Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “passivation layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Sputter-deposited CdMgTe for rear contact to CdSeTe/CdTe solar cells

CdTe-based photovoltaic device performance improvement is predominantly limited by open-circuit voltage. This work approaches the voltage deficit challenge through the incorporation of a cadmium magnesium telluride (CdMgTe) electron reflector layer at the back of 1.5- μm CdSeTe/CdTe absorbers to reduce back-surface recombination through a conduction band offset. A sputtered CdMgTe electron reflector layer permitted low fabrication temperatures and circumvented the intolerance of CdMgTe to thermal processing present in traditional close-space sublimation (CSS)-deposited CdMgTe devices. Here, we demonstrate that sputtered CdMgTe simultaneously promotes the retention of chlorine passivation and magnesium which is not feasible with CSS fabrication. We also show the importance of the Cu and Te back contact order in CdMgTe devices. Through the optimization of the sputtered CdMgTe substrate temperature, doping, and back structure configuration, 1.5 μm CdSeTe/CdTe devices with a sputtered CdMgTe layer achieved an efficiency of 16.0%, significantly higher than with CSS CdMgTe, and demonstrated partial enactment of electron-reflector behavior.

14 SOLAR ENERGY↗
DOE OSTI2021

Photoelectrochemically Self Improving Si/GaN Photocathode: Figure 4a Raw Data

Calculated formation energy of (0001 ̅) c-plane GaN surfaces. The density-functional theory (DFT) calculations were performed with the generalized gradient approximation, using the plane-wave pseudopotential quantum-ESPRESSO package. Ultrasoft pseudopotentials were used to describe the interaction between valence electrons and ionic cores, where Ga 3d electrons were explicitly treated as valence electrons. The wave functions and electronic density were expanded in a plane-wave basis set truncated at a cutoff energy of 30 Ry and 240 Ry, respectively. The surface was modeled using a repeated slab geometry using a (2×2) unit cell with a thickness of seven GaN bilayers, where the Ga-terminated bottom side was passivated by pseudo-hydrogen with charge of 1.25e. In addition, the (1010) surface was modeled using 8 GaN atomic layers with a lateral dimension of 9.57 Å x 10.38 Å. A vacuum width of at least 15.0 Å was introduced between consecutive slabs, and a k-point mesh of 5x5x1 and 2x2x1 was used to sample the surface Brillouin zone for the polar and non-polar surfaces, respectively. Calculated formation energy of (0001 ̅) c-plane GaN surfaces with different oxygen configuration within the anion and cation-rich limits: ideal GaN surfaces of c-plane and m-plane; configurations with 100% replacement of nitrogen by oxygen on the surface c-plane and m-plane; 100% replacement of nitrogen by oxygen in the subsurface bilayer c-plane and m-plane; and configurations with 50% replacement of nitrogen of the surface and subsurface bilayers by oxygens c-plane and m-plane. In both cases, the ideal surface is chosen as the reference.

photocathode↗
DOE OSTI2021

Photoelectrochemically Self Improving Si/GaN Photocathode: Figure 4b Raw Data

Calculated formation energy of (1010 ̅) m-plane GaN surfaces. The density-functional theory (DFT) calculations were performed with the generalized gradient approximation, using the plane-wave pseudopotential quantum-ESPRESSO package. Ultrasoft pseudopotentials were used to describe the interaction between valence electrons and ionic cores, where Ga 3d electrons were explicitly treated as valence electrons. The wave functions and electronic density were expanded in a plane-wave basis set truncated at a cutoff energy of 30 Ry and 240 Ry, respectively. The surface was modeled using a repeated slab geometry using a (2×2) unit cell with a thickness of seven GaN bilayers, where the Ga-terminated bottom side was passivated by pseudo-hydrogen with charge of 1.25e. In addition, the (1010) surface was modeled using 8 GaN atomic layers with a lateral dimension of 9.57 Å x 10.38 Å. A vacuum width of at least 15.0 Å was introduced between consecutive slabs, and a k-point mesh of 5x5x1 and 2x2x1 was used to sample the surface Brillouin zone for the polar and non-polar surfaces, respectively. Calculated formation energy of (1010 ̅) m-plane GaN surfaces with different oxygen configuration within the anion and cation-rich limits: ideal GaN surfaces of c-plane and m-plane; configurations with 100% replacement of nitrogen by oxygen on the surface c-plane and m-plane; 100% replacement of nitrogen by oxygen in the subsurface bilayer c-plane and m-plane; and configurations with 50% replacement of nitrogen of the surface and subsurface bilayers by oxygens c-plane and m-plane. In both cases, the ideal surface is chosen as the reference.

