Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “separator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

New diagnostic technique for the study of turbulent boundary-layer separation

Description of a diagnostic technique for determining the unsteady character of turbulent boundary-layer separation. The technique uses thin platinum films mounted flush with the model surface. Voltages from these films provide measurements related to the flow character above the film. For illustration, results obtained by this technique are presented for the interaction of a hypersonic shock wave and a turbulent boundary layer, with and without separation.

Horstman, C. C.↗
NASA NTRS1974

Aerodynamic results of wind tunnel separation tests on a 0.01-scale model (32-OTS) space shuttle integrated vehicle in the AEDC-VKF-SWTA (IA57)

The integrated space shuttle vehicle was tested to determine proximity force and moment data for the orbiter/external tank and solid rocket booster (SRB) with and without separation rockets firing for both single and dual booster runs. Data were obtained at points t = 0 sec, t = 1.25 sec, and t = 2 sec on the nominal SRB separation trajectory.

Daileda, J. J.↗
NASA NTRS1974

Analytical study of subsonic turbulent boundary layer separation including viscous-inviscid interaction

The prediction of boundary layer deceleration and separation in regions of adverse pressure gradients are discussed as an unsolved problem of fundamental practical importance in aerodynamics. A three layered theoretical flow model of boundary layer separation including viscous-inviscid interaction was conceived for the case of subsonic two dimensional steady laminar flow.

Inger, G. R.↗
NASA NTRS1972

Separation negatives from Kodak film types SO-368 and SO-242

Two master resolution friskets were produced on Kodak film types SO-368 and SO-242. These target masters consisted of 21 density steps with three-bar resolution targets at five modulation levels within each step. The target masters were contact printed onto Kodak separation negative film, type 4131, using both a contact printing frame and enlarger as one method of exposure, and a Miller-Holzwarth contact printer as the other exposing device. Red, green, and blue Wratten filters were used to filter the exposing source. Tray processing was done with DK-50 developer diluted 1:2 at a temperature of 70 F. The resolution values were read for the SO-368 and SO-242 target masters, and the red, green, and blue separation negatives.

Weinstein, M. S.↗
NASA NTRS1975

Thermodynamics and phase separation of dense fully-ionized hydrogen-helium fluid mixtures

The free energy of a hydrogen-helium fluid mixture is evaluated for the temperatures and densities appropriate to the deep interior of a giant planet such as Jupiter. The electrons are assumed to be fully pressure-ionized and degenerate. In this regime, an appropriate first approximation to the ionic distribution functions can be found by assuming hard sphere interactions. Corrections to this approximation are incorporated by means of the perturbation theory of Anderson and Chandler. Approximations for the three-body interactions and the nonlinear response of the electron gas to the ions are included. It is predicted that a hydrogen-helium mixture, containing 10% by number of helium ions, separates into hydrogen-rich and helium-rich phases below about 8000 K, at the pressures relevant to Jupiter (4-40 Megabars). It is also predicted that the alloy occupies less volume per ion than the separated phases. The equations of state and other thermodynamic derivatives are tabulated. Implications of these results are discussed.

Stevenson, D. J.↗
NASA NTRS1975

Evaluation program for secondary spacecraft cells: Initial evaluation tests of Eagle-Picher Industries, Incorporated 6.0 ampere-hour, nickel-cadmium spacecraft cells for separator material evaluation

Several groups of nickel cadmium cells were tested for the durability of their separator materials. The cells were rated at 6.0 ampere-hours, and contained double ceramic seals. Two cells in each group were fitted with pressure gauge assemblies. Results are presented for various brands of separator materials.

Harkness, J. D.↗
NASA NTRS1975

Abort separation study of a shuttle orbiter and external tank at hypersonic speeds

The effects of several parameters on the relative motions of a space shuttle orbiter design and its external tank were determined during staging for the return-to-launch-site abort mode. The parameters included angle of attack, dynamic pressure, flight-path angle, pitch rate, elevon effectiveness and the use of thrust applied to the tank. The relative positions of each component were determined by a separation trajectory computer program which incorporated data obtained in wind-tunnel tests with the orbiter and tank in proximity. These tests were conducted at Mach 10.3 in a continuous-flow hypersonic tunnel. All separation cases were initiated at a constant Mach number of 10 with an assumed sideslip angle of 0 deg.

