms) pointing and tracking accuracy is a critical factor in defining the system transmitting laser-power requirements and telescope size and that, for a given rms error, there is an optimum telescope aperture size that minimizes the required power. The results of the analysis conducted indicate that, barring the achievement of extremely small rms pointing and tracking errors (less than 0.2 microrad), the two most promising types of optical systems are those that use an Nd:YAG laser (lambda = 1.064 microns) and high-order pulse position modulator (PPM) and direct detection, and those that use a CO2 laser (lambda = 10.6 microns) and phase shifting keying homodyne modulation and coherent detection. For example, for a PPM order of M = 64 and an rms pointing accuracy of 0.4 microrad, an Nd:YAG system can be used to implement a 100-Mbps Mars link with a 40-cm transmitting telescope, a 20-W laser, and a 10-m receiving photon bucket. Under the same conditions, a CO2 system would require 3-m transmitting and receiving telescopes and a 32-W laser to implement such a link. Other types of optical systems, such as a semiconductor laser systems, are impractical in the presence of large rms pointing errors because of the high power requirements of the 100-Mbps Mars link, even when optimal-size telescopes are used.

Spence, Rodney L.↗

NASA NTRS1992

Study of pseudo noise CW diode laser for ranging applications

A new Pseudo Random Noise (PN) modulated CW diode laser radar system is being developed for real time ranging of targets at both close and large distances (greater than 10 KM) to satisy a wide range of applications: from robotics to future space applications. Results from computer modeling and statistical analysis, along with some preliminary data obtained from a prototype system, are presented. The received signal is averaged for a short time to recover the target response function. It is found that even with uncooperative targets, based on the design parameters used (200-mW laser and 20-cm receiver), accurate ranging is possible up to about 15 KM, beyond which signal to noise ratio (SNR) becomes too small for real time analog detection.

Lee, Hyo S.↗

NASA NTRS1999

The Low-Mass X-Ray Binary X1832-330 in the Globular Cluster NGC 6652: A Serendipitous ASCA Observation

The Low Mass X-ray Binary (LMXB) X1832-330 in NGC 6652 is one of about 10 bright X-ray sources to have been discovered in Globular Clusters. We report on a serendipitous ASCA observation of this Globular Cluster LMXB, during which a Type I burst was detected and the persistent, non-burst emission of the source was at its brightest level recorded to date. No orbital modulation was detected, which argues against a high inclination for the X1832-330 system. The spectrum of the persistent emission can be fit with a power law plus a partial covering absorber, although other models are not ruled out. Our time-resolved spectral analysis through the burst shows, for the first time, clear evidence for spectral cooling from kT = 2.4 +/- 0.6 keV to kT = 1.0 +/- 0.1 keV during the decay. The measured peak flux during the burst is approximately 10% of the Eddington luminosity for a 1.4 Solar Mass neutron star. These are characteristic of a Type I burst, in the context of the relatively low quiescent luminosity of X1832-330.

Mukai, Koji↗

NASA NTRS2003

Microgravity Emissions Laboratory Testing of the Light Microscopy Module Control Box Fan

The Microgravity Emissions Laboratory (MEL) was developed at the NASA Glenn Research Center for the characterization, simulation, and verification of the International Space Station (ISS) microgravity environment. This Glenn lab was developed in support of the Fluids and Combustion Facility (FCF). The MEL is a six-degrees-of-freedom inertial measurement system that can characterize the inertial response forces (emissions) of components, subrack payloads, or rack-level payloads down to 10 7g. The inertial force output data generated from the steady-state or transient operations of the test article are used with finite element analysis, statistical energy analysis, and other analysis tools to predict the on-orbit environment at specific science or rack interface locations. Customers of the MEL have used benefits in isolation performance testing in defining available attenuation during the engineering hardware design phase of their experiment s development. The Light Microscopy Module (LMM) Control Box (LCB) fan was tested in the MEL in June and July of 2002. The LMM is planned as a remotely controllable on-orbit microscope subrack facility that will be accommodated in an FCF Fluids Integrated Rack on the ISS. The disturbances measured in the MEL test resulted from operation of the air-circulation fan within the LCB. The objectives of the testing were (1) to identify an isolator to be added to the LCB fan assembly to reduce fan-speed harmonics and (2) to identify the fan-disturbance forcing functions for use in rack-response analysis of the LMM and Fluids Integrated Rack facility. This report describes the MEL, the testing process, and the results from ground-based MEL LCB fan testing.

