Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “support effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Critical target and dose and dose-rate responses for the induction of chromosomal instability by ionizing radiation

To investigate the critical target, dose response and dose-rate response for the induction of chromosomal instability by ionizing radiation, bromodeoxyuridine (BrdU)-substituted and unsubstituted GM10115 cells were exposed to a range of doses (0.1-10 Gy) and different dose rates (0.092-17.45 Gy min(-1)). The status of chromosomal stability was determined by fluorescence in situ hybridization approximately 20 generations after irradiation in clonal populations derived from single progenitor cells surviving acute exposure. Overall, nearly 700 individual clones representing over 140,000 metaphases were analyzed. In cells unsubstituted with BrdU, a dose response was found, where the probability of observing delayed chromosomal instability in any given clone was 3% per gray of X rays. For cells substituted with 25-66% BrdU, however, a dose response was observed only at low doses (<1.0 Gy); at higher doses (>1.0 Gy), the incidence of chromosomal instability leveled off. There was an increase in the frequency and complexity of chromosomal instability per unit dose compared to cells unsubstituted with BrdU. The frequency of chromosomal instability appeared to saturate around approximately 30%, an effect which occurred at much lower doses in the presence of BrdU. Changing the gamma-ray dose rate by a factor of 190 (0.092 to 17.45 Gy min(-1)) produced no significant differences in the frequency of chromosomal instability. The enhancement of chromosomal instability promoted by the presence of the BrdU argues that DNA comprises at least one of the critical targets important for the induction of this end point of genomic instability.

NASA Discipline Radiation Health↗

High performance interconnection between high data rate networks

The bridge/gateway system needed to interconnect a wide range of computer networks to support a wide range of user quality-of-service requirements is discussed. The bridge/gateway must handle a wide range of message types including synchronous and asynchronous traffic, large, bursty messages, short, self-contained messages, time critical messages, etc. It is shown that messages can be classified into three basic classes, synchronous and large and small asynchronous messages. The first two require call setup so that packet identification, buffer handling, etc. can be supported in the bridge/gateway. Identification enables resequences in packet size. The third class is for messages which do not require call setup. Resequencing hardware based to handle two types of resequencing problems is presented. The first is for a virtual parallel circuit which can scramble channel bytes. The second system is effective in handling both synchronous and asynchronous traffic between networks with highly differing packet sizes and data rates. The two other major needs for the bridge/gateway are congestion and error control. A dynamic, lossless congestion control scheme which can easily support effective error correction is presented. Results indicate that the congestion control scheme provides close to optimal capacity under congested conditions. Under conditions where error may develop due to intervening networks which are not lossless, intermediate error recovery and correction takes 1/3 less time than equivalent end-to-end error correction under similar conditions.

Foudriat, E. C.↗

A hot-wire surface gage for skin friction and separation detection measurements

A heated-element, skin-friction gage employing a very low thermal conductivity support is described. It is shown that the effective dimension of the gage in the stream direction in only 0.06 mm, including the effects of heat conduction in the supporting material. Because of its small size, the calibration of the gage is independent of the kind of boundary-layer flow (whether laminar or turbulent) and is insensitive to pressure gradients. Construction tolerances can be maintained so that a single universal calibration can be applied. Multiple gages, sufficiently closely spaced so as to interfere with each other, are shown to provide accurate determinations of the locations of the points of boundary-layer separation and reattachment.

Rubesin, M. W.↗

Flush-mounted hot-wire gage for skin friction and separation detection measurements

A heated-element skin-friction gage employing a very low thermal-conductivity support is described. It is shown that the effective dimension of the gage in the stream direction is only 0.06 mm, including the effects of heat conduction in the supporting material. Because of its small size, the calibration of the gage is independent of the kind of boundary-layer flow (whether laminar or turbulent) and is insensitive to pressure gradients. Construction tolerances can be maintained so that a single universal calibration can be applied. Multiple gages, sufficiently closely spaced so as to interfere with each other, are shown to provide accurate determinations of the location of the points of boundary-layer separation and reattachment.

Rubesin, M. W.↗

Collaboration technology and space science

A summary of available collaboration technologies and their applications to space science is presented as well as investigations into remote coaching paradigms and the role of a specific collaboration tool for distributed task coordination in supporting such teleoperations. The applicability and effectiveness of different communication media and tools in supporting remote coaching are investigated. One investigation concerns a distributed check-list, a computer-based tool that allows a group of people, e.g., onboard crew, ground based investigator, and mission control, to synchronize their actions while providing full flexibility for the flight crew to set the pace and remain on their operational schedule. This autonomy is shown to contribute to morale and productivity.

