Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Wing-alone aerodynamic characteristics at high angles of attack

An experimental investigation has been conducted to determine wing-alone supersonic aerodynamic characteristics at high angles of attack. The family of wings tested varied in aspect ratio from 0.5 to 4.0 and taper ratio from 0.0 to 1.0. The wings were tested at angles of attack ranging from 0 to 60 deg and Mach numbers from 1.6 to 4.6. The aerodynamic characteristics were obtained by integrating local pressures measured over the wing surface. Comparison of these data with the limited available data from the literature indicate the present data are free of sting interference effects through the test range of angle of attack. Presented and discussed are results showing the effects of model geometry, Mach number and angle of attack on aerodynamic characteristics consisting of normal force, pitching moment, bending moment, longitudinal center-of-pressure locations, and lateral center-of-pressure locations.

Stallings, R. L., Jr.↗
NASA NTRS1985

The mechanism of erosion of metallic materials under cavitation attack

The mean depth of penetration rates (MDPRs) of eight polycrystalline metallic materials, Al 6061-T6, Cu, brass, phosphor bronze, Ni, Fe, Mo, and Ti-5Al-2.5Sn exposed to cavitation attack in a viscous mineral oil with a 20 kHz ultrasonic oscillator vibrating at 50 micron amplitude are reported. The titanium alloy followed by molybdenum have large incubation periods and small MDPRs. The incubation periods correlate linearly with the inverse of hardness and the average MDPRs correlate linearly with the inverse of tensile strength of materials. The linear relationships yield better statistical parameters than geometric and exponential relationships. The surface roughness and the ratio of pit depth to pit width (h/a) increase with the duration of cavitation attack. The ratio h/a varies from 0.1 to 0.8 for different materials. Recent investigations (20) using scanning electron microscopy to study deformation and pit formation features are briefly reviewed. Investigations with single crystals indicate that the geometry of pits and erosion are dependent on their orientation.

Rao, B. C. S.↗
NASA NTRS1989

Feasibility study of vortex interaction control on a chine forebody/delta wing configuration at high angles of attack

The feasibility of controlling vortex interactions or merger on a blended chine forebody and delta wing configuration was experimentally investigated. Low-speed wind tunnel diagnostics using smoke visualizations and wing upper-surface pressure measurements were performed on a generic 60 deg delta and chine forebody model, to assess chine modifications and leading edge flaps. Both techniques were shown to promote uncoupled vortex flows at high angles of attack and sideslip, with significant influence on the wing flow field, indicating potential for alleviating adverse high-alpha characteristics of blended chine swept wing configurations.

Rao, Dhanvada M.↗
NASA NTRS1960

The Blunt Plate In Hypersonic Flow

The sonic-wedge characteristics method has been used to obtain the shock shapes and surface pressure distributions on several blunt two-dimensional shapes in a hypersonic stream for several values of the ratio of specific heats. These shapes include the blunt slab at angle of attack and power profiles of the form yb = a)P, where 0 les than m less than 1, Yb and x are coordinates of the body surface, and a is a constant. These numerical results have been compared with the results of blast-wave theory, and methods of predicting the pressure distributions and shock shapes are proposed in each case. The effects of a free-stream conical-flow gradient on the pressure distribution on a blunt slab in hypersonic flow were investigated by the sonic-wedge characteristics method and were found to be sizable in many cases. Procedures which are satisfactory for reducing pressure data obtained in conical flows with small gradients are presented.

