Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VELOCITY MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

Development of position-sensitive time-of-flight spectrometer for fission fragment research

A position-sensitive, high-resolution time-of-flight detector for fission fragments has been developed. The SPectrometer for Ion DEtermination in fission Research (SPIDER) is a 2E–2v spectrometer designed to measure the mass of light fission fragments to a single mass unit. The time pick-off detector pairs to be used in SPIDER have been tested with α-particles from 229Th and its decay chain and α-particles and spontaneous fission fragments from 252Cf. Each detector module is comprised of thin electron conversion foil, electrostatic mirror, microchannel plates, and delay-line anodes. Particle trajectories on the order of 700 mm are determined accurately to within 0.7 mm. Flight times were measured with 250 ps resolution FWHM. Computed particle velocities are accurate to within 0.06 mm/ns corresponding to a precision of 0.5%. As a result, an ionization chamber capable of 400 keV energy resolution coupled with the velocity measurements described here will pave the way for modestly efficient measurements of light fission fragments with unit mass resolution.

2E-2v↗

Three-dimensional hydrodynamics of the deceleration stage in inertial confinement fusion

The deceleration stage of inertial confinement fusion implosions is modeled in detail using three-dimensional simulations designed to match experiments at the National Ignition Facility. In this final stage of the implosion, shocks rebound from the center of the capsule, forming the high-temperature, low-density hot spot and slowing the incoming fuel. The flow field that results from this process is highly three-dimensional and influences many aspects of the implosion. The interior of the capsule has high-velocity motion, but viscous effects limit the range of scales that develop. The bulk motion of the hot spot shows qualitative agreement with experimental velocity measurements, while the variance of the hot spot velocity would broaden the DT neutron spectrum, increasing the inferred temperature by 400–800 eV. Jets of ablator material are broken apart and redirected as they enter this dynamic hot spot. Deceleration stage simulations using two fundamentally different rad-hydro codes are compared and the flow field is found to be in good agreement.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Filamentary velocity scaling validation in the TCV tokamak

A large database of reciprocating probe data from the edge plasma of TCV (Tokamak à Configuration Variable) is used to test the radial velocity scalings of filaments from analytical theory. The measured velocities are mainly scattered between zero and a maximum velocity which varies as a function of size and collisionality in agreement with the analytical scalings. The scatter is consistent with mechanisms that tend to slow the velocity of individual filaments. While the radial velocities were mainly clustered between 0.5 and 2 km/s, a minority reached outward velocities as high as 5 km/s or inward velocities as high as –4 km/s. Inward moving filaments are only observed in regions of high poloidal velocity shear in discharges with B × ∇B away from the X-point, a new finding. Here, the filaments have diameters clustered between 3 and 11 mm, and normalized sizes $\hat{a}$ clustered between 0.3 and 1.1, such that most filaments populate the resistive-ballooning regime; therefore, most of the filaments in TCV have radial velocities with little or no dependence on collisionality. Improvements in cross-correlation techniques and conditional averaging techniques are discussed which reduce the sizes determined for the largest filaments, including those larger than the scrape-off layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Swirl, confinement and nozzle effects on confined turbulent flow

Predictions of swirl, confinement and nozzle effects on confined turbulent flow are exhibited and compared with five-hole pitot-probe time-mean velocity measurements. Two sets of computations are given, one using the standard k-epsilon turbulence model and the other using a C sub mu formulation model deduced from recent six-orientation single-wire hot-wire measurements. Results confirm that the accuracy of the latter model is superior. To highlight the effects of confinement and exit nozzle area on this flow, three expansion ratios and two contraction ratios are used. Predictions are given for a full range of swirl strengths using measured inlet conditions for axial, radial and swirl velocity profiles. The predicted velocity profiles illustrate the large-scale effects of inlet swirl on flowfields. It appears that a strong contraction nozzle has a pronounced effect, on swirl flow cases, with discouragement of central recirculation zones, and forward flow in highly swirled vortex core regions. The expansion ratio value has large-scale effects on the size and location of the recirculation zones.

