Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effect of Re and Al additions on the microstructure and mechanical properties of Nb-18Ti-12W alloy

Microstructure and mechanical properties at 25–1200 °C of new refractory alloys, Nb-18Ti-12W (NTW), Nb-18Ti-12W-5Re (NTW-R) and Nb-18Ti-12W-5Re-1Al (NTW-RA), all compositions are in atomic percent, are reported. The alloys are developed as an alternative to a denser, more expensive and difficult-to-process refractory alloy WC-3009. After production by arc melting and hot isostatic pressing at 1400 °C, 207 MPa for 3 h, the alloys have a BCC crystal structure with the average grain size of ~150–200 μm and contain low volume fraction of (Ti,N)-rich precipitates near grain boundaries. NTW shows excellent malleability at all studied temperatures. Its yield stress at 25 °C, 1000 °C and 1200 °C is 874 MPa, 353 MPa and 202 MPa, respectively. The NTW-R and NTW-RA alloys are stronger at all the studied temperatures; however, they lack in compression ductility at 25 °C. As a result, extensive deformation twinning and formation of intergranular voids precede the fracture of these two alloys at 25 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Correlation between Interface Microstructure and Bond Strength of Al6061/Al6061 HIP-Bonded Plates for Fuel Cladding Application

The effects of hot isostatic pressing (HIP) processing parameters on microstructure and bond strength of Al6061/Al6061 plate interfaces were systemically investigated at the micro- and nanoscale. The HIP bonding of the two aluminum plates was performed at four temperatures: 350°C, 400°C, 450°C, and 560°C. The results reveal the formation of micron scaled Mg 2 Si precipitate and uniform nano scaled Mg 2 Al 2 O 5 oxide at the interface. The formation of Mg 2 Al 2 O 5 is closely associated with the fast bulk diffusion of Mg from the Al matrix to the amorphous Al 2 O 3 /Al interface and subsequent reaction between Mg and Al 2 O 3 . Finally, the highest and lowest bond strengths were observed in samples HIP bonded at 450°C and 350°C, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chain rigidity controlled aggregation ability and solid-state microstructures for efficient stretchable conjugated polymer films

Stretchable conjugated polymer films with good electrical performance under mechanical deformation are highly desirable for soft electronics. However, the mechanical and electrical properties of these films, particularly in conjugated polymer:elastomer blends, are not fully understood at molecular level. Here, this study explores the relationships among molecular structure, aggregation ability, film microstructure, and the electrical/mechanical properties of three diketopyrrolopyrrole-based conjugated polymers (P1, P2, P3) with decreasing backbone rigidity and their corresponding polymer:elastomer blends. The most flexible polymer P3 shows strong aggregation, which forms highly crystalline fibers to produce fragile neat film and produces large isolated crystallites restricting charge transport in blend film. As chain rigidity increases, the P1 and P2 polymers show weaker aggregation, and produce smaller crystallites in neat films with enhanced ductility. P1 and P2 based blend films display nanocrystallites polymer networks with dispersed elastomer domains. As a result, we achieved near-constant charge mobility before and after stretching under 50 % strain for P2-based blend films with well-controlled pathways for both charge transport and energy dissipation. This study demonstrates the critical role of backbone rigidity in regulating the properties of stretchable conjugated polymer films, paving the way for more reliable and deformable materials in soft electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Reverse scaling of a bonded-sphere DEM model: Formulation and application to lignocellulosic biomass microstructures

We explore scaling laws for adapting a bonded-sphere discrete element method (BS-DEM) model developed for woody structural mechanics at the millimeter scale to model the mechanics of realistic lignocellulosic biomass microstructures. Two scaling approaches, i.e., the reverse coarse graining (RCG) and equivalent bulk behavior (EBB), are proposed based on the classical mechanics principles and assessed in the single-particle compression and rectangular cuboid block tension tests. The EBB approach is recommended for BS-DEM models with general 3D geometries and is applied to simulate the microindentation test on a realistic microscale pinewood specimen. Simulations are performed to elucidate the impact of specimen thickness and loading position on the specimen’s force–deformation behavior. Furthermore, the range of Young’s modulus obtained from the calibrated BS-DEM simulations can match the experimental measurements. This is the first-of-its-kind study that has explored scale-bridging modeling approaches in biomass micromechanics and has proposed solutions based on BS-DEM models in the microscale.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