Baradell, Donald L.↗
NASA NTRS1950

Free-Flight Investigation of the Static and Dynamic Longitudinal Stability Characteristics of 1/3.7-Scale Rocket-Powered Models of the Bell MX-776A

An investigation of the static and dynamic longitudinal stability characteristics of 1/3.7 scale rocket-powered model of the Bell MX-776A has been made for a Mach number range from 0.8 to 1.6. Two models were tested with all control surfaces at 0 degree deflection and centers of gravity located 1/4 and 1/2 body diameters, respectively, ahead of the equivalent design location. Both models were stable about the trim conditions but did not trim at 0 degree angle of attack because of slight constructional asymmetries. The results indicated that the variation of lift and pitching moment was not linear with angle of attack. Both lift-curve slope and pitching-moment-curve slope were of the smallest magnitude near 0 degree angle of attack. In general, an increase in angle of attack was accompanied by a rearward movement of the aerodynamic center as the rear wing moved out of the downwash from the forward surfaces. This characteristic was more pronounced in the transonic region. The dynamic stability in the form of total damping factor varied with normal-force coefficient but was greatest for both models at a Mach number of approximately 1.25. The damping factor was greater at the lower trim normal-force coefficients except at a Mach number of 1.0. At that speed the damping factor was of about the same magnitude for both models. The drag coefficient increased with trim normal-force coefficient and was largest in the transonic region.

Michal, David H.↗
DOE OSTI2024

PRISTINE: An Emulation Platform for PCB-Level Hardware Trojans

Printed circuit Boards (PCBs) are becoming increasingly vulnerable to malicious design alteration, also known as Trojan attacks, due to a distributed business model that often involves various untrusted parties. Such attacks can be mounted at various stages in the PCB life cycle. The relative ease of alteration of PCB hardware even after fabrication (due to physical access to surface-mounted critical components and traces) makes them attractive for an adversary to manipulate their functional/physical behavior for malicious intent. There is a growing need to explore viable Trojan attacks in a PCB, analyze their functional and physical characteristics (e.g., impact on power or delay), and study the effectiveness of countermeasures against these attacks. While simulation-based approaches for PCB Trojan insertion are effective at creating a large population of possible Trojans, they fail to provide functional feasibility analysis with a realistic workload for a trigger circuit. Also, they cannot estimate a Trojan’s side-channel footprint due to the unavailability of physical models of diverse PCB components. To address these deficiencies, in this paper, we present PRISTINE, a PCB-level emulation system for any integrity or physical tampering issues, specifically, hardware Trojan insertion. The need for building such an emulation platform to resolve PCB trust issues in the supply chain is also surveyed and discussed. Both custom Hardware Hacking (HaHa) boards and multiple commercial PCBs are then used to test the ability of the proposed system to emulate various hardware Trojans specially designed to exploit board-specific hardware characteristics. Experimental results on emulated board-level Trojans show that a wide range of Trojans can be successfully activated, thus enabling the expected payload effects on both types of boards to be studied and quantified. The resulting data are further analyzed to create PCB-level Trojan benchmarks. In particular, a comparative evaluation of the experimental results is used to propose a risk level metric that quantifies the probability of detection and degree of payload impact of each Trojan on a given commercial PCB.

47 OTHER INSTRUMENTATION↗
NASA NTRS1986

A comparison of experimental and numerical results for delta wings with vortex flaps

Computational and experimental results are presented for delta wings with vortex flaps. The wings have an undeflected leading-edge sweep of 75 deg. Flap angles of 5 deg and 10 deg, measured in the streamwise direction, are considered. The nominal angle of attack alpha is varied from 4 deg to 12 deg. Results for freestream Mach numbers of 1.7 and 2.4 are shown. Surface pressure, tuft patterns and vapor screens are given for the experimental data. Surface pressure, tuft patterns, cross-flow velocities, total pressure loss and cross-flow Mach number are given for the numerical data. C(l)-vs-alpha curves are shown for experimental and computational results. The flows are shown to be very sensitive to angle of attack, and the agreement between experimental and theoretical results is improved if the calculations are made at angles of attack slightly larger than the experimental angles of attack. The computational model correctly predicts the topology of the flow in each of the cases considered. The lift is predicted well at the higher angles of attack, but slightly overpredicted at the lower angles of attack.

