Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “room temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Reliability comparisons between additively manufactured and conventional SiC–Si ceramic composites

Abstract An additively manufactured reaction‐bonded silicon carbide ceramic composite is fabricated using a bimodal powder feedstock and the binder‐jetting printing technique. On fabricating, the ceramic is investigated to report its composition, mechanical, and thermal properties at room temperature and high temperatures (up to 750). The ceramic has a density of 2.76 g/cc, and shows a hardness of 21.74 GPa, and a flexure strength of 207.5 MPa at room temperature. The mechanical property of flexure strength is used to estimate its failure probability under applied stress, using a Weibull distribution. The mechanical properties and failure probabilities are compared with those of conventionally fabricated reaction‐bonded silicon carbide ceramics reported in the literature. These ceramics were fabricated using methods such as slip‐casting, compacting, and tape‐casting. The comparison is used to elucidate the advantages and areas of improvement of the present additive manufacturing technique for reaction‐bonded ceramics.

14 SOLAR ENERGY↗
DOE OSTI2025

Correlated Lattice Fluctuations in CsPbBr 3 Quantum Dots Give Rise to Long-Lived Electronic Coherence

Electronic coherence is central to numerous areas of science, from quantum biology to quantum materials. In quantum materials, lead-halide perovskite (LHP) quantum dots (QDs) have been shown to support electronic coherence through observation of coherent single-photon emission and superfluorescence arising from spatial coherence at low temperatures. In contrast, direct measurement of temporal coherence between exciton states has been lacking. Here, we employ coherent multi-dimensional spectroscopy to observe an electronic coherence between exciton states in CsPbBr 3 QDs that is long-lived at room temperature, surviving nearly three times longer than the electronic dephasing time. This observation of a long-lived electronic coherence at room temperature points to nearly perfectly correlated lattice fluctuations for each excitonic state in the superposition. In conclusion, these experiments reveal that the properties of LHP QDs extend to lattice dynamics that give rise to correlated fluctuations in the basis exciton states, a process that may next be optimized by design.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Gain Stability of Hamamatsu R5912-MOD Photo-Multipliers at Low Temperature

The Photon Detection System is a crucial component of the ICARUS detector in the Short Baseline Neutrino (SBN) Program at Fermi National Accelerator Laboratory (FNAL). It consists of 360 Photo Multiplier Tubes (PMTs) 8” Hamamatsu R5912-MOD and, since June 2020, it has been operated at the liquid Argon cryogenic temperature. During these years, the PMTs have shown gain losses as an aging effect. Using a climatic chamber at the INFN Sezione di Catania, we confirmed a stable gain for a single PMT 8” Hamamatsu 5912-MOD when operated at room temperature, and a persistent gain loss at temperatures around -70°C, although far from the liquid Argon one. No gain recovery was obtained bringing the PMT back to room temperature. We suspect that dynode deterioration due to temperature gradient plays a significant role in this phenomenon. During our test, the PMT was illuminated by a 520 nm laser source and operated in current mode. The laser beam was split into two optical fibers, the first one transmitting light through Neutral Density filters and then diffusing it over the surface of the PMT photocathode. The other optical fiber was used for an independent reference measurement of the injected light via a bolometric photodetector. In this presentation, the main technical characteristics of the measurement system are shown together with preliminary results which need further investigation to elucidate the underlying mechanisms driving the gain loss and to propose new mitigation strategies.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Thermally Activated Circularly Polarized Photoluminescence in a 2D Hybrid Perovskite with Giant Spin Splitting

