SEARCH · Engineering Papers

Results for “consumption potential”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Performance Evaluation of Three RTU Energy Efficiency Technologies

This project was part of an effort by CLEAResult and ComEd to evaluate the energy saving potential of emerging technologies in the Chicago area. This project focused on evaluating emerging technologies related to rooftop units (RTUs). An RTU with a single-stage compressor and a constant-speed fan with an induction motor was selected as the baseline for technology comparison. Three retrofit strategies were investigated. The first two involved replacing the single-stage compressor of an RTU by either a two-stage or variable-speed compressor and adding a variable frequency drive (VFD) to the constant speed fan. The use of a multi-/variable-stage compressor improves the part-load efficiency of the compressor which will ultimately result in annual energy savings as well as peak demand shaving in some cases where the design capacity of the RTU is larger than the maximum cooling load of the building space that it is serving. The third technology was the use of a high rotor pole switched reluctance motor (SRM) as a replacement for the constant-speed supply fan. The SRM was applied in single-speed, two-stage and variable-speed compressor RTUs. SRM motors run via reluctance torque. Their stator poles are driven by direct current (DC) power and require an inverter as well as active control when using alternating current (AC) power. This inherent property results in high efficiency over a range of operating conditions. It also exhibits higher efficiency compared to variable frequency drives (VFDs) since its switching frequency is much slower (SCE, 2018).The three technologies investigated are summarized below: 1) Replacing the single-speed compressor with a two-stage compressor and adding a VFD to the supply fan. 2)Replacing the single-speed compressor with a variable-speed compressor and adding a VFD to the supply fan. 3) Replacing the constant-speed induction motor of the supply fan with a high rotor pole SRM. DOE’s building simulation platform EnergyPlus and its graphical user interface OpenStudio were used to evaluate the energy-saving potential of upgrading RTUs, by leveraging experimental data from previous research.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2024

Assessing the Impacts of CO 2 Reduction and Utilization Technologies on Regional Freshwater Resources

This work, a product of the Bioenergy Technologies Office (BETO)-supported multi-lab CO 2 Reduction and Upgrading for e-Fuels Consortium (CO 2 RUe), focuses on advanced research and development and cross-cutting evaluation of environmental, economic, and social sustainability for CO 2 reduction and upgrading for fuels and chemicals. The Consortium develops and de-risks advanced technologies that use renewable electricity to convert CO 2 into e-fuels and commodity chemicals. One key aspect of environmental sustainability consideration is water resources. This report summarizes a three-year study that analyzed the impacts of water consumption in select CO 2 reduction and utilization technologies in two future scenarios using a pair of water indices—water availability index and water stress footprint. The analyses also account for projected electricity grid mixes and their water withdrawal and water consumption demand in grid regions. The work identifies drivers, challenges, and critical areas in water sustainability, along with valuable insights into technological and regional factors. The study also explores the potential of using non-traditional water resources to reduce water stress and increase availability. These findings are intended to support industry stakeholders and BETO with the knowledge needed for informed decision-making, contributing to strategies to mitigate risks associated with the implementation of CO 2 utilization technologies.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2024

Assessing the Impacts of CO 2 Reduction and Utilization Technologies on Regional Freshwater Resources

09 BIOMASS FUELS↗

NASA NTRS1982

Application of future remote sensing systems to irrigation

Area estimates of irrigated crops and knowledge of crop type are required for modeling water consumption to assist farmers, rangers, and agricultural consultants in scheduling irrigation for distributed management of crop yields. Information on canopy physiology and soil moisture status on a spatial basis is potentially available from remote sensors, so the questions to be addressed relate to: (1) timing (data frequency, instantaneous and integrated measurement); and scheduling (widely distributed spatial demands); (2) spatial resolution; (3) radiometric and geometric accuracy and geoencoding; and (4) information/data distribution. This latter should be overnight, with no central storage, onsite capture, and low cost.