Powell, K. G.↗
NASA NTRS2004

LASTRAC.3d: Transition Prediction in 3D Boundary Layers

Langley Stability and Transition Analysis Code (LASTRAC) is a general-purpose, physics-based transition prediction code released by NASA for laminar flow control studies and transition research. This paper describes the LASTRAC extension to general three-dimensional (3D) boundary layers such as finite swept wings, cones, or bodies at an angle of attack. The stability problem is formulated by using a body-fitted nonorthogonal curvilinear coordinate system constructed on the body surface. The nonorthogonal coordinate system offers a variety of marching paths and spanwise waveforms. In the extreme case of an infinite swept wing boundary layer, marching with a nonorthogonal coordinate produces identical solutions to those obtained with an orthogonal coordinate system using the earlier release of LASTRAC. Several methods to formulate the 3D parabolized stability equations (PSE) are discussed. A surface-marching procedure akin to that for 3D boundary layer equations may be used to solve the 3D parabolized disturbance equations. On the other hand, the local line-marching PSE method, formulated as an easy extension from its 2D counterpart and capable of handling the spanwise mean flow and disturbance variation, offers an alternative. A linear stability theory or parabolized stability equations based N-factor analysis carried out along the streamline direction with a fixed wavelength and downstream-varying spanwise direction constitutes an efficient engineering approach to study instability wave evolution in a 3D boundary layer. The surface-marching PSE method enables a consistent treatment of the disturbance evolution along both streamwise and spanwise directions but requires more stringent initial conditions. Both PSE methods and the traditional LST approach are implemented in the LASTRAC.3d code. Several test cases for tapered or finite swept wings and cones at an angle of attack are discussed.

Chang, Chau-Lyan↗
NASA NTRS1978

Effects of service environments on aluminum-brazed titanium (ABTi)

Aluminum brazed titanium (ABTi) structures were evaluated during prolonged exposure to extreme environments: elevated temperature exposure to airline service fluids, hydraulic fluid, and seawater, followed by laboratory corrosion tests. Solid-face and perforated face honeycomb sandwich panel specimens, stressed panel assemblies, and faying surface brazed joints were tested. The corrosion resistance of ABTi is satisfactory for commercial airline service. Unprotected ABTi proved inherently resistant to attack by all of the extreme service aircraft environments except: seawater at 700 K (800 F) and above, dripping phosphate ester hydraulic fluid at 505 K (450 F), and a marine environment at ambient temperature. The natural oxides and deposits present on titanium surfaces in airline service provide protection against hot salt corrosion pitting. Coatings are required to protect titanium dripping phosphate ester fluid at elevated temperatures and to protect exposed acoustic honeycomb parts against corrosion in a marine environment.

Cotton, W. L.↗
NASA NTRS1995

Progress in Navier-Stokes Simulation of Delta Wing Maneuver Aerodynamics

This paper will summarize recent progress in the numerical simulation of high incidence vortical flow about a generic 65 degree sweep delta wing using the three dimensional, time-dependent, Reynolds averaged, Navier-Stokes (RANS) equations. Computations have been carried out at 15 and 30 degrees angle of attack under subsonic turbulent flow conditions, and compared with experimental data provided by Hanff, Jenkins, and their colleagues. This work has already been published elsewhere and widely disseminated. Computations carried out at 15 degrees angle of attack included static roll angles ranging up to 65 degrees, and a large-amplitude (40 degree), high rate (7 Hz), forced roll motion. There was very good agreement between computed and experimental forces and moments, and static surface pressures. There was a significant hysteresis of the dynamic rolling moment due to the high rate of roll motion. At this angle of attack, no vortex breakdown was observed in the computations or experiment. Computations were also carried out at 30 degrees angle of attack, where vortex breakdown was present in both the computations and experiment. There was overall good agreement in the computed and experimental forces and moments. The static rolling moment varied with roll angle in a highly nonlinear manner, and exhibited three stable trim points and two unstable trim points. This behavior was attributed to the presence of vortex breakdown. Two large-amplitude (30 degrees), high-rate (10 Hz) forced roll motions were computed. The dynamics of the vortex breakdown motion was dramatically visualized by tracking the time-dependent motion of particles released near the delta wing apex. This numerical visualization is analogous to experimental smoke flow techniques. In one of the dynamic cases the breakdown was found to move off the wing, convected downwind of the trailing edge, and later reformed near the trailing edge through an instability of the vortex core. A damped free-to-roll motion was also computed by releasing the wing from rest at 40 degrees of roll. The wing went to the same trim point as in the experiment.

