Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance gain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Results from flight and simulator studies of a Mach 3 cruise longitudinal autopilot

At Mach numbers of approximately 3.0 and altitudes greater than 21,300 meters, the original altitude and Mach hold modes of the YF-12 autopilot produced aircraft excursions that were erratic or divergent, or both. Flight data analysis and simulator studies showed that the sensitivity of the static pressure port to angle of attack had a detrimental effect on the performance of the altitude and Mach hold modes. Good altitude hold performance was obtained when a high passed pitch rate feedback was added to compensate for angle of attack sensitivity and the altitude error and integral altitude gains were reduced. Good Mach hold performance was obtained when the angle of attack sensitivity was removed; however, the ride qualities remained poor.

Gilyard, G. B.↗

Sequential design of a linear quadratic controller for the Deep Space Network antennas

A new linear quadratic controller design procedure is proposed for the NASA/JPL Deep Space Network antennas. The antenna model is divided into a tracking subsystem and a flexible subsystem. Controllers for the flexible and tracking parts are designed separately by adjusting the performance index weights. Ad hoc weights are chosen for the tracking part of the controller and the weights of the flexible part are adjusted. Next, the gains of the tracking part are determined, followed by the flexible controller final tune-up. In addition, the controller for the flexible part is designed separately for each mode; thus the design procedure consists of weight adjustment for small-size subsystems. Since the controller gains are obtained by adjusting the performance index weights, determination of the weight effect on system performance is a crucial task. A method of determining this effect that allows an on-line improvement of the tracking performance is presented in this article. The procedure is illustrated with the control system design for the Deep Space Station (DSS)-13 antenna.

Gawronski, W.↗

State-of-the-art and evolution of UFSD sensors design at FBK

Over the past few years, there has been growing interest in the development of silicon sensors able to simultaneously measure accurately the time of passage and the position of impinging charged particles. In this contribution, a review of the progresses in the design of UFSD (Ultra-Fast Silicon Detectors) sensors, manufactured at the FBK (Fondazione Bruno Kessler) Foundry, aiming at tracking charged particles in 4 dimensions, is presented. The state-of-the-art UFSD sensors, with excellent timing capability, are planned to be used in both ATLAS and CMS experiments detector upgrade, in order to reduce the background due to the presence of overlapping events in the same bunch crossing. The latest results on sensors characterization including time resolution, radiation resistance and uniformity of the response are here summarized, pointing out the interplay between the design of the gain layer and the UFSD performances. The research is now focusing on the maximization of the sensor fill factor, to be able to reduce the pixel size, exploring the implementation of shallow trenches for the pixel isolation and the development of resistive AC-coupled UFSD sensors. In conclusion, a brief review on research paths tailored for detection of low energy X-rays or for low material budget applications is given.

47 OTHER INSTRUMENTATION↗

Feeding Ten Billion People Is Possible Within Four Terrestrial Planetary Boundaries

