Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “process loads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Research into the effects of astronaut motion on the spacecraft: a review

The paper reviews the research that has been undertaken to understand and quantify the disturbance effects of the astronaut's motion inside and outside the spacecraft on the vehicle's attitude and acceleratory environment. In early investigations, the dynamic interaction of astronauts, modeled as point masses, and the spacecraft, modelled as a rigid body, was analyzed. Through ground-based experiments and the modeling of astronaut-induced forces and moments as stochastic processes, it became possible to estimate the magnitude and energy content of the loads produced by the astronaut. The first experiment in space to measure the astronaut-induced disturbances was conducted on the Skylab orbital station. Loads generated while performing routine operations were measured on board the Space Shuttle in 1994 and on the space station Mir in 1996-1997. c 2001 Elsevier Science Ltd. All rights reserved.

Skylab Project↗
NASA NTRS1991

Planning and Resource Management in an Intelligent Automated Power Management System

Power system management is a process of guiding a power system towards the objective of continuous supply of electrical power to a set of loads. Spacecraft power system management requires planning and scheduling, since electrical power is a scarce resource in space. The automation of power system management for future spacecraft has been recognized as an important R&D goal. Several automation technologies have emerged including the use of expert systems for automating human problem solving capabilities such as rule based expert system for fault diagnosis and load scheduling. It is questionable whether current generation expert system technology is applicable for power system management in space. The objective of the ADEPTS (ADvanced Electrical Power management Techniques for Space systems) is to study new techniques for power management automation. These techniques involve integrating current expert system technology with that of parallel and distributed computing, as well as a distributed, object-oriented approach to software design. The focus of the current study is the integration of new procedures for automatically planning and scheduling loads with procedures for performing fault diagnosis and control. The objective is the concurrent execution of both sets of tasks on separate transputer processors, thus adding parallelism to the overall management process.

Morris, Robert A.↗
NASA NTRS1993

Design and evaluation of a foam-filled hat-stiffened panel concept for aircraft primary structural applications

Geodesically stiffened structures are very efficient in carrying combined bending, torsion, and pressure loading that is typical of primary aircraft structures. They are also very damage tolerant since there are multiple load paths available to redistribute loads compared to prismatically stiffened structures. Geodesically stiffened structures utilize continuous filament composite materials which make them amenable to automated manufacturing processes to reduce cost. The current practice for geodesically stiffened structures is to use a solid blade construction for the stiffener. This stiffener configuration is not an efficient concept and there is a need to identify other stiffener configurations that are more efficient but utilize the same manufacturing process as the solid blade. This paper describes a foam-filled stiffener cross section that is more efficient than a solid-blade stiffener in the load range corresponding to primary aircraft structures. A prismatic hat-stiffener panel design is then selected for structural evaluation in uni-axial compression with and without impact damage. Experimental results for both single stiffener specimens and multi-stiffener panel specimens are presented. Finite element analysis results are presented that predict the buckling and postbuckling response of the test specimens. Analytical results for both the element and panel specimens are compared with experimental results.

Ambur, Damodar R.↗
NASA NTRS2008

Growth Control and Disease Mechanisms in Computational Embryogeny

This paper presents novel approach to applying growth control and diseases mechanisms in computational embryogeny. Our method, which mimics fundamental processes from biology, enables individuals to reach maturity in a controlled process through a stochastic environment. Three different mechanisms were implemented; disease mechanisms, gene suppression, and thermodynamic balancing. This approach was integrated as part of a structural evolutionary model. The model evolved continuum 3-D structures which support an external load. By using these mechanisms we were able to evolve individuals that reached a fixed size limit through the growth process. The growth process was an integral part of the complete development process. The size of the individuals was determined purely by the evolutionary process where different individuals matured to different sizes. Individuals which evolved with these characteristics have been found to be very robust for supporting a wide range of external loads.

Genetic algorithm↗
NASA NTRS1988

Information processing deficits in psychiatric populations: Implications for normal workload assessment

In one study, schizophrenics, bipolar manics, and mentally normal individuals were administered a digit recall task. The total performance of schizophrenics looked much like that of a normal processor under a higher load level. The manics' performance was intermediate. Primary performance was particularly poor among the mentally ill subjects. In a second study, three groups in the same populations as in the first study were asked to shadow and recall verbatim eight descriptive text passages. Distraction effects were found for schizophrenics only in the areas of percentage of words correctly shadowed and recall variables; the two areas were not correlated, however. It appears that, for schizophrenics, distraction disrupts the ability to effectively shadow information to a greater extent than it disrupts the ability to encode information for recall. The two studies imply that capacity-carrying abnormalities that affect the quantity but not the quality of information processing can be useful in pointing to information processing of normal humans under high load conditions.

