SEARCH · Engineering Papers

Results for “Thermal performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42

All sources NASA NTRS DOE OSTI

NASA NTRS2019

Operation of a Heat Pipe with Multiple Heat Loads Under Reflux Mode

"Heat pipes are being used on many spacecraft to acquire heat dissipated by the payload and transport the heat to a remote radiator. In instrument-level or spacecraft-level ground testing, many heat pipes are placed in a gravity-driven reflux mode where the condenser is well above the evaporator, resulting in the formation of a liquid pool at the bottom of the heat pipe. If a head load is applied to a site that is in contact with the liquid pool, the generated vapor will flow upward to the condenser and the condensate will fall back to the evaporator due the influence of gravity. Hence, the heat pipe can operate steadily under reflux mode because the heated site always has sufficient liquid supply to sustain the fluid flow. In contrast, when a heat load is applied to a site remote from the liquid pool, the heat pipe will be unable to transfer heat through liquid evaporation unless the heated site has a chance to be in contact with liquid. This can be accomplished by applying an additional heat load to the liquid pool to establish a reflux flow so that the remote site can capture the falling condensate. An experimental investigation was conducted to study the effect of gravity on the thermal performance of a heat pipe under reflux mode with multiple heat loads. An aluminum ammonia heat pipe with internal axial grooves was placed in a vertical position. Cooling was provided to the top of the heat pipe, and heat was applied to three sites below the condenser with various heat distributions. One of the heated sites was above the liquid pool, and two were in direct contact with the liquid pool. Test results showed that when a heat load was applied to either one or both of the lower sites, the heat pipe could run steadily under reflux mode. After a reflux flow had been established, a heat load could be applied to the upper site. If the upper site could capture sufficient liquid falling from the condenser to handle its heat load solely by liquid evaporation, the heat pipe could reach steady operation. Otherwise, the temperature of the upper site would oscillate due to its intermittent contact with the falling liquid. For a given heat load to the upper site, the amplitude of temperature oscillation decreased with an increasing heat load to the lower sites because there was more falling condensate available for the upper site to capture. Moreover, the temperature oscillation disappeared completely when the total heat loads to lower sites exceeded a threshold power, and the threshold power increased with an increasing heat load to the upper site."

Ku, Jentung↗

NASA NTRS2001

TES cryocooler system design and development

This paper describes the cryogenic system design including the cryogenic loads, thermal performance margins, and performance properties for the cryocoolers.

tropospheric↗

NASA NTRS2017

Development of a Turn Key Cryogenic Cooling Module for Space Flight Based on a Commercial Cryocooler

Commercial cryocoolers have significant price and lead time advantages over coolers built exclusively for the space market, but there are many challenges that must be overcome before using a COTS cooler for flight. The initial cost advantage is significantly narrowed by the cost of adapting the COTS cooler for flight. JPL is developing a “turnkey” cryogenic cooling solution based on a commercial cryocooler with the intention that it can become a standard product. The goal is to develop a complete, fully redundant cryogenic cooling solution based on the Thales 9310. The system includes the cooler, brackets to provide mounting and cooling, supporting structures, vibration isolation, thermal straps, thermal switches, and drive electronics. This paper discusses qualification of the various components for flight, including launch vibration and thermal performance testing, as well as a full up testing of the completed assembly.

Ramsey, Perry G.↗

NASA NTRS2017

Development of a Turn Key Cryogenic Cooling Module for Space Flight Based on a Commercial Cryocooler

Commercial cryocoolers have significant price and lead time advantages over coolers built exclusively for the space market, but there are many challenges that must be overcome before using a COTS cooler for flight. The initial cost advantage is significantly narrowed by the cost of adapting the COTS cooler for flight. JPL is developing a “turn key” cryogenic cooling solution based on a commercial cryocooler with the intention that it can become a standard product. The goal is to develop a complete, fully redundant cryogenic cooling solution based on the Thales 9310. The system includes the cooler, brackets to provide mounting and cooling, supporting structures, vibration isolation, thermal straps, thermal switches, and drive electronics. This paper discusses qualification of the various components for flight, including launch vibration and thermal performance testing, as well as a full up testing of the completed assembly.

