Soluble, thermally-stable aromatic polyimides
Solubility of aromatic polyimides in organic solvents is increased by additions of dianhydride monomers and substituted diamines. Thermal stability of polymers is retained.
St. Clair, T. L.↗
SEARCH · Engineering Papers
Results for “polymer additive”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Polyenamines for Films, Coatings, and Adhesives
Easy process makes polymers with good mechanical properties. Synthesis involves Michael-type addition polymerization of two diacetylenic diketones, with various aromatic diamines in m-cresol at 60 to 130 degrees C. Technique provides synthetic route to high-molecular-weight polyenamines with moderate thermal stability and good mechanical properties. Polyenamines produced exhibit potential for use as films, coatings, adhesives, molding compounds, and composite matrices.
Hergenrother, Paul M.↗
Continuation of tailored composite structures of ordered staple thermoplastic material
The search for the cost effective composite structure has motivated the investigation of several approaches to develop composite structure from innovative material forms. Among the promising approaches is the conversion of a planar sheet to components of complex curvature through sheet forming or stretch forming. In both cases, the potential for material stretch in the fiber direction appears to offer a clear advantage in formability over continuous fiber systems. A framework was established which allows the simulation of the anisotropic mechanisms of deformation of long discontinuous fiber laminates wherein the matrix phase is a viscous fluid. Predictions for the effective viscosities of a hyper-anisotropic medium consisting of collimated, discontinuous fibers suspended in viscous matrix were extended to capture the characteristics of typical polymers including non-Newtonian behavior and temperature dependence. In addition, the influence of fiber misorientation was also modeled by compliance averaging to determine ensemble properties for a given orientation distribution. A design tool is presented for predicting the effect of material heterogeneity on the performance of curved composite beams such as those used in aircraft fuselage structures. Material heterogeneity can be induced during manufacturing processes such as sheet forming and stretch forming of thermoplastic composites. This heterogeneity can be introduced in the form of fiber realignment and spreading during the manufacturing process causing radial and tangential gradients in material properties. Two analysis procedures are used to solve the beam problems. The first method uses separate two-dimensional elasticity solutions for the stresses in the flange and web sections of the beam. The separate solutions are coupled by requiring that forces and displacements match section boundaries. The second method uses an approximate Rayleigh-Ritz technique to find the solutions for more complex beams. Analyses are performed for curved beams of various cross-sections loaded in pure bending and with a uniform distributed load. Preliminary results show that the geometry of the beam dictates the effect of heterogeneity on performance. The role of heterogeneity is larger in beams with a small average radius-to-depth ration, R/t, where R is the average radius of the beam and t is the difference between the inside and outside radii. Results of the anlysis are in the form of stresses and displacements and are compared to both mechanics of materials and numerical solutions obtained using finite element analysis.
Santare, Michael H.↗
Gas Sensor Evaluations in Polymer Combustion Product Atmospheres
Toxic gases produced by the combustion or thermo-oxidative degradation of materials such as wire insulation, foam, plastics, or electronic circuit boards in space shuttle or space station crew cabins may pose a significant hazard to the flight crew. Toxic gas sensors are routinely evaluated in pure gas standard mixtures, but the possible interferences from polymer combustion products are not routinely evaluated. The NASA White Sands Test Facility (WSTF) has developed a test system that provides atmospheres containing predetermined quantities of target gases combined with the coincidental combustion products of common spacecraft materials. The target gases are quantitated in real time by infrared (IR) spectroscopy and verified by grab samples. The sensor responses are recorded in real time and are compared to the IR and validation analyses. Target gases such as carbon monoxide, hydrogen cyanide, hydrogen chloride, and hydrogen fluoride can be generated by the combustion of poly(vinyl chloride), polyimide-fluoropolymer wire insulation, polyurethane foam, or electronic circuit board materials. The kinetics and product identifications for the combustion of the various materials were determined by thermogravimetric-IR spectroscopic studies. These data were then scaled to provide the required levels of target gases in the sensor evaluation system. Multisensor toxic gas monitors from two manufacturers were evaluated using this system. In general, the sensor responses satisfactorily tracked the real-time concentrations of toxic gases in a dynamic mixture. Interferences from a number of organic combustion products including acetaldehyde and bisphenol-A were minimal. Hydrogen bromide in the products of circuit board combustion registered as hydrogen chloride. The use of actual polymer combustion atmospheres for the evaluation of sensors can provide additional confidence in the reliability of the sensor response.
