Results for “metallic components” — Page 42

NASA NTRS2014

Modeling of Commercial Turbofan Engine With Ice Crystal Ingestion: Follow-On

The occurrence of ice accretion within commercial high bypass aircraft turbine engines has been reported under certain atmospheric conditions. Engine anomalies have taken place at high altitudes that have been attributed to ice crystal ingestion, partially melting, and ice accretion on the compression system components. The result was degraded engine performance, and one or more of the following: loss of thrust control (roll back), compressor surge or stall, and flameout of the combustor. As ice crystals are ingested into the fan and low pressure compression system, the increase in air temperature causes a portion of the ice crystals to melt. It is hypothesized that this allows the ice-water mixture to cover the metal surfaces of the compressor stationary components which leads to ice accretion through evaporative cooling. Ice accretion causes a blockage which subsequently results in the deterioration in performance of the compressor and engine. The focus of this research is to apply an engine icing computational tool to simulate the flow through a turbofan engine and assess the risk of ice accretion. The tool is comprised of an engine system thermodynamic cycle code, a compressor flow analysis code, and an ice particle melt code that has the capability of determining the rate of sublimation, melting, and evaporation through the compressor flow path, without modeling the actual ice accretion. A commercial turbofan engine which has previously experienced icing events during operation in a high altitude ice crystal environment has been tested in the Propulsion Systems Laboratory (PSL) altitude test facility at NASA Glenn Research Center. The PSL has the capability to produce a continuous ice cloud which is ingested by the engine during operation over a range of altitude conditions. The PSL test results confirmed that there was ice accretion in the engine due to ice crystal ingestion, at the same simulated altitude operating conditions as experienced previously in flight. The computational tool was utilized to help guide a portion of the PSL testing, and was used to predict ice accretion could also occur at significantly lower altitudes. The predictions were qualitatively verified by subsequent testing of the engine in the PSL. In a previous study, analysis of select PSL test data points helped to calibrate the engine icing computational tool to assess the risk of ice accretion. This current study is a continuation of that data analysis effort. The study focused on tracking the variations in wet bulb temperature and ice particle melt ratio through the engine core flow path. The results from this study have identified trends, while also identifying gaps in understanding as to how the local wet bulb temperature and melt ratio affects the risk of ice accretion and subsequent engine behavior.

Jorgenson, Philip C. E.↗

NASA NTRS2014

Modeling of Commercial Turbofan Engine with Ice Crystal Ingestion; Follow-On

The occurrence of ice accretion within commercial high bypass aircraft turbine engines has been reported under certain atmospheric conditions. Engine anomalies have taken place at high altitudes that have been attributed to ice crystal ingestion, partially melting, and ice accretion on the compression system components. The result was degraded engine performance, and one or more of the following: loss of thrust control (roll back), compressor surge or stall, and flameout of the combustor. As ice crystals are ingested into the fan and low pressure compression system, the increase in air temperature causes a portion of the ice crystals to melt. It is hypothesized that this allows the ice-water mixture to cover the metal surfaces of the compressor stationary components which leads to ice accretion through evaporative cooling. Ice accretion causes a blockage which subsequently results in the deterioration in performance of the compressor and engine. The focus of this research is to apply an engine icing computational tool to simulate the flow through a turbofan engine and assess the risk of ice accretion. The tool is comprised of an engine system thermodynamic cycle code, a compressor flow analysis code, and an ice particle melt code that has the capability of determining the rate of sublimation, melting, and evaporation through the compressor flow path, without modeling the actual ice accretion. A commercial turbofan engine which has previously experienced icing events during operation in a high altitude ice crystal environment has been tested in the Propulsion Systems Laboratory (PSL) altitude test facility at NASA Glenn Research Center. The PSL has the capability to produce a continuous ice cloud which is ingested by the engine during operation over a range of altitude conditions. The PSL test results confirmed that there was ice accretion in the engine due to ice crystal ingestion, at the same simulated altitude operating conditions as experienced previously in flight. The computational tool was utilized to help guide a portion of the PSL testing, and was used to predict ice accretion could also occur at significantly lower altitudes. The predictions were qualitatively verified by subsequent testing of the engine in the PSL. In a previous study, analysis of select PSL test data points helped to calibrate the engine icing computational tool to assess the risk of ice accretion. This current study is a continuation of that data analysis effort. The study focused on tracking the variations in wet bulb temperature and ice particle melt ratio through the engine core flow path. The results from this study have identified trends, while also identifying gaps in understanding as to how the local wet bulb temperature and melt ratio affects the risk of ice accretion and subsequent engine behavior.