On the quantitative characterization of weld microstructures

Here, a new technique to quantify grain shape and grain boundary curvature in the fusion zone (FZ) and the heat-effected zone (HAZ) of refractory metals and alloys has been developed. The application of this technique to quantify the effect of welding speed on these microstructural characteristics in simulated molybdenum welds is highlighted in this study. A 50% increase in weld speed more than doubles the fraction of grain segments in the fusion zone with orientations between 00 to 300 to the normal to the welding direction, with a corresponding 50% decrease in the fraction of grain segments oriented along the welding direction. This increase in weld speed also results in a reduction in grain size from approximately 120 µm to 84 µm along the WD at the FZ centerline. Grain boundary curvature is negative near the weld centerline and the edge of the fusion zone, indicating that with increasing distance from the weld centerline, the grain segments progressively rotate towards a direction normal to the welding direction at both locations. Presence of regions with relatively straight grain segments indicated by curvatures close to zero were identified in between the weld centerline and the edge of the FZ at all weld speeds.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Scalable Solution-Processed Electrolyte Membranes with Optimized Microstructure for High-Performance Protonic Ceramic Electrochemical Cells

Proton-conducting electrochemical cells (PCECs) are promising for efficient hydrogen production, but achieving dense, uniform, thin electrolyte layers remains a key challenge, particularly for scalable fabrication. Here, we present a solution-processed deposition approach with a mechanistically optimized slurry for uniform electrolyte formation. By tailoring particle size distribution, solid loading, and solvent/additive balance, we regulated wetting behavior and evaporation kinetics of the electrolyte slurry to promote homogeneous electrolyte particle packing. These features facilitate tight grain boundary contact and early stage neck growth during sintering, eliminating residual porosity, and improving mechanical integrity. The resulting ∼15 μm thick electrolyte shows high density, strong electrode adhesion, and stable interfaces outperforming the previously reported spray-based fabricated electrolyte by about 31% at 600 °C in FC mode. Single cells deliver 0.962 W cm –2 at 600 °C in fuel cell mode and 1.31 A cm –2 at 1.3 V in electrolysis mode, maintaining robust performance over 100 h with negligible degradation (≤0.02% h –1 ) in each mode. Scale-up to 2.5 cm diameter substrates confirmed reproducible densification and geometric stability. This work demonstrates a cost-effective, scalable route where control over particle-fluid interactions and drying dynamics enables a superior electrolyte microstructure and high PCEC performance.

dense microstructure↗
DOE OSTI2025

Revealing the evolution of order in materials microstructures using multi-modal computer vision

The development of high-performance materials for microelectronics, energy storage, and extreme environments depends on our ability to describe and direct property-defining microstructural order. Our present understanding is typically derived from laborious manual analysis of imaging and spectroscopy data, which is difficult to scale, challenging to reproduce, and lacks the ability to reveal latent associations needed for mechanistic models. Here, we demonstrate a multi-modal machine learning (ML) approach to describe order from electron microscopy analysis of the complex oxide La 1−x Sr x FeO 3 . We construct a hybrid pipeline based on fully and semi-supervised classification, allowing us to evaluate both the characteristics of each data modality and the value each modality adds to the ensemble. We observe distinct differences in the performance of uni- and multi-modal models, from which we draw general lessons in describing crystal order using computer vision.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Demonstration of and future perspective on scaling ultrafast-laser-ablation microstructuring of Li-ion battery electrodes to roll-to-roll production and large-format cells

This work demonstrates integration of an ultrafast laser onto a roll-to-roll machine, the laser structuring of a double-sided, 700 m long roll of graphite battery anode and its subsequent manufacture into 27 Ah prismatic cells. The electrode was ablated with a novel hybrid-microstructure composed of both hexagonally arranged pores for enhanced rate performance and channels for fast electrolyte wetting. Subsequently, this anode and a non-ablated baseline anode are paired with an NMC111 cathode for cell building and electrochemical characterization. Compared to the baseline, laser ablated cells demonstrated a reduction in soaking time of at least 60%, an improvement in fast charge capability with >30% more capacity accepted during 6C charging, and an extension of cycle life of >40% during 0.5C cycling. Further, a perspective is provided on scaling ultrafast laser ablation of battery electrodes to industrial throughputs. Additionally, lessons learned from this pilot-scale demonstration are provided in regards to optical architecture, debris removal, and system control. A techno-economic analysis is used to demonstrate that laser ablation can be integrated into existing electrode manufacturing facilities with only ≈$\$$1.3 per kWh increase (≈2%) in manufacturing cost. Preemptive electrode design for laser ablation is discussed as a further method for enhancing performance. Finally, an analysis of available laser systems and beam-scanning architectures is used to determine design requirements to scale process throughput to a state-of-the-art speed of 50 m min −1 . This analysis demonstrates that laser ablating Li-ion battery electrodes has multiple benefits to manufacturing and battery performance, that the technology already exists to achieve high laser-ablation throughputs, and that integrating ultrafast laser ablation to electrode manufacturing will not create a cost or processing bottleneck.