Abujelala, M. T.↗

Suppression of Marangoni Convection in Float Zones

The basic purpose of this program is to demonstrate by means of an Earth-based 1-g experiment that the undesirable Marangoni (surface tension) convection can be suppressed or significantly reduced by means of gas jets directed tangentially to the free surface of the liquid in a float zone. These jets will establish the tangential shear stress field over the surface which must be adjusted to equal the counter-stress resultant of the Marangoni shear stress which causes the convection. For proposed materials processing in space (o-g), particularly of important, highly reactive semiconductor materials, e.g., silicon, microgravity will virtually eliminate the unwanted thermal-buoyancy convection in the liquid silicon, but will have no effect in reducing the Marangoni convection. Unless this can be sufficiently suppressed by other means, there may be no significant advantages to the proposed space processing of reactive semiconductors. Although some inert gas such as argon must be used for the corrosive liquid silicon, the Earth-based experiment uses air jets and various transparent oils, since the basic principle involved is the same. The first float zone is enclosed in a very small rectangular box with a quasi-planar free surface. Stable Marangoni convection has been achieved and velocities measured photographically. The air jet system with variable velocity and temperature is under construction. Three independent parameters must be optimized to attain maximum suppression: the gas velocity, angle of attack, and gas temperature.

Dressler, R. F.↗

Lateral jet injection into typical combustor flowfields

The experimental problem of lateral jet injection into typical flow fields in the absence of combustion was studied. All flow fields being investigated have no expansion of the crossflow (the test section to swirler diameter ratio D/d = 1), after its passage through an optional swirler (with swirl vane angle phi = 0 (swirler removed), 45, and 70 degree). The lateral jet(s) is(are) located one test-section diameter downstream of the test-section inlet (x/D = 1). The lateral jets have round-sectioned nozzles, each of which has an area of 1/100th of the cross sectional area of the crossflow (A sub j/A sub c = 1/100). Jet-to-crossflow velocity ratios of R = v sub j/u sub o = 2, 4, and 6 were investigated. Helium-bubble low visualization, five-hole pitot probe time-mean velocity measurements, and single-wire time-mean velocity and normal and shear stress turbulence data were obtained in the research program.

Lilley, D. G.↗

The Tukey algorithm for enhancing MST radar data

One of the most troublesome features in MSR (mesosphere stratosphere troposphere) velocity measurements is the determination of unwanted scatterer whose velocity is different from that of the surrounding atmosphere. Aircraft seen in the sidelobes of the antenna are the principal problem. Because coherent integration essentially eliminates echoes with line of sight velocities greater than 10 or 20 m/s, aircraft are seen only when their flight path is almost perpendicular to the line of sight. Then, they give large returns whose velocities may be positive or negative, and certainly different from that of the surrounding air. The glitches in the minute by minute velocity records are quite troublesome in that they may distort the statistics of the velocity. An objective way is therefore needed to remove sporadic points of this kind. For this purpose, the Tukey algorithm is appropriate and has some advantages over averaging. The Tukey algorithm, applied to a data array, uses for each data point the median of it and the two points surrounding it. If the three points form a monotonically increasing or decreasing sequence, the original point is copied with change. However, if the central point is remote from the other two, it is replaced by whichever of the two surrounding points is closest in value. The greatest effect of the Tukey algorithm is on data where the successive points are uncorrelated. Examples are given.

Bowhill, S. A.↗

An experimental study of the aerodynamics of a NACA 0012 airfoil with a simulated glaze ice accretion

An experimental study was conducted in the Ohio State University subsonic wind tunnel to measure the detailed aerodynamic characteristics of an airfoil with a simulated glaze ice accretion. A NACA 0012 model with interchangeable leading edges and pressure taps every one percent chord was used. Surface pressure and wake data were taken on the airfoil clean, with forced transition and with a simulated glaze ice shape. Lift and drag penalties due to the ice shape were found and the surface pressure clearly showed that large separation bubbles were present. Both total pressure and split-film probes were used to measure velocity profiles, both for the clean model and for the model with a simulated ice accretion. A large region of flow separation was seen in the velocity profiles and was correlated to the pressure measurements. Clean airfoil data were found to compare well to existing airfoil analysis methods.

Bragg, M. B.↗

Laser transit anemometer measurements on a slender cone in the Langley unitary plan wind tunnel

A laser transit anemometer (LTA) system was used to probe the boundary layer on a slender (5 degree half angle) cone model in the Langley unitary plan wind tunnel. The anemometer system utilized a pair of laser beams with a diameter of 40 micrometers spaced 1230 micrometers apart to measure the transit times of ensembles of seeding particles using a cross-correlation technique. From these measurements, boundary layer profiles around the model were constructed and compared with CFD calculations. The measured boundary layer profiles representing the boundary layer velocity normalized to the edge velocity as a function of height above the model surface were collected with the model at zero angle of attack for four different flow conditions, and were collected in a vertical plane that bisected the model's longitudinal center line at a location 635 mm from the tip of the forebody cone. The results indicate an excellent ability of the LTA system to make velocity measurements deep into the boundary layer. However, because of disturbances in the flow field caused by onboard seeding, premature transition occurred implying that upstream seeding is mandatory if model flow field integrity is to be maintained. A description and results of the flow field surveys are presented.