Circularly polarized light generation and detection are critical for future spin-based technologies that inter-convert circularly polarized photons and electron spins. However, detailed mechanisms in such spin-photon interfaces are often either poorly understood or operate at cryogenic temperatures since typically small energies separating spin-split electronic bands facilitate thermally driven spin depolarization. Recently, several 2D hybrid perovskites with polar achiral cations were theoretically demonstrated to exhibit conduction and valence band spin-splitting energies greatly exceeding room-temperature thermal energy, suggesting their utility as spin-photon interfaces with practical operating temperatures. Here, a strong "spin memory" effect is reported in such a polar achiral layered perovskite that enables large room-temperature circularly polarized emission anisotropy following excitation with circularly polarized light. The polarization anisotropy depends strongly on temperature (thermally activated), excitation energy, and crystal orientation with respect to the excitation source. Temperature-dependent photoconductance measurements reveal similar thermally activated carrier generation. These observations suggest a mechanism whereby giant in-plane splitting of single-particle levels protects spin-polarization of photogenerated electrons and holes before recombination. Although polarized light emission is explored in greater detail in chiral perovskites, these results reveal that even without chirality, large spin memory in polar achiral perovskites can enable spin-photon interfaces that operate at elevated temperatures.

14 SOLAR ENERGY↗
DOE OSTI2023

Applying molecular dynamics simulations to the study of micro cold spray of yttria

Micro cold spray (MCS) is a novel manufacturing process with proven success depositing dense, thick films of technical ceramics without the need for elevated processing temperatures or chemical precursors. The process transforms a loose sub-micrometer powder into an adherent film with mechanical properties approaching that of the bulk material through a phenomenon known as room temperature impact consolidation. While this phenomenon has been demonstrated for a wide variety of ceramic materials and film substrates, yttria stands out as a material that is both well-characterized in experiments and of significant interest for industrial applications due to its excellent refractory properties. This dissertation seeks to investigate the fundamental mechanisms that enable room temperature impact consolidation by using molecular dynamics (MD) simulations of yttria particle impacts and characterizing the deformation behavior of the system.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solid State Solar Thermochemical Fuel (SoFuel) for Long Duration Storage

Efficient thermal storage systems, when coupled with renewable energy, enable the decarbonization of numerous industrial processes requiring high temperature steam or air, and provide a path for seasonal building heating, especially for colder climates. Existing thermal storage systems face a significant challenge due to losses inherent to all high temperature systems. A viable route to long-term storage is to use thermochemical reactions to convert concentrated solar energy to a fuel that is shelf-stable and can be stored at room temperature, thus eliminating losses associated with high temperature storage. The Solid-State Solar Thermochemical Fuel (SoFuel) technology developed by Michigan State University, Oregon State University, and Mississippi State University provides reactors and processes with minimal sensible heat losses and allows storing solar energy as a solid-state fuel at room temperature for long duration. The production of SoFuel occurs within a cylindrical cavity reduction chemical reactor that captures concentrated solar radiation from a solar field. Reactive magnesium manganese oxide (Mg-Mn-O) resides within the cylindrical cavity chemical reactor and undergoes thermal reduction as the temperature exceeds 1350°C. The thermally reduced Mg-Mn-O pellets (the SoFuel) are cooled down through a recuperative process and stored within a bin until used. The SoFuel can directly supply up to 1100°C heat to an adjacent power plant for electricity generation or industrial heating. Oxidation of SoFuel pellets occurs in a counter flow reactor and supplies heat to the user for electricity generation or industrial processing, after which the fuel is returned to the concentrating solar field where it is regenerated for re-use. Both reactors can be controlled well using a variety of strategies. With the low cost of the material, its cyclability, and the possibility of using the pelletized with on-sun reactors, or with electricity that would be curtailed, this project offers a viable option of medium- and long-term thermal energy storage.

