SEARCH · Engineering Papers

Results for “electron density profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

All sources NASA NTRS DOE OSTI

NASA NTRS1978

The diurnal and solar cycle variation of the charge exchange induced hydrogen escape flux

On the basis of ion temperature and density data at specific points and times in June 1969 provided by the OGO 6 satellite, and altitude profiles of the ion and electron temperature and concentration provided by the Arecibo radar facility over the period February 1972-April 1974, the diurnal and solar cycle variation of the charge-exchange-induced hydrogen escape flux was investigated. It was calculated that for low to moderate solar activity at Arecibo, the diurnal ratio of the maximum-to-minimum charge-exchange-induced hydrogen escape flux was approximately 6 with a peak around noon and a minimum somewhere between 0100 and 0300 h LT. This study of a limited amount of OGO 6 and Arecibo data seems to indicate that the charge-exchange-induced hydrogen escape flux increases as the F(10.7) flux increases for low to moderate solar activity.

Maher, L. J.↗

NASA NTRS1994

The N (II) 205 micron line in M82: The warm ionized medium

Detection of the 205 micrometer fine structure line of N II in the nearby starburst galaxy M82 is reported. The intensity wihin a 54 sec Full width at Half Maximum (FWHM) beam is (7.1 +/- 1.2) x 10(exp -19) W cm(exp -2). The ratio of the intensity of the recently detected 122 micrometer line to that of the 2.5 micrometer lines is = (4.2) (sup =1.6) (sub -1.2), significantly larger than the corresponding Galactic value of 1.6 +/- 0.3, reflecting higher electron densities within the central 850 pc of M82 in comparison to the Cosmic Background Explorer (COBE) Galactic average. The 2.5 micrometer line profile is consistent with other far-infrared fine-structure line profiles observed in M82. The observations are interpreted in the context of a two-component model of the ionized medium in M82. We find that a component of density as low as approximately 50 cm(exp -3) can comprise up to 70% of the total mass of warm ionized gas within the beam. The balance of the ionized mass is comprised of a component of density approximately greater than 100 cm(exp -3). A model is explored in which the dneser ionized medium constitute the boundaries of neutral surfaces which border the expanding hot plasma from the nuclear region.

Petuchowski, S. J.↗

NASA NTRS1998

Ultrafast Modulation and Switching of Quantum-Well Lasers using Terahertz Fields

Modulation and switching of semiconductor lasers are important for laser-based information technology. Typically the speed of modulation and switching is limited by interband processes such as stimulated and spontaneous recombinations which occur on a nanosecond time scale. This is why the diode laser modulation has been restricted to tens of GHz. Modulation at higher speed is highly desirable as the information technology enters into the so-called tera-era. In this paper, we study the possibility of utilizing THz-field-induced plasma heating to modulate quantum-well lasers. This is a timely study since, with the advancement of THz solid-state sources and free-electron lasers, THz physics and related technology is currently coming out of its infancy. The investigation of interplaying THz and optical fields is also of intruiging fundamental interest. First, we introduce theoretical plasma heating results for the quantum-well optical amplifier in the presense of an intense half-cycle THz pulse. The heated carrier distributions are then utilized to calculate the THz-pulse-induced change in refractive index and gain profile. Since the electron-hole-plasma is heated using intraband transitions, we circumvent the usual complications due to an overall change in density, and the nonlinear recovery is governed solely by the carrier-LO-phonon interactions, typically 5 ps for a complete recovery. This procedure implies THz and sub-THz switching and recovery rates, respectively; using either gain modulation or index modulation. Plasma heating via steady-state THz fields is also studied. Finally, numerical simulation of a coupled set of equations to investigate the THz modulation based on a simplified model for quantum-well lasers is presented. Our results show that a semiconductor laser can be modulated at up to 1 THz with little distortion with a THz field amplitude at the order of a few kV/cm. Laser responses to a change in THz frequency will be shown. Constraints, practicalities, and applications will be discussed.

Ning, Cun-Zheng↗

DOE OSTI2021

Diii-D Research Advancing The Physics Basis For Optimizing The Tokamak Approach To Fusion Energy

DIII-D physics research addresses critical challenges for operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-Ip steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs. ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. With this physics understanding and suite of actuators, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q=10 in ITER at 9 MA was coupled to a detached divertor, and a near Super H-mode optimized-pedestal scenario with co-Ip beam injection, was coupled to a radiative divertor. The Hybrid core scenario was achieved directly, without the need for internal flux pumping, using off-axis current drive actuators, and a controller to avoid mode locking and disruptions in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.