Jorgenson, Philip C. E.↗

NASA NTRS1995

Predicting engine parameters using the optic spectrum of the space shuttle main engine exhaust plume

The Optical Plume Anomaly Detection (OPAD) system is under development to predict engine anomalies and engine parameters of the Space Shuttle's Main Engine (SSME). The anomaly detection is based on abnormal metal concentrations in the optical spectrum of the rocket plume. Such abnormalities could be indicative of engine corrosion or other malfunctions. Here, we focus on the second task of the OPAD system, namely the prediction of engine parameters such as rated power level (RPL) and mixture ratio (MR). Because of the high dimensionality of the spectrum, we developed a linear algorithm to resolve the optical spectrum of the exhaust plume into a number of separate components, each with a different physical interpretation. These components are used to predict the metal concentrations and engine parameters for online support of ground-level testing of the SSME. Currently, these predictions are labor intensive and cannot be done online. We predict RPL using neural networks and give preliminary results.

Srivastava, Ashok N.↗

DOE OSTI2025

The DESI Y1 RR Lyrae catalog I: Empirical modeling of the cyclic variation of spectroscopic properties and a chemodynamical analysis of the outer halo

We present the catalog of RR Lyrae stars observed in the first year of operations of the Dark Energy Spectroscopic Instrument (DESI) survey. This catalog contains 6,240 RR Lyrae stars out to $\sim100$ kpc from the Galactic center and over 12,000 individual epochs with homogeneously-derived stellar atmospheric parameters. We introduce a novel methodology to model the cyclical variation of the spectroscopic properties of RR Lyrae from single-epoch measurements. We employ this method to infer the radial velocity and effective temperature variation of fundamental mode and first-overtone RR Lyrae stars and to determine their systemic velocities and mean temperatures. For fundamental mode pulsators, we obtain radial velocity curves with amplitudes of $\sim$30--50 km s$^{-1}$ and effective temperature curves with 300--1,000 K variations, whereas for first-overtone pulsators these amplitudes are $\sim20$ km s$^{-1}$ and $\sim 600$ K, respectively. We use our sample to study the metallicity distribution of the halo and its dependence on Galactocentric distance ($R_{\rm GC}$). Using a radius-dependent mixture model, we split the data into chemodynamically distinct components and find that our inner halo sample ($R_{\rm GC}\lesssim50$ kpc) is predominantly composed of stars with [Fe/H] $\sim-1.5$ dex and largely radial orbits (with an anisotropy parameter $\beta\sim0.94$), that we associate with the Gaia-Sausage-Enceladus merger event. Stars in the outer halo field exhibit a broader and more metal-poor [Fe/H] distribution with more circular orbits ($\beta\sim0.39$). The metallicity gradient of the metal-rich and the metal-poor components is found to be $0.005$ and $0.010$ dex kpc$^{-1}$, respectively. Our catalog highlights DESI's tantalizing potential for studying the Milky Way and the pulsation properties of RR Lyrae stars in the era of large spectroscopic surveys.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1985

The kinematics of cool metal-line white dwarfs and accretion in the local interstellar medium

The data base of spectroscopically identified white dwarfs is used to isolate a sample of cool degenerates with trace metals. The spatial distribution and space velocity components of the white dwarfs projected onto and perpendicular to the galactic plane are compared with the distribution of local interstellar hydrogen. The results are consistent with the metals having been accreted during recent encounters with local density enhancements. However, the limited availability of radial velocities, coupled with uncertainties in the derived abundances, the diffusion times, and in the three-dimensional structure of the local medium, prevent a definitive test of the accretion hypothesis at this time.