14 SOLAR ENERGY↗
DOE OSTI2025

Solid State Solar Thermochemical Fuel (SoFuel) for Long Duration Storage

Efficient thermal storage systems, when coupled with renewable energy, enable the decarbonization of numerous industrial processes requiring high temperature steam or air, and provide a path for seasonal building heating, especially for colder climates. Existing thermal storage systems face a significant challenge due to losses inherent to all high temperature systems. A viable route to long-term storage is to use thermochemical reactions to convert concentrated solar energy to a fuel that is shelf-stable and can be stored at room temperature, thus eliminating losses associated with high temperature storage. The Solid-State Solar Thermochemical Fuel (SoFuel) technology developed by Michigan State University, Oregon State University, and Mississippi State University provides reactors and processes with minimal sensible heat losses and allows storing solar energy as a solid-state fuel at room temperature for long duration. The production of SoFuel occurs within a cylindrical cavity reduction chemical reactor that captures concentrated solar radiation from a solar field. Reactive magnesium manganese oxide (Mg-Mn-O) resides within the cylindrical cavity chemical reactor and undergoes thermal reduction as the temperature exceeds 1350°C. The thermally reduced Mg-Mn-O pellets (the SoFuel) are cooled down through a recuperative process and stored within a bin until used. The SoFuel can directly supply up to 1100C heat to an adjacent power plant for electricity generation or industrial heating. Oxidation of SoFuel pellets occurs in a counter flow reactor and supplies heat to the user for electricity generation or industrial processing, after which the fuel is returned to the concentrating solar field where it is regenerated for re-use. Both reactors can be controlled well using a variety of strategies. With the low cost of the material, its cyclability, and the possibility of using the pelletized with on-sun reactors, or with electricity that would be curtailed, this project offers a viable option of medium- and long-term thermal energy storage.

25 ENERGY STORAGE↗
DOE OSTI2023

Ferroelectric Domain Wall Engineering Enables Thermal Modulation in PMN–PT Single Crystals

Acting like thermal resistances, ferroelectric domain walls can be manipulated to realize dynamic modulation of thermal conductivity ( k ), which is essential for developing novel phononic circuits. Despite the interest, little attention has been paid to achieving room-temperature thermal modulation in bulk materials due to challenges in obtaining a high thermal conductivity switching ratio ( k high / k low ), particularly in commercially viable materials. Here, room-temperature thermal modulation in 2.5 mm-thick Pb(Mg 1/3 Nb 2/3 )O 3 – x PbTiO 3 (PMN– x PT) single crystals is demonstrated. With the use of advanced poling conditions, assisted by the systematic study on composition and orientation dependence of PMN– x PT, a range of thermal conductivity switching ratios with a maximum of ≈1.27 is observed. Further, simultaneous measurements of piezoelectric coefficient (d 33 ) to characterize the poling state, domain wall density using polarized light microscopy (PLM), and birefringence change using quantitative PLM reveal that compared to the unpoled state, the domain wall density at intermediate poling states (0< d 33 33,max ) is lower due to the enlargement in domain size. At optimized poling conditions (d 33,max ), the domain sizes show increased inhomogeneity that leads to enhancement in the domain wall density. This work highlights the potential of commercially available PMN– x PT single crystals among other relaxor-ferroelectrics for achieving temperature control in solid-state devices.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Probing the surface chemistry for reverse water gas shift reaction on Pt(1 1 1) using ambient pressure X-ray photoelectron spectroscopy

Using ambient pressure XPS (APXPS), we explored carbon dioxide (CO 2 ) adsorption and CO 2 hydrogenation on Pt(1 1 1) single crystal surface to observe the activation of CO 2 and the subsequent reaction mechanism. In pure CO 2 , we observed CO adsorbates and adsorbed oxygen on Pt(1 1 1) derived from CO 2 dissociation at room temperature. The introduction of H 2 (at a pressure ratio of 1:1 (H 2 :CO 2 )) increased the production of CO across all temperatures by facilitating the removal of surface oxygen. As a consequence, the surface could expose sites that could then be utilized for producing CO. Under these conditions, the reverse water–gas shift (RWGS) reaction was observed starting at 300 °C. At higher H 2 partial pressure (10:1 (H 2 :CO 2 )), the RWGS reaction initiated at a lower temperature of 200 °C and continued to enhance the conversion of CO 2 with increasing temperatures. Our results revealed that CO 2 was activated on a clean Pt(1 1 1) surface through the dissociation mechanism to form adsorbed CO and O at room temperature and at elevated temperatures. Introducing H 2 facilitated the RWGS as adsorbed oxygen was consumed continuously to form H 2 O, and adsorbed CO desorbed from the surface at elevated temperatures. This work clearly provides direct experimental evidence for the surface chemistry of CO 2 dissociation and demonstrates how hydrogen impacts the RWGS reaction on a platinum surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