Global agriculture puts heavy pressure on planetary boundaries, posing the challenge to achieve future food security without compromising Earth system resilience. On the basis of process-detailed, spatially explicit representation of four interlinked planetary boundaries (biosphere integrity, land-system change, freshwater use, nitrogen flows) and agricultural systems in an internally consistent model framework, we here show that almost half of current global food production depends on planetary boundary transgressions. Hotspot regions, mainly in Asia, even face simultaneous transgression of multiple underlying local boundaries. If these boundaries were strictly respected, the present food system could provide a balanced diet (2,355 kcal per capita per day) for 3.4 billion people only. However, as we also demonstrate, transformation towards more sustainable production and consumption patterns could support 10.2 billion people within the planetary boundaries analysed. Key prerequisites are spatially redistributed cropland, improved water–nutrient management, food waste reduction and dietary changes. Adoption of the Sustainable Development Goals by all nations in 2015 is the first ever commitment to a world development path that safeguards the stability of the Earth system as a prerequisite for meeting universal human standards1. The longstanding challenge of achieving food security through sustainable agriculture is particularly acute in this context as world agriculture is a leading cause for the current transgressions of multiple planetary boundaries (PBs) globally and regionally2–5. The PB framework is a comprehensive scientific attempt to synoptically define our planet’s biogeophysical limits to anthropogenic interference. It suggests bounds to nine interacting processes that together delineate a Holocene-like Earth system state. The Holocene is chosen as the reference state as it is the only period known to provide a safe operating space for a world population of several billion people, and according to a precautionary principle, the PBs are set in sufficient distance from processes that may critically undermine Earth system resilience and global sustainability. A challenging question, thus, is whether human development goals such as food security can be met while maintaining multiple PBs along with their subglobal manifestations. Further PB transgressions could jeopardize the chances of providing sufficient food for a world population projected to be wealthier and reach >9 billion by 2050. This conundrum portrays a tradeoff between Earth’s biophysical carrying capacity and humankind’s rising food demand, calling in response for radical rethinking of food production and consumption patterns6–9. Yield gap closures, avoidance of excessive input use, shifts towards less resource-demanding diets, food waste reductions and efficient international trade are crucial options for sustainably increasing the food supply10–15. For example, enhancing water-use efficiency on irrigated and rain-fed farms can triple or quadruple crop yields in low-performing systems, suggesting possible global gains of >20% (ref. 16). Even higher gains appear feasible through globally optimized configurations of the land-use pattern17, and cutting food losses by half could generate food for another billion people18. Thus, collective large-scale implementation of such options could sustain food for a further growing world population19. Yet achieving this within a safe operating space as defined by PBs requires not only a halt to but actually a reversal of existing PB transgressions. Previous studies suggest that such a reconciliation might be possible, but these were based on aggregate representations of PBs (not accounting for the spatial patterns of limits, transgressions and interactions) or considered only one boundary in isolation17,20–23. Here, we systematically quantify to what extent current food production depends on local to global transgressions of the PBs for biosphere integrity, land-system change, freshwater use and nitrogen (N) flows, along with the potential of a range of solutions to avoid these transgressions and still increase food supply (Table 1). To this end, we configured an internally consistent process-based model of the terrestrial biosphere including agriculture (LPJmL) with multiple spatially distributed PBs and their interactions. LPJmL is among the longest-established and best-evaluated biosphere models, showing robust performance regarding simulation of, for example, carbon, water and crop yield dynamics (Supplementary Figs. 1 and 2 and Supplementary Table 1; see ref. 24 for a comprehensive benchmarking and Supplementary Methods for more detail on model evaluations). In principle following established definitions4, we refine the computation of some PBs with respect to their regional patterns and interactions (Methods), providing globally gridded precautionary limits to human interference with the Earth system at a level of great detail. In particular, we account for the evidence that many PBs need to be represented spatially explicitly4 to cover their

Gerten, Dieter↗

Digital control of high performance aircraft using adaptive estimation techniques

In this paper, an adaptive signal processing algorithm is joined with gain-scheduling for controlling the dynamics of high performance aircraft. A technique is presented for a reduced-order model (the longitudinal dynamics) of a high performance STOL aircraft. The actual controller views the nonlinear behavior of the aircraft as equivalent to a randomly switching sequence of linear models taken from a preliminary piecewise-linear fit of the system nonlinearities. The adaptive nature of the estimator is necessary to select the proper sequence of linear models along the flight trajectory. Nonlinear behavior is approximated by effective switching of the linear models at random times, with durations reflecting aircraft motion in response to pilot commands.

Van Landingham, H. F.↗

Analysis of gain scheduled control for nonlinear plants

Gain scheduling has proven to be a successful design methodology in many engineering applications. In the absence of a sound theoretical analysis, these designs come with no guarantees of the robustness, performance, or even nominal stability of the overall gain-scheduled design. An analysis is presented for two types of nonlinear gain-scheduled control systems: (1) scheduling on a reference trajectory and (2) scheduling on the plant output. Conditions which guarantee stability, robustness, and performance properties of the global gain schedule designs are given. These conditions confirm and formalize popular notions regarding gain-scheduled designs, such as that the scheduling variable should vary slowly and capture the plant's nonlinearities.