25 ENERGY STORAGE↗
DOE OSTI2020

Numerical simulation of dispersion and nonlinear characteristics of microstructured silica fibres with a thin suspended core in a wide range of their parameters

Dispersion and nonlinear characteristics of microstructured silica fibres with a thin suspended core surrounded by three, four or six air holes have been studied theoretically in the wavelength range 1 – 2 μm. It has been shown that, owing to strong fundamental mode confinement near the core, the Kerr nonlinearity coefficient can exceed the nonlinearity coefficient of standard telecom fibre SMF28e by two orders of magnitude. The large waveguide contribution allows for effective group velocity dispersion management. Estimates are presented that demonstrate the feasibility of using suspended core fibre exhibiting Kerr nonlinearity for generating non-classical light: a state with squeezed quantum fluctuations in one of the quadrature components of a cw laser signal at a wavelength near 1.55 μm. (paper)

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure and creep strength of simulated intercritical heat-affected zone of grade 91 steel

The intercritical heat affected zone (ICHAZ) has been reported as one of the most Type IV cracking susceptible regions in 9Cr creep-resistant steel weldments. However, creep degradation mechanisms within the ICHAZ itself need further clarifications. In this work, two ICHAZ specimens of Grade 91 steel, low-temperature ICHAZ (LT-ICHAZ) and high-temperature ICHAZ (HT-ICHAZ), were simulated using the Gleeble thermomechanical system by exposing to two peak temperatures (860 °C and 900 °C) between $A_{C1}$ and $A_{C3}$. Dramatically different creep strengths of two simulated ICHAZs were observed and studied. We report dilation curve analysis indicates a high fraction of newly transformed martensite formed in the HT-ICHAZ, which results in a much higher hardness (360 HV0.5) of the HT-ICHAZ than 266 HV0.5 of LT-ICHAZ. Precipitates, especially $M_{23}C_6$ carbides, were not fully dissolved in both ICHAZ specimens. After a typical postweld heat treatment (760 °C-2 hours), the faster recovery of low-carbon martensite and reduced precipitation strengthening due to $M_{23}C_6$ carbides coarsening in the HT-ICHAZ led to a significant hardness reduction. These microstructural degradations in the HT-ICHAZ made its creep lifetime about 36 times shorter than that of the LT-ICHAZ tested at 650 °C. The remaining tempered martensite from base metal in the LT-ICHAZ was the primary contributor to maintain its high creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Prediction of microstructure formation in laser powder bed fusion process.

The datasets are results analyzing the predicted microstructures in a single track during the laser powder bed fusion additive manufacturing process. They are the outputs by running the opensource code, muMatScale (The code can be cited at: Yuan, Lang, Fattebert, Jean-Luc, and Sabau, Adrian. (2023, August 03). muMatScale. [Computer software]. https://github.com/lang-yuan/muMatScale. https://doi.org/10.11578/dc.20240112.2.) For each set of data, it contains the time-dependent information of Temperature, Fraction Solid, Grain ID, Grain Angle ( crystallographic orientations by Euler angles), and solute Composition. The dataset can be visualized by Paraview (https://www.paraview.org/ ). The 6 datasets are: 1. Baseline_base1_n4e14_dt20: baseline case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 2. Nuc_n4e15_dt20: case with bulk nucleation density of 4E+15/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 3. Nuc_n4e15_dt50: case with bulk nucleation density of 4E+15/m^3, undercooling of 50K, substrate nucleation density of 1.5E+15/m^3 4. Nuc_n6e15_dt20: case with bulk nucleation density of 4E+16/m^3, undercooling of 20K, substrate nucleation density of 1.5E+15/m^3 5. Base4_n4e14_dt20: case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 6.0E+15/m^3 6. Base16_n4e14_dt20: case with bulk nucleation density of 4E+14/m^3, undercooling of 20K, substrate nucleation density of 2.4E+16/m^3

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of Microstructural Bands on the Localized Corrosion of Laser Surface-melted 316L Stainless Steel