photocathode↗
DOE OSTI2025

WHYMSIE-SGP Field Campaign Report

Through a partnership between the U.S. National Aeronautics and Space Administration (NASA) and the National Oceanic and Atmospheric Administration (NOAA), this field campaign demonstrated first-of-its-kind hyperspectral microwave airborne measurements (Conical Scanning Millimeter-wave Imaging Radiometer [CoSMIR-H]). It was complemented by other passive (infrared, visible) and active (lidar) sensors onboard the NASA ER-2 aircraft. Serving as a future NASA planetary boundary-layer (PBL) mission prototype, the Westcoast and Heartland Hyperspectral Microwave Intensive Experiment (WH 2 yMSIE, formerly WHyMSIE) aimed to capture a wide variety of thermodynamic, moisture, and PBL regimes across a variety of surface types. The intensive operating period of the campaign spanned from October 22, 2024, through November 15, 2024, and included a large network of collaborators.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1992

Maneuvering technology for advanced fighter aircraft

The need for increased maneuverability has its genesis from the first aerial combat engagement when two adversaries entangled themselves in a deadly aerial dance trying to gain the advantage over the other. It has only been in the past two decades that technologies have been investigated to increase aircraft control at maneuver attitudes that are typically dominated by highly separated flows. These separated flow regions are aggravated by advanced fighter aircraft shapes required to defeat an electronic enemy. This paper discusses passive and active devices that can be used to enhance the maneuverability of advanced fighter aircraft through vortex flow control, boundary layer control, and innovative flow manipulation.

Alexander, Michael G.↗
NASA NTRS1996

The Implementation and Evaluation of the Emergency Response Dose Assessment System (ERDAS) at Cape Canaveral Air Station/Kennedy Space Center

The Emergency Response Dose Assessment System (ERDAS) is a system which combines the mesoscale meteorological prediction model RAMS with the diffusion models REEDM and HYPACT. Operators use a graphical user interface to run the models for emergency response and toxic hazard planning at CCAS/KCS. The Applied Meteorology Unit has been evaluating the ERDAS meteorological and diffusion models and obtained the following results: (1) RAMS adequately predicts the occurrence of the daily sea breeze during non-cloudy conditions for several cases. (2) RAMS shows a tendency to predict the sea breeze to occur slightly earlier and to move it further inland than observed. The sea breeze predictions could most likely be improved by better parameterizing the soil moisture and/or sea surface temperatures. (3) The HYPACT/REEDM/RAMS models accurately predict launch plume locations when RAMS winds are accurate and when the correct plume layer is modeled. (4) HYPACT does not adequately handle plume buoyancy for heated plumes since all plumes are presently treated as passive tracers. Enhancements should be incorporated into the ERDAS as it moves toward being a fully operational system and as computer workstations continue to increase in power and decrease in cost. These enhancements include the following: activate RAMS moisture physics; use finer RAMS grid resolution; add RAMS input parameters (e.g. soil moisture, radar, and/or satellite data); automate data quality control; implement four-dimensional data assimilation; modify HYPACT plume rise and deposition physics; and add cumulative dosage calculations in HYPACT.

