Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

F-8 supercritical wing flight pressure, Boundary layer, and wake measurements and comparisons with wind tunnel data

Data for speeds from Mach 0.50 to Mach 0.99 are presented for configurations with and without fuselage area-rule additions, with and without leading-edge vortex generators, and with and without boundary-layer trips on the wing. The wing pressure coefficients are tabulated. Comparisons between the airplane and model data show that higher second velocity peaks occurred on the airplane wing than on the model wing. The differences were attributed to wind tunnel wall interference effects that caused too much rear camber to be designed into the wing. Optimum flow conditions on the outboard wing section occurred at Mach 0.98 at an angle of attack near 4 deg. The measured differences in section drag with and without boundary-layer trips on the wing suggested that a region of laminar flow existed on the outboard wing without trips.

Montoya, L. C.↗
NASA NTRS1977

Effects of deflected thrust on the longitudinal aerodynamic characteristics of a close-coupled wing-canard configuration

The effects of power on the longitudinal aerodynamic characteristics of a close-coupled wing-canard fighter configuration with partial-span rectangular nozzles at the trailing edge of the wing were investigated. Data were obtained on a basic wing-strake configuration for nozzle and flap deflections from 0 deg to 30 deg and for nominal thrust coefficients from 0 to 0.30. The model was tested over an angle-of-attack range from -2 deg to 40 deg at Mach numbers of 0.15 and 0.18. Results show substantial improvements in lift-curve slope, in maximum lift, and in drag-due-to-lift efficiency when the canard and strakes have been added to the basic wing-fuselage (wing-alone) configuration. Addition of power increased both lift-curve slope and maximum lift, improved longitudinal stability, and reduced drag due to lift on both the wing-canard and wing-canard-strake configurations. These beneficial effects are primarily derived from boundary-layer control due to moderate thrust coefficients which delay flow separation on the nozzle and inboard portion of the wing flaps.

Yip, L. P.↗
NASA NTRS1981

Overview of advanced wing design

Examples of experiment theory correlation are presented to give an indication of the capabilities and limitations of wing design and analysis for transonic applications by potential flow theory. The examples include correlations of experimental pressure distributions with theoretical results from isolated wing codes and wing-body codes. Both conservative and non conservative differencing as well as body and boundary layer corrections are considered. A full potential isolated wing code correlates well with data from an isolated wing test but may give poor prediction of the aerodynamic characteristics of some wing-body configurations. Potential flow wing body codes were found to improve the correlation for the wing-body configurations considered.

Hicks, R. M.↗
NASA NTRS1981

Experimental and theoretical study of three interacting, closely-spaced, sharp-edged 60 deg delta wings at low speeds

Wind tunnel tests were conducted to determine the subsonic longitudinal aerodynamic characteristics of lifting configuration consisting of a 60 deg delta main wing with two smaller 60 deg delta wings (called sub-wings) attached underneath. The test was designed to determine the effects on lift, drag, and pitching moment due to various placement of the subwings in relation to the main wing. Test results indicate the increasing vertical separation between the main wing and the sub-wings produced the most significant results; a 23.1% increase in maximum lift coefficient, a reduction in drag coefficient at high lift coefficients, and an increase in longitudinal stability. Lateral separation of the sub-wings produced no significant changes. Placement of the sub-wings rearward increases the initial lift curve slope and maximum lift coefficient and also increase the longitudinal stability. Results of a computer study using a vortex lattice code supported the experimental conclusions.

Faery, H. F., Jr.↗
NASA NTRS1981

Transonic wing design using potential-flow codes - Successes and failures

The state-of-the-art of transonic wing design by use of computer codes based on the potential flow-theory is presented. The capabilities and limitations of these codes are exemplified by several experiment-theory correlations, including an assessment of pressure distribution from isolated wing and wing-body codes. Computer codes using both conservative and nonconservative differencing schemes were used, and the effects of boundary-layer corrections were considered. Results showed that calculations from a full potential, isolated code correlate well with data from an isolated wing test, but may give poor predictions of the aerodynamic characteristics of some wing-body configurations. Boundary-layer correlations were found to have only moderate effects on experiment-theory correlation. Aeroelastic effects were considered important for high aspect ratio wings of low to moderate thickness, and viscous effects were minimal for typical cruise conditions, even for Reynold's numbers as low as two million. The effect of wind-tunnel walls on experiment-theory correlations remained inconclusive. A wing-body code was used to calculate the flow field about a wing-body configuration with body-mounted engines, typical of the transonic Biz-Jet aircraft.