How Cation Migration across a 2D/3D Interface Dictates Perovskite Solar Cell Efficiency

Perovskite solar cells with 2D/3D architecture are claimed to exhibit better stability compared to pristine 3D films at room temperature. However, under illumination and/or heat, cation migration causes the exchange of the bulky spacer cations (2D phase) with the smaller A-site cations (3D phase), creating a gradient heterostructure at the 2D/3D interface. We have evaluated the performance of BA 2 MAPb 2 I 7 /MAPbI 3 (2D/3D) and MAPbI 3 (3D) solar cells at different temperatures, while simultaneously probing the absorption changes of the 2D/3D perovskite layer and the photovoltaic performance of solar cell devices. The 2D/3D solar cells were more stable at room temperature but exhibited deterioration of photovoltaic performance at high temperatures. Here, by employing in situ measurements of operating solar cells to track both the photoconversion efficiency and absorption changes at different temperatures, we show that the cation exchange at the 2D/3D interface contributes to the efficiency losses.

14 SOLAR ENERGY↗
DOE OSTI2020

Emergent electric field control of phase transformation in oxide superlattices

Electric fields can transform materials with respect to their structure and properties, enabling various applications ranging from batteries to spintronics. Recently electrolytic gating, which can generate large electric fields and voltage-driven ion transfer, has been identified as a powerful means to achieve electric-field-controlled phase transformations. The class of transition metal oxides provide many potential candidates that present a strong response under electrolytic gating. However, very few show a reversible structural transformation at room-temperature. Here, we report the realization of a digitally synthesized transition metal oxide that shows a reversible, electric-field-controlled transformation between distinct crystalline phases at room-temperature. In superlattices comprised of alternating one-unit-cell of SrIrO 3 and La 0.2 Sr 0.8 MnO 3 , we find a reversible phase transformation with a 7% lattice change and dramatic modulation in chemical, electronic, magnetic and optical properties, mediated by the reversible transfer of oxygen and hydrogen ions. Strikingly, this phase transformation is absent in the constituent oxides, solid solutions and larger period superlattices. Our findings open up this class of materials for voltage-controlled functionality.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Large exotic spin torques in antiferromagnetic iron rhodium.

Spin torque is a promising tool for driving magnetization dynamics for computing technologies. These torques can be easily produced by spin-orbit effects, but for most conventional spin source materials, a high degree of crystal symmetry limits the geometry of the spin torques produced. Magnetic ordering is one way to reduce the symmetry of a material and allow exotic torques, and antiferromagnets are particularly promising because they are robust against external fields. We present spin torque ferromagnetic resonance (ST-FMR) measurements and second harmonic Hall measurements characterizing the spin torques in anti -ferromagnetic iron rhodium alloy. We report extremely large, strongly temperature-dependent exotic spin torques with a geometry apparently defined by the magnetic ordering direction. We find the spin torque efficiency of iron rhodium to be (207 +/- 94)% at 170 K and (88 +/- 32)% at room temperature. We support our conclusions with theoretical calculations showing how the antiferromagnetic ordering in iron rhodium gives rise to such exotic torques.