Miller, L. D.↗

NASA NTRS1957

Extended Operation of Turbojet Engine with Pentaborane

A full-scale turbojet engine was operated with pentaborane fuel continuously for 22 minutes at conditions simulating flight at a Mach number of 0.8 at an altitude of 50,000 feet. This period of operation is approximately three times longer than previously reported operation times. Although the specific fuel consumption was reduced from 1.3 with JP-4 fuel to 0.98 with pentaborane, a 13.2-percent reduction in net thrust was also encountered. A portion of this thrust loss is potentially recoverable with proper design of the engine components. The boron oxide deposition and erosion processes within the engine approached an equilibrium condition after approximately 22 minutes of operation with pentaborane.

Useller, James W↗

DOE OSTI2024

Non-Electricity Based Renewable Fuels: Theory and Computation for Solar Thermochemical Hydrogen

Dominated by photovoltaics and wind, current renewable energy sources generate mostly electricity, but 80% of the global final energy consumption occurs in form of fuels. Therefore, direct solar fuel generation would be a major breakthrough for the energy transition. Solar thermochemical hydrogen (STCH) is one of the very few potential routes towards scalable renewable fuels, but currently suffers from lack of an oxide working material that could optimally perform energy conversion within the thermodynamic boundary conditions. Theory and computation can contribute in two distinct ways, through materials search and discovery, but also by providing detailed mechanistic models for specific systems so to advance our understanding of possible design strategies. To enable high-throughput materials screening, we developed a defect graph neural network (dGNN) machine learning approach,[1] which accelerates the prediction of defect formation energies by replacing the tedious density functional theory (DFT) supercell calculations for all possible defect sites. This approach enables high-throughput database screening of oxides, which was integrated with thermodynamic modeling to extract the reduction entropies as additional selection criterion for STCH. Once potential candidate materials are identified, detailed models can guide materials design by predicting performance characteristics. One challenge is to quantitatively predict thermochemical equilibria at high concentrations when the redox active defects start to interact with each other, thereby impeding the formation of additional defects. Introducing a model for the free energy of defect interaction, parametrized on the basis of DFT data, we simulated the complete STCH redox cycle for (Sr,Ce)MnO3 alloys, achieving near-quantitative agreement with experimental data.[2] The analysis of these simulations reveals how defect interactions diminish the reduction entropy and H2 yield, suggesting to include these interactions in design considerations. Finally, we revisit the popular van't Hoff method for analyzing reduction enthalpies and entropies. This method is not ideal, as it involves a temperature-dependent convolution of gas-phase and solid-state entropies, causing uncertainties in the same order of magnitude as the physical quantities of interest. To avoid this problem, we suggest a simple alternative approach which can be applied to experimental and simulated data alike.

first-principles calculations↗

DOE OSTI2022

Ultra-fast microwave regeneration of CO 2 solid sorbents for energy-efficient direct air capture

Large-scale deployment of direct air capture (DAC) technologies has become critical for mitigating climate change. Towards this end, energy-efficient regeneration of the sorbents used in the process of carbon capture from air is very important to significantly reduce the high operational cost of DAC. Guanidine compounds can be used with environmentally friendly aqueous amino acids (e.g., potassium sarcosinate) for fast and effective CO 2 capture from air, and have a strong potential for low-energy CO 2 release and sorbent regeneration. In this process, the amino acid absorbs the CO 2 from the air, and the guanidine compounds react with the CO 2 -rich amino acid solution and crystallize as an insoluble carbonate salt. Separation and thermal regeneration of the precipitated guanidine carbonate salt leads to an overall low-temperature and low-energy direct air capture process. Effective CO 2 release from the solid guanidine compound can be achieved by mild heating at 120 °C. Here, in this study, to overcome the relatively inefficient traditional conductive heating of the crystalline solid (i.e., Methylglyoxal-bis(iminoguanidine) carbonate, MGBIG carbonate), we evaluated the feasibility of microwave heating of MGBIG carbonate in terms of power requirement, radiation time, and solids mass for efficient CO 2 desorption. The energy consumption needed by a microwave oven and a conventional oven to regenerate the same mass of the sorbent was directly measured to compare the total energy required per unit mass of regenerated sample and provide an understanding of the potential benefits of microwave regeneration. We found that microwave heating effectively regenerates MGBIG carbonate, which may be facilitated by the water molecules that are co-crystallized with carbonate in the guanidine crystals. Microwave heating at 2.54 GHz with 1250 W is up to 17 times faster than conventional conductive heating at 160 °C, resulting in 40 % electrical energy reduction. These results indicate that microwave regeneration may be an energy-efficient method for fast regeneration of solid sorbents used for direct air capture.