Hicks, R. M.↗
NASA NTRS1982

Automated optimum design of wing structures. Deterministic and probabilistic approaches

The automated optimum design of airplane wing structures subjected to multiple behavior constraints is described. The structural mass of the wing is considered the objective function. The maximum stress, wing tip deflection, root angle of attack, and flutter velocity during the pull up maneuver (static load), the natural frequencies of the wing structure, and the stresses induced in the wing structure due to landing and gust loads are suitably constrained. Both deterministic and probabilistic approaches are used for finding the stresses induced in the airplane wing structure due to landing and gust loads. A wing design is represented by a uniform beam with a cross section in the form of a hollow symmetric double wedge. The airfoil thickness and chord length are the design variables, and a graphical procedure is used to find the optimum solutions. A supersonic wing design is represented by finite elements. The thicknesses of the skin and the web and the cross sectional areas of the flanges are the design variables, and nonlinear programming techniques are used to find the optimum solution.

Rao, S. S.↗
NASA NTRS1982

Wind tunnel tests of a free-wing/free-trimmer model

The riding qualities of an aircraft with low wing loading can be improved by freeing the wing to rotate about its spanwise axis. A trimming surface also free to rotate about its spanwise axis can be added at the wing tips to permit the use of high lift devices. Wind tunnel tests of the free wing/free trimmer model with the trimmer attached to the wing tips aft of the wing chord were conducted to validate a mathematical model developed to predict the dynamic characteristics of a free wing/free trimmer aircraft. A model consisting of a semispan wing with the trimmer mounted on with the wing on an air bearing and the trimmer on a ball bearing was displaced to various angles of attack and released. The damped oscillations of the wing and trimmer were recorded. Real and imaginary parts of the characteristic equations of motion were determined and compared to values predicted using the mathematical model.

Sandlin, D. R.↗
NASA NTRS1983

Aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed with forward-swept wings and canards

The Langley 16 foot transonic tunnel was used to determine the aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed in a wing-body configuration with forward-swept wings. The configuration was tested with and without fixed canards. The test conditions included free-stream Mach numbers of 0.60, 0.90, and 1.20. The model angle of attack ranged from -2 deg to 14 deg; the nozzle pressure ratio ranged from 1.0 (jet off) to 9.0. The Reynolds number based on the wing mean aerodynamic chord varied from 3.0 x 10 to the 6th power to 4.8 x 10 to the 6th power, depending on Mach number. Aerodynamic characteristics were analyzed to determine the effects of thrust vectoring and the canard effects on the wing-afterbody-nozzle and the wing-afterbody portions of the model. Thrust vectoring had no effect on the angle of attack for the onset of flow separation on the wing but resulted in reduced drag at angle-of-attack values above that required for wing flow separation. The canard was found to have little effect on the thrust-induced lift resulting from vectoring, since canard effects occurred primarily on the wing.

Mason, M. L.↗
NASA NTRS1983

Low-speed investigation of the maneuver capability of supersonic fighter wings

A low-speed investigation of wings suitable for supersonic fighter application was undertaken to understand the flow regions developed by these wings through flow visualization and to evaluate areas in which low-speed testing could provide information for extrapolation to higher Mach numbers and Reynolds numbers. This study involved cranked wings of highly-swept inboard panels and outboard panel of various sweeps with leading- and trailing-edge devices. Both theoretical and experimental results with flow visualization are presented. Flow visualization results show that a mixed flow condition (vortex flow on the highly-swept inboard section and attached flow on the cranked outboard section) is possible for wings with low sweep (20 deg) outboard cranked sections. Lift and drag measurements on the planar (no flap deflection) wings show good agreement with theoretical results for leading-edge vortex flow. There is little or no change in planar wing performance at maneuver conditions due to outboard sweep effects. Results also show that for cambered wings (flap deflected) only small improvements in performance over flat wings were obtained at high-lift maneuver conditions.

Hom, K. W.↗
NASA NTRS1984

Numerical simulation of the tip vortex off a low-aspect-ratio wing at transonic speed

The viscous transonic flow around a low aspect ratio wing was computed by an implicit, three dimensional, thin-layer Navier-Stokes solver. The grid around the geometry of interest is obtained numerically as a solution to a Dirichlet problem for the cube. A low aspect ratio wing with large sweep, twist, taper, and camber is the chosen geometry. The topology chosen to wrap the mesh around the wing with good tip resolution is a C-O type mesh. The flow around the wing was computed for a free stream Mach number of 0.82 at an angle of attack of 5 deg. At this Mach number, an oblique shock forms on the upper surface of the wing, and a tip vortex and three dimensional flow separation off the wind surface are observed. Particle path lines indicate that the three dimensional flow separation on the wing surface is part of the roots of the tip vortex formation. The lifting of the tip vortex before the wing trailing edge is observed by following the trajectory of particles release around the wing tip.