Shamma, Jeff S.↗

EVs@Scale Next-Gen Profiles - EV Profile Capture 2023

As part of the U.S. DOE EVs@Scale consortium Next-Gen Profiles (NGP) project, the profile capture of production electric vehicles undergoing high power charging (HPC) is conducted over a wide range of conditions to explore variance and performance. Charge session parameters are collected from both the electric vehicle (EV) and electric vehicle supply equipment (EVSE) at a rate of 10Hz and entered into a time-series database for analysis. These charge profiles are captured under nominal and off-nominal conditions, exploring the impact of battery state of charge (SOC), battery temperature, vehicle condition, smart charge management (SCM), and EVSE limitations. Nominal conditions are defined to be ideal conditions that should transfer the maximum allowable energy in the minimum possible amount of time. Nominal condition profiles are compared across EVs to characterize state-of-the-art EV charging performance against one another. Off-nominal condition profiles are compared against its nominal condition profile counterpart to highlight the variance across less desirable starting conditions within a single EV. Under nominal conditions, most EVs can achieve the original equipment manufacturer (OEM) rated peak-power and charge times. Peak power across EVs has variance due to the vehicle design, battery topology, charging strategy, etc. These 10-100% nominal preconditioned charge profiles across 13 EVs (11 light-duty (LD), 2 heavy-duty (HD)) were used for analysis in power curve analysis, power distribution, SOC and range comparison, thermal impacts of current draw, battery pack size and energy charged, and ramp rates. Power curve analysis show the uniqueness in power vs time curves across all EVs, breaking down the features of a typical profile and where variation is typically seen. Power distribution results showed that over 50% of charge time is spent below 50kW and only 12.1% is spent above 200kW. SOC and range performance yielded different top performing EVs when exploring goals of performance from SOC and range gained after 10-min (EV2) and 20-min (EV8), and time-to-achieve 80% SOC (EV8) and 200 miles of range (EV1). Current draw from 400-volt EVs had a higher thermal impact to cable/connector temperatures when compared to 800-volt EVs, due to a higher current requirement to achieve similar power levels. There was high variance in C rating, a useful metric when comparing the relationship between peak/average charge session power and relative battery pack size, across EVs under test. Ramp rates during initial power transfer were examined, fastest and slowest speeds ranging from 192.5kW/second to 2.6kW/second respectively. A similar analysis of ramp rates was also conducted for OCPP curtailment testing, where EVs underwent a 2-minute 65A curtailment request before returning to full-power charge. Under off-nominal conditions, most EVs experienced variation from the nominal condition profiles. EVs that underwent the full set of NGP defined testing conditions were compared, analysis of which was categorized by 800-volt and 400-volt EVs. It should be noted that the 800-volt EVs had significantly higher peak power ratings than the 400-volt EVs, and thus were more prone to variance. Initial state of charge, battery temperature, and vehicle condition had a considerable impact on peak power levels and charge time for the 800-volt vehicles under test. EVSE limited tests lowered achievable power down to 200kW, greatly impacted 800-volt charging power, and had little to no effect on 400-volt charging power. Adapter testing was performed on a single 400-volt EV, where power and current limitations were found but overall charge time was not significantly impacted. Adapter and boost converter testing was performed on a single 800-volt EV, where both charge power and charge time were greatly impacted. Charge profiles are unique, and comparing such requires analysis that examines starting conditions, vehicle and battery topologies,

Charging↗

Gain balanced nonlinear optical interferometer

A nonlinear fiber interferometer is disclosed suitable for fiber sensor and other applications. A first nonlinear fiber section amplifies probe and conjugate sidebands of a pump through four-wave mixing. A second section introduces a phase shift to be measured, for example from a sensor. A third nonlinear fiber section amplifies with phase-sensitive gain to increase signal-to-noise ratio. Based on phase-sensitive output power of probe and/or conjugate components, the phase shift can be measured. Superior performance can be obtained by balancing gain between the (first and third) nonlinear sections. Non-fiber, for example photonic integrated circuit, embodiments are disclosed. Differential sensing, alternative detection schemes, sensing applications, associated methods, and other variations are disclosed.