Harvey, Philip D.↗
NASA NTRS1991

Horizontal stress in planetary lithospheres from vertical processes

Understanding the stress states in a lithosphere is of fundamental importance for planetary geophysics. It is closely linked to the processes which form and modify tectonic features on the surface and reflects the behavior of the planet's interior, providing a constraint for the difficult problem of determining interior structure and processes. The tectonics on many extraterrestrial bodies (Moon, Mars, and most of the outer planet satellites) appears to be mostly vertical, and the horizontal stresses induced by vertical motions and loads are expected to dominate the deformation of their lithospheres. Herein, only changes are examined in the state of stress induced by processes such as sedimentary and volcanic deposition, erosional denudation, and changes in the thermal gradient that induce uplift or subsidence. This analysis is important both for evaluating stresses for specific regions in which the vertical stress history can be estimated, as well as for applying the proper loading conditions to global stress models. All references to lithosphere herein should be understood to refer to the elastic lithosphere, that layer which deforms elastically or brittlely when subjected to geologically scaled stresses.

Banerdt, W. B.↗
NASA NTRS1987

An Application of Retroduction to Analyzing and Testing the Backing off of Nuts and Bolts During Dynamic Loading

The method of retroduction, adapted from the doctoral thesis of Dr. A. Croce, relies on a process of dialectic questioning that begins with the information sought, proceeds to Given items (either in the form of dimensions or limits of research). and to Known mathematical forms of analysis in design or to principles of study in research. Finally, analysis and synthesis are used to abstract the dielectic questions and to arrive at the information desired. This method is used to solve the engineering design problem of a beam and to determine why bolts and nuts vibrate apart. Both mathematical analysis and dialectic logical analysis are utilized. Results are provided of tests conducted to check the retroductive study of why and how nuts back off.

Kerley, James J.↗
NASA NTRS1976

Optimum load device for DMOS integrated circuits

Depletion-mode load devices can be integrated with DMOS transistors without any extra diffusions or ion implantation processing steps by judicious choice of the substrate crystal orientation and resistivity. For low voltage operation line-type 1, 1, 1 crystal orientation should be used. The line-type 1, 1, 1 crystal orientation also yields a higher transconductance for the DMOS transistor than the line-type 1, 0, 0 orientation. The geometry of the load device and the DMOS transistor can be made ratioless to conserve area. Self-aligned gates, hitherto considered incompatible with DMOS transistors, have been incorporated in the structure. The experimental DMOS inverters, using a conservative design, have achieved 4-ns propagation delay, 1.3-V operation, and 2-pJ propagation delay-power dissipation product.

Lin, H. C.↗
NASA NTRS2013

Analysis of Water Recovery Rate from the Heat Melt Compactor

Human space missions generate trash with a substantial amount of plastic (20% or greater by mass). The trash also contains water trapped in food residue and paper products and other trash items. The Heat Melt Compactor (HMC) under development by NASA Ames Research Center (ARC) compresses the waste, dries it to recover water and melts the plastic to encapsulate the compressed trash. The resulting waste disk or puck represents an approximately ten-fold reduction in the volume of the initial trash loaded into the HMC. In the current design concept being pursued, the trash is compressed by a piston after it is loaded into the trash chamber. The piston face, the side walls of the waste processing chamber and the end surface in contact with the waste can be heated to evaporate the water and to melt the plastic. Water is recovered by the HMC in two phases. The first is a pre-process compaction without heat or with the heaters initially turned on but before the waste heats up. Tests have shown that during this step some liquid water may be expelled from the chamber. This water is believed to be free water (i.e., not bound with or absorbed in other waste constituents) that is present in the trash. This phase is herein termed Phase A of the water recovery process. During HMC operations, it is desired that liquid water recovery in Phase A be eliminated or minimized so that water-vapor processing equipment (e.g., condensers) downstream of the HMC are not fouled by liquid water and its constituents (i.e., suspended or dissolved matter) exiting the HMC. The primary water recovery process takes place next where the trash is further compacted while the heated surfaces reach their set temperatures for this step. This step will be referred to herein as Phase B of the water recovery process. During this step the waste chamber may be exposed to different selected pressures such as ambient, low pressure (e.g., 0.2 atm), or vacuum. The objective for this step is to remove both bound and any remaining free water in the trash by evaporation. The temperature settings of the heated surfaces are usually kept above the saturation temperature of water but below the melting temperature of the plastic in the waste during this step to avoid any encapsulation of wet trash which would reduce the amount of recovered water by blocking the vapor escape. In this paper, we analyze the water recovery rate during Phase B where the trash is heated and water leaves the waste chamber as vapor, for operation of the HMC in reduced gravity. We pursue a quasi-one-dimensional model with and without sidewall heating to determine the water recovery rate and the trash drying time. The influences of the trash thermal properties, the amount of water loading, and the distribution of the water in the trash on the water recovery rates are determined.

Heat Melt Compactor↗
NASA NTRS1972

The development of a non-cryogenic nitrogen/oxygen supply system

Development of the hydrazine/water electrolysis process in a manned spacecraft to provide metabolic oxygen and both oxygen and nitrogen for cabin leakage makeup was studied. Electrode development efforts were directed to stability, achieved with catalyst additives and improved processing techniques, and a higher hydrazine conversion efficiency, achieved by reducing catalyst loading on the cathodes. Extensive testing of the one-man breadboard N2/02 system provided complete characterization of cabin atmosphere control aspects. A detailed design of a prototype modular N2/02 unit was conducted. The contact heat exchanger which is an integral component of this design was fabricated and sucessfully design-verification tested.

