Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cost effectiveness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Analysis of Cost-Effective Off-Board Hydrogen Storage and Refueling Stations

This report highlights design and component selection considerations for compressed gas hydrogen fueling stations operating at 5000 psig or 350 bar. The primary focus is on options for compression and storage – in terms of practical equipment options as well as various system configurations and how they influence delivery performance and station economics.

08 HYDROGEN↗

CHARM COST-EFFECTIVE HIGH-EFFICIENCY ADVANCED REFORMING MODULE FINAL TECHNICAL REPORT

Background Creation of a hydrogen infrastructure is an important prerequisite of widespread fuel cell commercialization, especially for the automotive market. Hydrogen is an attractive fuel since it offers an opportunity to replace petroleum-based fuels, but hydrogen occurs naturally only in chemical compounds like water or hydrocarbons that must be chemically converted to produce it. While an ultimate goal is to produce hydrogen through renewable energy sources, steam methane reforming (SMR) of natural gas is currently the most economical solution to initiate the transition to a hydrogen economy. Centralized hydrogen generation using large industrial SMR plants is already in place to serve customers. Yet, because of the weight and size of cylinders needed to contain hydrogen gas or liquid, transportation of hydrogen may only be economical for short distances. Consequently, distributed natural gas reforming, which trades off the economies of scale of large plants for simplified delivery logistics, is an attractive alternative that could address immediate problems with the lack of hydrogen infrastructure.

08 HYDROGEN↗

Commercial and Cost Effective Production of Gas Electron Multiplier (GEM) Foils

The nuclear and high energy physics research community is constantly searching for new and improved tracking and radiation detectors. The introduction of micropattern detectors has opened new opportunities for improving the rate capabilities, as well as the spatial and time resolution of particle detectors in these applications. GEM detectors in particular have received enormous interest for use in detectors planned for a number of new and upgraded experiments at many different research facilities. These include both the STAR and PHENIX experiments at the Relativistic Heavy Ion Collider at Brookhaven National Laboratory, experiments at the Thomas Jefferson National Laboratory, Oak Ridge National Laboratory, and at the future electron-positron Linear Collider. At the present time, CERN is not able to supply foils in sufficient quantities to accommodate the needs of these experiments. Compounding this problem, there is a strong interest in GEM foils for numerous other applications, such as in astrophysics, medical imaging and detectors for homeland security. It would therefore be of significant benefit to the research community to develop a commercial source of GEM foils for all of these applications. Tech-Etch is in a unique position to develop this technology for commercial use. Tech-Etch has not only experience in numerous related high precision etched Kapton® products, but it also has strong ties with several research institutions (namely Brookhaven, Yale and MIT) that can help develop and evaluate the performance of the GEM foils produced at Tech-Etch. Additionally, since Tech-Etch is a small company, it also has the capability to produce a large variety of part configurations, as well as the flexibility to shift production methods, equipment, and chemistry to optimize the GEM foil manufacturing process without being constrained by existing work running on high volume continuous coil equipment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A Molten Salt Electrochemical Process for the Preparation of Cost-Effective p-Block (Coating) Materials

Solar energy applications rely heavily on p-block elements and transition metals. Silicon is, by far, the most commonly used material in photovoltaic cells and accounts for about 85% of modules sold presently. Of late, thin film photovoltaic cells have gained momentum because of their higher efficiencies. Most of these thin film devices are made out of just five elements, namely, cadmium, tellurium, selenium, indium, gallium and copper. The present manuscript describes an elegant and inexpensive molten salt-based electrolytic process for fabricating a tellurium-coated metallic substrate. A three-electrode set up was employed to coat iridium with tellurium from a molten bath containing lithium chloride, lithium oxide and tellurium tetrachloride (LiCl-Li 2 O-TeCl 4 ) at 650 °C for a duration ranging from 30 to 120 min under a galvanostatic mode. The tellurium coating was observed to be thick, uniform, smooth and homogeneous. Additionally, the deposited tellurium did not chemically react with the iridium substrate to form intermetallic compounds, which is a good feature from the standpoint of the device’s performance characteristics. The present process, being generic in nature, shows the potential for the manufacture of both the coated substates and high-purity elements not just for tellurium but also for other p-block elements.

36 MATERIALS SCIENCE↗

Air transportation - Energy cost-effective or not

Current technology aircraft have energy intensities comparable to ground transport modes. Operational changes can further improve their relative energy performance. Wide-body aircraft have already significantly improved fleet energy intensity and will continue to do so as they become more predominant. This is reflected in the 1972 fleet-wide energy intensity data which show both the domestic and international carriers at the lowest jet aircraft intensity levels ever attained. Technological improvements decreased the energy requirements of wide-body aircraft while also significantly reducing aircraft noise and pollution emission levels. Load factor is the most significant parameter affecting existing aircraft energy intensity and therefore should be raised. Fuel scarcity is now forcing such a change.

Maddalon, D. V.↗

Cost-effective actuator tester

Group of preprogrammed plug-in cards and control module converts breadboard control electronics of actuator assembly to actuator tester. System utilizes electronic control, and hydraulic systems of breadboard actuator into which it is installed.

Kopp, G. F.↗

Cost-effective use of minicomputers to solve structural problems

Minicomputers are receiving increased use throughout the aerospace industry. Until recently, their use focused primarily on process control and numerically controlled tooling applications, while their exposure to and the opportunity for structural calculations has been limited. With the increased availability of this computer hardware, the question arises as to the feasibility and practicality of carrying out comprehensive structural analysis on a minicomputer. This paper presents results on the potential for using minicomputers for structural analysis by (1) selecting a comprehensive, finite-element structural analysis system in use on large mainframe computers; (2) implementing the system on a minicomputer; and (3) comparing the performance of the minicomputers with that of a large mainframe computer for the solution to a wide range of finite element structural analysis problems.

Storaasli, O. O.↗

Cost effective flat plate photovoltaic modules using light trapping

Work in optical trapping in 'thick films' is described to form a design guide for photovoltaic engineers. A thick optical film can trap light by diffusive reflection and total internal reflection. Light can be propagated reasonably long distances compared with layer thicknesses by this technique. This makes it possible to conduct light from inter-cell and intra-cell areas now not used in photovoltaic modules onto active cell areas.

Bain, C. N.↗

Development of an All-Metal Thick Film Cost Effective Metallization System for Solar Cells

Materials including copper powders, silver-fluoride, and silicon wafers were procured and copper pastes were prepared. Electrodes made with copper pastes were analyzed and compared with the raw materials. A needle-like structure was observed on the electroded solar cells, and was identified as eutectic copper-silicon by electron probe X-ray spectroscopy. The existence of this phase was thought to benefit electrical and metallurgical properties of the contact. Subsequently electrodes made from new material were also shown to contain this phase while simultaneously having poor adhesion.

Ross, B.↗