Leiner, Barry M.↗

Evidence for yellow light suppression of lettuce growth

Researchers studying plant growth under different lamp types often attribute differences in growth to a blue light response. Lettuce plants were grown in six blue light treatments comprising five blue light fractions (0, 2, 6% from high-pressure sodium [HPS] lamps and 6, 12, 26% from metal halide [MH] lamps). Lettuce chlorophyll concentration, dry mass, leaf area and specific leaf area under the HPS and MH 6% blue were significantly different, suggesting wavelengths other than blue and red affected plant growth. Results were reproducible in two replicate studies at each of two photosynthetic photon fluxes, 200 and 500 mumol m-2 s-1. We graphed the data against absolute blue light, phytochrome photoequilibrium, phototropic blue, UV, red:far red, blue:red, blue: far red and 'yellow' light fraction. Only the 'yellow' wavelength range (580-600 nm) explained the differences between the two lamp types.

Non-NASA Center↗

Diethylenetriamine-functionalized graphene oxide: Insights into ion adsorption and applications in rare earth element separation

The growing demand for critical minerals and materials requires atom- and energy-efficient, selective separations to overcome the challenges posed by the similar chemical and physical properties of the rare earth elements (REEs) and their low concentrations in unconventional domestic feedstocks. Here, in this study, we developed diethylenetriamine-functionalized graphene oxide (DETA-GO) as a membrane material for REE adsorption and separation. Synthesis conditions were optimized to maximize nitrogen incorporation while also preserving GO dispersibility for facile membrane fabrication. We investigated the mechanism of amine functionalization, the nitrogen-bonding configurations, the organization of the interlayer transport channels, and the resulting effects on ion and water transport for REE separations. Neat-GO and DETA-GO multilayer laminate membranes were fabricated by vacuum filtration onto polymer supports. To investigate the effects of amine functionalization, the membranes were characterized using scanning electron microscopy, Raman, Fourier transform infrared, and X-ray photoelectron spectroscopy, as well as grazing-incidence X-ray diffraction measurements. Ion permeation experiments with representative lanthanum (La 3+ ) and ytterbium (Yb 3+ ) solutions revealed enhanced ion adsorption and water transport through DETA-GO membranes compared to neat-GO. The strong affinity of the membranes for multivalent REEs was also validated with conductivity and inductively coupled plasma mass spectrometry measurements. Atomistic insight into the role of amine functionalization in modulating nanochannel architecture and long-term stability, optimizing adsorption sites, and regulating REE and water transport was obtained using classical molecular dynamics simulations. Collectively, our joint experimental and theoretical study demonstrates the potential of DETA-GO membranes for selective REE separations, offering insights into ion-binding mechanisms, water-transport properties, and nanochannel optimization for the recovery of critical materials from aqueous feedstocks.

Adsorbent↗

Hydrogen activation by rhodium under the cover of a copper oxide thin film

Here, the activation of reactants by catalytically active metal sites at metal-oxide interfaces is important for understanding the effect of metal-support interactions on nanoparticle catalysts and for tuning activity and selectivity. Using a combined experimental and theoretical approach, we studied the activation of H 2 and the effect of CO poisoning on isolated Rh atoms completely or partially covered by a copper oxide (Cu 2 O) thin film. Temperature-programmed desorption (TPD) experiments conducted in ultra-high vacuum (UHV) show that neither a partially nor a fully oxidized Cu 2 O layer grown on a Rh/Cu(111) single-atom alloy can activate hydrogen in UHV. However, in situ ambient pressure X-ray photoelectron spectroscopy (AP-XPS) experiments performed at elevated H 2 pressures reveal that Rh significantly accelerates the reduction of these Cu 2 O thin films by hydrogen. Remarkably, the fastest reduction rate is observed for the fully oxidized sample with all Rh sites covered by Cu 2 O. Both TPD and AP-XPS data demonstrate that these covered Rh sites are inaccessible to CO, indicating that Rh under Cu 2 O is active for H 2 dissociation but cannot be poisoned by CO. In contrast, an incomplete oxide film leaves some of the Rh sites exposed and accessible to CO, and hence prone to CO poisoning. Density functional theory calculations demonstrate that unlike many reactions in which hydrogen activation is rate limiting, the rate-determining step in the dissociation of H 2 on thin-film Cu 2 O with Rh underneath is the adsorption of H 2 on the buried Rh site, and once adsorbed, the dissociation of H 2 is barrierless. These calculations also explain why H 2 can only be activated at higher pressures. Together, these results highlight how different the reactivity of atomically dispersed Rh in Cu can be depending on its accessibility through the oxide layer, providing a way to engineer Rh sites that are active for hydrogen activation but resilient to CO poisoning.