McNelis, Anne M.↗

NASA NTRS2009

Port-O-Sim Object Simulation Application

Port-O-Sim is a software application that supports engineering modeling and simulation of launch-range systems and subsystems, as well as the vehicles that operate on them. It is flexible, distributed, object-oriented, and realtime. A scripting language is used to configure an array of simulation objects and link them together. The script is contained in a text file, but executed and controlled using a graphical user interface. A set of modules is defined, each with input variables, output variables, and settings. These engineering models can be either linked to each other or run as standalone. The settings can be modified during execution. Since 2001, this application has been used for pre-mission failure mode training for many Range Safety Scenarios. It contains range asset link analysis, develops look-angle data, supports sky-screen site selection, drives GPS (Global Positioning System) and IMU (Inertial Measurement Unit) simulators, and can support conceptual design efforts for multiple flight programs with its capacity for rapid six-degrees-of-freedom model development. Due to the assembly of various object types into one application, the application is applicable across a wide variety of launch range problem domains.

Lanzi, Raymond J.↗

NASA NTRS2011

Sloshing in Liquid Hydrogen and LOX Propellant Tanks After Main Engine Cut-off

NASA Marshall Space Flight Center is designing and developing the Main Propulsion System (MPS) for Ares launch vehicles. The objective of this study is to calculate the sloshing forces and moments in the LH2 and LO2 propellant tanks using a CFD/VOF analysis under realistic flight conditions. Propellant sloshing in the liquid hydrogen (LH2) and the liquid oxygen (LO2) propellant tanks after Main Engine Cut Off (MECO) was modeled using the Volume of Fluid (VOF) module of the computational fluid dynamics code, CFD-ACE+. The present simulation shows that there are substantial sloshing side forces acting on the LH2 tank during the deceleration of the vehicle after MECO. The LH2 tank features a side wall drain pipe. The side loads result from the residual propellant mass motion in the LH2 tank which is initiated by the stop of flow into the drain pipe at MECO. The simulations show that radial force on the LH2 tank wall is less than 50 lbf and the radial moment calculated based up the center of gravity of the vehicle is predicted to be as high as 300 lbf-ft. The LO2 tank features a bottom dome drain system and is equipped with sloshing baffles. The remaining LO2 in the tank slowly forms a liquid column along the centerline of tank under the zero gravity environments. The radial force on the LO2 tank wall is predicted less than 100 lbf. The radial moment calculated based on the center of gravity of the vehicle is predicted as high as 4500 lbf-ft just before MECO and dropped down to near zero after propellant draining stopped completely.

Kim, Sura↗

NASA NTRS1971

Communication system modeling

This report presents the results of work on communications systems modeling and covers three different areas of modeling. The first of these deals with the modeling of signals in communication systems in the frequency domain and the calculation of spectra for various modulations. These techniques are applied in determining the frequency spectra produced by a unified carrier system, the down-link portion of the Command and Communications System (CCS). The second modeling area covers the modeling of portions of a communication system on a block basis. A detailed analysis and modeling effort based on control theory is presented along with its application to modeling of the automatic frequency control system of an FM transmitter. A third topic discussed is a method for approximate modeling of stiff systems using state variable techniques.

Holland, L. D.↗

NASA NTRS1975

The realization of arithmetic processors for delta modulation encoded signals

The design and realization of digital devices which add or multiply delta modulation (DM) encoded signals are presented. These systems operate directly on the DM bit stream. It is shown that the devices can be constructed using standard digital hardware and that the hardware complexity needed to add or multiply the two DM encoded signals is equivalent to that needed for pulse code modulation (PCM) signals. Experimental results are presented showing the operation of these systems. The results obtained by adding or multiplying DM encoded signals are compared with those obtained using PCM encoded signals on the basis of signal-to-noise ratio (SNR). A spectral-analysis technique applicable to a DM encoded signal is developed to obtain SNR curves.

Locicero, J. L.↗

NASA NTRS1976

Orbital precession in Hercules X-1

It is noted that the 35-day X-ray high-low cycle of Her X-1 could be explained in terms of periodic obscuration of the source by a tilted and precessing 'slaved' accretion disk, which would require precession of the mass-shedding star and, consequently, a precessing binary orbit. Four months of Uhuru data obtained in 1972 are analyzed to determine whether the orbital precession can be detected as a Doppler modulation in the arrival times of the 1.24-sec X-ray pulsations. The precession geometry is examined, the test for precession is outlined, and a marginally significant indication of orbital precession in the Hz Her/Her X-1 system is obtained. Possible biases in the analysis are evaluated, and the spin-axis misalignment of HZ Her is estimated from the measured tilt of the orbit.

Deeter, J. E.↗

NASA NTRS1980

Finite element for rotor/stator interactive forces in general engine dynamic simulation. Part 1: Development of bearing damper element

A general purpose squeeze-film damper interactive force element was developed, coded into a software package (module) and debugged. This software package was applied to nonliner dynamic analyses of some simple rotor systems. Results for pressure distributions show that the long bearing (end sealed) is a stronger bearing as compared to the short bearing as expected. Results of the nonlinear dynamic analysis, using a four degree of freedom simulation model, showed that the orbit of the rotating shaft increases nonlinearity to fill the bearing clearance as the unbalanced weight increases.