42 ENGINEERING↗

DOE OSTI2024

Innovating the next generation of commercial smart building software

Nearly 30% of commercial building energy use is wasted due to equipment faults and HVAC controls problems. The result is increased emissions, compromised comfort and productivity, and less reliable coordination of building power needs with a clean grid. The energy impact alone represents $17 billion in potential savings. Today’s smart building software provides a robust solution to address these operational deficiencies. Energy management and information systems (EMIS) are saving up to 9% on average, with two-year paybacks. They are being incorporated into energy management processes, commissioning services, and utility programs. As effective as they are, two barriers prevent even deeper benefits; limited personnel to fix problems once they are identified, and the expense and time to manually implement changes in control systems. In partnership with the research community, the EMIS industry is developing new capabilities to overcome these barriers. Moving beyond siloed products for either fault detection and diagnostics, or optimal control, these new capabilities empower users to not only automatically identify faults, but also to push corrective action, and control improvements to their buildings. In this paper, several areas for enhancements are documented: ‘one-time’ correction of faults such as setpoints, schedules, and economizer lockouts; short-term active testing for automated proportional integral derivative (PID) loop tuning and functional testing; and continuous supervisory control for demand flexibility and year-round efficiency. Results are presented from a pair of partner implementations out of a dozen providers integrating these enhancements into their products, including field tests from across the country, and insights into operator acceptance and integration into operations and maintenance practices.

Casillas, Armando↗

DOE OSTI2024

Porous Iron Electrodes Reduce Energy Consumption During Electrocoagulation of a Virus Surrogate: Insights into Performance Enhancements Using Three-Dimensional Neutron Computed Tomography

Electrocoagulation has attracted significant attention as an alternative to conventional chemical coagulation because it is capable of removing a wide range of contaminants and has several potential advantages. In contrast to most electrocoagulation research that has been performed with nonporous electrodes, in this study, we demonstrate energy-efficient iron electrocoagulation using porous electrodes. In batch operation, investigation of the external pore structures through optical microscopy suggested that a low porosity electrode with sparse connection between pores may lead to mechanical failure of the pore network during electrolysis, whereas a high porosity electrode is vulnerable to pore clogging. Electrodes with intermediate porosity, instead, only suffered a moderate surface deposition, leading to electrical energy savings of 21% and 36% in terms of electrocoagulant delivery and unit log virus reduction, respectively. Neutron computed tomography revealed the critical role of electrode porosity in utilizing the electrode’s internal surface for electrodissolution and effective delivery of electrocoagulant to the bulk. Energy savings of up to 88% in short-term operation were obtained with porous electrodes in a continuous flow-through system. Further investigation on the impact of current density and porosity in long-term operation is desired as well as the capital cost of porous electrodes.

42 ENGINEERING↗

DOE OSTI2021

Impact of downhole pressure and fluid-access on the effectiveness of wellbore cement expansion additives

Autogenous shrinkage of wellbore cement widely impairs zonal isolation. MgO-based cement expansion additives (CEAs) can mitigate this shrinkage, or even impart net expansion, by creating porosity through displacive crystal growth-processes. However, both MgO hydration and autogenous shrinkage behaviour depend strongly on stress state. Evaluation of CEA performance in wellbore cements therefore requires testing under elevated pressures representative for subsurface environments. We report experiments addressing the chemical and bulk volume changes that occur in cement hydrating at 10 MPa confining pressure and 90 °C. Volumetric response was investigated as function of MgO concentration, external water supply, and pore pressure decrease through water consumption during reaction. Results show the bulk expansion achieved using MgO-based CEAs diminishes markedly with increasing effective confining pressure or, equivalently, upon restricting fluid supply. This reduced expansion-potential under pressure has profound implications for slurry design, notably regarding CEA-concentrations required to counteract micro-annulus formation while maintaining low cement permeability.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Removal and recovery of ammonia from simulated wastewater using Ti3C2Tx MXene in flow electrode capacitive deionization

