SEARCH · Engineering Papers

Results for “cavity flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Investigations of microwave plasmas - Applications in electrothermal thruster systems

Experimental studies which have been conducted to develop understanding of plasma processes used for spacecraft propulsion are reviewed. The techniques discussed are calorimetry and volume measurements using the TM 011 and TM 012 modes in the microwave cavity system. The use of plasmas in electrical propulsion and microwave induction is reviewed. Plasma containment, microwave power production, energy distribution, and the pressure and flow dependence of the energy distribution are addressed. The plasma dimensions and their dependence on pressure, flow, and power are considered.

Haraburda, Scott S.↗

NASA NTRS1999

Flight Experiment to Study Double-Diffusive Instabilities in Silver-Doped Lead Bromide Crystals

A detailed study on the effect of convection on crystal quality was carried out by growing lead bromide crystals in transparent Bridgman furnace. Direct observations were made on the solid-liquid interface and a new kind of instability was observed. This could be explained on the basis of toroidal flow in the AgBr-doped lead bromide sample. With the increasing translation velocity, the interface changed from flat to depressed, and then formed a cavity in the center of the growth tube. The crystal grown at the lowest thermal Rayleigh number showed the highest quality and crystal grown at the largest thermal Rayleigh number showed the worst quality. Numerical studies were carried out to provide a framework for interpreting the observed convective and morphological instabilities, and to determine the critical (limiting) concentration of dopant for a particular growth velocity and gravity level. Theoretical instability diagrams were compared with data obtained from the experimental studies. These studies provided basic data on convective behavior in doped lead bromide crystals grown by the commercially important Bridgman process.

Singh, N. B.↗

NASA NTRS1988

The diamagnetic effect during AMPTE's tail releases - Initial results

A series of four plasma injection experiments were performed by the AMPTE-IRM spacecraft in the nighttime magnetosphere between 12 and 18 earth radii geocentric distance during spring 1985. The most prominent effect of these tail releases is the creation of magnetic cavities. The lifetime of the cavities ranged from a few seconds to some minutes, depending mainly on the ion species and secondly on the ambient field strength. Due to the subsonic and sub-Alfvenic environment, the interaction between the plasma cloud and the ambient plasma flow played only a minor role in these cases (in contrast to the releases in the solar wind), and thus the diamagnetic effect could be studied extensively. The perturbation of the exterior field and fine structures in the current-carrying shell were observed. The thickness of the shell and the current distribution in this layer were deduced from the magnetic recordings each time IRM entered the cavity.

Luehr, H.↗

NASA NTRS1999

Flow Trajectories in Friction Stir Welding

In the Friction Stir Welding (FSW) process, a rotating, shouldered tool with a threaded pin is inserted under pressure along the seam of two pieces of metal which are tightly clamped together, and secured against a rigid anvil underneath. The rotating pin travels along the seam and through a combination of pressure and friction heating produces a zone of plastic deformation around the pin within the workpiece on either side of the seam. As the pin is moved in the direction of welding, the plasticised material moves around the tool and bonds together behind it. The elements of the material flow behavior are a combination of three elements. There is a rotational transport of material being carried around the tool, extrusion of material being forced around the pin on both sides into the cavity created behind it, and a lifting and dropping of material as it is stirred and mixed by the rotating action of the pin. It was assumed that rotational motion of the plastic zone is the primary mechanism for transport of material around the welding tool. A kinematic mathematical model was used to compute trajectories of material movement for various distributions of rotational slip within the plastic zone. These trajectories were then compared with the results of an experiment that produced radiographs of markers embedded in a workpiece that was welded with the FSW process. It was assumed that the copper wire markers retained their original length as the aluminum material flowed around them. The kinematic model included a constraint so that the displacements were such that the total length of the wire markers did not increase after deformation. There was good agreement between the calculated trajectories for the case of localized slip at the outer surface of the plastic deformation zone and the radiographs of the copper wire markers. The trajectories differed markedly from the radiograph traces when a distributed slip zone was assumed. It was concluded that the flow field could be described generally by a rotating plug model with slip occurring on the surface at the outer boundary of the plastic zone.