Ramsey, Perry G.↗

NASA NTRS2018

Characterization Testing of Lockheed Martin Micro1-2 Cryocoolers Optimized for 220 K Environment

The Mapping Imaging Spectrometer for Europa (MISE) Instrument on the Europa Clipper mission has baselined a Lockheed Martin high-power Micro1-2 pulse tube cryocooler operating at 135 Hz with a 220 K heat rejection temperature. This paper describes the testing and results of two Lockheed Martin Micro1-2 coolers optimized for these conditions. The thermal performance of the microcoolers was measured in vacuum for heat reject temperatures between 220 and 230 K. The coolers were operated with input powers ranging from 5 W to 40 W and drive frequency between 125 Hz and 145 Hz. The optimal drive frequency was strongly dependent on heat reject temperature. In addition, the exported forces and torques of the coolers were measured at 300 K heat rejection for input powers ranging from 5 W to 60 W and drive frequency between 120 Hz and 160 Hz. The exported forces were dependent on both piston amplitude and drive frequency. Moreover, the following were measured on one of the coolers: DC and AC magnetic fields at various locations, the off-state conductance of the pulse tube, and the effect of inclination angle of the pulse tube relative to gravity on the performance of the cooler. Finally, one of the coolers was subjected to random vibration testing.

Rodriguez, J.I.↗

NASA NTRS2019

Thermal design of the sample handling assembly in the sampling and caching subsystem on the Mars 2020 rover

The Mars 2020 Rover is scheduled to land on Mars on February 18, 2021. One of the primary mission objectives for the Mars 2020 Rover is to collect a set of Martian regolith samples for potential future return to Earth. Regolith and rock samples will be collected and placed into sample tubes using a coring drill, located at the end of a large Robotic Arm, on the outside of the rover. Filled sample tubes will be transferred from the outside of the Rover into the Adaptive Caching Assembly (ACA), located inside the Rover chassis, via the Bit Carousel. Once the filled sample tube is brought into the ACA, the Sample Handling Assembly (SHA) will transfer it to all of the internal processing stations of the ACA for volume assessment, sealing and finally drop-off on the Martian surface. The ACA is a volume within the rover chassis that is not temperature-controlled. Actuators inside the SHA and its End Effector (EE) must be warmed to above -55°C and -25°C, respectively, prior to use. This paper discusses the thermal design of the SHA that uses heaters and temperature sensors to warm up and maintain the temperature-sensitive arm components within temperature limits during operation. Thermal performance predictions for Mars surface operations are also presented.

Lee, Chern-Jiin↗

NASA NTRSDate not supplied

Solar Absorptivity Degradation of Spacecraft Materials Due to UV and Charged Particles in the Gateway Environment

The Gateway Passive Thermal Control System (PTCS) Group has identified charged particle and UV degradation of Gateway materials as a knowledge gap for the Near Rectilinear Halo Orbit (NRHO) and transit environment. Candidate materials and coatings were subjected to expected mission UV and charged particle environments at NASA Goddard Space Flight Center (GSFC). In situ change in reflectivity was observed at specified intervals during testing such that change in solar absorptivity could be plotted as a function of time of solar exposure. Gateway will be an outpost in cislunar space designed to survive a 15-year mission to support human moon landings and future deep space exploration. The Gateway Passive Thermal Control System (PTCS) Group has identified charged particle and UV degradation of potential Gateway materials as a knowledge gap for the Near Rectilinear Halo Orbit (NRHO) and transit environment, especially the slow spiral transit planned for the first two modules. Solar absorptivity degradation is important to quantify because the end-of-life absorptivity impacts thermal performance of the system. To address this, ground testing is being completed at NASA Goddard Space Flight Center in which potential Gateway materials, including radiators, multi-layer insulation (MLI), and structural materials are subjected to the expected transit plus 15-year on-orbit charged particle fluence (9.86x1015 protons/cm2 at 2.5 keV and 3.1x1016 electrons/cm2 at 10 keV) and up to 5000 Equivalent Solar Hours (ESH). Reflectivity of a single sample of each material was measured in atmosphere and in vacuum inside the chamber after exposure to incremental levels of ESH and charged particle fluence. Increase in absorptivity of most samples were seen throughout the test including large differences in absorptivity of materials of the same category. Future testing will validate these results and include additional materials of interest.