Aannestad, P. A.↗

DOE OSTI2021

Design rules for 316H nuclear components cladded with nickel or tungsten

The existing Class A metallic materials qualified in the ASME Boiler & Pressure Vessel Code Section III, Division 5 rules for high temperature nuclear reactors are not ideally suited for long term molten salt corrosion resistance in high temperature molten salt reactors. Potentially, corrosion or corrosion driven environmentally assisted cracking could limit the design life of structural components in molten salt reactors. A solution to this limitation is the use of cladded components – overlay the Class A material with a thin layer of some non-qualified, corrosion-resistant material. However, this necessitates the development of design methods for cladded components that do not require long-term testing of clad materials in order to support the near-term deployment of molten salt reactors. This report develops such a methodology along with a complete set of rules presented in a format compatible with an ASME nuclear Code Case. These design rules are for 316H Class A components cladded with either nickel or tungsten. The report also discusses the development of a set of general criteria for selecting clad materials beyond the specific 316H/tungsten and 316H/nickel systems and general acceptance tests for checking the mechanical integrity of the clad/base metal interface. Finally, the report includes a set of fully-documented sample problems detailing the application of the rules to high temperature cladded components

36 MATERIALS SCIENCE↗

DOE OSTI2026

Mechanical behaviour of additively manufactured metals

Additive manufacturing is reshaping the production of engineering components in diverse industries, such as the automotive, aerospace, defense, and biomedical sectors, by offering unprecedented design flexibility. The non-equilibrium processing conditions of additive manufacturing generate materials with unique microstructures and tailored mechanical properties that are often unattainable through conventional routes. This review focuses on recent advances in additively manufactured metals that demonstrate distinctive mechanical behaviors, including strength-ductility synergy, microstresses and gradient plasticity, fracture and fatigue resistance, and high-temperature creep performance. Here, we examine the mechanisms and micromechanical effects arising from the heterogeneous microstructures fabricated by additive manufacturing, to guide the design of a wide range of high-performance structural materials. Furthermore, we discuss critical research needs and emerging opportunities in process control, alloy design, advanced characterization, high-fidelity computational modeling, and machine learning aimed at achieving exceptional mechanical properties in additively manufactured metals.

Additive Manufacturing↗

NASA NTRS1979

The composition and origin of metal in howardites

The metal compositions of howardite breccias are examined and the significance of variations in metal content to meteorite origins is discussed. It is shown that metals in howardites are found primarily in Ni-poor components, associated with primary clasts and similar in composition to pristine lunar anorthosite metal, and in Ni-rich grains, associated with glassy melt rocks and possibly derived from the projectiles which caused the melting. Variations in primary clast metal compositions among the howardite and the identities of matrix and clast metal contents within many howardites suggest that each howardite is derived from a distinct source region. Evidence of thermal metamorphism in Petersburg is interpreted as the results of deeper burial than in other howardites.

Hewins, R. H.↗

NASA NTRS2003

Packaging Technology Designed, Fabricated, and Assembled for High-Temperature SiC Microsystems

A series of ceramic substrates and thick-film metalization-based prototype microsystem packages designed for silicon carbide (SiC) high-temperature microsystems have been developed for operation in 500 C harsh environments. These prototype packages were designed, fabricated, and assembled at the NASA Glenn Research Center. Both the electrical interconnection system and the die-attach scheme for this packaging system have been tested extensively at high temperatures. Printed circuit boards used to interconnect these chip-level packages and passive components also are being fabricated and tested. NASA space and aeronautical missions need harsh-environment, especially high-temperature, operable microsystems for probing the inner solar planets and for in situ monitoring and control of next-generation aeronautical engines. Various SiC high-temperature-operable microelectromechanical system (MEMS) sensors, actuators, and electronics have been demonstrated at temperatures as high as 600 C, but most of these devices were demonstrated only in the laboratory environment partially because systematic packaging technology for supporting these devices at temperatures of 500 C and beyond was not available. Thus, the development of a systematic high-temperature packaging technology is essential for both in situ testing and the commercialization of high-temperature SiC MEMS. Researchers at Glenn developed new prototype packages for high-temperature microsystems using ceramic substrates (aluminum nitride and 96- and 90-wt% aluminum oxides) and gold (Au) thick-film metalization. Packaging components, which include a thick-film metalization-based wirebond interconnection system and a low-electrical-resistance SiC die-attachment scheme, have been tested at temperatures up to 500 C. The interconnection system composed of Au thick-film printed wire and 1-mil Au wire bond was tested in 500 C oxidizing air with and without 50-mA direct current for over 5000 hr. The Au thick-film metalization-based wirebond electrical interconnection system was also tested in an extremely dynamic thermal environment to assess thermal reliability. The I-V curve1 of a SiC high-temperature diode was measured in oxidizing air at 500 C for 1000 hr to electrically test the Au thick-film material-based die-attach assembly.