Mansour, N. N.↗
NASA NTRS1984

The influence of leading-edge load alleviation on supersonic wing design

A theoretical and experimental program to assess the effect of leading-edge load constraints on wing design and performance was conducted. For a planform characterized by a highly swept leading edge on the inboard region, linear theory was used to design camber surfaces which produced minimum drag-due-to-lift at the design lift coefficient of 0.08 and a design Mach number of 2.4. In an effort to delay the formation of leading edge vortices which often occur on highly swept wings, two approaches were used in the design criteria to limit the loadings on the leading edge. One wing was constrained to have the normal Mach number less than one everywhere along the leading edge and the second wing was constrained to have a pressure coefficient of zero on the leading edge. Force tests were run on the two constrained wings, on a flat reference wing and on an optimized wing with no leading edge constraints. All wings had identical planforms and thicknesses and were tested over a range of Mach numbers from 1.8 to 2.8 and a range in angles of attack from -5 deg to 8 deg. A comparison of the experimental performance of these four models is shown. Correlations of these results with theoretical predictions and flow visualization photographs are also included.

Darden, C. M.↗
NASA NTRS1985

Downwash in the plane of symmetry of an elliptically loaded wing

A closed-form solution for the downwash in the plane of symmetry of an elliptically loaded line is given. This theoretical result is derived from Prandtl's lifting-line theory and assumes that: (1) a three-dimensional wing can be replaced by a straight lifting line, (2) this line is elliptically loaded, and (3) the trailing wake is a flat-sheet which does not roll up. The first assumption is reasonable for distances greater than about 1 chord from the wing aerodynamic center. The second assumption is satisfied by any combination of wing twist, spanwise camber variation, or planform that approximates elliptic loading. The third assumption is justified only for high-aspect-ratio wings at low lift coefficients and downstream distances less than about 1 span from the aerodynamic center. It is shown, however, that assuming the wake to be fully rolled up gives downwash values reasonably close to those of the flat-sheet solution derived in this paper. The wing can therefore be modeled as a single horseshoe vortex with the same lift and total circulation as the equivalent ellipticity loaded line, and the predicted downwash will be a close approximation independent of aspect ratio and lift coefficient. The flat-sheet equation and the fully rolled up wake equation are both one-line formulas that predict the upwash field in front of the wing, as well as the downwash field behind it. These formulas are useful for preliminary estimates of the complex aerodynamic interaction between two wings (i.e., canard, tandem wing, and conventional aircraft) including the effects of gap and stagger.

Phillips, J. D.↗
NASA NTRS1984

Joined-wing research airplane feasibility study

The joined wing is a new type of aircraft configuration which employs tandem wings arranged to form diamond shapes in plan view and front view. Wind-tunnel tests and finite-element structural analyses have shown that the joined wing provides the following advantages over a comparable wing-plus-tail system; lighter weight and higher stiffness, higher span-efficiency factor, higher trimmed maximum lift coefficient, lower wave drag, plus built-in direct lift and direct sideforce control capability. To verify these advantages at full scale a manned research airplane is required. A study has therefore been performed of the feasibility of constructing such an airplane, using the fuselage and engines of the existing NAA AD-1 oblique-wing airplane. Cost and schedule constraints favored converting the AD-1 rather than constructing a totally new airframe. By removing the outboard wing panels the configuration can simulate wings joined at 60, 80, or 100 percent of span. For maximum versatility the aircraft has alternative control surfaces (such as ailerons and elevators on the front and/or rear wings), and a removeable canard to explore canard/joined-wing interactions at high-lift conditions. Design, performance, and flying qualities are discussed.

Wolkovitch, J.↗
NASA NTRS1985

Theory of wing rock

Wing rock is one type of lateral-directional instabilities at high angles of attack. To predict wing rock characteristics and to design airplanes to avoid wing rock, parameters affecting wing rock characteristics must be known. A new nonlinear aerodynamic model is developed to investigate the main aerodynamic nonlinearities causing wing rock. In the present theory, the Beecham-Titchener asymptotic method is used to derive expressions for the limit-cycle amplitude and frequency of wing rock from nonlinear flight dynamics equations. The resulting expressions are capable of explaining the existence of wing rock for all types of aircraft. Wing rock is developed by negative or weakly positive roll damping, and sustained by nonlinear aerodynamic roll damping. Good agreement between theoretical and experimental results is obtained.