materials in the space environment↗

NASA NTRSDate not supplied

Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Mission Overview, Science Return, and Future Applications of This Technology

The Low-Earth Orbit (LEO) Flight Test of an Inflatable Decelerator (LOFTID) mission was the culmination of two decades of research and development for Hyper-sonic Inflatable Aerodynamic Decelerator (HIAD) technology. LOFTID was a project overseen by the Technology Demonstration Mission (TDM) program within NASA’s Space Technology Mission Directorate. The success of the LOFTID mission could enable new NASA missions to Mars, Venus, and most solar-system destinations with atmospheres, as well as cost-effective payload returns to Earth, including in-space manufactured materials and launch vehicle asset recovery. LOFTID, with its unique inflatable heat shield, was the first-of-a-kind orbital reentry flight, and the largest blunt body atmospheric entry of any kind. On November 10, 2022, just over 10 years since the previous flight test of the smaller sub-orbital Inflatable Reentry Vehicle Experiment-3 (IRVE-3) [1], NASA Langley Research Center, with partner United Launch Alliance (ULA), successfully launched and achieved reentry and recovery of the LOFTID Reentry Vehicle (RV), further demonstrating the viability of the HIAD technology for large-diameter, inflatable heat shields to safely and accurately deliver large payloads through an atmosphere via a controlled descent and landing. Launching as a secondary payload with the Joint Polar Satellite System 2 (JPSS-2) from Vandenberg Space Force Base, California, stowed inside an ex-tended payload adapter of the Atlas V 401 launch vehicle, the LOFTID mission officially began after the JPSS-2 payload was delivered to its orbit by the Centaur second stage. The LOFTID RV was flying solo on its spin-stabilized ballistic reentry trajectory about one hour after launch, and the flight ended approximately one hour later with a gentle splashdown under parachute in the Pacific Ocean off the east coast of Hawaii, where the RV was recovered and later shipped back to NASA Langley. LOFTID endured the harsh environments of atmospheric reentry while demonstrating stable aerodynamics through the entire spectrum of hypersonic, supersonic, transonic, and subsonic flight. The LOFTID RV was exposed to an aeroheating environment representative of many Mars and LEO HIAD applications, while successfully demonstrating the ability of the heat-affected inflatable structure to with-stand aerodynamic forces that exceeded those expected at Mars. This flight demonstration of a 6m diameter HIAD confirmed the technology structural and thermal performance as it protected the 1100kg RV entering Earth’s atmosphere at 8 km/s, reaching Mach 30, and experiencing 9g deceleration before deploying parachutes and splashing down in the Pacific Ocean. HIAD technology involves an aeroshell that can be hard packed into a small volume for launch and then deployed prior to atmospheric entry for a controlled deceleration through the atmosphere. Large deployable heat shields enable spacecraft to carry bigger, heavier payloads, including scientific instruments and human support systems for planetary landing and exploration. Much larger than traditional fixed diameter aeroshells that are constrained by the size of launch vehicle shrouds, inflatable decelerators create more drag and start the deceleration process in the upper reaches of the atmosphere with greater efficiency and stability. LOFTID’s successful demonstration of the HIAD technology has greatly expanded NASA’s options for future planetary missions and opened new commercial opportunities for lower-cost mission pay-load recovery including recovery of launch vehicle assets, or as a delivery system to return cargo from the International Space Station or cislunar space. The developments for some of these applications are al-ready underway. While LOFTID was indeed a first-of-a-kind flight for an inflatable heatshield, the largest blunt-body entry ever, its remarkable performance assured that it will not be the last of its kind.