Fenstermacher, M.↗

DOE OSTI2021

Correlation Between Corrugation-Induced Flexoelectric Polarization and Conductivity of Low-Dimensional Transition Metal Dichalcogenides

The tunability of polar and semiconducting properties of low-dimensional transition metal dichalcogenides (TMDs) have propelled them to the forefront of fundamental and applied physical research. These materials can vary their electrophysical properties from nonpolar to ferroelectric, and from direct-band semiconducting to metallic. In addition to classical controlling factors, such as field effect, composition, and doping, new degrees of freedom emerge in TMDs due to the curvature-induced electron redistribution and the associated changes in electronic properties. Here we theoretically explore the elastic and electric fields, flexoelectric polarization and free charge density for a TMD nanoflake placed on a rough substrate with a sinusoidal corrugation profile. Finite element modelling results for different flake thickness and corrugation depth yield insights into the flexoelectric nature of the out-of-plane electric polarization and establish the unambiguous correlation between the polarization and static conductivity modulation. The modulation is caused by the coupling between the deformation potential and inhomogeneous elastic strains, which evolve in the TMD nanoflake due to the adhesion between the flake surface and corrugated substrate. We reveal a pronounced maximum in the thickness dependences of the electron and hole conductivity of MoS 2 and MoTe 2 nanoflakes placed on a corrugated substrate, which opens the way for the optimization of their geometry towards significant improvement in their polar and electronic properties, necessary for advanced applications in nanoelectronics and memory devices. Specifically, the obtained results can be useful for the development of nanoscale straintronic devices based on the bended MoS 2 , MoTe 2 , and MoSTe nanoflakes, such as diodes and bipolar transistors with a bending-controllable sharpness of p-n junctions.

42 ENGINEERING↗

NASA NTRS1995

Observations and physical interpretations of the solar wind flow properties as obtained from white light coronagraph aboard SPARTAN 201-01

The solar corona was observed with an externally occulted White Light Coronagraph (WLC) carried on the SPARTAN 201-1 spacecraft on 11-12 Apr. 1993. With observations from WLC and the ground based Mauna Loa White Light Coronagraph, a large number of polar plumes both in the north and south polar holes were traced from 1.16 to 5.5 Rs. Flow properties of the solar wind in coronal holes have been determined (Habbal et al., 1995) by using a two fluid model constrained by density profiles and scale height temperatures from the white light observations, and interplanetary measurements of the flow speed and proton mass flux from Ulysses' south polar passage. Provisions for acceleration by Alfven waves, as well as electron and proton heating, are included in the momentum and the energy equations respectively. The model computations fit remarkably well the empirical constraints of the two different density structures (plumes and coronal holes) for a range of input parameters. In this study we investigate the physical nature of the heating function used in the two-fluid model. Alfven waves have been suggested as the possible source of heating that accelerates the solar wind (Ofman and Davila, 1995). We utilize the density contrast observed in WLC data in the plume and ambient coronal hole region to estimate the Alfven wave frequencies responsible for heating these structures. The source heating function utilized in the two fluid model of the solar wind acceleration will be compared with the resonant Alfven wave heating function.

Guhathakurta, Madhulika↗

NASA NTRS1984

The flow of plasma in the solar terrestrial environment

The development of electric fields in an expanding plasma was studied. With regard to the polar wind, it was found that hot magnetospheric electrons have a pronounced effect on the polar wind. In addition, there is no O(+) charge exchange barrier and substantial fluxes of O(+) ions can escape with the polar wind. In the auroral plasma physics area, the excitation of electrostatic waves by field aligned auroral electron beams was examined. It was demonstrated that the auroral field aligned current density can be large enough to excite Buneman double layers. For situations that lead to strong double layers, it was shown that the temporal evolution of the potential profile is controlled by current fluctuations. Two dimensional particle in cell simulations were conducted, and the high frequency wave turbulence excited by an auroral electron beam of finite width perpendicular to an ambient magnetic field was investigated. The formation of V shaped auroral potential structures was studied, and numerical simulations of double layers and auroral electric fields were reviewed.