Delgado, Rafael H.↗
Multilayer Active Shell Mirrors for Space Telescopes
A novel active mirror technology based on carbon fiber reinforced polymer (CFRP) substrates and replication techniques has been developed. Multiple additional layers are implemented into the design serving various functions. Nanolaminate metal films are used to provide a high quality reflective front surface. A backing layer of thin active material is implemented to provide the surface-parallel actuation scheme. Printed electronics are used to create a custom electrode pattern and flexible routing layer. Mirrors of this design are thin (< 1.0 mm), lightweight (2.7 kg/m2 ), and have large actuation capabilities. These capabilities, along with the associated manufacturing processes, represent a significant change in design compared to traditional optics. Such mirrors could be used as lightweight primaries for small CubeSat-based telescopes or as meter-class segments for future large aperture observatories. Multiple mirrors can be produced under identical conditions enabling a substantial reduction in manufacturing cost and complexity. An overview of the mirror design and manufacturing processes is presented. Predictions on the actuation performance have been made through finite element simulations demonstrating correct abilities on the order of 250−300× for astigmatic modes with only 41 independent actuators. A description of the custom metrology system used to characterize the active mirrors is also presented. The system is based on a Reverse Hartmann test and can accommodate extremely large deviations in mirror figure (> 100 µm PV) down to sub-micron precision. The system has been validated against several traditional techniques including photogrammetry and interferometry. The mirror performance has been characterized using this system, as well as closed-loop figure correction experiments on 150 mm dia. prototypes. The mirrors have demonstrated post-correction figure accuracies of 200 nm RMS (two dead actuators limiting performance).
Reverse Hartmann↗
Layered Electrode Architectures Enabled by Holey Graphene Hosts
Battery electrodes are typically prepared using a slurry-based method, where high boiling point organic solvents are typically used with a polymer binder to disperse active electrode materials and conductive carbon additives followed by casting into current collector sheets. In this process, the use of organic solvents are environmentally hazardous, energy intensive, and time-consuming, while polymeric binders add weight and can undergo parasitic reactions during battery cycling. Here we discuss the use of a unique conductive carbon nanomaterial, namely holey graphene, as a multifunctional host that can be processed via a facile, solvent-free, binder-free, cold pressing method to prepare electrodes with unique architectures. This approach can accommodate a broad range of battery chemistries, such as lithium oxygen/carbon dioxide (Li-O2/CO2), lithium sulfur/selenium (Li-S/Se), and various lithium ion chemistries. The successful use of dry, cold compression allows the convenient modification of electrode mass loading with unique architectures containing active materials randomly mixed or layered with single or multiple layers of one or more active materials. In the conventional slurry-based electrode fabrication method, it is difficult, if not impossible, to achieve such layered architectures. In particular, the layered electrode architectures from the dry, cold press approach are easy to fabricate without significantly sacrificing device performance, and are amenable to continuous roll-to-roll dry processing. In addition, these architectures offer unprecedented perspectives on the battery material loading vs. utilization efficiency, as well as enabling unique characterization opportunities to advance mechanistic understanding of various battery chemistries. Potential applications of this unique electrode fabrication approach for solid-state batteries will also be discussed.
holey graphene, batteries, electrode architecture,↗
Waste Materials Recycling for In-Space Manufacturing
Logistics and resupply payloads for Lunar and Martian missions are significantly more cost and schedule prohibitive compared to LEO destinations. Recycling of waste and trash materials generated throughout the duration of a mission, as well as previous missions, will be critical for enabling sustained human presence beyond Earth. Currently, no solution exists for recycling waste materials back into feedstock form beyond entry-level hobbyist equipment, which is not suitable nor practical for space applications. There is already over 500,000 lbs of trash on the moon from previous missions, which will grow exponentially over the coming decade throughout the Artemis Campaign. Waste and trash materials are precious resources that, if recovered and properly processed, can be transformed back into usable feedstock form for on-demand manufacturing capabilities. Hence, it is prudent that a recycling solution be developed and infused into future missions.