Chaderjian, Neal M.↗
NASA NTRS1961

Wind-Tunnel Tests of Seven Static-Pressure Probes at Transonic Speeds

Wind-tunnel tests have been conducted to determine the errors of 3 seven static-pressure probes mounted very close to the nose of a body of revolution simulating a missile forebody. The tests were conducted at Mach numbers from 0.80 to 1.08 and at angles of attack from -1.7 deg to 8.4 deg. The test Reynolds number per foot varied from 3.35 x 10(exp 6) to 4.05 x 10(exp 6). For three 4-vane, gimbaled probes, the static-pressure errors remained constant throughout the test angle-of-attack range for all Mach numbers except 1.02. For two single-vane, self-rotating probes having two orifices at +/-37.5 deg. from the plane of symmetry on the lower surface of the probe body, the static-pressure error varied as much as 1.5 percent of free-stream static pressure through the test angle-of- attack range for all Mach numbers. For two fixed, cone-cylinder probes of short length and large diameter, the static-pressure error varied over the test angle-of-attack range at constant Mach numbers as much as 8 to 10 percent of free-stream static pressure.

Capone, Francis J.↗
NASA NTRS1990

Analytical method for the ditching analysis of an airborne vehicle

A simple analytical method has been introduced for aerohydrodynamic load analysis of an airborne configuration during water ditching. The method employs an aerodynamic panel code, based on linear potential flow theory, to simulate the flow of air and water around an aircraft configuration. The free surface separating the air and water region is represented by doublet" singularities. Although all the theoretical load distributions are computed for air, provisions are made to correct the pressure coefficients obtained on the configuration-wetted surfaces to account for the water density. As an analytical tool, a vortex aerodynamic code is chosen to carry out the present investigation. After assessing· the validity of the method, an application is presented for the water ditching of the Space Shuttle configuration at a 12-deg attitude.

Pressure coefficient↗
NASA NTRS1973

Flight-measured X-24A lifting body control surface hinge moments and correlation with wind tunnel predictions

Control-surface hinge-moment measurements obtained in the X-24A lifting body flight-test program are compared with results from wind-tunnel tests. The effects of variations in angle of attack, angle of sideslip, rudder bias, rudder deflection, upper-flap deflection, lower-flap deflection, Mach number, and rocket-engine operation on the control-surface hinge moments are presented. In-flight motion pictures of tufts attached to the inboard side of the right fin and the rudder and upper-flap surfaces are discussed.

Tang, M. H.↗
NASA NTRS1982

Three-dimensional flows about simple components at angle of attack

The structures of three dimensional separated flow about some chosen aerodynamic components at angle of attack are synthesized, holding strictly to the notion that streamlines in the external flow (viscous plus inviscid) and skin friction lines on the body surface may be considered as trajectories having properties consistent with those of continuous vector fields. Singular points in the fields are of limited number and are classified as simple nodes and saddles. Analogous flow structures at high angles of attack about blunt and pointed bodies, straight and swept wings, etc., are discussed, highlighting the formation of spiral nodes (foci) in the pattern of the skin friction lines. How local and global three dimensional separation lines originate and form is addressed, and the characteristics of both symmetric and asymmetric leeward wakes are described.