42 ENGINEERING↗

Gain balanced nonlinear optical interferometer

A nonlinear fiber interferometer is disclosed suitable for fiber sensor and other applications. A first nonlinear fiber section amplifies probe and conjugate sidebands of a pump through four-wave mixing. A second section introduces a phase shift to be measured, for example from a sensor. A third nonlinear fiber section amplifies with phase-sensitive gain to increase signal-to-noise ratio. Based on phase-sensitive output power of probe and/or conjugate components, the phase shift can be measured. Superior performance can be obtained by balancing gain between the (first and third) nonlinear sections. Non-fiber, for example photonic integrated circuit, embodiments are disclosed. Differential sensing, alternative detection schemes, sensing applications, associated methods, and other variations are disclosed.

Lukens, Joseph M.↗

Gain balanced nonlinear optical interferometer

A nonlinear fiber interferometer is disclosed suitable for fiber sensor and other applications. A first nonlinear fiber section amplifies probe and conjugate sidebands of a pump through four-wave mixing. A second section introduces a phase shift to be measured, for example from a sensor. A third nonlinear fiber section amplifies with phase-sensitive gain to increase signal-to-noise ratio. Based on phase-sensitive output power of probe and/or conjugate components, the phase shift can be measured. Superior performance can be obtained by balancing gain between the (first and third) nonlinear sections. Non-fiber, for example photonic integrated circuit, embodiments are disclosed. Differential sensing, alternative detection schemes, sensing applications, associated methods, and other variations are disclosed.

Lukens, Joseph M.↗

Flight evaluation of a Mach 3 cruise longitudinal autopilot

At high Mach numbers (approximately 3) and altitudes greater than 70,000 feet, the original altitude and Mach hold modes of the YF-12 autopilot produced aircraft excursions that were erratic or divergent or both. Data analysis and simulator studies showed that static pressure port sensitivity to angle of attack had a detrimental effect on the performance of both altitude and Mach hold modes. Good altitude hold performance was obtained when a high-passed pitch rate feedback was added to compensate for angle-of-attack sensitivity and the altitude error and integral altitude gains were reduced. Good Mach hold performance was obtained with the removal of angle-of-attack sensitivity.

Gilyard, G. B.↗

Bayesian model updating with finite element vs surrogate models: Application to a miter gate structural system

Bayesian finite element (FE) model updating using direct model evaluations of large-scale high-fidelity FE models is extremely computationally expensive. Surrogate models can be used as fast emulators of FE models to accelerate the model calibration process. The physics/mechanics-based FE models are still the underpinning behind the surrogate models. Here, this paper evaluates the loss in accuracy and the gain in computational time while performing Bayesian model updating by using surrogate model evaluations compared to using direct FE model evaluations. This evaluation is crucial before entirely relying on surrogate models in model updating for structural health monitoring (SHM) and damage prognosis (DP) purposes. This paper also demonstrates Bayesian updating and surrogate model construction of large-scale high-fidelity FE models of infrastructure systems. In this regard, the miter gate structural system is considered as the testbed structure. Three predominant damage modes (loss of contact between gate and wall, loss of thickness due to corrosion, and loss of tension in the diagonal rods) are considered for model updating purposes. Bayesian model updating is performed using direct FE evaluations by leveraging parallel computing. Two types of surrogates, namely polynomial chaos expansion (PCE) and Gaussian process regression (GPR), are developed for the miter gate. Model updating is performed again using the trained surrogate models, and the updating results are compared with their counterparts obtained using the direct FE evaluation results. The posterior distribution of the FE model parameters obtained using the trained surrogates are sufficiently accurate with respect to the posterior obtained utilizing the direct FE evaluations. In addition, an approximate 4-fold decrease in the computational time was observed when using surrogate model evaluations instead of direct FE evaluations for model updating.