Evans, Randolph J.↗
DOE OSTI2022

Facile Surface Coatings for Performance Improvement of NMC811 Battery Cathode Material

High nickel content layered oxide LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) is a promising cathode material with a high theoretical capacity of 200 mAh g -1 for use in high energy density lithium-ion batteries. However, its surface can easily get passivated by LiOH and Li 2 CO 3 due to its surface residual Li 2 O being reacting with ambient moisture and CO 2 . Herein, NMC811 was treated in a 3.0 M solution of lithium bis(fluorosulfonyl)imide (LiFSI) in dimethyl carbonate (DMC) at 60 °C for 8 h, 16 h and 24 h, respectively, resulting in coating of the NMC811 surface with LiF due to the basic nature of those residual lithium salts that react with LiFSI. The facile treatment of NMC811 in LiFSI/DMC not only improves the cycling stability but also enhances the capacity of the Li/NMC811 cells, mainly because of the thinning of the Li 2 CO 3 layer as suggested by cyclic voltammograms and impedance analyses. This method opens a new avenue for activation of passivated NMC811 particles for practical battery applications.

25 ENERGY STORAGE↗
DOE OSTI2022

Multifunctional fiber-reinforced composites for passive sensing and energy harvesting with enhanced mechanical performance

Fiber-reinforced polymer composites (FRPCs) are valid alternatives to metals, especially in the aerospace industry, for their superior strength-to-weight ratio. FRPCs are generally manufactured by stacking layers of fibers and infusing them with epoxy-based adhesives to result in laminates. Such layer-by-layer structure often ensues a poor interlaminar property of the composites. Additionally, FRPCs can sustain complex damage modes because of their inherent anisotropic characteristics. For example, delamination can occur due to low-velocity impact at a subsurface level, which can result in premature catastrophic failures if undetected. Thus, structural monitoring is crucial to identify such damage. Point-based sensors (e.g., strain gauges, accelerometers, among many) can be embedded in the FRPCs for structural monitoring. However, their electrical power demand often embroils their usage. Therefore, the main objective of this research is to design and implement multifunctional composites that can simultaneously perform passive sensing and energy harvesting while exhibiting better mechanical performance. Previous research efforts have demonstrated that a continuous feed-through deposition of functional materials on fiber surfaces simultaneously enhanced the mechanical and sensing properties of the FRPCs. This study explores a similar approach to encode passive sensing and energy harvesting properties in the FRPCs by integrating ferroelectric microparticles on the fiber surfaces. Upon ensuring their superior interlaminar shear strength, sensing and energy harvesting properties were characterized through experimental studies. The outcome is a multifunctional composite fabricated by coating the fibers with functional microparticles through a high throughput, scalable, and low-cost approach that enables passive sensing, energy harvesting, and improved mechanical performance.

Gupta, Sumit↗
NASA NTRS2014

Simulation of Seasonal Snow Microwave TB Using Coupled Multi-Layered Snow Evolution and Microwave Emission Models

The accurate quantification of SWE has important societal benefits, including improving domestic and agricultural water planning, flood forecasting and electric power generation. However, passive-microwave SWE algorithms suffer from variations in TB due to snow metamorphism, difficult to distinguish from those due to SWE variations. Coupled snow evolution-emission models are able to predict snow metamorphism, allowing us to account for emissivity changes. They can also be used to identify weaknesses in the snow evolution model. Moreover, thoroughly evaluating coupled models is a contribution toward the assimilation of TB, which leads to a significant increase in the accuracy of SWE estimates.

microwave↗
DOE OSTI2025

Vertical 2T-nC FeRAM Demonstration: BEOL Read Transistor for 4F 2 Memory Strings and Two-Terminal Selector Design for Polarization Disturb Mitigation