Bernot, P. T.↗
NASA NTRS1975

Experimental studies of flow separation and stalling on a two-dimensional airfoil at low speeds

Detailed measurements of flow fields associated with low-speed turbulent boundary layers were made for the 17% thick GA(W)-1 airfoil section at nominal angles of attack of 10 deg, 14 deg, and 18 deg, Reynolds number 2.2 x 10, and Mach number 0.13. The data include pressure and velocity surveys of the pre- and post-separated regions on the airfoil and the associated wake. The boundary layer characteristics including regions of separation on the airfoil are also presented.

Seetharam, H. C.↗
NASA NTRS1975

Permanent and separable aerospace tubing/ fitting evaluation program, volume 1

The tube fitting evaluation program was conducted to develop a standard overall test program including methods, procedures, and equipment as well as recommended test sequences for qualifying fitting/tubing assemblies. The program consisted of testing the MS flareless (separable) fitting and utilizing the results as baseline data from which all other fittings will be evaluated. Five separable designs and five permanent designs were tested in three sizes with two types of tubing materials. The basic design requirements were 4,000 psi operating pressure within the temperature range of minus 65 F to plus 450 F while also being compatible with 21-6-9 and titanium 3Al-2.5V tubing alloys.

Ursell, C. R.↗
NASA NTRS1975

Aerodynamic results of a separation effects test on a 0.01-scale model (52-OTS) of integrated SSV in the AEDC/VKF 40-by-40 inch supersonic wind tunnel A, volume 1

Experimental aerodynamic investigations were conducted, during the period July 18-19, 1974, in the AEDC/VKF Tunnel A facility on a 0.01-scale model (52-OTS) of the integrated space shuttle vehicle, including only one SRB. The purpose of the investigation was to obtain data for close-in proximity (SRB to orbiter/tank) effects with the orbiter/tank combination at relatively high alpha and beta attitudes, and with the SRB separation motors off. The AEDC Captive Trajectory System (CTS), which supported the SRB, was used in conjunction with the tunnel primary sector (supporting the orbiter/tank) to obtain grid type separation effects data. The one symmetrical SRB model was used interchangeably to obtain both right-hand and left-hand SRB data. Free-stream data were also obtained for the orbiter/tank and for the SRB. This data was used to provide baselines for proximity effects. The entire investigation was conducted at a free-stream Mach number of 4.5 with unit Reynolds number ranging from 4.0 to 6.5 million per foot.

Campbell, J. H., II↗
NASA NTRS1974

An evaluation of potentially useful separator materials for nickel-cadmium (Ni-Cd] satellite batteries

An evaluation intended to determine the potential suitability and probable efficacy of a group of separator materials for use in nickel-cadmium (Ni-Cd) satellite batteries was carried out. These results were obtained using test procedures established in an earlier evaluation of other separator materials, some of which were used in experimental battery cells subjected to simulated use conditions. The properties that appear to be most important are: high electrolyte absorptivity, good electrolyte retention, low specific resistivity, rapid wettability and low resistance to air permeation. Wicking characteristics and wet-out time seem to be more important with respect to the initial filling of the battery with the electrolyte.

Baker, H. A.↗
NASA NTRS1974

Primordial noble gases in separated meteoritic minerals. II

A stepwise heating technique was used to analyze eight silicate samples from the Orgueil carbonaceous chondrite for He, Ne, Ar, and Xe. Six samples, of which two were etched with NaOH, were density fractions. The other two samples were grain-size fractions separated according to their ability to form a colloid at pH 11.5. Results showed the LiCl separation procedure to be gentler than the NaOH procedure. All fractions were found to be deficient in cosmogenic neon. Above 950 C the fractions gave low 20Ne/22Ne ratios particularly in the low-density and noncolloidal fraction. Compared to the other fractions the fraction from 2.35 to 2.45 g/cu cm contained less Xe and released it more rapidly at low temperatures.