Abstract Flowing electrode capacitive deionization systems (FE-CDI) have recently garnered attention because of their ability to prevent cross contamination and operate in uninterrupted cycles ad infinitum. Typically, FE-CDI electrodes suffer from low conductivity, reducing deionization performance. Utilization of higher mass loadings to combat this leads to poor rheological properties. Herein, Ti 3 C 2 T x MXene was introduced as 1 mg mL −1 slurry electrodes in an FE-CDI system for the removal and recovery of ammonia from simulated agricultural wastewater. The electrode performance was evaluated by operating the FE-CDI system with a feed solution of 500 mg L −1 NH 4 Cl running in batch mode at a constant voltage of 1.20 and −1.20 V in charging and discharging modes, respectively. Despite the low loading, Ti 3 C 2 T x flowing electrodes showed markedly improved performance, achieving 60% ion removal efficiency in a saturation time of 115 min with an adsorption capacity of 460 mg g −1 . To understand the high adsorption performance of the electrodes, physiochemical and structural analysis was done via a variety of characterization techniques such as SEM, TEM, XRD, DLS, and Raman spectroscopy. Cyclic voltammetry and galvanostatic charge/discharge profiles were obtained to evaluate the electrochemical properties of the electrodes. The system proved to be an energy-saving technology by exhibiting a charge efficiency of 58–70% while operating at an energy consumption of 0.45 kWh kg −1 . A 92% regeneration efficiency showed that the electrodes were stable and suitable for long term and scalable usage. The results demonstrate that MXenes have the potential to improve the FE-CDI process for energy-efficient removal and recovery of ammonia.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Minimum GHG emissions and energy consumption of U.S. PET and polyolefin packaging supply chains in a circular economy

There is a wide agreement on the urgency of transforming linear management of plastics towards a circular economy model. However, no clear pathways exist as to required recycling technologies involved and system-wide environmental impacts. This study explores such pathways in the U.S. for the most commonly used packaging plastics through a combination of mechanical and emerging advanced recycling technologies. A system optimization model aimed at minimizing environmental impacts was developed to determine optimal end-of-life (EOL) management and locations of existing and emerging U.S. recycling infrastructures. Our study includes material flows from virgin resin production through semi-manufacturing processes to existing EOL disposal and recycling processes. An optimized circular plastics packaging system achieved greenhouse gas (GHG) emission savings of up to 28% and cumulative energy demand (CED) savings of up to 46%, compared to the linear economy. Moreover, these savings of GHG emissions and CED impacts represent a reduction of 0.16% and 0.49% compared to annual U.S. GHG emissions and energy consumption in 2022, respectively. The optimal recycling rates and systems-level circularity ranged from 78–99% and 57–75%, respectively. Increased energy savings led to increased GHG emissions showing a potential trade-off between GHG emissions and energy. Analysis of 40 scenarios showed the importance of material collection distances, blend limit of mechanically recycled resins, process yields, and mandated recycling rates for achieving a sustainable circular economy of plastics.