Hsu, C.-H.↗
NASA NTRS1985

Comparison of advanced turboprop installation on swept and unswept supercritical wings at transonic speeds

A series of wind-tunnel investigations were conducted to determine the aerodynamic interference associated with the over wing and under wing installation of a turboprop nacelle on 20 deg swept and unswept supercritical wings. The purpose of the investigations was to increase the understanding of the flow interactions involved with the nacelle turboprop integration and to obtain experimental data for the verification of computational prediction techniques. The models were tested in the Langley 16-Foot Transonic Tunnel at Mach numbers from 0.50 to 0.80 and at angles-of-attack from 0 to 5 deg. In addition, data at several propeller pitch angles and advance ratio settings were obtained. This paper which presents only the results of the over-the-wing nacelle installations shows that wing sweep had considerable influence on the installation interference. Large scale flow separation was observed on the swept wing at M = 0.8. Less severe effects were observed at M = 0.7 on the swept wing and for both M = 0.7 and 0.8 on the unswept wing.

Carlson, J. R.↗
NASA NTRS1985

A forward-swept wing configuration designed for high maneuverability by use of three-dimensional transonic theory

Supercritical technology has been applied to the design of a forward-swept-wing fighter configuration, and an assessment has been made of the relative performance of forward versus aft sweep. The wing and canard for this forward-swept wing configuration were designed for transonic maneuver by the use of a transonic computational analysis method and a transonic design procedure. The computational method calculates the transonic flow over a canard-wing-fuselage combination so that the strong transonic induced-flow effects of the canard on the wing are taken into account. A model of this configuration was constructed and was tested in the Langley 16-Foot Transonic Tunnel. The transonic theory gave a reasonably good estimate of the wing pressure distributions at transonic maneuver conditions. Comparison of this configuration with an equivalent aft-swept wing configuration showed that, at a Mach number of 0.9 and a lift coefficient of 0.9, the two configurations have essentially the same drag. This forward-swept wing configuration was also found to have very good maneuver performance relative to the Rockwell International HiMAT highly-maneuverable aircraft configuration.

Mann, M. J.↗
NASA NTRS1987

An experimental investigation of an advanced turboprop installation on a swept wing at subsonic and transonic speeds

An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of a turboprop-nacelle installation on the pressure distributions over a swept, supercritical wing. The tests were conducted at Mach numbers from 0.20 to 0.80, at angles of attack from 0 to 5 degrees, nacelle nozzle pressure ratios from 1.0 to 1.6, and at propeller tip speeds from 700 to 800 ft/sec. The results of this study indicate that the turboprop nacelle interference, with and without power, on a swept wing is greater on the inboard wing panel than on the outboard wing panel. The over-the-wing nacelle installation with the propeller upwash on the inboard panel had flow separation problems at a Mach number of 0.80. No severe flow separation problems appear to exist for either propeller rotation direction for the under-the-wing nacelle installation. The local flow disturbances caused by the under-the-wing nacelle installation were in general less severe than for the over-the-wing nacelle installation.

Carlson, John R.↗
NASA NTRS1987

Advanced turboprop wing installation effects measured by unsteady blade pressure and noise

A single rotation model propeller (SR-7A) was tested at simulated takeoff/approach conditions (Mach 0.2), in the NASA Lewis 9- by 15-Ft Anechoic Wind Tunnel. Both unsteady blade surface pressures and noise measurements were made for a tractor configuration with propeller/straight wing and propeller alone configurations. The angle between the wing chord and propeller axis (droop angle) was varied along with the wing angle of attack to determine the effects on noise and unsteady loading. A method was developed that uses unsteady blade pressure measurements to provide a quantitative indication of propeller inflow conditions, at least for a uniform (across the propeller disk) inflow angle. The wing installation caused a nearly uniform upwash at the propeller inlet as evidenced by the domination of the pressure spectra by the first shaft order. This inflow angle increased at a rate of almost 150 percent of that of the wing angle-of-attack for a propeller-wing spacing of 0.54 wing chords at a constant droop angle. The flyover noise, as measured by the maximum blade passing frequency level, correlates closely with the propeller inflow angle (approx. 0.6 dB per degree of inflow angle) for all droop angles and wing angles of attack tested, including the propeller alone data. Large changes in the unsteady pressure responses on the suction surface of the blade were observed as the advance ratio was varied. The presence of a leading edge vortex may explain this behavior since changes in the location of this vortex would change with loading (advance ratio).

Heidelberg, Laurence J.↗