In this work, we demonstrate a vertical 2T-nC FeRAM with a back-end-of-line (BEOL) read transistor (T R ) for 4F 2 string and propose a selector design to mitigate polarization disturb in passive capacitor crossbar arrays. Key contributions include: 1) successful integration and operation composed of a Si MOSFET write transistor (T W ), 3-layer cylindrical ferroelectric capacitors, and Si-doped In 2 O 3 BEOL T R , demonstrating the feasibility of 4F 2 2T−nC string; 2) introducing nonlinearity into the capacitor stack to suppress ferroelectric voltage drop under inhibition biases while maintaining sufficient write voltage, reducing disturbance; 3)modeling and experimental validation of inserting a metalsemiconductor (a-Si)-metal (MSM) selector into the capacitor in mitigating the disturb, particularly achieving 9x reduction of disturb after 10 6 cycles in the V W /2 scheme.

42 ENGINEERING↗
NASA NTRS1983

Viscous thermocapillary convection at high Marangoni number

A liquid, contained in a quarter plane, undergoes steady motion due to thermocapillary forcing on its upper boundary, a free surface separating the liquid from a passive gas. The rigid vertical sidewall has a strip whose temperature is elevated compared with the liquid at infinity. A boudnary-layer analysis is performed that is valid for large Marangoni numbers M and Prandtl numbers P. It is found that the Nusselt number N for the horizontal heat transport satisfies N proportional to min (M to the 1 2/7/power, M to the 1 1/5/power, M to the 1 1/10/power) Generalizations are discussed.

Cowley, S. J.↗
NASA NTRS1998

Making Intercontinental Burning Influences Quantitative: Lessons on Transport and Geochemistry From the 3-D Simulation of CO in PEM-T A and TRACE-A

We report on two aspects of the simulation of global transport of plumes originating from subtropical biomass fires. We use of meteorological assimilation (MM5) at 2-degree resolution with a Grail cloud parameterization and a Blackadar-based planetary boundary layer parameterization. Ames's GRACES model provides emissions, transport, and an appropriate level of simulated chemical transformation. We have worked with passive-tracer CO or linear chemistry. This is appropriate since we find major work to be done in evaluating CO source strengths and transport mechanisms before chemical integrations could be meaningful. First, we present mechanisms by which CO and other pollutants are introduced into the free troposphere, and are then transported with hate dilution from approx. 0 to approx. 180 degrees longitude. One principal conduit for these plumes is the vernal subtropical jet; however the plumes appear at various altitudes and latitudes as they influenced by frontal motions and (most likely) radiative processes. A common, repeated pattern of transport has pollutant plumes arriving in the distant Pacific Ocean from Africa and South America at 25 degrees south and 14 km altitude. Following this, there is then a general appearance of pollution at extending down to 5 kin at more equatorial (10 S) and polar latitudes (to 45 S). Second, we evaluate the quantitative success of our simulation. (Such success requires efforts considerably beyond trajectory analyses, and is necessary for our community to claim an understanding of the effects of biomass burning on global atmospheric chemistry and the planet's trend in oxidizing capacity.) We find that we simulate most pollution episodes sampled by Glenn Sachse's CO instrument and the Blake hydrocarbon analyses during PENT A. We will present our current ideas on why our general levels appear satisfactory when the observations are within 20 ppb of background levels, but substantially miss the variability associated with the most intense biomass burning plumes. As time allows, we will speculate on the origins of a class of plumes that appear in the mid-troposphere, but are missing from our simulations.

Chatfield, Robert↗
NASA NTRS2006

MSFC Analysis of Thermal Control Materials on MISSE

Many different passive thermal control materials were flown as part of the Materials on International Space Station Experiment, including coatings, anodizes, and multi-layer insulation materials. Engineers and scientists at the Marshall Space Flight Center have analyzed a number of these materials, including: Zinc oxide/potassium silicate coating, Zinc orthotitanate/potassium silicate coating, Sulfuric acid anodized aluminum, Various coatings for part marking, automated rendezvous and capture, and astronaut visual aids, FEP Teflon with silver/Inconel backing, and Beta cloth with and without aluminization. These and other material samples were exposed to the low Earth orbital environment of atomic oxygen, ultraviolet radiation, thermal cycling, and hard vacuum, though atomic oxygen exposure was very limited for some samples. Solar absorptance, infrared emittance, and mass measurements indicate the durability of these materials to withstand the space environment. The effect of contamination from an active space station on the performance of white thermal control coatings is discussed.