additive↗
Titania Deposition on PMR-15
The formation, degree of crystallinity and adherence of dense titania (TiO2) thin film coatings on a high-temperature polyimide resin (PMR-15) can be influenced by the chemical composition of the polymer surface. Furthermore, solution deposition conditions can be adjusted to provide additional control over the morphology and crystallinity of the titania films. Recipes for solution-based titania deposition that used a slowly-hydrolyzing titanium fluoride salt in the presence of boric acid as a fluoride scavenger allowed growth of films up to 750 nm thick in 22 h. By adjusting solution pH and temperature, either amorphous titania or oriented crystalline anatase films could be formed. Surface sulfonate groups enhance the adhesion of solution-deposited oxide thin film coatings. While most sulfonation procedures severely damaged the PMR-15 surface, the use of chlorosulfonic acid followed by hydrolysis of the installed chlorosulfonyl groups provided effective surface sulfonation without significant surface damage. In some cases, the oxide deposition solution caused partial hydrolysis of the polymer surface, which itself was sufficient to allow adhesion of the titania film through chelation of titanium ions by exposed benzoic acid groups on the polymer surface.
Meador, Mary B.↗
Materials-of-Construction Radiation Sensitivity for a Fission Surface Power Convertor
A fission reactor combined with a free-piston Stirling convertor is one of many credible approaches for producing electrical power in space applications. This study assumes dual-opposed free-piston Stirling engines/linear alternators that will operate nominally at 825 K hot-end and 425 K cold-end temperatures. The baseline design options, temperature profiles, and materials of construction discussed here are based on historical designs as well as modern convertors operating at lower power levels. This notional design indicates convertors primarily made of metallic components that experience minimal change in mechanical properties for fast neutron fluences less than 10(sup 20) neutrons per square centimeter. However, these radiation effects can impact the magnetic and electrical properties of metals at much lower fluences than are crucial for mechanical property integrity. Moreover, a variety of polymeric materials are also used in common free-piston Stirling designs for bonding, seals, lubrication, insulation and others. Polymers can be affected adversely by radiation doses as low as 10(sup 5) - 10(sup 10) rad. Additionally, the absorbing dose rate, radiation hardness, and the resulting effect (either hardening or softening) varies depending on the nature of the particular polymer. The classes of polymers currently used in convertor fabrication are discussed along possible substitution options. Thus, the materials of construction of prototypic Stirling convertor engines have been considered and the component materials susceptible to damage at the lowest neutron fluences have been identified.
Bowman, Cheryl L.↗
Adaptation of Metal Additive Manufacturing Processes for the International Space Station
The In-Space Manufacturing (ISM) project at NASA Marshall Space Flight Center, in a partnership with the company, Made in Space, has previously investigated 3D printing of polymer materials on-orbit. In recent years, the project has begun exploring the potential for metal additive manufacturing (AM) on future space missions to reduce logistics and enable point-of-use manufacturing for sparing and repair. This presentation will provide an overview of constraints for demonstrating a manufacturing process on the International Space Station (ISS) as well as trades of available metal AM processes and their potential for in-space use. There are currently two processes in development as payloads for an ISS technology demonstration: wire+arc additive manufacturing (the Vulcan payload from Made in Space, Inc.) and bound metal deposition (the Fabrication Laboratory from Techshot, Inc). An update on both of these systems, results to date, and future development efforts will be presented. Relevant modeling work to evaluate operation of certain aspects of the processes in a microgravity environment will also be summarized.