42 ENGINEERING↗

Ethanol to diesel: a sustainable alternative for the heavy-duty transportation sector

The combustion of middle distillates (diesel and jet fuel) is responsible for the emission of more than 2 GTon of CO 2 per year worldwide. While sustainable alternatives exist for gasoline and jet fuel, we still lack sustainable alternatives for diesel. This fact is especially relevant if we consider that electrification of sectors where diesel is used is challenging. One sustainable approach for diesel production is the catalytic upgrading of ethanol. While most work in this field has focused on the dehydration/oligomerization of ethanol, this approach is limited to producing fuels that have a high degree of branching and low cetane number. Another approach is the sequential use of ethanol Guerbet coupling, leading to higher alcohols, followed by etherification, leading to large ethers which, importantly, result in a product with high cetane number. In this work, we explore the catalytic upgrading of ethanol into diesel following an approach based on the initial Guerbet coupling of ethanol followed by etherification. The results presented are a collaborative and synergic effort among process and systems engineers, experimentalist in the area of catalysis, and fuel property modelers. Here, we demonstrate experimentally the feasibility of upgrading ethanol into a diesel fuel with properties that surpass its fossil counterpart. The diesel produced has a predicted cetane number of ~70 and outstanding cold flow properties, while maintaining other properties (viscosity, density, and flash point) within expected ranges. A technoeconomic analysis performed based on a detailed biorefinery model shows that the MFSP is ~5.89$ per Gal in 2021 dollars when lignocellulosic ethanol is used, with the most relevant economic driver the cost of the ethanol feedstock. The upgrading process can be performed with a net energy gain (EROI = 1.49 > 1). An LCA analysis of greenhouse gas (GHG) emissions reveals that the use of lignocellulosic ethanol may lead to more than 50% reduction in GHG emissions compared to fossil diesel. Depending on the CO 2 emissions associated with the production of ethanol we show that in some instances the production of carbon neutral diesel fuel is possible.

09 BIOMASS FUELS↗

Introduction to the special topic on inertial confinement fusion diagnostics

In the first decade of the 21st century, the United States began operating three leading Inertial Confinement Fusion (ICF) and High-Energy Density Physics (HEDP) facilities. The National Ignition Facility (NIF) began its quest to first surpass the Lawson Criterion and then reach thermonuclear ignition and thermonuclear gain. The Omega EP (Extended Performance) laser provides unprecedented energy, reliability, and consistency for petawatt (PW)-class laser experiments. The Omega laser continues to support over 1000 ICF and HEDP experiments each year. The Z pulsed power machine is a Z-pinch plasma confinement device that was refurbished to increase current drive and improve reliability. The extreme states of matter created in these new facilities required advancement of many technologies. The most important among these was the significant improvement in instrumentation capabilities needed to diagnose plasma conditions and resulting nuclear products. The instruments needed a better temporal, spatial, and energy resolution. They also needed to be hardened against EMP and radiation. Typical events in an ICF implosion include compressing the deuterium–tritium (DT) fuel to greater than 60 g/cm 3 and heating the DT to a temperature greater than 10 keV (110 000 000 K). The DT atoms react to produce 14 MeV neutrons from a volume with a radius of ~30 μm. When the fuel ignites, the DT burn prop agates into cold fuel and the neutron-emitting region can reach sizes of over 200 μm. Furthermore, the burn typically lasts less than 150 ps, but the burn duration will decrease as the DT yield increases. Burn durations as short as 90 ps have been recorded and are predicted to decrease still further to 20 ps. X-ray imaging diagnostics are needed to measure the acceleration and velocity of the capsule enclosing the DT, where the implosion velocities can reach over 400 km/s.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High-rate heavy-ion tracking using MWPCs and PPACs with an Anti-Discharge Unit