Schunk, R. W.↗

DOE OSTI2024

Effects of delta ray electrons on measurement uncertainties of harp system

A harp system, which is a multi-wire beam profile monitoring (MWPM) system, is planned upstream of the spallation target to make in situ calibration of beam current density configuration on the target along with beam imaging from luminescent coating on the beam entrance window at the Second Target Station (STS) of the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory (ORNL). This beam interception-based beam diagnostics system on the target will be used to ensure that the maximum beam loads on the target are within the design range during neutron production. Current design of the harp consists of three layers of measurement wires each of which is sandwiched between voltage biasing wire planes. The signal obtained from each measurement wire layer is disturbed by secondary electrons (SE) and delta rays produced by beam-matter interactions in neighboring wires and ionization of residual gases in accelerator vacuum. While the backgrounds from SE can be suppressed by voltage biasing, the delta-ray electrons with kinetic energies above keV ranges overcome the electric potential bias. In this paper, we study the effects of delta-rays on the measurement uncertainties of MWPM using the particle transport simulation code FLUKA. Furthermore, the cases where the harp system is installed in the proximity of a large delta ray sources such as proton beam window or in the core vessel filled with sub-atmospheric gas have been studied.

Lee, Yong Joong↗

NASA NTRS1974

Oxygen and hydrogen atom concentration profiles in the premixed propane/oxygen flame

The oxygen and hydrogen free radical (atom) concentration profiles in the premixed propane/oxygen flame at 92.5% oxygen were determined using electron spin resonance (ESR) spectroscopy techniques. The ESR instrument was specially modified so that the flame can be probed for determining the oxygen and hydrogen atom population densities during the actual combustion process of propane burning in oxygen. The technique used for propane is similar to that suggested by Fristrom and Westenberg to measure the free radical concentration profiles in C-C hydrocarbon/oxygen combustion.

Downs, W. R.↗

DOE OSTI2023

Spectroscopic measurement of increases in hydrogen molecular rotational temperature with plasma-facing surface temperature and due to collisional-radiative processes in tokamaks

Abstract Spatially resolved rotational temperature of ground state hydrogen molecules desorbed from plasma-facing surface was measured in QUEST, LTX-β, and DIII-D tokamaks, and the increases of the rotational temperature with the surface temperature and due to collisional-radiative processes in the plasmas were evaluated. The increase due to collisional-radiative processes was calculated by solving rate equations considering electron and proton collisional excitation and deexcitation and spontaneous emission. The calculation results suggest a high sensitivity for the rotational temperature to electron and proton densities, but a negligible sensitivity to the electron, proton, and surface temperatures. In the three tokamaks with different plasma parameters and plasma-facing surface materials, the spatial profile of the rotational temperature was estimated using Fulcher-α emission lines (600–608 nm). In QUEST, the spatial profile of the rotational temperature was estimated from spatially resolved spectra. In the other tokamaks, the rotational temperature was evaluated assuming a single point emission with a location determined from the Fulcher-α emission profile as measured with a filtered camera. In metal-walled devices QUEST and LTX-β, the rotational temperature increased with the surface temperature, and the calculated collisional-radiative increase is consistent with measured increase assuming that the rotational temperature at the surface is approximately 500–600 K higher than the surface temperature. In DIII-D with carbon walls, a larger collisional-radiative increase than the other tokamaks was observed because of the higher density leading to a large difference from the calculated increase compared to the other smaller tokamaks. Measurement of the Fulcher-α emission profile with higher spatial resolution in DIII-D may reduce the difference and reveal the effect of the surface temperature on the rotational temperature. These results show the increases in the rotational temperature with the surface temperature and due to the collisional-radiative processes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Nitrogen-seeded divertor detachment in TCV L-mode plasmas