manufacturing↗
Adaptation of Metal Additive Manufacturing Processes for the International Space Station
The In-Space Manufacturing (ISM) project at NASA Marshall Space Flight Center, in a partnership with the company, Made in Space, has previously investigated 3D printing of polymer materials on-orbit. In recent years, the project has begun exploring the potential for metal additive manufacturing (AM) on future space missions to reduce logistics and enable point-of-use manufacturing for sparing and repair. This paper provides an overview of constraints for demonstrating a manufacturing process on the International Space Station (ISS) as well as information on previous trades of available metal AM processes and their potential for in-space use. There are currently two processes in development as payloads for an ISS technology demonstration: wire+arc additive manufacturing (the Vulcan payload from Made in Space, Inc.) and bound metal additive manufacturing (the Fabrication Laboratory from Techshot, Inc). An update on both of these systems, key results to date, and future development efforts will be presented. Relevant modeling work, performed by NASA Ames Research Center, to evaluate operation of certain aspects of the bound metal AM process in a microgravity environment will also be summarized.
in-space manufacturing↗
High Performance Polymers and Composites (HiPPAC) Center
NASA University Research Centers funding has allowed Clark Atlanta University (CAU) to establish a High Performance Polymers and Composites (HiPPAC) Research Center. Clark Atlanta University, through the HiPPAC Center has consolidated and expanded its polymer and composite research capabilities through the development of research efforts in: (1) Synthesis and characterization of polymeric NLO, photorefractive, and piezoelectric materials; (2) Characterization and engineering applications of induced strain smart materials; (3) Processable polyimides and additives to enhance polyimide processing for composite applications; (4) Fabrication and mechanical characterization of polymer based composites.
Mintz, Eric A.↗
Dispersion of surface-modified, aggregated, fumed silica in polymer nanocomposites
Surface modification of model silica to enhance compatibility in nanocomposites has been widely studied. In addition to model spherical silica, several authors have investigated the impact of surface conditions on compatibility in commercial aggregated carbon black and silica. Here, dispersion is investigated for a series of nanocomposites produced from commercially modified fumed silica mixed with styrene butadiene rubber, polystyrene, and polydimethylsiloxane. Surface modification includes variation in surface hydroxyl content, siloxane, and silane treatment. Qualitatively, hydroxyl groups on the silica surface are considered incompatible with non-polar polymers, while methyl groups are compatible with oleophilic polymers. X-ray scattering was used to analyze the filler aggregate structure before and after dispersion, and the second virial coefficient was used to quantify nanodispersion. The content of surface moieties was determined from Fourier-transform infrared spectroscopy. It is observed that modified silica can display mean field or specific interactions as reflected by the presence of a correlation peak in x-ray scattering. For systems with specific interactions, a critical ordering concentration is observed related to the free energy change for structuring. A van der Waals model was used to model the second virial coefficient as a function of accumulated strain, yielding the excluded volume and an energetic term. The excluded volume could be predicted from the structural information, and the bound polymer layer was directly related to the surface methyl content, whereas the energetic term was found to synergistically depend on both the methyl and hydroxyl surface content.
36 MATERIALS SCIENCE↗
Oriented nanofibers embedded in a polymer matrix
A method of forming a composite of embedded nanofibers in a polymer matrix is disclosed. The method includes incorporating nanofibers in a plastic matrix forming agglomerates, and uniformly distributing the nanofibers by exposing the agglomerates to hydrodynamic stresses. The hydrodynamic said stresses force the agglomerates to break apart. In combination or additionally elongational flow is used to achieve small diameters and alignment. A nanofiber reinforced polymer composite system is disclosed. The system includes a plurality of nanofibers that are embedded in polymer matrices in micron size fibers. A method for producing nanotube continuous fibers is disclosed. Nanofibers are fibrils with diameters of 100 nm, multiwall nanotubes, single wall nanotubes and their various functionalized and derivatized forms. The method includes mixing a nanofiber in a polymer; and inducing an orientation of the nanofibers that enables the nanofibers to be used to enhance mechanical, thermal and electrical properties. Orientation is induced by high shear mixing and elongational flow, singly or in combination. The polymer may be removed from said nanofibers, leaving micron size fibers of aligned nanofibers.