Bernstein, Edward L.↗

NASA NTRS1995

Numerical simulation of the SOFIA flow field

This report provides a concise summary of the contribution of computational fluid dynamics (CFD) to the SOFIA (Stratospheric Observatory for Infrared Astronomy) project at NASA Ames and presents results obtained from closed- and open-cavity SOFIA simulations. The aircraft platform is a Boeing 747SP and these are the first SOFIA simulations run with the aircraft empennage included in the geometry database. In the open-cavity runs the telescope is mounted behind the wings. Results suggest that the cavity markedly influences the mean pressure distribution on empennage surfaces and that 110-140 decibel (db) sound pressure levels are typical in the cavity and on the horizontal and vertical stabilizers. A strong source of sound was found to exist on the rim of the open telescope cavity. The presence of this source suggests that additional design work needs to be performed in order to minimize the sound emanating from that location. A fluid dynamic analysis of the engine plumes is also contained in this report. The analysis was part of an effort to quantify the degradation of telescope performance resulting from the proximity of the port engine exhaust plumes to the open telescope bay.

Klotz, Stephen P.↗

NASA NTRS1971

Hollow cathode, quasi-steady MPD arc

A quasi-steady MPD accelerator has been operated with four different hollow cathodes over a power range from 5 kilowatts to 5 megawatts. The absolute level of the argon mass flow, as well as the fractional division of the flow between the cathode and the six standard chamber injectors, is varied over a range of 1 to 12 grams per second. For a fixed total current, it is observed that the voltage increases monotonically with mass flow rate, compared to the usual experience with solid cathodes where the voltage decreases with mass flow rate. For a fixed percentage of flow through the cathode, each hollow cathode configuration displays a minimum impedance at a particular value of the total mass flow. It is asserted that in order to keep the discharge inside the hollow cathode the magnetic pressure and gasdynamic pressure have to match inside the cavity.

Parmentier, N.↗

NASA NTRS1979

Exploratory investigation of the effect of porous surfaces on hypersonic turbulent boundary layers

Four different test surfaces were studied to determine the effect of porous walls on the characteristics of a hypersonic turbulent flat-plate boundary layer. The investigation was an attempt to decrease the surface shear of the boundary layer by transmitting fluctuating pressure energy through the wall and absorbing it in a cavity beneath the wall. Pitot surveys were made at two locations, schlieren photographs of the boundary layer were taken, and hot-wire measurements in the flow above the boundary layer were made to determine whether the surfaces affected the turbulent boundary layer. Neither an increase nor a decrease in surface shear or boundary-layer growth was detected. Tabulations of the pitot data are included.

Watson, R. D.↗

NASA NTRS1991

Investigations of ice formation in the Space Shuttle Main Engine 0209 main injector coolant cavity

Severe main combustion chamber wall and main injector baffle element deterioration occurred during tests of Space Shuttle Main Engine 0209. One of the possible causes considered is ice formation and blockage of coolant to these components, resulting from the mixing of leaking hot turbine exhaust gas (hydrogen rich steam) and hydrogen coolant in the injector coolant cavity. The plausibility of ice blockage is investigated through simple mixing calculations for hot gas and hydrogen, investigation of condensation and water droplet formation, calculation of the freezing times for droplets, and the prediction of ice layer thicknesses. It is concluded that condensation and droplet formation can occur, and small water droplets that form can freeze very quickly when in contact with the cold coolant cavity surfaces. Copnservative analysis predicts, however, that the maximum thickness of the ice layers formed is too small to result in significant blockage of the coolant flow.

Richards, D. R.↗

NASA NTRS2007

Experimental Study of an Axisymmetric Dual Throat Fluidic Thrust Vectoring Nozzle for Supersonic Aircraft Application

An axisymmetric version of the Dual Throat Nozzle concept with a variable expansion ratio has been studied to determine the impacts on thrust vectoring and nozzle performance. The nozzle design, applicable to a supersonic aircraft, was guided using the unsteady Reynolds-averaged Navier-Stokes computational fluid dynamics code, PAB3D. The axisymmetric Dual Throat Nozzle concept was tested statically in the Jet Exit Test Facility at the NASA Langley Research Center. The nozzle geometric design variables included circumferential span of injection, cavity length, cavity convergence angle, and nozzle expansion ratio for conditions corresponding to take-off and landing, mid climb and cruise. Internal nozzle performance and thrust vectoring performance was determined for nozzle pressure ratios up to 10 with secondary injection rates up to 10 percent of the primary flow rate. The 60 degree span of injection generally performed better than the 90 degree span of injection using an equivalent injection area and number of holes, in agreement with computational results. For injection rates less than 7 percent, thrust vector angle for the 60 degree span of injection was 1.5 to 2 degrees higher than the 90 degree span of injection. Decreasing cavity length improved thrust ratio and discharge coefficient, but decreased thrust vector angle and thrust vectoring efficiency. Increasing cavity convergence angle from 20 to 30 degrees increased thrust vector angle by 1 degree over the range of injection rates tested, but adversely affected system thrust ratio and discharge coefficient. The dual throat nozzle concept generated the best thrust vectoring performance with an expansion ratio of 1.0 (a cavity in between two equal minimum areas). The variable expansion ratio geometry did not provide the expected improvements in discharge coefficient and system thrust ratio throughout the flight envelope of typical a supersonic aircraft. At mid-climb and cruise conditions, the variable geometry design compromised thrust vector angle achieved, but some thrust vector control would be available, potentially for aircraft trim. The fixed area, expansion ratio of 1.0, Dual Throat Nozzle provided the best overall compromise for thrust vectoring and nozzle internal performance over the range of NPR tested compared to the variable geometry Dual Throat Nozzle.