09 - BIOMASS FUELS↗

DOE OSTI2021

Magnetic ordering suppressed phase transformation of a TRIP-HEA during thermal cycling

Transformation-induced plasticity (TRIP) high-entropy alloys (HEAs) have drawn great attention as they present excellent mechanical properties, and their phase stability is critical for the underlying deformation mechanisms and the application temperature range. In this study, the kinetic phase transformation behavior of a dual-phase TRIP-HEA Fe 50 Mn 30 Co 10 Cr 10 (at. %) was probed by in situ neutron diffraction during thermal cycling between 293 and 425 K. Continuous austenitic and martensitic transformation were visualized through the evolution of hexagonal close-packed phase fraction during thermal cycling. Specifically, thanks to the magnetic sensitivity of neutron diffraction, it was found that the martensitic transformation under cooling became suppressed when the antiferromagnetic ordering started at ~326 K. This temperature was further confirmed as the Néel temperature by magnetization measurements. In this work, thermodynamic calculations revealed that the suppression effect on martensitic transformation is attributed to the consumption of the chemical driving force by the magnetic ordering. The magnetic ordering at such relatively high temperature is associated with the high Mn content. These findings shed light on a potential strategy to achieve better mechanical properties of Mn-containing alloys by manipulating the magnetic property through tuning the Mn content.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Cumulative effects of piscivorous colonial waterbirds on juvenile salmonids: A multi predator-prey species evaluation

We investigated the cumulative effects of predation by piscivorous colonial waterbirds on the survival of multiple salmonid ( Oncorhynchus spp.) populations listed under the U.S. Endangered Species Act (ESA) and determined what proportion of all sources of fish mortality (1 –survival) were due to birds in the Columbia River basin, USA. Anadromous juvenile salmonids (smolts) were exposed to predation by Caspian terns ( Hydroprogne caspia ), double-crested cormorants ( Nannopterum auritum ), California gulls ( Larus californicus ), and ring-billed gulls ( L . delawarensis ), birds known to consume both live and dead fish. Avian consumption and survival probabilities (proportion of available fish consumed or alive) were estimated for steelhead trout ( O . mykiss ), yearling Chinook salmon ( O . tshawytscha ), sub-yearling Chinook salmon, and sockeye salmon ( O . nerka ) during out-migration from the lower Snake River to the Pacific Ocean during an 11-year study period (2008–2018). Results indicated that probabilities of avian consumption varied greatly across salmonid populations, bird species, colony location, river reach, and year. Cumulative consumption probabilities (consumption by birds from all colonies combined) were consistently the highest for steelhead, with annual estimates ranging from 0.22 (95% credible interval = 0.20–0.26) to 0.51 (0.43–0.60) of available smolts. The cumulative effects of avian consumption were significantly lower for yearling and sub-yearling Chinook salmon, with consumption probabilities ranging annually from 0.04 (0.02–0.07) to 0.10 (0.07–0.15) and from 0.06 (0.3–0.09) to 0.15 (0.10–0.23), respectively. Avian consumption probabilities for sockeye salmon smolts was generally higher than for Chinook salmon smolts, but lower than for steelhead smolts, ranging annually from 0.08 (0.03–0.22) to 0.25 (0.14–0.44). Although annual consumption probabilities for birds from certain colonies were more than 0.20 of available smolts, probabilities from other colonies were less than 0.01 of available smolts, indicating that not all colonies of birds posed a substantial risk to smolt mortality. Consumption probabilities were lowest for small colonies and for colonies located a considerable distance from the Snake and Columbia rivers. Total mortality attributed to avian consumption was relatively small for Chinook salmon (less than 10%) but was the single greatest source of mortality for steelhead (greater than 50%) in all years evaluated. Results suggest that the potential benefits to salmonid populations of managing birds to reduce smolt mortality would vary widely depending on the salmonid population, the species of bird, and the size and location of the breeding colony.

Evans, Allen F.↗

DOE OSTI2024

A Multidisciplinary Approach to Integrated Energy Systems: Advanced Nuclear Plants with Thermal Storage for Dynamic and Flexible Operation in Diverse Markets