Herzog, G. F.↗
NASA NTRS1975

Starting vortex, separation bubbles and stall - A numerical study of laminar unsteady flow around an airfoil

The stalling characteristics of an airfoil in a laminar viscous incompressible fluid are investigated. The governing equations in terms of the vorticity and stream function are solved using an implicit finite-difference scheme and point successive relaxation procedure. The development of the impulsively started flow, the initial generation of circulation, and the behavior of the forces at large times are studied. Following the impulsive start, the lift is at first very large and then it rapidly drops. The subsequent growth of circulation and lift is associated with the starting vortex. After incipient separation, the lift increases owing to enlargement of the separation bubble and intensification of the flow rotation in it. The extension of this bubble beyond the trailing edge causes it to rupture and brings about the stalling characteristics of the airfoil. Subsequently, new bubbles are formed near the upper surface of the airfoil and are swept away. The behavior of the lift acting on the airfoil is explained in terms of the strength and sense of these bubbles.

Mehta, U. B.↗
NASA NTRS1975

Calculation of shock-separated turbulent boundary layers

Numerical solutions of the complete, time-averaged conservation equations using several eddy-viscosity models for the Reynolds shear stress to close the equations are compared with experimental measurements in a compressible, turbulent separated flow. An efficient time-splitting, explicit difference scheme was used to solve the two-dimensional conservation equations. The experiment used for comparison was a turbulent boundary layer that was separated by an incident shock wave in a Mach 2.93 flow with a unit Reynolds number of 5.7 x 10 to the seventh power m. Comparisons of predicted and experimental values of surface pressure, shear stress along the wall, and velocity profiles are shown. One of the tested eddy-viscosity models which allows the shear stress to be out of equilibrium with the mean flow produces substantially better agreement with the experimental measurements than the simpler models. A tool is thereby provided for inferring additional information about the flow, such as static pressures in the stream, which might not be directly obtainable from experiments.

Baldwin, B. S.↗
NASA NTRS1975

Simulation of turbulent transonic separated flow over an airfoil

A code developed for simulating high Reynolds number transonic flow fields of arbitrary configuration is described. This code, in conjunction with laboratory experiments, is used to devise and test turbulence transport models which may be suitable in the prediction of such flow fields, with particular emphasis on regions of flow separation. The solutions describe the flow field, including both the shock-induced and trailing-edge separation regions, in sufficient detail to provide the profile and friction drag.

Deiwert, G. S.↗
NASA NTRS1975

Electrophoretic separator for purifying biologicals

Mathematical expressions were developed to describe the interrelationships between operating requirements (capabilities), cell parameters, and system constraints in terms of design criteria definition. The mathematical model was programmed for computer solution. The model was exercised to identify performance-limiting characteristics, and analyses were conducted to predict operation in space of an experiment involving separation of four components. An engineering model of a flowing electrophoretic separator was constructed. The design is directed toward verifying improvements in resolution and throughput of a thicker cell than can be used on earth.

Source record↗
NASA NTRS1975

Clusius-Dickel Separations (CDS): A new look at an old technique

The history, applications, and theoretical basis of the CDS technique are reviewed. The advantage to be realized by conduction of CDSs in low-g, space environments are deduced. The results are reported of investigations aimed at further improving CDS efficiencies by altering convective flow patterns. The question of whether multicellular flow or turbulence can introduce a new separation mechanism which would boost separation efficiencies at least an order of magnitude is considered. Results are presented and discussed.

Grodzka, P. G.↗
NASA NTRS1976

The effects of solid rocket motor effluents on selected surfaces and solid particle size, distribution, and composition for simulated shuttle booster separation motors

A series of three tests was conducted using solid rocket propellants to determine the effects a solid rocket plume would have on thermal protective surfaces (TPS). The surfaces tested were those which are baselined for the shuttle vehicle. The propellants used were to simulate the separation solid rocket motors (SSRM) that separate the solid rocket boosters (SRB) from the shuttle launch vehicle. Data cover: (1) the optical effects of the plume environment on spacecraft related surfaces, and (2) the solid particle size, distribution, and composition at TPS sample locations.

Jex, D. W.↗