The localized corrosion of laser surface melted (LSM) 316L stainless steel is investigated by a combination of potentiodynamic anodic polarization in 0.1M HCl and microscopic investigation of the initiation and propagation of localized corrosion. The pitting potential of LSM 316L is significantly lower than the pitting potential of wrought 316L. The LSM microstructure is highly banded as a consequence of the high laser power density and high linear energy density. The bands are composed of zones of changing modes of solidification, cycling between very narrow regions of primary austenite solidification and very wide regions of primary ferrite solidification. Pits initiate in the outer edge of each band where the mode of solidification is primary austenite plane front solidification and primary austenite cellular solidification. The primary austenite regions have low chromium concentration (and possibly low molybdenum concentration), which explains their susceptibility to pitting corrosion. The ferrite is enriched in chromium, which explains the absence of pitting in the primary ferrite regions. The presence of the low chromium regions of primary austenite solidification explains the lower pitting resistance of LSM 316L relative to wrought 316L. The influence of banding on localized corrosion is applicable to other rapidly solidified processes such as additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Assessment of Weld Microstructure Through Sound Velocity Measurements for Power Plant Applications

Here, this research study employed an immersion-based micro-resolution ultrasonic velocity measurement technique (MUVT) to evaluate Grade 91 (9Cr-1Mo-V) steel welds. This process utilized a 20 MHz focused ultrasonic beam with a spot size of 250 µm, a 6 µm laser vibrometer spot size for detection, and an automated 3-axis raster scanner to accurately collect ultrasonic velocity data from two Grade 91 steel welds fabricated using cold metal transfer (CMT) and flux-cored arc welding (FCAW) processes. By analyzing the MUVT data, the Poisson’s ratio (υ) and modulus of elasticity (E), which are important mechanical properties for weldments, were calculated. The correlation between mechanical properties and ultrasonic velocity was examined. The results indicated that longitudinal ultrasonic velocity could effectively identify base metal, heat-affected zone (HAZ), and weld metal areas, showing a strong correlation with hardness. In particular, the distinctive V-shaped dip in velocity and hardness data across the HAZ areas of both samples highlighted changes in the microstructure of creep strength–enhanced ferritic steel welds. Importantly, the immersion-based MUVT demonstrated high accuracy in small sections of the weld, surpassing the conventional contact ultrasonic testing method in spatial resolution detection.

arc welding↗
DOE OSTI2020

Microstructure, Texture, and Strength Development during High-Pressure Torsion of CrMnFeCoNi High-Entropy Alloy

The equiatomic face-centered cubic high-entropy alloy CrMnFeCoNi was severely deformed at room and liquid nitrogen temperature by high-pressure torsion up to shear strains of about 170. Its microstructure was analyzed by X-ray line profile analysis and transmission electron microscopy and its texture by X-ray microdiffraction. Microhardness measurements, after severe plastic deformation, were done at room temperature. It is shown that at a shear strain of about 20, a steady state grain size of 24 nm, and a dislocation density of the order of 1016 m−2 is reached. The dislocations are mainly screw-type with low dipole character. Mechanical twinning at room temperature is replaced by a martensitic phase transformation at 77 K. The texture developed at room temperature is typical for sheared face-centered cubic nanocrystalline metals, but it is extremely weak and becomes almost random after high-pressure torsion at 77 K. The strength of the nanocrystalline material produced by high-pressure torsion at 77 K is lower than that produced at room temperature. The results are discussed in terms of different mechanisms of deformation, including dislocation generation and propagation, twinning, grain boundary sliding, and phase transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Influence of Spatter on Porosity, Microstructure, and Corrosion of Additively Manufactured Stainless Steel Printed Using Different Island Size

Specimens of 316 L stainless steel were printed using laser powder bed fusion (LPBF), a popular metal additive manufacturing (AM) technique, with varying island sizes. Not many researchers have considered the impact of spatter while optimizing LPBF printing parameters. In this research, the influence of spatter was considered while also investigating the effect of varied island size on the microstructure, surface roughness, microhardness, and corrosion resistance of LPBF-316 L. No correlation was observed between surface roughness or microhardness and minor variations in island size. However, a correlation was drawn between varied island sizes and porosity in LPBF-316 L. The specimens associated with larger island sizes showed significantly enhanced corrosion resistance due to fewer manufacturing defects and reduced porosity, attributed to the minimal influence of the spatter. Based on analysis, the LPBF parameters were revised, which lead to superior corrosion resistance of LPBF-316 L, attributed to high density and reduced porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural Assessment of a Multiple-Intermetallic-Strengthened Aluminum Alloy Produced from Gas-Atomized Powder by Hot Extrusion and Friction Extrusion