Humphreys, William M., Jr.↗

Comparison of frequency domain and time domain laser velocimeter signal processors

An experimental investigation was conducted in the 14- by 22-foot subsonic tunnel at NASA-Langley Research Center to measure the inflow into a scale model helicopter rotor in forward flight. These inflow measurements were acquired utilizing a two-component laser velocimeter, and the data were processed by a frequency-domain processor (FDP). As a subset of the experiment, a time-domain counter processor was utilized simultaneously with an FDP to make a comparison of the two processors possible. The results indicate that the FDP had a marked improvement in processing capability in conditions of low signal-to-noise ratios and had a reduction in the number of erroneous data points acquired. However, the FDP yielded a lower data rate in comparison to the counter when signal-to-noise ratios were high. Comparison of the data sets shows that the FDP consistantly measures velocities which are 0.7 percent higher than those measured by the counter processor.

Mace, W. D., Jr.↗

Exploratory Experiments to Probe the Effect of Bulk Density and Porosity on The Morphology and Ejecta Kinematics of Impact Craters

The morphometry of relatively small impact craters are influenced by the physical properties of the target. To investigate the control of bulk density and porosity on the crater-formation processing the gravity regime, we conducted a series of impact experiments, varying each these target parameters while holding the other constant. Three different sands were used to construct cohesionless targets: quartz (0.4-0.8 mm), garnet (0.425-1.0 mm), and alumina (0.297-0.71mm), representing a range of intrinsic grain densities from 2.65 to 4.02 g cm-3. High-porosity targets were constructed by carefully pouring the sand into the center of a cylindrical PVC target bucket (inner diameter 26.2 cm, height 12 cm) and allowing it to fill the bucket at the angle of repose before being leveled flat at the top of the bucket. Low-porosity targets were obtained by pluviation of the granular material through a 1 mm sieve that was set directly above the target bucket. With the disparate intrinsic densities of the sand in combination with the variations of the packing technique, we attained differences in the bulk-target density of up to 32%while keeping porosity constant. The impact experiments were conducted with the vertical gun in the Experimental Impact Laboratory at NASA Johnson Space Center; using 3/16” (4.76 mm) diameter aluminum projectiles launched at1.55 ± 0.03 km s-1. The ejecta were observed using the laser-based Ejection Velocity Measurement System, providing data on launch positions and velocities of ejected particles. Submillimeter topographic data of the resulting craters were collected after each experiment with a NextEngine 3D scanner. Regardless of target material or density, all craters exhibited a simple bowl shape, but a trend of increasing depth-diameter ratio with increasing target porosity is observed across the entire experimental suite. Despite these morphometric differences, ejecta launch angles and speeds remain remarkably similar amongst all of the target configurations.

impact cratering↗

Cluster Observations for Combined X-Ray and Sunyaev-Zel'dovich Estimates of Peculiar Velocities and Distances

Measurements of the peculiar velocities of galaxy clusters with respect to the Hubble flow allow the determination of the gravitational field from all matter in the universe, not just the visible component. The Sunyaev-Zel'dovich (SZ) effect (the inverse-Compton scattering of cosmic microwave background photons by the hot gas in clusters of galaxies) allows these velocities to be measured without the use of empirical distance indicators. Additionally, because the magnitude of the SZ effect is independent of redshift, the technique can be used to measure velocities out to the epoch of cluster formation. The SZ technique requires a determination of the temperature of the hot cluster gas from X-ray observations, and measurements of the SZ effect at millimeter wavelengths to separate the contribution from the thermal motions within the gas from that of the cluster peculiax velocity. We have constructed a bolometric receiver, the Sunyaev-Zel'dovich Infrared Experiment, specifically to make measurements of the SZ effect at millimeter wavelengths in order to apply the SZ technique to peculiar velocity measurements. This receiver has already been used to set limits to the peculiar velocities of two galaxy clusters at z approx. 0.2. As a test of the SZ technique, the double cluster pair Abell 222 and 223 was selected for observation. Measurements of the redshifts of the two components suggest that, if the clusters are gravitationally bound, they should exhibit a relative velocity of 10OO km/ s, well above the expected precision of 200 km/ s (set by astrophysical confusion) that is expected from the SZ method. The temperature can be measured from ASCA data which we obtained for this cluster pair. However, in order to ensure that the temperature estimate from the ASCA data was not dominated by cooling flows within the cluster, we requested ROSAT HRI observations of this cluster pair. Analysis of the X-ray properties of the cluster pair is continuing by combining the ROSAT observations funded under this proposal, archival PSPC data and our own PI ASCA data. The imaging data shows that neither cluster has a strong cooling flow, although A223 is the more compact of the two components. A223 also has a sub-cluster projected 1 Mpc to the North. The observed properties of this cluster pair are strikingly similar to those of the well-studied pair of A399 and A401 which are widely believed to be interacting and are in the initial stages of merging. This strengthens our selection of this cluster pair as a test for cluster peculiar motions. Combining these X-ray observations with SUZIE measurements of the SZ effect will provide important constraints on cluster merger models. This part of the program has been heavily delayed by bad weather at Mauna Kea, however SZ observations were obtained in November 1997 as part of a separately funded effort. These data are currently being analyzed.