Chen, Liang-Yu↗

DOE OSTI2023

Electrocatalyst for water electrolysis

A cathode is provided for electrolysis of water wherein the cathode material comprises a multi-principal element, transition metal dichalcogenide material that has four or more chemical elements and that is a single phase, solid solution. The pristine cathode material does not contain platinum as a principal (major) component. However, a cathode comprising a transition metal dichalcogenide having platinum (Pt) nanosized islands or precipitates disposed thereon is also provided.

Balema, Viktor↗

DOE OSTI2022

Metal–Organic Frameworks with Zero and Low–Valent Metal Nodes Connected by Tetratopic Phosphine Ligands

Metal–organic frameworks (MOFs) constructed with M 0 nodes are attractive targets due to the reactivity of these low-valent metals, but examples of these MOFs remain exceedingly rare. The rational design of three-dimensional MOFs with Pd 0 and Pt 0 nodes using tetratopic phosphine ligands is reported. Five new MOFs have been synthesized by systematic variation of the phosphine ligands and metal precursors employed, and these represent the first examples of MOFs constructed using phosphine–metal bonds as the sole structural component. Furthermore, the MOFs display solid-state luminescence, with emission maxima that are significantly red-shifted compared to Pd(PPh 3 ) 4 . In addition, a Rh I low-valent coordination solid based on the same linker design is reported, which displays solid-state luminescence that is not observed for the molecular analogue.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1986

Ultrasonic characterization of microstructure in powder metal alloy

The ultrasonic wave propagation characteristics were measured for IN-100, a powder metallurgy alloy used for aircraft engine components. This material was as a model system for testing the feasibility of characterizing the microstructure of a variety of inhomogeneous media including powder metals, ceramics, castings and components. The data were obtained for a frequency range from about 2 to 20 MHz and were statistically averaged over numerous volume elements of the samples. Micrographical examination provided size and number distributions for grain and pore structure. The results showed that the predominant source for the ultrasonic attenuation and backscatter was a dense (approx. 100/cubic mm) distribution of small micropores (approx. 10 micron radius). Two samples with different micropore densities were studied in detail to test the feasibility of calculating from observed microstructural parameters the frequency dependence of the microstructural backscatter in the regime for which the wavelength is much larger than the size of the individual scattering centers. Excellent agreement was found between predicted and observed values so as to demonstrate the feasibility of solving the forward problem. The results suggest a way towards the nondestructive detection and characterization of anomalous distributions of micropores when conventional ultrasonic imaging is difficult. The findings are potentially significant toward the application of the early detection of porosity during the materials fabrication process and after manufacturing of potential sites for stress induced void coalescence leading to crack initiation and subsequent failure.

Tittmann, B. R.↗

DOE OSTI2024

UNCERTAINTIES FOR IN-REACTOR TESTING OF TRITIUM LOADED GETTERS WITH TEMPERATURE CONTROL

The fourth experiment in TPBAR Materials Irradiation Separate-Effects Test (TMIST) series (TMIST-4) is planned to experimentally determine the effect of neutron irradiation on the equilibrium vapor pressure of tritium over a tritium loaded Nickel-Plated Zirconium (NPZ) getter in a simulated TPBAR service environment. This pressure will be used to estimate the tritium permeation rate. In the thermal design in the TMIST-4, two evaluations are required. 1) The cladding temperature is calculated to estimate the feasibility of detecting potential irradiation enhancement of the partial pressure for an NPZ getter. This work is required to obtain a precise cladding temperature for measurement of a low tritium partial pressure. This work has been completed and indicated that the required/target cladding temperatures based on the TMIST-4 test plan can be satisfied under the test condition range by modifying the capsule component shapes and inserting a thermally conductive metal sleeve. 2) The evaluation of uncertainties associated with the test design and operation is performed. This includes fabrication tolerances, and power and nuclear operating conditions. These factors will impact the component temperatures inside capsules and resulting the tritium partial pressure. The tritium permeation rate is a function of temperature and tritium partial pressure. The prediction of tritium permeation rates affects the feasibility of obtaining measurement resolutions required to reach reasonable conclusion for potential irradiation enhanced performance. This work will investigate the uncertainties.