An aluminum (Al) matrix with various transition metal (TM) additions is an effective alloying approach for developing high-specific-strength materials for use at elevated temperatures. Conventional fabrication processes such as casting or fusion-related methods are not capable of producing Al–TM alloys in bulk form. Solid phase processing techniques, such as extrusion, have been shown to maintain the microstructure of Al–TM alloys. In this study, extrusions are fabricated from gas-atomized aluminum powders (≈100–400 µm) that contain 12.4 wt % TM additives and an Al-based matrix reinforced by various Al–Fe–Cr–Ti intermetallic compounds (IMCs). Two different extrusion techniques, conventional hot extrusion and friction extrusion, are compared using fabricating rods. During extrusion, the strengthening IMC phases were extensively refined as a result of severe plastic deformation. Furthermore, the quasicrystal approximant IMC phase (70.4 wt % Al, 20.4 wt % Fe, 8.7 wt % Cr, 0.6 wt % Ti) observed in the powder precursor is replaced by new IMC phases such as Al3.2Fe and Al45Cr7-type IMCs. The Al3Ti-type IMC phase is partially dissolved into the Al matrix during extrusion. The combination of linear and rotational shear in the friction extrusion process caused severe deformation in the powders, which allowed for a higher extrusion ratio, eliminated linear voids, and resulted in higher ductility while maintaining strength comparable to that resulting from hot extrusion. Results from equilibrium thermodynamic calculations show that the strengthening IMC phases are stable at elevated temperatures (up to ≈ 600 °C), thus enhancing the high-temperature strength of the extrudates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Elaboration of Metallic Materials by SPS: Processing, Microstructures, Properties, and Shaping

After a few decades of increasing interest, spark plasma sintering (SPS) has now become a mature powder metallurgy technique, which allows assessing its performances toward fabricating enhanced materials. Here, the case of metals and alloys will be presented. The main advantage of SPS lies in its rapid heating capability enabled by the application of high intensity electric currents to a metallic powder. This presents numerous advantages balanced by some limitations that will be addressed in this review. The first section will be devoted to sintering issues, with an emphasis on the effect of the electric current on the densification mechanisms. Then, typical as-SPS microstructures and properties will be presented. In some cases, they will be compared with that of materials processed by conventional techniques. As such, examples of nanostructured materials, intermetallics, metallic glasses, and high entropy alloys, will be presented. Finally, the implementation of SPS as a technique to manufacture complex, near-net shape industrial parts will be discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Study of Mechanical Properties, Microstructure, and Residual Stresses of AISI 304/304L Stainless Steel Submerged Arc Weld for Spent Fuel Dry Storage Systems

The confinement boundaries of spent nuclear fuel (SNF) canisters are typically fusion welded. Welded microstructures, strain hardening, and residual stresses combined with a chemically aggressive, chloride-rich environment led to concerns that the welded canister may be susceptible to chloride-induced stress corrosion cracking (CISCC). A comprehensive understanding of the modification of stainless steel (SS) metallurgical and mechanical properties by fusion welding could accelerate the predictive analysis of CISCC susceptibility. This paper describes a submerged arc welding (SAW) procedure that was developed and qualified on 12.7 mm (0.5 in.) thick AISI 304/304L SS to produce joints in a way similar to actual SNF canister manufacturing. This procedure has the potential to reduce the production cost and weld CISCC susceptibility by using fewer welding passes and lower heat input than current industrial applications. Global and local mechanical behaviors and properties, as well as residual stress distributions on the welded joint, were studied. The results indicate that hardness values in the fusion zone (FZ) and heat-affected zone (HAZ) are slightly higher than that of the base metal. Strain localization was presented in the HAZ before the tensile stress reached its maximum value, and then it shifted to the FZ. The specimen finally broke in the FZ. High tensile residual stresses exhibited in the FZ and the nearby HAZ suggest the highest CISCC-susceptible spots. The maximum tensile residual stresses were along the welding direction, indicating that if cracks occur, they would be perpendicular to the welding direction. This study involved developing and qualifying a SAW procedure for SNF canister production. The new procedure yielded cost savings (SAW working efficiency increased by about 80%), improved mechanical properties, and presented moderate residual stresses. Analysis revealed that the welded joint’s low-stress and high-stress damage assessments may be affected by shifts in the strain localization spot under loading.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