36 MATERIALS SCIENCE↗

Advanced Group Support Systems and Facilities

The document contains the proceedings of the Workshop on Advanced Group Support Systems and Facilities held at NASA Langley Research Center, Hampton, Virginia, July 19-20, 1999. The workshop was jointly sponsored by the University of Virginia Center for Advanced Computational Technology and NASA. Workshop attendees came from NASA, other government agencies, industry, and universities. The objectives of the workshop were to assess the status of advanced group support systems and to identify the potential of these systems for use in future collaborative distributed design and synthesis environments. The presentations covered the current status and effectiveness of different group support systems.

Noor, Ahmed K.↗

Morphological responses of wheat to changes in phytochrome photoequilibrium

Wheat plants (Triticum aestivum L.) were grown at the same photosynthetic photon flux (PPF), 200 micromoles per square meter per second, but with phytochrome photoequilibrium (phi) values of 0.81, 0.55, and 0.33. Plants grown at phi values of 0.55 and 0.33 tillered 43 and 56%, less compared with plants grown at phi of 0.81. Main culm development (Haun stage) was slightly more advanced at lower values of phi, and leaf sheaths, but not leaf lamina, were longer at lower phi. Dry-mass accumulation was not affected by different levels of phi. Three levels of PPF (100, 200, and 400 micromoles per square meter per second) and two lamp types, metal halide and high pressure sodium, were also tested. Higher levels of PPF resulted in more dry mass, more tillering, and a more advanced Haun stage. There was no difference in plant dry mass or development under metal halide versus high pressure sodium lamps, except for total leaf length, which was greater under high pressure sodium lamps (49.5 versus 44.9 centimeters, P < 0.01).

Non-NASA Center↗

Hydroxyls on CeO 2 Support Promoting CuO/CeO 2 Catalyst for Efficient CO Oxidation and NO Reduction by CO

Transition metal catalysts, such as copper oxide, are more attractive alternatives to noble metal catalysts for emission control due to their higher abundance, lower cost, and excellent catalytic activity. Here, in this study, we report the preparation and application of a novel CuO/CeO 2 catalyst using a hydroxyl-rich Ce(OH) x support for CO oxidation and NO reduction by CO. Compared to the catalyst prepared from a regular CeO 2 support, the new CuO/CeO 2 catalyst prepared from the OH-rich Ce(OH) x (CuO/CeO 2 –OH) showed significantly higher catalytic activity under different testing conditions. The effect of OH species in the CeO 2 support on the catalytic performance and physicochemical properties of the CuO/CeO 2 catalyst was characterized in detail. It is demonstrated that the abundant OH species enhanced the CuO x dispersion on CeO 2 , increased the CuO x –CeO 2 interfaces and surface defects, promoted the oxygen activation and mobility, and boosted the NO adsorption and dissociation on CuO/CeO 2 –OH, thus contributing to its superior catalytic activity for both CO oxidation and NO reduction by CO. These results suggest that the OH-rich Ce(OH) x is a superior support for the preparation of highly efficient metal catalysts for different applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Intrinsic Thermal Hall Effect in Mott Insulators

Here, in light of recent experimental data indicating a substantial thermal Hall effect in square lattice antiferromagnetic Mott insulators, we investigate whether a simple Mott insulator can sustain a finite thermal Hall effect. We verify that the answer is “no” if one performs calculations within a spin-only low-energy effective spin model with noninteracting magnons. However, by performing determinant quantum Monte Carlo simulations, we show the single-band 𝑡−𝑡′−𝑈 Hubbard model coupled to an orbital magnetic field does support a finite thermal Hall effect when 𝑡′ ≠0 and 𝐵 ≠0 in the Mott insulating phase. We argue that the (carrier agnostic) necessary conditions for observing a finite thermal Hall effect are time-reversal and particle-hole symmetry breaking. By considering magnon-magnon scattering using a semiclassical Boltzmann analysis, we illustrate a physical mechanism by which finite transverse thermal conductivity may arise, consistent with our symmetry argument and numerical results. Our results indicate that square and triangular lattices with SU(2) symmetry can support a finite thermal Hall effect and call for a critical reexamination of thermal Hall effect data in insulating magnets, as the magnon contribution should not be excluded a priori .

Mott insulators↗

Structural and optical properties for typical solid mirror shapes

A method is developed to determine the weight, center of gravity, areal properties, and mass inertial properties for typical mirrors. A number of support conditions were considered to examine optical surface deflections, surface quality, and fundamental natural frequency for single- and double-arch mirror shapes. Structural performance estimates were made with the NASTRAN program, and optical performances were evaluated with the FRINGE program, using an SXA 40-in mirror. To show the behavior of element types from the NASTRAN program, finite element validity and sensitivity studies were performed in optical model applications. Material parameters, contoured back shapes, and support locations are shown to have significant effects on structural and optical performances. Optimal support locations and support points are given. Fundamental natural frequencies for some shapes are found with the closed-form solution. The plate models results may not be acceptable for determining real mirror optical performances.