Adams, M. L.↗

NASA NTRS1984

Interactive systems design and synthesis of future spacecraft concepts

An interactive systems design and synthesis is performed on future spacecraft concepts using the Interactive Design and Evaluation of Advanced spacecraft (IDEAS) computer-aided design and analysis system. The capabilities and advantages of the systems-oriented interactive computer-aided design and analysis system are described. The synthesis of both large antenna and space station concepts, and space station evolutionary growth is demonstrated. The IDEAS program provides the user with both an interactive graphics and an interactive computing capability which consists of over 40 multidisciplinary synthesis and analysis modules. Thus, the user can create, analyze and conduct parametric studies and modify Earth-orbiting spacecraft designs (space stations, large antennas or platforms, and technologically advanced spacecraft) at an interactive terminal with relative ease. The IDEAS approach is useful during the conceptual design phase of advanced space missions when a multiplicity of parameters and concepts must be analyzed and evaluated in a cost-effective and timely manner.

Wright, R. L.↗

NASA NTRS1983

Growth, characterization, and properties of metastable and modulated semiconductor structures - Prospects for future studies

The general field of preparation and study of metastable and modulated semiconductor structures has progressed rapidly in recent years. This short overview offers an assessment of the progress and current understanding in the areas of fabrication, characterization, and utilization of these new material systems. The discussion includes the more prominent growth techniques, theoretical and experimental analysis of growth kinetics, and an overview of structural, chemical, electronic, and optical characterization. The probable application of these structures for the technological development of new device structures and concepts is considered. The discussion particularly emphasizes the prospects for future studies in view of the specific current understanding.

Grunthaner, F. J.↗

NASA NTRS1987

Verification of FANTASTIC integrated code

FANTASTIC is an acronym for Failure Analysis Nonlinear Thermal and Structural Integrated Code. This program was developed by Failure Analysis Associates, Palo Alto, Calif., for MSFC to improve the accuracy of solid rocket motor nozzle analysis. FANTASTIC has three modules: FACT - thermochemical analysis; FAHT - heat transfer analysis; and FAST - structural analysis. All modules have keywords for data input. Work is in progress for the verification of the FAHT module, which is done by using data for various problems with known solutions as inputs to the FAHT module. The information obtained is used to identify problem areas of the code and passed on to the developer for debugging purposes. Failure Analysis Associates have revised the first version of the FANTASTIC code and a new improved version has been released to the Thermal Systems Branch.

Chauhan, Rajinder Singh↗

NASA NTRS1997

Microgravity Environment Description Handbook

The Microgravity Measurement and Analysis Project (MMAP) at the NASA Lewis Research Center (LeRC) manages the Space Acceleration Measurement System (SAMS) and the Orbital Acceleration Research Experiment (OARE) instruments to measure the microgravity environment on orbiting space laboratories. These laboratories include the Spacelab payloads on the shuttle, the SPACEHAB module on the shuttle, the middeck area of the shuttle, and Russia's Mir space station. Experiments are performed in these laboratories to investigate scientific principles in the near-absence of gravity. The microgravity environment desired for most experiments would have zero acceleration across all frequency bands or a true weightless condition. This is not possible due to the nature of spaceflight where there are numerous factors which introduce accelerations to the environment. This handbook presents an overview of the major microgravity environment disturbances of these laboratories. These disturbances are characterized by their source (where known), their magnitude, frequency and duration, and their effect on the microgravity environment. Each disturbance is characterized on a single page for ease in understanding the effect of a particular disturbance. The handbook also contains a brief description of each laboratory.

DeLombard, Richard↗

NASA NTRS1991

SEAPAK user's guide, version 2.0. Volume 1: System description

The SEAPAK is a user interactive satellite data analysis package that was developed for the processing and interpretation of Nimbus-7/Coastal Zone Color Scanner (CZCS) and the NOAA Advanced Very High Resolution Radiometer (AVHRR) data. Significant revisions were made to version 1.0 of the guide, and the ancillary environmental data analysis module was expanded. The package continues to emphasize user friendliness and user interactive data analyses. Additionally, because the scientific goals of the ocean color research being conducted have shifted to large space and time scales, batch processing capabilities for both satellite and ancillary environmental data analyses were enhanced, thus allowing large quantities of data to be ingested and analyzed in background.

Mcclain, Charles R.↗

NASA NTRS1975

Large Space Telescope support systems module thermal control

In 1982, an unmanned three-meter class Cassegrainian telescopic system referred to as the Large Space Telescope (LST) will be placed in earth orbit by the Shuttle. The LST consists of a telescope system and surrounding support structure that is referred to as the support system module (SSM). This paper summarizes the thermal control subsystem for several candidate SSM designs. Major emphasis has been given to the LST/SSM design concept that includes a thermally isolated aft cylinder compartment that contains subsystem components. Requirements, interfaces and thermal math modeling methods are presented. Analysis results demonstrate that a cold-biased thermal design using electrical heaters is promising.

Chapter, J. J.↗