Energy supply, distribution, and demand are continuously evolving in accordance with the integration of new power generation sources. In the United States, there is a progressive shift toward incorporating fluctuating energy sources such as wind and solar into the energy mix, alongside the distributed generation. Simultaneously, we are seeing a revolution in consumer technologies such as electric vehicles, energy devices for both residential and commercial use, and industrial processes—all contributing to a fundamental change in energy consumption dynamics. These scenarios have led to huge demand for enhanced flexibility from nuclear power plants (NPPs), requiring them to operate with unprecedented adaptability. Furthermore, advanced NPPs (A-NPPs) could potentially apply to scenarios in which power generation flexibility is prioritized over its current and conventional baseload generation capacity for traditional demand patterns. The present work covers several configurations for coupling nuclear energy production with thermal energy storage (TES). Previous work evaluated systems entailing a simple nuclear-TES configuration that used steam as a heat source for the TES of three different advanced reactors (ARs), but its heat diversion ratio (HDR) for charging was limited. The present work proposes a new configuration that features full decoupling of the nuclear reactor and the power cycle, using reactor coolant (i.e., gas) as a heat source for the TES and offering a theoretically unlimited HDR. This configuration is, however, more complex, as both high- and low-temperature TES (HT-TES and LT-TES) systems are required in order to cover the extended temperature range. Although this configuration imposes certain limitations on the discharge system configuration, it also presents the opportunity to design a more efficient system. For this case in particular, a steam reheat cycle is advantageous. Conventional TES systems take advantage of nominal efficiency when discharging, whereas the reheat cycle in the fully decoupled TES system affords a significant efficiency increase over conventional cases. Material selection, component/equipment sizing, and costing analyses were performed, followed by economic dispatch and size optimization. Dynamic models were developed for the decoupled system in order to generate insights into aspects of off design operation (e.g., drops in cycle efficiency), and these models enable exploration of potential mitigation strategies for addressing such drops. The models also highlight the need to design fail-safes that ensure continuous operational stability and minimize the impact of power ramping on the reactor parameters.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

NASA NTRS1975

ECASTAR: Energy conservation. An assessment of systems, technologies and requirements

A methodology was presented for a systems approach to energy conservation actions and their potentials and impacts in the United States. Constraints affecting the approach were ranked, and the most important ones are the present economic and technical conditions. The following unresolved issues were identified: consumptive lifestyles vs. conservation ethic, environmental standards vs. energy conservation, capital availability, decentralization and vertical integration vs. centralization, fuel rich regions vs. fuel poor regions, supply vs. end use conservation, life cycle costing vs. initial cost, mandatory savings vs. voluntary savings, labor intensive vs. capital intensive, price control vs. free market. The following recommendations were made: provide action/impact assessment, establish regional energy centers, improve technology articulation with government, design total energy systems, utilize existing systems approach expertise.

Source record↗

NASA NTRS1981

Structures, performance, benefit, cost study

Aircraft engine structures were studied to identify the advanced structural technologies that would provide the most benefits to future aircraft operations. A series of studies identified engine systems with the greatest potential for improvements. Based on these studies, six advanced generic structural concepts were selected and conceptually designed. The benefits of each concept were quantitatively assessed in terms of thrust specific fuel consumption, weight, cost, maintenance cost, fuel burned and direct operating cost plus interest. The probability of success of each concept was also determined. The concepts were ranked and the three most promising were selected for further study which consisted of identifying and comprehensively outlining the advanced technologies required to develop these concepts for aircraft engine application. Analytic, fabrication, and test technology developments are required. The technology programs outlined emphasize the need to provide basic, fundamental understanding of technology to obtain the benefit goals.

Feder, E.↗

NASA NTRS2005

Analytical Micromechanics Modeling Technique Developed for Ceramic Matrix Composites Analysis

Ceramic matrix composites (CMCs) promise many advantages for next-generation aerospace propulsion systems. Specifically, carbon-reinforced silicon carbide (C/SiC) CMCs enable higher operational temperatures and provide potential component weight savings by virtue of their high specific strength. These attributes may provide systemwide benefits. Higher operating temperatures lessen or eliminate the need for cooling, thereby reducing both fuel consumption and the complex hardware and plumbing required for heat management. This, in turn, lowers system weight, size, and complexity, while improving efficiency, reliability, and service life, resulting in overall lower operating costs.

Min, James B.↗