Finckenor, Miria↗
NASA NTRS2012

Engineered Multifunctional Surfaces for Fluid Handling

Designs incorporating variations in capillary geometry and hydrophilic and/or antibacterial surface properties have been developed that are capable of passive gas/liquid separation and passive water flow. These designs can incorporate capillary grooves and/or surfaces arranged to create linear and circumferential capillary geometry at the micro and macro scale, radial fin configurations, micro holes and patterns, and combinations of the above. The antibacterial property of this design inhibits the growth of bacteria or the development of biofilm. The hydrophilic property reduces the water contact angle with a treated substrate such that water spreads into a thin layer atop the treated surface. These antibacterial and hydrophilic properties applied to a thermally conductive surface, combined with capillary geometry, create a novel heat exchanger capable of condensing water from a humid, two-phase water and gas flow onto the treated heat exchanger surfaces, and passively separating the condensed water from the gas flow in a reduced gravity application. The overall process to generate the antibacterial and hydrophilic properties includes multiple steps to generate the two different surface properties, and can be divided into two major steps. Step 1 uses a magnetron-based sputtering technique to implant the silver atoms into the base material. A layer of silver is built up on top of the base material. Completion of this step provides the antibacterial property. Step 2 uses a cold-plasma technique to generate the hydrophilic surface property on top of the silver layer generated in Step 1. Completion of this step provides the hydrophilic property in addition to the antibacterial property. Thermally conductive materials are fabricated and then treated to create the antibacterial and hydrophilic surface properties. The individual parts are assembled to create a condensing heat exchanger with antibacterial and hydrophilic surface properties and capillary geometry, which is capable of passive phase separation in a reduced gravity application. The plasma processes for creating antibacterial and hydrophilic surface properties are suitable for applications where water is present on an exposed surface for an extended time, such that bacteria or biofilms could form, and where there is a need to manage the water on the surface. The processes are also suitable for applications where only the hydrophilic property is needed. In particular, the processes are applicable to condensing heat exchangers (CHXs), which benefit from the antibacterial properties as well as the hydrophilic properties. Water condensing onto the control surfaces of the CHX will provide the moist conditions necessary for the growth of bacteria and the formation of biofilms. The antibacterial properties of the base layer (silver) will mitigate and prevent the growth of bacteria and formation of biofilms that would otherwise reduce the CHX performance. In addition, the hydrophilic properties reduce the water contact angle and prevent water droplets from bridging between control surfaces. Overall, the hydrophilic properties reduce the pressure drop across the CHX.

Thomas, Chris↗
DOE OSTI2024

Scalable method of fabricating structured polymers for passive daytime radiative cooling and other applications

A switchable light transmission module is disclosed that includes a substrate having a first surface defining at least part of an enclosed volume, a porous layer disposed on the first surface and in fluid communication with the enclosed volume, and a reservoir in fluid communication with the enclosed volume. The reservoir is configured to supply a fluid to the sealed volume such that the fluid contacts the porous layer. The fluid has a refractive index that is close to the refractive index of the porous layer, has a high wettability for the porous layer, and does not dissolve the porous layer. When in a dry state, voids in the porous layer are filled with air which has a much different refractive index than the porous layer itself, resulting in a surface that is reflective and not very transmissive. During wetting of the porous layer by the fluid, however, those voids are filled with the fluid, reducing the difference in refractive index across the polymer-fluid interfaces such that light scattering is negligible and the surface becomes light permeable.