Cho, Myung K.↗

Design and performance/measurement simulation studies for a ER-2 sunphotometer

Work and results, including developed software, obtained under this grant (NAG 2-620) have been reported in various progress reports, an M.S. Thesis, and software programs. The purpose of this final report is simply to provide a documented listing of what has already been reported. This includes the following: (1) Conceptual Design and Simulation of a Spectral Sunphotometer for the ER-2 Aircraft; (2) Continued Simulation and Design Studies for an ER-2 Sunphotometer; and (3) Simulation and Performance Studies of a Spectra Sunphotometer for the ER-2 Aircraft. Also, software and computational results for modeling airmass and diffuse light effects due to aerosols were provided in support of NASA ARC research on the effects of aerosols resulting from the Pinatubo volcanic eruptions. The references for these articles are as follows: (1) Post Pinatubo Optical Depth Spectra vs. Latitude and Vortex Structure; and (2) Pinatubo and Pre-Pinatubo Optical-Depth Spectra -- Mauna Loa Measurements, Comparisons, Inferred Particle Size Distributions, Radiative Effects, and Relationships to Lidar Data.

Reagan, J. A.↗

Weyl semimetal in the rare-earth hexaboride family supporting a pseudonodal surface and a giant anomalous Hall effect

Rare-earth hexaborides offer a rich tapestry for exploring the interplay of topological orders, magnetism, and electron-correlation effects associated with protected quantum phenomena. Using first-principles modeling, we identify in cerium hexaboride (CeB 6 ) a topological state that harbors a pseudonodal surface (PNS) along with double-Weyl fermions. An analysis of the electronic states in the vicinity of the Fermi level reveals the presence of M z -mirror-symmetry-protected band crossings that involve itinerant (d) and localized (f) states of Ce. These band crossings are found to remain nearly gapless as one goes away from the mirror plane, driving the formation of PNS states. We also demonstrate the presence of coexisting double-Weyl fermions with chiral charges of ±2 on the C 4z rotational axis. By analyzing the Berry curvature field associated with the topological states, we predict that CeB 6 supports a giant anomalous Hall conductivity of -1840Ω -1 cm -1 in the slightly electron-doped regime, which would be larger than the values reported to date in magnetic Weyl semimetals. Our study thus indicates that CeB 6 , which combines ferromagnetic order with topological physics in a heavy-fermion matrix, would provide a promising playground for investigating topological magnetic states with giant anomalous Hall responses.

36 MATERIALS SCIENCE↗

Analysis of Post-Support and Wind-Tunnel Wall Interference on Flow Field About Subsonic High-Lift High-Speed Research Configuration

The present study was performed to determine how significant the interference effects of the wind-tunnel model support system and tunnel walls can be for a high-speed configuration during takeoff and landing conditions. A 5-percent scale model of the Technology Concept Airplane was recently tested in the Langley 14- by 22-Foot Sub-sonic Tunnel. The model was numerically modeled with and without the support and tunnel walls and compared with experimental data. Detailed analysis of the flow provided additional insight concerning what effects the post support and tunnel walls had on the flow field. This study revealed that although the overall forces and moments could be experimentally accounted for, the detailed flow features, such as the surface pressure distributions, could not be accurately simulated without including the post support in the computations.

Lessard, Wendy B.↗

Effects of elevated atmospheric carbon dioxide concentrations on water and acid requirements of soybeans grown in a recirculating hydroponic system

Establishing mass budgets of various crop needs, i.e. water and nutrients, in different environments is essential for the Controlled Ecological Life Support System (CELSS). The effects of CO2 (500 and 1000 umol mol (exp -1)) on water and acid use (for pH control) by soybeans in a recirculating hydroponic system were examined. Plants of cvs. McCall and Pixie were grown for 90 days using the nutrient film technique (NFT) and a nitrate based nutrient solution. System acid use for both CO2 levels peaked near 4 weeks during a phase of rapid vegetative growth, but acid use decreased more rapidly under 500 compared to 1000 umol mol (exp GR) CO2. Total system water use by 500 and 1000 umol mol (exp -1) plants was similar, leaving off at 5 weeks and declining as plants senesced (ca. 9 weeks). However, single leaf transpiration rates were consistently lower at 1000 umol mol (exp -1). The data suggest that high CO2 concentrations increase system acid (and nutrient) use because of increased vegetative growth, which in turn negates the benefit of reduced water use (lower transpiration rates) per unit leaf area.

Mackowiak, C. L.↗