John DiNonno↗

NASA NTRSDate not supplied

Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Mission Overview and Science Return

The Low-Earth Orbit (LEO) Flight Test of an Inflatable Decelerator (LOFTID) mission was the culmination of two decades of research and development led by NASA Langley Research Center for Hypersonic Inflatable Aerodynamic Decelerator (HIAD) technology. A HIAD aeroshell can be hard packed into a small volume for launch and then deployed prior to atmospheric entry for stable aerodynamic deceleration through the atmosphere. Much larger than traditional fixed diameter aeroshells that are constrained by the size of launch vehicle shrouds, inflatable decelerators create more drag and start the deceleration process in the upper reaches of the atmosphere with greater efficiency and stability. Large deployable heatshields enable spacecraft to carry bigger, heavier payloads, including scientific instruments and human support systems for planetary landing and exploration. The success of the LOFTID mission could enable new NASA missions to Mars (including access to higher altitudes than currently possible), Venus, and most solar system destinations with atmospheres, as well as cost-effective payload returns to Earth. With its unique 6m diameter inflatable heatshield, LOFTID was the first-of-a-kind orbital reentry flight, and the largest blunt body atmospheric entry of any kind. On November 10, 2022, the LOFTID aeroshell endured the harsh environments of atmospheric reentry while exhibiting stable aerodynamics through the entire spectrum of hypersonic, supersonic, transonic, and subsonic flight. The demonstration confirmed the HIAD technology structural and thermal performance as the aeroshell protected the 1100 kg Reentry Vehicle (RV) entering Earth’s atmosphere at 8 km/s, reaching Mach 30, and experiencing 9.5 g deceleration before deploying parachutes and gently splashing down in the Pacific Ocean, where it was recovered in excellent condition. The LOFTID aeroshell was exposed to an aeroheating environment representative of many Mars and LEO HIAD applications, and successfully demonstrated the ability of the heat-affected inflatable structure to withstand aerodynamic forces that exceeded those expected at Mars. This mission further demonstrated the viability of HIAD technology to deliver large payloads safely and accurately through an atmosphere via a controlled entry, descent, and landing. Whereas LOFTID was indeed a first-of-a-kind flight for an inflatable heatshield, its remarkable performance assured that it will not be the last of its kind.

J M Dinonno↗

NASA NTRSDate not supplied

Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) Mission Overview and Science Return

John M DiNonno↗

NASA NTRSDate not supplied

Implementation of a Hybrid Edge Node-Centroid Node Approach for the Generation of Reduced Thermal Models

Reduced thermal models are often required for delivery to organizations that manage observatory or launch models at the highest levels of assembly. However, the effort to generate reduced models, and verify against their detailed counterparts, is a challenge that has not yet been conclusively solved. Higher level organizations often place a limit on the number of nodes for delivered models with the assumption that smaller models generally result in less computation time. However, the burden of producing and verifying the accuracy of the reduced models is placed primarily on the lower-level organizations, which in turn consumes resources needed to produce these models. Limiting the total number of allowable nodes may also prevent users from taking full advantage of software capabilities that allow for faster generation of models, such as finite elements, which generally require more nodes than older centroid based models. A methodology using Thermal Desktop was described in 2010 which used: (1) finite elements and edge nodes for a conduction matrix, (2) centroid nodes for capacitance and radiative computations, and (3) the super network feature to produce a conduction matrix based only on the centroid nodes. At that time, the methodology was clear, but the implementation would have had to be done manually; however, with the inclusion of the OpenTD API, this methodology can now be implemented programmatically and for the first time, be a viable approach for the generation of reduced models. The approach was implemented and developed at the NASA Goddard Space Flight Center (GSFC) for the Capture, Containment, and Return System (CCRS) payload on the Earth Return Orbiter (ERO) as part of the Mars Sample Return (MSR) mission, resulting in the TCYEE tool. ERO features a spacecraft bus provided by Airbus through the European Space Agency (ESA) with node limitations on the delivered CCRS model provided by GSFC. TCYEE was used to generate the reduced model for this delivery and the predictions compared favorably to the detailed model currently in use for the thermal performance evaluation. Furthermore, TCYEE is being explored for potential use on the Roman Space Telescope (RST) for the generation of reduced models for delivery to the launch provider, which also has node limit requirements on the RST observatory model for use in launch simulation analyses. This paper describes the methodology, its implementation, and compares the performance of reduced models generated by TCYEE to their detailed counterparts.