Peake, D. J.↗
NASA NTRS1982

Three-dimensional flows about simple components at angle of attack

The structures of three dimensional separated flow about some chosen aerodynamic components at angle of attack are synthesized, holding strictly to the notion that streamlines in the external flow (viscous plus inviscid) and skin friction lines on the body surface may be considered as trajectories having properties consistent with those of continuous vector fields. Singular points in the fields are of limited number and are classified as simple nodes and saddles. Analogous flow structures at high angles of attack about blunt and pointed bodies, straight and swept wings, etc., are discussed, highlighting the formation of spiral nodes (foci) in the pattern of the skin friction lines. How local and global three dimensional separation lines originate and form is addressed, and the characteristics of both symmetric and asymmetric leeward wakes are described.

Peake, D. J.↗
NASA NTRS1988

An analytical method for the ditching analysis of an airborne vehicle

A simple analytical method has been introduced for aerohydrodynamic load analysis of an airborne configuration during water ditching. The method employs an aerodynamic panel code, based on linear potential flow theory, to simulate the flow of air and water around an aircraft configuration. The free surface separating the air and water region is represented by doublet sheet singularities. Although all the theoretical load distributions are computed for air, provisions are made to correct the pressure coefficients obtained on the configuration wetted surfaces to account for the water density. As an analytical tool, the Vortex Separation Aerodynamic (VSAERO) code is chosen to carry out the present investigation. After assessing the validity of the method, its first application is to analyze the water ditching of the Space Shuttle configuration at a 12 degree attitude.

Pressure coefficient↗
NASA NTRS2012

Investigation of Hypersonic Laminar Heating Augmentation in the Stagnation Region

Laminar stagnation region heating augmentation is investigated in the AEDC Tunnel 9 at Mach 10 by performing high frequency surface pressure and heat transfer measurements on the Orion CEV capsule at zero degree angle-of-attack for unit Reynolds numbers between 0.5 and 15 million per foot. Heating augmentation increases with Reynolds number, but is also model size dependent as it is absent on a 1.25-inch diameter model at Reynolds numbers where it reaches up to 15% on a 7-inch model. Heat transfer space-time correlations on the 7-inch model show that disturbances convect at the boundary layer edge velocity and that the streamwise integral scale increases with distance. Therefore, vorticity amplification due to stretching and piling-up in the stagnation region appears to be responsible for the stagnation point heating augmentation on the larger model. This assumption is reinforced by the f(exp -11/3) dependence of the surface pressure spectrum compared to the f(exp -1) dependence in the free stream. Vorticity amplification does not occur on the 1.25- inch model because the disturbances are too large. Improved free stream fluctuation measurements will be required to determine if significant vorticity is present upstream or mostly generated behind the bow shock.

Marineau, Eric C.↗
NASA NTRS2001

CFD Simulations in Support of Shuttle Orbiter Contingency Abort Aerodynamic Database Enhancement

Modern Computational Fluid Dynamics (CFD) techniques were used to compute aerodynamic forces and moments of the Space Shuttle Orbiter in specific portions of contingency abort trajectory space. The trajectory space covers a Mach number range of 3.5-15, an angle-of-attack range of 20deg-60deg, an altitude range of 100-190 kft, and several different settings of the control surfaces (elevons, body flap, and speed brake). Presented here are details of the methodology and comparisons of computed aerodynamic coefficients against the values in the current Orbiter Operational Aerodynamic Data Book (OADB). While approximately 40 cases have been computed, only a sampling of the results is provided here. The computed results, in general, are in good agreement with the OADB data (i.e., within the uncertainty bands) for almost all the cases. However, in a limited number of high angle-of-attack cases (at Mach 15), there are significant differences between the computed results, especially the vehicle pitching moment, and the OADB data. A preliminary analysis of the data from the CFD simulations at Mach 15 shows that these differences can be attributed to real-gas/Mach number effects. The aerodynamic coefficients and detailed surface pressure distributions of the present simulations are being used by the Shuttle Program in the evaluation of the capabilities of the Orbiter in contingency abort scenarios.

Papadopoulos, Periklis E.↗