Gibbons, Jonathan↗
DOE OSTI2024

Deep-ultraviolet transparent conducting SrSnO 3 via heterostructure design

Exploration and advancements in ultrawide bandgap (UWBG) semiconductors are pivotal for next-generation high-power electronics and deep-ultraviolet (DUV) optoelectronics. Here, we used a thin heterostructure design to facilitate high conductivity due to the low electron mass and relatively weak electron-phonon coupling, while the atomically thin films ensured high transparency. We used a heterostructure comprising SrSnO 3 /La:SrSnO 3 /GdScO 3 (110), and applied electrostatic gating, which allow us to effectively separate charge carriers in SrSnO 3 from dopants and achieve phonon-limited transport behavior in strain-stabilized tetragonal SrSnO 3 . This led to a modulation of carrier density from 10 18 to 10 20 cm −3 , with room temperature mobilities ranging from 40 to 140 cm 2 V −1 s −1 . The phonon-limited mobility, calculated from first principles, closely matched experimental results, suggesting that room temperature mobility could be further increased with higher electron density. In addition, the sample exhibited 85% optical transparency at a 300-nm wavelength. These findings highlight the potential of heterostructure design for transparent UWBG semiconductor applications, especially in DUV regime.

Science & Technology - Other Topics↗
DOE OSTI2025

Homogenization of Dendritic Structures and the High-Temperature Strength of the Refractory High-Entropy Alloy MoNbTaVW

MoNbTaVW, a pioneering refractory high-entropy alloy (RHEA), is renowned for its exceptional strength at elevated temperatures. Like most RHEAs, it solidifies into a dendritic microstructure with steep concentration gradients, necessitating heat treatment for equilibration. Steep concentration gradients typically complicate mechanical property analysis and modeling, key challenges for high-throughput alloy discovery. This study examines the effects of high-temperature homogenization (1800 °C for 8 hours) on the microstructure and mechanical properties of MoNbTaVW across temperatures up to 1200 °C. Postmortem microstructural analysis, coupled with chemical, crystallographic, and mechanical assessments, revealed that yield strength was surprisingly insensitive to homogenization, with less than a 3 pct difference between as-cast and heat-treated materials. Nanoindentation confirmed minimal nanohardness changes across the dendritic structure at room temperature. However, homogenization significantly enhanced high-temperature work hardening, producing higher peak compressive strength. Both as-cast and homogenized MoNbTaVW exhibited room-temperature strengths of 1400 MPa, exceeding previously reported values. These findings demonstrate that high-temperature treatment enables microstructural homogenization without compromising strength, a unique behavior among RHEAs. In conclusion, while not universally applicable, this insight highlights the importance of understanding microstructural development in experimental alloys and offers a pathway to design alloys that achieve homogeneous-like properties without heat treatment.

Rietema, C. J. [Lawrence Livermore National Labora↗
DOE OSTI2025

Microstructure and mechanical behavior of a TiC nanoprecipitate strengthened V Alloy

The V-4Cr-4Ti (V44) alloys have been proposed as the prime candidate structural material for self-cooled liquid Li blanket and other designs for fusion energy applications. However, the applications of the V44 alloy are limited to a narrow operation temperature window, due to reduction in creep strength at or above 700 °C and susceptibility to irradiation hardening and embrittlement when irradiated below 400 °C. Here, in this work, we explore the feasibility of designing a novel V alloy to form a high number density of TiC nanoprecipitates, in order to simultaneously improve creep strength and provide defect sinks to mitigate irradiation hardening. Computational thermodynamics was used to design a new alloy (V44C) to achieve our goal of high TiC nanoprecipitates density within the alloy V44 matrix. To ensure scalability, the new alloy was made through arc-melting and ingot-casting followed by hot forging, cold rolling and heat treatments of homogenization and precipitation aging. The microstructure was characterized by SEM, TEM, XRD and APT, confirming the existence of nanoprecipitates predicted in the thermodynamic calculations. In addition to microstructural evaluation tensile properties at room temperature and 700 °C, and Charpy impact energy at room temperature were measured. The microstructure and mechanical properties were then compared with those from a historic reference V44 alloy. The tensile strength improvement in V44C was rationalized based on particle and solid solution strengthening mechanism. The fracture behavior was discussed based on the fractography results and necking deformation behavior.