Hume L. Peabody↗

NASA NTRSDate not supplied

Continuation of Solar Absorptivity Degradation of Spacecraft Materials Due to UV and Charged Particles in the Gateway Environment

Gateway is a lunar orbiting platform that will be assembled in space similar to the International Space Station. Modules will arrive following different transit orbits, some of which have an extended duration in the Van Allen Belts. This means the spacecraft is exposed to significant charged particle radiation, after which it must operate in cislunar space for 15 years. Charged particle and UV degradation of potential Gateway materials was identified as a knowledge gap by the Passive Thermal Control System (PTCS) Group as end-of-life solar absorptivity greatly impacts thermal performance. Multiple rounds of ground testing have been completed at NASA Goddard Space Flight Center in which potential Gateway materials were subjected to expected worst-case transit charged particle fluence (9.86x1015 protons/cm2 at 2.5 keV and 3.1x1016 electrons/cm2 at 10 keV) and up to 5093 Equivalent Solar Hours (ESH) of UV exposure. This report builds on previous data from Zinecker et al. 2022 which presented the first round of ground testing. Additional materials have been tested and solar absorptivity degradation along with lessons learned are shared. Comparisons to previous results are also presented.

Brandon Hoffmann↗

NASA NTRSDate not supplied

Estimation of End-of-Life Solar Absorptivity for Complex, Multi-Phased Space Missions

Solar absorptivity degradation over time is an important contributor to the thermal performance of a spacecraft at the end of its life. When environments are complex and include many different factors known to impact solar absorptivity degradation, such as UV, charged particles, contamination, or lunar dust coverage, combining data from several different studies can be done to estimate total degradation. While the most conservative way is to stack delta absorptivity from each factor to come up with a total delta, this may be overly conservative for long or complex missions with multiple mission phases. As absorptivity increases the rate of degradation decreases, and synergistic effects need to be taken into account. In this report an alternate method is proposed using Gateway materials as an example. This method determines which environmental factor will be dominant at what time (such as contamination or charged particles) and uses that degradation rate for that mission phase. For the next mission phase, the new absorptivity can be used instead of the original BOL absorptivity to determine degradation rate. This approach prevents overestimating optical degradation when considering degradation from interconnected sources.

Brandon Michael Hoffmann↗

NASA NTRSDate not supplied

Thermal, Structural, and Rotordynamics Refinements to the Superconducting Rotor of A 1.4 Mw Partially Superconducting Machine for Electrified Aircraft

NASA is developing the high efficiency megawatt motor (HEMM), a 1.4 MW partially superconducting machine, to ad-dress the need for highly efficient, lightweight, MW-class ma-chines to support aviation sustainability efforts. This paper presents progress on the thermal, structural, and rotordynamics aspects of HEMM’s superconducting rotor. Emissivity measurements of gold coated cobalt iron and titanium parts are presented and then used to correlate a thermal model of the rotor to existing data from a thermo-electrical test of the full-scale rotor. Lessons learned from the correlated model are presented, including a rank ordering of the contributors to the temperature of the superconducting coils. An updated structural design of the HEMM rotor is presented and compared to the prior design. Finite element analysis demonstrates that the updated design improves stress margins while reducing magnetic flux leakage and retaining thermal performance. The key conclusions of the rotordynamics design are presented.

electrified aircraft propulsion↗

NASA NTRS2024

Continuation of Solar Absorptivity Degradation of Spacecraft Materials Due to UV and Charged Particles in the Gateway Environment

Gateway is a lunar orbiting platform that will be assembled in space similar to the International Space Station. Modules will arrive following different transit orbits, some of which have an extended duration in the Van Allen Belts. This means the spacecraft is exposed to significant charged particle radiation, after which it must operate in cislunar space for 15 years. Charged particle and UV degradation of potential Gateway materials was identified as a knowledge gap by the Passive Thermal Control System (PTCS) Group as end-of-life solar absorptivity greatly impacts thermal performance. Multiple rounds of ground testing have been completed at NASA Goddard Space Flight Center in which potential Gateway materials were subjected to expected worst-case transit charged particle fluence (9.86 x 10 15 protons/cm 2 at 2.5 keV and 3.1x10 16 electrons/cm 2 at 10 keV) and up to 5093 Equivalent Solar Hours (ESH) of UV exposure. This report builds on previous data from Zinecker et al. 2022. Round 1a was published in that paper and Rounds 2a, 2b, and 2c are discussed here with some comparisons to Round 1a. Additional materials have been tested and solar absorptivity degradation is presented along with comparisons to previous results.