Lange, A. E.↗

An experimental study of the flow field surrounding a subsonic jet in a cross flow

An experimental investigation of the flow interaction of a 5.08 cm (2.00 in.) diameter round subsonic jet exhausting perpendicularly to a flat plate in a subsonic cross flow was conducted in the NASA Ames 7x1O ft. Wind Tunnel Number One. Flat plate surface pressures were measured at 400 locations in a 30.48 cm (12.0 in.) concentric circular array surrounding the jet exit. Results from these measurements are provided in tabular and graphical form for jet-to-crossflow velocity ratios ranging from 4 to 12, and for jet exit Mach numbers ranging from 0.50 to 0.93. Laser doppler velocimeter (LDV) three component velocity measurements were made in selected regions in the developed jet plume and near the flat plate surface, at a jet Mach number of 0.50 and jet-to-crossflow velocity ratios of 6 and 8. The results of both pressure and LDV measurements are compared with the results of previous experiments. In addition, pictures of the jet plume shape at jet velocity ratios ranging from 4 to 12 were obtained using schleiren photography. The LDV measurements are consistent with previous work, but more extensive measurements will be necessary to provide a detailed picture of the flow field. The surface pressure results compare closely with previous work and provide a useful characterization of jet induced surface pressures. The results demonstrate the primary influence of jet velocity ratio and the secondary influence of jet Mach number in determining such surface pressures.

Dennis, Robert Foster↗

Integrating Experiments and Well Logs to Predict Caney Shale Static Mechanical Properties During Production with Supervised Machine Learning

Caney shale is one of the emerging oil reservoirs in Oklahoma. Understanding the impact of effective stress on its mechanical properties is critical for predicting hydraulic fracture geometry and overall hydrocarbon production. The objective of our study is to evaluate the impact of effective stress on the dynamic Young’s modulus using ultrasonic velocity measurements for Caney shale samples. A triaxial cell was utilized to measure ultrasonic (P-wave and S-wave) velocities for ten downhole Caney shale samples under various effective stresses to indirectly assess the impact of pore pressure change. The dynamic Young’s moduli estimated from these measurements were integrated with available conventional well logs (excluding sonic logs) and triaxial test results from Benge et al. (2021) to predict the static Young’s modulus using Random Forest (RF) and Extreme Gradient Boosting (XGBoost) models. The results showed that the estimated dynamic Young’s moduli from ultrasonic measurements were higher than the corresponding static Young’s modulus of cores from the same vertical well at similar depths. With increasing effective stress, the dynamic Young’s modulus increased for all samples. The estimated dynamic-to-static correction factor tended to be higher in zones of high neutron porosity (PHIN) and low density compared to other zones. Finally, SHapley Additive exPlanations (SHAP) for RF and XGBoost models identified depth, gamma ray (GR), and PHIN as key features for predicting the static Young’s modulus. This study enhances our understanding of the dynamic and static Young’s moduli for the Caney shale interval, as a function of effective stress and conventional well logs. The findings from this study can improve predictions of production throughout the well's lifespan by offering insights into the mechanical property degradation resulting from pore pressure depletion.

Kholy, Sherif M.↗

Full waveform analysis for high pressure ultrasonic measurement

In this paper we report a data analysis protocol for ultrasonic velocity measurements carried out in a synchrotron x-ray facility based multi-anvil high-pressure apparatus. Synthetic ultrasonic signals for the time period between echoes from the two ends of the sample assembly are created with a few simple parameters as the echo waveform is modeled by the first echo from the anvil-assembly boundary. Each echo is modeled as a delta function with an amplitude and arrival time and convolved with this waveform. The final waveform, fit to the data, enables analysis of signals with overlapped echoes as they are common in small cell assemblies and high pressure.

47 OTHER INSTRUMENTATION↗