Barrera, Enrique V.↗
A review of the fabrication methods and mechanical behavior of continuous thermoplastic polymer fiber–thermoplastic polymer matrix composites
Abstract Thermoplastic polymer fiber–thermoplastic polymer matrix composites (PPCs or PRFPs), often recognized as self‐reinforced or single polymer composites, are potential candidates for future advanced polymer composites because of various advantages ( e.g., recyclability, formability, low‐cost, ultra‐lightweight, environmental friendliness, etc.). The manufacturability and mechanical behavior of these composites compared to conventional carbon‐/glass‐/aramid‐fiber‐reinforced polymers is of great interest to the composites community, but there are a limited number of studies in this area. To this end, this paper reviewed fabrication methods with different processing parameters and mechanical behavior of uni‐/multi‐directional thermoplastic PPCs featuring continuous thermoplastic polymer fibers from limited data in the literature. It was shown that most specific behaviors (normalized by density) of these materials in various loading conditions (e.g., quasi‐static tension/shear/flexure, tension‐tension fatigue, and out‐of‐plane impacting, etc.) are comparable to or better than glass‐/aramid‐fiber‐reinforced polymers. Particularly, the specific ductility in the foregoing conditions outperforms all the carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Thermoplastic PPCs with remarkable performance can be achieved through several uncomplicated methods (e.g., film stacking, hot compaction, powder and solution impregnations, matrix infusion and injection molding, additive manufacturing, etc.), which have some similarities to the methods used for carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Moreover, several opportunities and challenging problems of thermoplastic PPCs were summarized at the end of this review paper. Efficient solutions may require countless efforts in the composites community to further strengthen the performance and understanding of thermoplastic PPCs for wide applications in various engineering fields in the future.
36 MATERIALS SCIENCE↗
Segmental relaxation of sequence defined polymers
For this work, the dynamical behavior of sequence defined polymers, P(C n EG 4 ), was studied using dielectric spectroscopy showing one segmental relaxation in addition to a secondary relaxation. In case of segmental relaxation, the relaxation times strongly depend on the molecular weight at low temperatures, while at higher temperatures, unlike to linear homo polymers, this effect levels out. With increasing length of C-units, the segmental relaxation accelerates. This is also reflected in the glass transition temperature, extracted from dielectric spectroscopy. With increasing length of C-units the glass transition temperature decreases, compatible with the accelerated segmental relaxation.
36 MATERIALS SCIENCE↗
Plasticizer for polymide composites
Problem of maintaining good prepreg tack and drape has been solved by modification of addition polymide. Tack and drape are ability of prepreg to adhere to adjacent plies and to conform to desired shape during layup process. Alternate approach allows both longer life of polymer prepreg and processing of low-void laminates. It appears to be applicable to all addition polymide systems. Modified addition polymide takes advantage of reactive liquid plasticizer, monoethylphthalate, which is used in place of solvent. Because of low vapor pressure of reactive liquid, it is retained and, thereby, tack and flexibility of prepreg are retained.
St. Clair, T. L.↗
Immune-compatible designs of semiconducting polymers for bioelectronics with suppressed foreign-body response
One of the greatest obstacles to achieving implantable electronics with long-term functionality and minimized inflammatory reactions is the immune-mediated foreign-body response (FBR). Recently, semiconducting polymers with mixed electron–ion conductivity have been demonstrated as promising candidates to achieve direct electrical interfacing on bio-tissues. However, there is limited understanding of their immune compatibility in vivo, and strategies for minimizing the FBR through molecular design remain underexplored. Here we introduce a set of molecular design strategies for enhancing the immune compatibility of semiconducting polymers. Specifically, we show that selenophene, when incorporated in the backbone, can mitigate the FBR by suppressing macrophage activation. In addition, side-chain functionalization with immunomodulatory groups decreases the FBR further by downregulating the expression of inflammatory biomarkers. Together, our synthesized polymers achieve suppression of the FBR by as much as 68% (as indicated by the collagen density). In the meantime, these immune-compatible designs still provide a high charge-carrier mobility of around 1 cm 2 V −1 s −1 . In conclusion, we anticipate that such immune-compatible design principles can be translated to a variety of conjugated polymers to suppress the FBR for implantable applications.
Li, Nan [University of Chicago, IL (United States)↗