Flamm, Jeffrey D.↗

NASA NTRS1975

On the oxygen and nitrogen enhancements observed in low energy cosmic rays

Fisk et al. (1974) have suggested that neutral particles are ionized in the solar cavity, are subsequently picked up by the solar wind, obtaining energies of about 1 keV/nucleon, and may be further accelerated to about 10 MeV/nucleon in the interplanetary medium. The requirements for this acceleration are examined, and a possible acceleration model is outlined. The acceleration must be performed in a time less than the dwell time of the interstellar ions in the solar cavity and must compete successfully against adiabatic cooling. The energy required for the acceleration must be less than the energy available in variations in the solar wind flow. The accelerator must act inefficiently on solar wind electrons and protons, and perhaps upon the majority of interstellar ions. It is shown that these requirements can be satisfied by a model in which acceleration results from transit-time damping of long-wavelength magnetosonic turbulence.

Fisk, L. A.↗

NASA NTRS2010

Active Control of Open Cavities

Open loop edge blowing was demonstrated as an effective method for reducing the broad band and tonal components of the fluctuating surface pressure in open cavities. Closed loop has been successfully applied to low Mach number open cavities. Need to push actuators that are viable for closed loop control in bandwidth and output. Need a better understanding of the effects of control on the flow through detailed measurements so better actuation strategies can be developed.

UKeiley, Lawrence↗

NASA NTRS2017

Non-Intrusive Velocity Measurements with MTV During DCC Event in the HTTF

Velocity profiles are measured using molecular tagging velocimetry (MTV) in the high temperature test facility (HTTF) at Oregon State University during a depressurized conduction cooldown (DCC) event. The HTTF is a quarter scale electrically heated nuclear reactor simulator designed to replicate various accident scenarios. During a DCC, a double ended guillotine break results in the reactor pressure vessel (RPV) depressurizing into the reactor cavity and ultimately leading to air ingress in the reactor core (lock-exchange and gas diffusion). It is critical to understand the resulting buoyancy-driven flow to characterize the reactor self-cooling capacity through natural circulation. During tests conducted at ambient pressure and temperature, the RPV containing helium is opened (via the hot and cold legs) to a large vessel filled with nitrogen to simulate the atmosphere. The velocity profile on the hot leg pipe centerline is recorded at 10 Hz with MTV based on NO tracers. The precision of the velocimetry was measured to be 0.02 m/s in quiescent flow prior to the tests. A helium flow from the RPV is initially observed in the top quarter of the pipe. During the first 20 seconds of the event, helium flows out of the RPV with a maximum velocity below 2 m/s. The velocity profile transitions from parabolic to linear in character and decays slowly over the rest of the recording; peak velocities of 0.2 m/s are observed after 30 min. A counter-flow of nitrogen is also observed intermittently, which occurs at lower velocities (>0.1 m/s).

Andre, M. A.↗

NASA NTRS2022

Comparison of Computational Predictions of the Mach 0.80 Transonic Truss-Braced Wing Configuration with Experimental Data

The NASA Langley and Ames Research Centers have teamed together for comparisons of computational predictions of the Boeing Mach 0.80Transonic Truss-Braced Wing (TTBW) configuration with a high-speed experimental dataset. The Mach 0.80 TTBW vehicle is a high wing, high aspect ratio configuration, designed for a high lift-to-drag ratio. System studies have predicted significant fuel burn and emissions benefits with the TTBW technology moving toward meeting NASA Subsonic Transport Systems-Level-Metrics. A 4.5% scale Mach 0.80 design TTBW model was recently tested at the NASA Ames Research Center 11-by 11-Foot Transonic Wind Tunnel(11-Ft TWT),providing a valuable dataset to validate computational tools and investigate best practices as risk reduction efforts continue for the development of the advanced TTBW vehicle. The NASA Computational Fluid Dynamics (CFD) team has computed free-air flow solutions on the Mach 0.80 design flight configuration and two wind tunnel configuration variants using the USM3D and LAVA flow solvers. Accurate modeling of the configuration tested in the wind tunnel environment is critical to validating the CFD tools, thus the team has included the internal cavity region and sting in their modeling of the configuration, similar to that tested in the 11-Ft TWT. Overall, the CFD simulations compared well and show similar trends as the corrected experimental data for lift and drag polars. The CFD predicted lift curve is shifted in angle of attack from what was observed in the experiment. The shift in lift also was seen in the pitching moment comparison plots. CFD solutions were computed at constant CL test point values and showed overall very good agreement when comparing constant spanwise cuts of pressure coefficient data on the wing and strut with experimental data. CFD cavity corrections were also investigated using the 11-Ft TWT cavity correction method, similar to that used to correct the wind tunnel data. Results showed some improvement in pitching moment coefficient predictions, and an increase in drag, shifting the data to the right in drag polars, further from the experimental data at lower lift conditions, good agreement near the design CL, and slight improvement at the higher lift conditions.