Most of the detachment experiments done to date on the tokamak à configuration variable (TCV), both in standard and alternative divertor geometries, focused on L-mode integrated core density ramps. In view of extending these studies to high-power, high-confinement regimes, where impurity seeding will be necessary for detachment, the properties of nitrogen seeded L-mode detachment in TCV are assessed here with the extensive set of edge and divertor diagnostics and similarities and differences with integrated core density ($\langle n_e \rangle$) ramp detachment experiments are elucidated. It is found that in high current, reversed field plasmas, detachment at the outer target is achieved with N 2 -seeding and density ramps, with target heat flux reductions of up to 90%, while the inner target only detaches with seeding. The Scrape-Off Layer radiation fraction reaches values of 60%–80% and in all situations, a stable radiator can form around the X-point. In this work, the most striking difference between seeding and density ramp is the behavior of the upstream quantities. During the $\langle n_e \rangle$-ramp, a broadening of the upstream density profile (density ‘shoulder’) occurs, concurrent with the outer target ion flux roll-over, while no such behavior occurs during nitrogen seeded detachment. Separatrix density, electron temperature and pressure also evolve strongly with increasing density, and are largely unaffected by the injection of nitrogen. Comparison of upstream and target pressures reveals that, in all cases, the outer target ion flux reduction coincides with the development of a parallel gradient of the total pressure. Common to all cases is also a reduction of energy confinement time with detachment, although this effect is weak for seeding at relatively high density. Studying the impact of the ∇B-drift direction in both nitrogen seeding and core density ramps reveals that drifts mainly affect the behavior at the inner strike point, highlighting the need to include them in edge transport simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Dark matter decay signals in cosmic filaments

Cosmic filaments form the backbone of the cosmic web, yet their properties and evolution remain uncertain. Using the EAGLE hydrodynamical simulations, we investigate the dark matter density profiles in filaments and their implications for dark matter decay signals. We show that GeV-scale dark matter particles decaying into electron-positron pairs can produce detectable radio synchrotron emission. By leveraging stacked filament radio data, we place stringent constraints on the dark matter decay lifetime, improving existing limits by up to two orders of magnitude for strong filamentary magnetic fields.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1977

Morphology and physical parameters of a solar flare

The chromospheric and coronal morphology of the flare of June 15, 1973, (1B/M3) in NOAA active region 131 (McMath 12379) is discussed, and results of quantitative analysis of Skylab soft X-ray observations of the event are presented. H-alpha and white-light observations reveal evidence of emerging flux near the site of the H-alpha flare onset. Preflare and early flare filament activity and its spatial and temporal correlation with the flare are discussed. Spatially resolved soft X-rays are compared with H-alpha and magnetic-field measurements. Full-disk high-temporal-resolution soft X-ray flux measurements and time profiles of the resultant temperature and density calculations are also presented which yield a peak temperature of about 14.2 million K and a peak electron density of approximately 3.5 deg 10 to the -10th power per cu cm and show a preflash-phase temperature rise to about 9 million K. The peak values should be compared with the respective values of approximately 25 million K and 4.5 by 10 to the -10th power per cu cm deduced from the spatially resolved data.

Smith, J. B., Jr.↗

NASA NTRS1993

A new investigation of microbursts at meter-decameter wavelengths

The results of a new investigation of microbursts at meter-decameter wavelengths are reported. Several properties of microbursts reported earlier are confirmed, and some new properties, such as time profile characteristics, flux density, and energy spectra are studied in order to compare the properties of microbursts with those of normal type III bursts. Electron beams of similar characteristics are found to generate both microbursts and type III bursts. Plasma waves generated by the electron beams due to beam-plasma instability are quickly isotropized as they scatter on the density fluctuations in the corona, leading to the low brightness temperature of microbursts. The resulting low levels of plasma waves produce transverse radiation of low brightness temperature. As a result of the isotropization, the second harmonic plasma emission dominates the fundamental, so that microbursts are expected to be primarily a harmonic plasma emission.

Subramanian, K. R.↗

NASA NTRS2010

MIRO Computational Model

A computational model calculates the excitation of water rotational levels and emission-line spectra in a cometary coma with applications for the Micro-wave Instrument for Rosetta Orbiter (MIRO). MIRO is a millimeter-submillimeter spectrometer that will be used to study the nature of cometary nuclei, the physical processes of outgassing, and the formation of the head region of a comet (coma). The computational model is a means to interpret the data measured by MIRO. The model is based on the accelerated Monte Carlo method, which performs a random angular, spatial, and frequency sampling of the radiation field to calculate the local average intensity of the field. With the model, the water rotational level populations in the cometary coma and the line profiles for the emission from the water molecules as a function of cometary parameters (such as outgassing rate, gas temperature, and gas and electron density) and observation parameters (such as distance to the comet and beam width) are calculated.