Brandon Hoffmann↗

NASA NTRS2024

Development of Cryogenic Phase Change Materials for Lunar Sample Return

One of the scientific goals of NASA’s Artemis missions is to return regolith samples from the lunar surface. To maintain scientific integrity of these samples, including any volatiles that may exist, cryogenic stowage is desired. FROSTE (Frozen Return Of Samples To Earth) is the element of the Moon to Mars architecture that is tasked with developing and advancing concepts related to this goal. Both active and passive solutions are being considered, but active solutions (cryo-coolers) have high mass and cost penalties. Phase change materials (PCMs) are commonly used as passive thermal management solutions, particularly for sensitive scientific samples. However, there are currently no PCMs capable of providing cooling at the cryogenic temperatures needed to enable lunar sample return with volatiles intact (<120 K). FROSTE has identified two possible candidate materials that could fill this gap. Testing is required to verify the thermal performance of these materials, as well as gain experience with their handling characteristics. We are conducting this testing at the Marshall Space Flight Center’s Space Environmental Effects laboratory, in vacuum, with liquid nitrogen providing cooling ability below the freezing point of the materials. In this talk, we will present an overview of the FROSTE program element and share results from the initial development testing of two cryogenic phase change materials.

phase change material↗

NASA NTRS2025

Lucy L’Ralph In-Flight Calibration and Results at (152830) Dinkinesh

The L'Ralph instrument is a key component of NASA's Lucy mission, intended to provide spectral image data of multiple Jupiter Trojans. The instrument operates from ∼0.35 to 4 μm using two focal plane assemblies: a 350–950 nm multispectral imager, Multi-spectral Visible Imaging Camera (MVIC), and a 0.97–4 μm imaging spectrometer, Linear Etalon Imaging Spectral Array (LEISA). Instrument calibration was established through ground testing before launch and has been monitored during cruise utilizing internal calibration sources and stellar targets. In-flight data have shown that the instrument thermal performance is exceeding expectations, allowing for early updates to LEISA radiometric and pointing calibrations. MVIC radiometric performance remains stable more than 3 yr since launch. The serendipitous identification of a new flyby target, (152830) Dinkinesh, allowed testing of instrument performance and interleaved LEISA and MVIC acquisitions on an asteroid target. Both MVIC and LEISA obtained data of Dinkinesh and its moon, Selam, demonstrating that they show good spectral agreement with an S- or Sq-type asteroid, along with evidence of a 3 μm absorption feature.

Amy A Simon↗

NASA NTRS1985

A program for the calculation of paraboloidal-dish solar thermal power plant performance

A program capable of calculating the design-point and quasi-steady-state annual performance of a paraboloidal-concentrator solar thermal power plant without energy storage was written for a programmable calculator equipped with suitable printer. The power plant may be located at any site for which a histogram of annual direct normal insolation is available. Inputs required by the program are aperture area and the design and annual efficiencies of the concentrator; the intercept factor and apparent efficiency of the power conversion subsystem and a polynomial representation of its normalized part-load efficiency; the efficiency of the electrical generator or alternator; the efficiency of the electric power conditioning and transport subsystem; and the fractional parasitic loses for the plant. Losses to auxiliaries associated with each individual module are to be deducted when the power conversion subsystem efficiencies are calculated. Outputs provided by the program are the system design efficiency, the annualized receiver efficiency, the annualized power conversion subsystem efficiency, total annual direct normal insolation received per unit area of concentrator aperture, and the system annual efficiency.

Bowyer, J. M., Jr.↗