Transonic Truss-Braced Wing↗

NASA NTRS1987

Bipolar flows, molecular gas disks, and the collapse and accretion of rotating interstellar clouds

Rigorous numerical models of the collapse and accretion of rotating, axisymmetric, isothermal interstellar clouds are studied. The results show that molecular gas disks and evacuated bipolar cavities both appear to be natural consequences of the collapse of rotating interstellar clouds. Dynamically significant magnetic fields may not be necessary for explaining either phenomenon. The models strongly support theoretical models of the type where an isotropic wind from a pre-main sequence star is extrinsically collimated by a rotationally derived molecular gas cloud. The models imply that collimation should be strongest on small scales where rotational effects are most important, i.e., in the dense region of the molecular gas disk.

Boss, Alan P.↗

NASA NTRS1982

Conversion of blackbody radiation into laser energy

By employing detailed kinetic models, three concepts which utilize a blackbody cavity for the conversion of solar energy into laser energy using a CO2 lasant are analyzed and compared. In the first, the blackbody radiation is used to excite flowing CO2 directly. The second and third employ a mixing laser concept with CO and N2 being the donor gases. The CO is optically pumped while thermal heating excites the N2. Blackbody temperatures ranging from 1500 deg K - 2500 deg K are considered. Based on calculated laser power output per unit flow rate of CO2, it appears that the N2-CO2 mixing laser is the most attractive system.

Mcinville, R. M.↗

NASA NTRS2006

The Design of a High-Q, MACH-5 Nozzle for the Langley 8-Foot HTT

A new nozzle has ben designed for the NASA Langley Research Center 8-Foot High Temperature Tunnel. The new nozzle was designed with a Mach-5 exit flow at a Mach-5 flight-enthalpy test condition and has a smaller throat area than the existing Mach-5 nozzle which significantly increases the range of dynamic pressures that can be achieved in the facility. The nozzle was designed using the NASA Langley IMOCND computer program which solves the potential equation using the classical method of characteristics. Several axisymmetric nozzle contours were generated and evaluated using viscous computational fluid dynamics. A number of items were considered in the evaluation, including flow uniformity, thermal and structural design, manufacturing schedule and cost. Once the final contour was selected, studies were done to determine the effects of manufacturing irregularities (steps and cavities at joints). These studies were done to develop manufacturing specifications and assembly tolerances.

Gaffey, Richard L., Jr.↗

NASA NTRS1972

A review of the Grumman orbiter wind tunnel heat transfer tests

Tests were conducted in the NASA Langley continuous flow, variable density and Mach 20 helium tunnels. The orbiter was tested alone and with various side and tandem mounted tanks. Test conditions spanned a Reynolds number range which resulted in both laminar and turbulent flows. Experimental studies also examined the heat transfer problems associated with integration of the auxiliary propulsion system into the orbiter. Tests in the hypersonic shock tunnel investigated heating to cavities and heating from single and multiple hydrogen-oxygen plumes while tests, run as part of the configuration evaluation, examined the heating to wing pods.

Mendelsohn, A. R.↗

NASA NTRS1974

Finite amplitude waves in two-dimensional lined ducts

A second-order uniform expansion is obtained for nonlinear wave propagation in a two-dimensional duct lined with a point-reacting acoustic material consisting of a porous sheet followed by honeycomb cavities and backed by the impervious wall of the duct. The waves in the duct are coupled with those in the porous sheet and the cavities. An analytical expression is obtained for the absorption coefficient in terms of the sound frequency, the physical properties of the porous sheet, and the geometrical parameters of the flow configuration. The results show that the nonlinearity flattens and broadens the absorption vs. frequency curve, irrespective of the geometrical dimensions or the porous material acoustic properties, in agreement with experimental observations.

Nayfeh, A. H.↗