Broderick, Daniel↗

DOE OSTI2020

Quantifying dislocation density in Al-Cu coatings produced by cold spray deposition

This work quantifies the plastic deformation in terms of dislocation density for a series of cold sprayed Al-Cu coatings with copper contents from 2 mass% to 5 mass%. The success of the deposition and consolidation of the feedstock powders during the cold spray process rely on the occurrence of significant plastic deformation. Inert gas atomized Al-Cu alloy powders were sprayed onto substrates made of an Al-Cu-Mg-Mn alloy (AA2024) to produce dense coatings using a low pressure cold spray system with helium as the carrier gas. X-ray diffraction patterns were obtained from the Al-Cu feedstock powder material and the cold sprayed coatings using a monochromatic X-ray source, and the dislocation density was determined via an X-ray whole profile analysis. Increasing the Cu alloy content (from 2 mass% to 5 mass%) systematically increased the dislocation density in the Al-Cu coatings from (4.3 ± 0.5) × 10 14 m -2 to (7.5 ± 0.8) × 10 14 m -2 . The dislocation densities in the feedstock powders ranging from (0.4 ± 0.1) × 10 14 m -2 to (1.8 ± 0.2) × 10 14 m -2 were all lower than the dislocation densities in the corresponding coatings. The increasing deformation level in the Al-Cu coatings with Cu additions were confirmed by the classic and modified Williamson-Hall analyses of X-ray diffraction data, and peak breadth measurements from neutron diffraction data. Finally, a high density of dislocations was also observed in these coatings via electron backscatter diffraction and transmission electron microscopy.

36 MATERIALS SCIENCE↗

DOE OSTI2023

The physics basis to integrate an MHD stable, high-power hybrid scenario to a cool divertor for steady-state reactor operation

Abstract Coupling a high-performance core to a low heat flux divertor is a crucial step for ITER and a Fusion Pilot Plant or DEMO. Experiments in DIII-D recently expanded the steady-state hybrid scenario to high density and divertor impurity injection to study the feasibility of a radiating mantle solution. This work presents the physics basis for trade-offs between density, current drive and stability to tearing modes (TMs) at high β. EC power is crucial to tailor the plasma profiles into a passively stable state, and to eject impurities from the core. Off-axis EC depositions decrease the heating efficiency, but calculated electron heat transport coefficients show that this effect is partially mitigated by improved confinement inside the EC deposition. Additionally, the reduction in pressure is recovered by increasing the density. This favourable scaling of confinement with density was observed in high power plasmas for years, and this work provides a comprehensive explanation. ELITE predictions indicate that a path in peeling-ballooning stability opens up for certain conditions of density, power, q 95 and shaping, allowing the edge pressure to continue increasing without encountering a limit. In the core, calculated anomalous fast-ion diffusion coefficients are consistent with density fluctuation measurements in the toroidicity-induced Alfvén eigenmode range, showing that smaller fast-ion losses contribute to the enhanced confinement at high density. The edge integration study shows that divertor heat loads can be reduced with Ne and Ar injection, but this eventually triggers a cascade of n = 1, 2, 3 core TMs. We can now show that impurity radiation in the core is small and it is not the cause for the drop in confinement at high Ar and Ne injection rates. The overlap between the core TMs is consistent with the loss of pressure as estimated by the Belt model for the coupled rational surfaces. Optimization of these trade-offs has achieved plasmas with sustained H 98y2 = 1.7, f GW = 0.7 and ∼85% mantle radiation. The scenario and its variations at higher density and on- vs off-axis EC heating has been studied as a candidate for an integrated solution for several reactor designs, such as ITER, ARC, and the ARIES-ACT1 case, showing promising results in terms of fusion power and gain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1972

Anode heat transfer for a flowing argon plasma at elevated electron temperature.

Theoretical investigation of heat transfer from a preionized gaseous plasma flowing over an anode surface at an elevated electron temperature in the presence of an electric field normal to the surface. A laminar boundary layer is considered in which only the velocity profile is locally similar and fluid properties are assumed to change uniformly in the gas flow direction. Results obtained by an approximation method show that for moderate current densities, the velocity and temperature distributions are insensitive to current. In addition, the effect of elevated electron temperature is negligible on convective heat transfer, but is significant for the overall heat transfer due to the enthalpy transport by current. Total heat flux to the anode is obtained by evaluating the Nusselt number and adding terms due to the potential drop in the sheath and the surface work function.

Bose, T. K.↗