Mandal, Jyotirmoy↗
DOE OSTI2023

High-temperature oxidation behavior of the SiC layer of TRISO particles in low-pressure oxygen

Surrogate tristructural-isotropic (TRISO)-coated fuel particles were oxidized in 0.2 kPa O 2 at 1200–1600°C to examine the behavior of the SiC layer and understand the mechanisms. The thickness and microstructure of the resultant SiO 2 layers were analyzed using scanning electron microscopy, focused ion beam, and transmission electron microscopy. The majority of the surface comprised smooth, amorphous SiO 2 with a constant thickness indicative of passive oxidation. The apparent activation energy for oxide growth was 188 ± 8 kJ/mol and consistent across all temperatures in 0.2 kPa O 2 . The relationship between activation energy and oxidation mechanism is discussed. Raised nodules of porous, crystalline SiO 2 were dispersed across the surface, suggesting that active oxidation and redeposition occurred in those locations. These nodules were correlated with clusters of nanocrystalline SiC grains, which may facilitate active oxidation. So these findings suggest that microstructural inhomogeneities such as irregular grain size influence the oxidation response of the SiC layer of TRISO particles and may influence their accident tolerance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1999

Thermal Control Replacement Materials Evaluated for Durability and Selected for the Hubble Space Telescope

During the Hubble Space Telescope (HST) second servicing mission, astronauts noticed that the outer layer of the multilayer insulation (MLI) was cracked in many locations around the telescope. The insulation s outer layer is composed of 5-mil (0.127 mm) Teflon FEP (DuPont; fluorinated ethylene propylene) with vapor-deposited aluminum (VDA) on the backside. The MLI blankets, which are used on over 80 percent of the external surface of the telescope, provide passive thermal control for equipment. Two large cracks were observed on the light shield directly above the high gain antenna. The upper light shield crack propagated from a cut placed in the blanket during installation around a handrail standoff. Two cracks propagated almost normal to each other, with the outer layer curling tightly as the cracks propagated. A second much larger vertical crack had started to curl and lift away from the telescope, as seen in the figure. MLI on the equipment bays was cracked extensively also, and in some areas it had pulled away from the bay. Continued degradation of the equipment bay insulation would potentially cause limited observations because of housekeeping boxes; for example, the data interface unit could overheat during some portions of the year, in certain sun angles.

deGroh, Kim K.↗
DOE OSTI2020

Visualizing Oxidation Mechanisms in Few-Layered Black Phosphorus via In Situ Transmission Electron Microscopy

Layered two-dimensional (2D) black phosphorus (BP) exhibits novel semiconducting properties including a tunable bandgap and high electron mobility. However, the poor stability of BP in ambient environment severely limits potential for application in future electronic and optoelectronic devices. While passivation or encapsulation of BP using inert materials/polymers has emerged as a plausible solution, a detailed fundamental understanding of BP's reaction with oxygen is imperative to rationally advance its use in applications. Here, we use in situ environmental transmission electron microscopy to elucidate atomistic structural changes in mechanically exfoliated few-layered BP during exposure to varying partial pressures of oxygen. An amorphous oxide layer is seen on the actively etching BP edges, and the thickness of this layer increases with increasing oxygen partial pressure, indicating that oxidation proceeds via initial formation of amorphous P x O y species which sublime to result in the etching of the BP crystal. We observe that while few-layered BP is stable under the 80 kV electron beam (e-beam) in vacuum, the lattice oxidizes and degrades at room temperature in the presence of oxygen only in the region under the e-beam. The oxidative etch rate also increases with increasing e-beam dosage, suggesting the presence of an energy barrier for the oxidation reaction. Preferential oxidative etching along the [0 0 1] and [0 0 1] crystallographic directions is observed, in good agreement with density functional theory calculations showing favorable thermodynamic stability of the oxidized BP (0 0 $\bar{1}$) planes compared to the (1 0 0) planes. Finally, we expect the atomistic insights and fundamental understanding obtained here to aid in the development of novel approaches to integrate BP in future applications.

2D materials↗