This work reports on the development of two robust, heavy-ion beam tracking concepts operating at low pressure (< 15 Torr) for high rate applications (> 200 kHz). The first concept consists of a Multi-Wire Proportional Counter (MWPC) with a central anode consisting of 12 μm Au-plated Tungsten wires spaced 1 mm from each other. The anode grid is sandwiched between two segmented cathodes aligned orthogonally in the two dimensions for (x,y) particle localization. The second detector is a Parallel-Plate Avalanche Counter (PPAC) that uses the same readout geometry as the MWPC, but replaces the wire anode with a 150 nm silver layer deposited on both sides of a thin (< 1 mg/cm 2 ) polypropylene foil. Additionally, the bias circuitry for the PPAC anode central foil is equipped with an Anti-Discharge Unit (ADU) to prevent transitions from proportional operation to streamer formation, thereby avoiding damaging discharges. The localization capability of both detectors was tested with a low-rate alpha-particle source (241-Am). A position resolution of < 1 mm (FWHM) was achieved under stable, high-gas-gain (> 1000) operating conditions. Their performance in terms of detection efficiency as a function of the isotope charge (Z) was determined by irradiating the detectors with a cocktail beam (Z ≤ 15) with energy of ∼ 100 MeV/u. Full detection efficiency is maintained for all available fragments under optimal operational conditions (i.e., voltage bias). Full detection efficiency was achieved at rates above 200 kHz by irradiating the detectors with a 1 cm diameter 238 U beam at an energy of 143 MeV/u.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Forecast of Wildfire Potential Across California USA Using a Transformer

Wildfires are a major issue facing the United States, a matter further exacerbated by an ever-changing climate. In California alone, wildfires are responsible for billions of dollars in damages and take lives each year. Accurately predicting fire danger conditions allows preparation awareness before wildfires start. Transformers are a class of deep learning models designed to identify patterns in sequential datasets. In recent years, transformers have gained popularity through their impressive performance in natural language processing and other applications of signal recognition. This analysis demonstrates the ability of a transformer with a residual connection to forecast fire danger potential over the state of California. Wildland fire potential index (WFPI) maps collected from the US Geological Survey database from January 1st 2020 to December 31st 2023 were used to tune, train and evaluate the transformer. Meteorological inputs (provided by Daymet daily weather and climatological summaries), the normalized difference vegetation index (NDVI) (calculated from the Moderate Resolution Imaging Spectroradiometer (MODIS)), and outputs from the Scott and Burgman fire behavior fuel models (to characterize maps of fuel types), were used as inputs. Our results show that a transformer can effectively emulate the US Forest Service modeled WFPI maps of California USA for four week long forecasts over the month of July, 2023, with correlations ranging from 0.85 – 0.98.

Limber, Russell [ORNL]↗

Dynamic Model of Active Front-End Converters with 2DOF-PI Controllers for DC Bus Voltage Control

In most of the research, a conventional one degree-of-freedom type proportional-integral controller (1DOF-PI) is used for the regulation of the dc bus voltage in an Active Front-End Converter (AFEC). This paper proposes a two degree-of-freedom type proportional-integral controller (2DOF-PI) for the regulation of dc bus voltage in an AFEC. Such a controller eliminates the left-half plane (LHP) zero in the command-to-output transfer function for dc bus voltage regulation that is inherent to the conventional 1DOF-PI for this application. The dynamic model of an AFEC in the synchronous reference frame (SRF) is presented. An inner current control and outer dc voltage control loop is built for controlling the AFEC. Vector-control scheme is employed to achieve decoupled control of direct-axis and quadrature-axis currents. The outer dc voltage control loop is designed with a 2DOF-PI to complete the control system. Transfer function (TF) of the controller is derived based on the presented model and used to calculate the controller gains. Transient and steady state performance of the designed controllers are investigated in MATLAB/Simulink and results presented.

Thapa, Anup↗