Greenough, B. M.↗
NASA NTRS1974

Dynamic-scanning-electron-microscope study of friction and wear

A friction and wear apparatus was built into a real time scanning electron microscope (SEM). The apparatus and SEM comprise a system which provides the capability of performing dynamic friction and wear experiments in situ. When the system is used in conjunction with dispersive X-ray analysis, a wide range of information on the wearing process can be obtained. The type of wear and variation with speed, load, and time can be investigated. The source, size, and distribution of wear particles can be determined and metallic transferal observed. Some typical results obtained with aluminum, copper, and iron specimens are given.

Brainard, W. A.↗
NASA NTRS1981

Effect of time-dependent flight loads on turbofan engine performance deterioration

An analytic evaluation of the dynamic effects of two flight load conditions of the JT9D-7/747 propulsion system is conducted. Predicted performance changes associated with a once-per-flight vertical gust and a typical revenue service landing are calculated. The predicted dynamic load effects on thrust specific fuel consumption are found to be negligible. The results indicate that the quasi-steady state approach to flight loads modeling is adequate to investigate the factors important to the deterioration process.

Lewis, B. L.↗
NASA NTRS1983

Lessons learned from the CSIS

A discussion is presented of the Centralized Storm Information System (CSIS), a joint effort by several organizations including NASA and the National Weather Service, which has been developed to aid the forecaster in evaluating weather data. The CSIS was developed to provide a handling, analyzing, intercomparison, and display system for real-time data from all available sources. The CSIS hardware and software, the impact of the CSIS, and the initial experience gained following the implementation of the CSIS are examined. Several general insights learned from this interactive processing system are examined in detail, including the benefits of an evolutionary bottom up rather than top down design approach, the crucial nature of scheduler function to any real time system, the recognition that meteorological interactive terminals requirements are different from image processing terminals requirements, and the knowledge that forecasters generate a large peak load on computer resources.

Mosher, F. R.↗
NASA NTRS1989

Acoustic design considerations: Review of rotor acoustic sources

It is not sufficient to optimize a rotor design in terms of a single noise level calculated for a single flight condition and a single measurement location. The various noise sources, their frequency content, amplitude, and directivity as a function of operating condition must be considered. A summary of the frequency ranges, directivity patterns and the most important operational and design parameters for major rotor noise sources is presented. It is difficult to generalize design requirements for rotor noise because the acoustic output varies so widely depending on the noise source, flight condition, measurement location, and frequency range. However, assuming the rotor must lift a fixed nominal payload and operate over a wide range of flight conditions, three general design guidelines can be stated: (1) minimize tip Mach number; (2) minimize blade thickness in the tip region; and (3) minimize gradients in the spanwise lift distribution in the tip region. Constraints on blade thickness, maximum values for hover tip Mach number, advancing tip Mach number and spanwise lift coefficient gradient will be specified during the aerodynamic, dynamic and structural optimization process. The rotor noise sources to be considered include the low frequency loading and thickness noise, and the higher frequency noise due to blade-vortex interactions (BVI). The analyses to be employed will include the comprehensive rotor analysis and design program CAMRAD and the rotor noise prediction program WOPWOP.

Martin, Ruth M.↗
NASA NTRS1991

Rectilinear partitioning of irregular data parallel computations

New mapping algorithms for domain oriented data-parallel computations, where the workload is distributed irregularly throughout the domain, but exhibits localized communication patterns are described. Researchers consider the problem of partitioning the domain for parallel processing in such a way that the workload on the most heavily loaded processor is minimized, subject to the constraint that the partition be perfectly rectilinear. Rectilinear partitions are useful on architectures that have a fast local mesh network. Discussed here is an improved algorithm for finding the optimal partitioning in one dimension, new algorithms for partitioning in two dimensions, and optimal partitioning in three dimensions. The application of these algorithms to real problems are discussed.

Nicol, David M.↗
NASA NTRS1990

Installing scientific instruments into a cold LHe dewar - The Gravity Probe B approach

Gravity Probe B is an orbital test of Einstein's general theory of relativity using gyroscopes. The precession of the gyroscopes will measure both the geodetic effect (6.6 arcsec/yr) through the curved space-time surrounding the earth and the motional effect (0.042 arcsec/yr) due to the rotating earth dragging space-time around with it. To achieve the extraordinary accuracies needed to measure these small precessions, it is necessary to have the gyroscopes operating in the following environments: a vacuum of less than 10 exp -10 torr; an acceleration level of less than 10 exp -10 g's; a magnetic field of less than 10 exp -7 gauss; and a temperature near 2 K. This paper discusses designs that allow scientific instruments to be installed into a dewar at 4.2 K. Methods for structurally supporting the instruments, transferring heat across joints at low temperature in vacuum, and excluding air during the insertion process are discussed. The structural support method is designed for Shuttle launch loads.

Parmley, Richard T.↗