Alloys development↗
DOE OSTI2025

Solid-state batteries enabled by ultra-high-frequency self-heating

Solid-state batteries (SSBs) are promising next-generation batteries due to their high energy density and enhanced thermal stability and safety. However, their sluggish kinetics and transport at room temperature result in high internal impedance and critically reduce the attainable discharge energy density. Taking advantage of their strong temperature-dependent ionic conductivity, here we introduce ultra-high-frequency (greater than 105 Hz) self-heating (UHFSH) of SSBs, which can rapidly warm up the batteries from room temperature to operating temperature (∼65°C) in less than a minute. As proof of concept, UHFSH experiments were conducted on symmetric solid-state cells with lithium aluminum germanium phosphate electrolyte in different configurations. Using an experimentally validated model, pack-level simulations predict fast heating (50 K/min) and minimized heating energy consumption (less than 4%). Without any modification of the materials or structure of the batteries, our non-intrusive self-heating strategy potentially enables SSBs to discharge more than 2-fold energy in 25°C ambient.

pulse heating↗
DOE OSTI2020

In situ characterization of residual stress evolution during heat treatment of SiC/SiC ceramic matrix composites using high-energy X-ray diffraction

Volumetric strains were measured in silicon carbide/silicon carbide melt-infiltrated ceramic matrix composites (CMCs) at ambient and high temperatures using high-energy synchrotron X-ray diffraction (XRD). Both silicon and silicon carbide constituents were interrogated utilizing a broad spectrum of diffracting planes that would be largely inaccessible to common laboratory XRD equipment. Residual room-temperature principal strains in the melt-infiltrated silicon phase were found to be approximately 1100 mu epsilon in compression, corresponding to stresses of approximately 300 MPa using simplifying constitutive assumptions. Residual room-temperature principal strains in silicon carbide particles found throughout the matrix were approximately 500 mu epsilon in tension, corresponding to approximately 300 MPa. Residual strains were found to decrease considerably as temperatures increased from ambient temperature to 1250 degrees C. Additionally, residual strains returned to approximately preheat treatment values after cool-down to ambient temperature. Strain measurements in the silicon phase were found to be significantly affected by dissolved boron dopant levels causing contraction of the silicon lattice. This contraction must be accounted for in high-temperature experiments for accurate calculation of stresses in the silicon phase.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Solvent-free and low temperature synthesis of chalcogenide Na superionic conductors for solid-state batteries

Sodium chalcogenide ionic conductors are attractive candidates as solid electrolytes (SEs) in solid-state Na metal batteries. They show the advantages of high ionic conductivity of 10 –4 –10 –2 S cm –1 at room temperature and great chemical stability in air. However, simple, efficient, and scalable approaches for the synthesis of chalcogenide solid electrolytes (SEs) are required. In this work, we report a solvent-free mixing to form dry intermediate products, which are subjected to different treatments (electron-beam assisted method or low temperature heating (≤150 °C)) to produce pure phase of Na 3 SbS 4-y Se y (0 ≤ y < 2) chalcogenides. Heavy Se-doping in Na 3 SbS 4 results in the tetragonal-to-cubic phase transition as well as a significant change of Sb-S bonding in Raman spectra. Among all chalcogenide SEs, Na 3 SbS 3 Se showed the highest ionic conductivity of 3.75 × 10 –4 S cm –1 at room temperature, 47% higher than that of pristine Na 3 SbS 4 . Moreover, the Se-dopant also enhanced the electrochemical stability towards Na metal in solid-state batteries. The solid-state Na||FeS 2 battery with Na 3 SbS 3 Se SE displayed long-term cycling ability up to 1,000 cycles within the voltage window of 1.0–2.7 V and retained a specific capacity of 105 mAh g –1 after 600 cycles. As a result, this technique promotes the practical applications of chalcogenide SEs in solid-state batteries.

25 ENERGY STORAGE↗