TTP, TPBAR, TMIST-4, TPBAR Materials Irradiation S↗

DOE OSTI2021

Identification of LiH and nanocrystalline LiF in the solid–electrolyte interphase of lithium metal anodes

A comprehensive understanding of the solid–electrolyte interphase (SEI) composition is crucial to developing high-energy batteries based on lithium metal anodes. A particularly contentious issue concerns the presence of LiH in the SEI. In this work, we report on the use of synchrotron-based X-ray diffraction and pair distribution function analysis to identify and differentiate two elusive components, LiH and LiF, in the SEI of lithium metal anodes. LiH is identified as a component of the SEI in high abundance, and the possibility of its misidentification as LiF in the literature is discussed. LiF in the SEI is found to have different structural features from LiF in the bulk phase, including a larger lattice parameter and a smaller grain size (<3 nm). These characteristics favour Li + transport and explain why an ionic insulator, like LiF, has been found to be a favoured component for the SEI. Finally, pair distribution function analysis reveals key amorphous components in the SEI.

36 MATERIALS SCIENCE↗

NASA NTRS1981

Passive components for high temperature operation

The development of resistors, capacitors, and interconnect metalizations utilizing a low pressure chemical vapor deposition (LPCVD) process is described. The LPCVD process allows the passive components to be fabricated at temperatures higher than their highest operating temperatures. The deposition of thin films by LPCVD is accomplished by reacting one or more gases on the surface of a heated substrate. The substrates to be coated are placed on a graphite susceptor and then loaded into the center of a quartz reaction tube. The RF power is applied to the coil on the outside of the reaction tube which in turn is coupled into the graphite susceptor causing it to heat. Pressures of several torr or less are typical, with carrier flow rates of 0.1 to 2.0 liters/min. Nitrogen, hydrogen, and helium are typical carrier gases. These are controlled with mass flow controllers and the pressure is continuously monitored with a capacitive manometer. Materials selection and device testing are also discussed.

Raymond, L. S.↗

NASA NTRSDate not supplied

Principles of Directed Energy Deposition for Aerospace Applications

Metal Additive Manufacturing is changing how components are fabricated for rocket propulsion and aerospace applications. Many additive manufacturing technologies are evolving, and active research is being conducted across academia, industry, and government to advance processes, materials, design, post-processing and applications. While much focus has been on Laser Powder Bed Fusion (LPBF) techniques, several large-scale techniques are also rapidly evolving using directed energy deposition (DED).

Additive Manufacturing↗

NASA NTRS1964

Measurements of thermal-contact conductance between dissimilar metals in a vacuum.

Measuring thermal contact conductance of various dissimilar metal joints in vacuum for testing Saturn electronic components

ELECTRONIC EQUIPMENT TESTING↗

DOE OSTI2022

ExaAM: Metal additive manufacturing simulation at the fidelity of the microstructure

Additive manufacturing (AM), or 3D printing, of metals is transforming the fabrication of components, in part by dramatically expanding the design space, allowing optimization of shape and topology. However, although the physical processes involved in AM are similar to those of welding, a field with decades of experimental, modeling, simulation, and characterization experience, qualification of AM parts remains a challenge. The availability of exascale computational systems, particularly when combined with data-driven approaches such as machine learning, enables topology and shape optimization as well as accelerated qualification by providing process-aware, locally accurate microstructure and mechanical property models. We describe the physics components comprising the Exascale Additive Manufacturing simulation environment and report progress using highly resolved melt pool simulations to inform part-scale finite element thermomechanics simulations, drive microstructure evolution, and determine constitutive mechanical property relationships based on those microstructures using polycrystal plasticity. We report on implementation of these components for exascale computing architectures, as well as the multi-stage simulation workflow that provides a unique high-fidelity model of process–structure–property relationships for AM parts. In addition, we discuss verification and validation through collaboration with efforts such as AM-Bench, a set of benchmark test problems under development by a team led by the National Institute of Standards and Technology.

3D printing↗